Balance declarations of pci_request_regions() and pci_release_regions() with
empty inline definitions for the CONFIG_PCI=n case -- otherwise my patch to
drivers/net/3c59x.c in the -mm tree doesn't compile. :-)
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Functions marked __devinit will be removed after kernel init.  But being
exported they are potentially called by a module much later.

So the safer choice seems to be to keep the function even in the non
CONFIG_HOTPLUG case.

This silence the follwoing section mismatch warnings:
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_add_device from __ksymtab_gpl between '__ksymtab_pci_bus_add_device' (at offset 0x20) and '__ksymtab_pci_walk_bus'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_create_bus from __ksymtab_gpl between '__ksymtab_pci_create_bus' (at offset 0x40) and '__ksymtab_pci_stop_bus_device'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_max_busnr from __ksymtab_gpl between '__ksymtab_pci_bus_max_busnr' (at offset 0xc0) and '__ksymtab_pci_assign_resource_fixed'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_claim_resource from __ksymtab_gpl between '__ksymtab_pci_claim_resource' (at offset 0xe0) and '__ksymtab_pcie_port_bus_type'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_add_devices from __ksymtab between '__ksymtab_pci_bus_add_devices' (at offset 0x70) and '__ksymtab_pci_bus_alloc_resource'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_scan_bus_parented from __ksymtab between '__ksymtab_pci_scan_bus_parented' (at offset 0x90) and '__ksymtab_pci_root_buses'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_assign_resources from __ksymtab between '__ksymtab_pci_bus_assign_resources' (at offset 0x4d0) and '__ksymtab_pci_bus_size_bridges'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_size_bridges from __ksymtab between '__ksymtab_pci_bus_size_bridges' (at offset 0x4e0) and '__ksymtab_pci_setup_cardbus'
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently, there is no minimum number of fields required when adding
a new device ID to a PCI driver through the new_id sysfs file. It is
possible to add a new ID with only the vendor ID set, causing the
driver to attempt to attach to all PCI devices from that vendor. This
has been reported to happen accidentally:
  http://lists.lm-sensors.org/pipermail/lm-sensors/2007-March/019366.html
It is even possible to not even set the vendor ID field, causing the
driver to attempt to attach to _all_ the PCI devices.

This sounds dangerous and I fail to see any valid use of this
"feature". Thus I suggest that we now require at least the first two
fields (vendor ID and device ID) to be set. For what it's worth, this
is what the USB subsystem does.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

At one time, if a BIOS ROM shadow was detected for the boot video
device (stored at offset 0xc0000), we'd set a special resource flag,
IORESOURCE_ROM_SHADOW, so that the sysfs ROM file code could handle
it properly.  That broke along the way somewhere though, so current
kernels will be missing 'rom' files in sysfs if the video device
doesn't have an explicit ROM BAR.

This patch fixes the regression by moving the video fixup quirk to a
little later in the boot cycle (to avoid having its work undone by
PCI resource allocation) and checking in the PCI sysfs code whether
a rom file should be created due to a shadow resource, which is also
moved to a little later in the boot cycle so it will occur after the
video fixup.  Tested and works on my i386 test box.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Warning(linux-2621-rc3g7/drivers/pci/pci.c:1283): No description found for parameter 'dev'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.

In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.

My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:

arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c

I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.

Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
  [PATCH] scatterlist.h needs types.h
  http://lkml.org/lkml/2007/3/01/141Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Most architectures' scatterlist.h use the type dma_addr_t, but omit to
include <asm/types.h> which defines it.  This could lead to build failures,
so let's add the missing includes.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix duplicate names in shpchp and pciehp.
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adapts PCIEHP driver to PCI device driver model.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The event handler of PCIEHP driver is unnecessarily very complex. In
addition, current event handler can only a fixed number of events at
the same time, and some of events would be lost if several number of
events happened at the same time.

This patch simplify the event handler using 'work queue', and it also
fix the above-mentioned issue.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds a new API which can be used to issue various types
of PCI-E reset, including PCI-E warm reset and PCI-E hot reset.
This is needed for an ipr PCI-E adapter which does not properly
implement BIST. Running BIST on this adapter results in PCI-E
errors. The only reliable reset mechanism that exists on this
hardware is PCI Fundamental reset (warm reset). Since driving
this type of reset is architecture unique, this provides the
necessary hooks for architectures to add this support.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Acked-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a kernel bug which is triggered when using the
irqbalance daemon with MSI-X hardware.

Because both MSI-X interrupt messages and MSI-X table writes are posted,
it's possible for them to cross while in-flight.  This results in
interrupts being received long after the kernel thinks they're disabled,
and in interrupts being sent to stale vectors after rebalancing.

This patch performs a read flush after writes to the MSI-X table for
mask and unmask operations.  Since the SMP affinity is set while
the interrupt is masked, and since it's unmasked immediately after,
no additional flushes are required in the various affinity setting
routines.

This patch has been validated with (unreleased) network hardware which
uses MSI-X.

Revised with input from Eric Biederman.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Marvell IDE interface on my machine would hit a BUG_ON() in
lib/iomem.c because it was calling ata_pci_init_one() specifying just a
single port on the host, but that would actually end up trying to
initialize two ports, the second one with bogus information.

This fixes "ata_pci_init_one()" so that it actually passes down the
n_ports variable that it got from the low-level driver to the host
allocation routine ("ata_host_alloc_pinfo()"), which results in the ATA
layer actually having the correct port number information.

And in order to make it all work, I also needed to fix a few places that
had incorrectly hard-coded the fact that a host always had exactly two
ports (both ata_pci_init_bmdma() and ata_request_legacy_irqs() would
just always iterate over both ports).
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For backwards compatibility, call_platform_enable_wakeup() can return 0
instead of -EIO since we aren't guaranteed to have errno defined.

Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a kvasprintf() function to complement kasprintf().

No in-tree users yet, but I have some coming up.

[akpm@linux-foundation.org: EXPORT it]
Signed-off-by: NJeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Keir Fraser <keir@xensource.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch changes the docs and behaviour from "all states valid" to "no
states valid" if no .valid callback is assigned.  Users of pm_ops that only
need mem sleep can assign pm_valid_only_mem without any overhead, others
will require more elaborate callbacks.

Now that all users of pm_ops have a .valid callback this is a safe thing to
do and prevents things from getting messy again as they were before.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NPavel Machek <pavel@ucw.cz>
Looks-okay-to: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Almost all users of pm_ops only support mem sleep, don't check in .valid and
don't reject any others in .prepare so users can be confused if they check
/sys/power/state, especially when new states are added (these would then
result in s-t-r although they're supposed to be something different).

This patch implements a generic pm_valid_only_mem function that is then
exported for users and puts it to use in almost all existing pm_ops.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: linux-pm@lists.linux-foundation.org
Cc: Len Brown <lenb@kernel.org>
Acked-by: NRussell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch removes the firmware disk suspend mode which is the wrong approach,
it is supposed to be used for implementing firmware-based disk suspend but
cannot actually be used for that.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Len Brown <lenb@kernel.org>
Acked-by: NRussell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch series cleans up some misconceptions about pm_ops.  Some users of
the pm_ops structure attempt to use it to stop the user from entering suspend
to disk, this, however, is not possible since the user can always use
"shutdown" in /sys/power/disk and then the pm_ops are never invoked.  Also,
platforms that don't support suspend to disk simply should not allow
configuring SOFTWARE_SUSPEND (read the help text on it, it only selects
suspend to disk and nothing else, all the other stuff depends on PM).

The pm_ops structure is actually intended to provide a way to enter
platform-defined sleep states (currently supported states are "standby" and
"mem" (suspend to ram)) and additionally (if SOFTWARE_SUSPEND is configured)
allows a platform to support a platform specific way to enter low-power mode
once everything has been saved to disk.  This is currently only used by ACPI
(S4).

This patch:

The pm_ops.pm_disk_mode is used in totally bogus ways since nobody really
seems to understand what it actually does.

This patch clarifies the pm_disk_mode description.

It also removes all the arm and sh users that think they can veto suspend to
disk via pm_ops; not so since the user can always do echo shutdown >
/sys/power/disk, they need to find a better way involving Kconfig or such.

ACPI is the only user left with a non-zero pm_disk_mode.

The patch also sets the default mode to shutdown again, but when a new pm_ops
is registered its pm_disk_mode is selected as default, that way the default
stays for ACPI where it is apparently required.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: NRussell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We're getting lockdep warnings due to a post-2.6.21-rc7 bugfix.

The xattr_sem can never be taken in the manner described. Internal inodes
are protected by I_PRIVATE.  Add the appropriate annotation.

Cc: <stable@kernel.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Today's print_symbol function dumps a kernel symbol with printk.  This
patch extends the functionality of kallsyms.c so that the symbol lookup
function may be used without the printk.  This is useful for modules that
want to dump symbols elsewhere, for example, to debugfs.  I intend to use
the new function call in the GFS2 file system (which will be a separate
patch).

[akpm@linux-foundation.org: build fix]
[clameter@sgi.com: sprint_symbol should return length of string like sprintf]
Signed-off-by: NRobert Peterson <rpeterso@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: NPaulo Marques <pmarques@grupopie.com>
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When allocating local ports, do not allow a bind to a port
with a specific local address when a bind to that port with
a wildcard local address already exists.

Noticed by Linus.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I accidently applied an earlier version of Eric Dumazet's patch, from
March 21st.  His version from March 30th didn't have these bugs, so
this just interdiffs to the correct patch.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (56 commits)
  ieee1394: remove garbage from Kconfig
  ieee1394: more help in Kconfig
  ieee1394: ohci1394: Fix mistake in printk message.
  ieee1394: ohci1394: remove unnecessary rcvPhyPkt bit flipping in LinkControl register
  ieee1394: ohci1394: fix cosmetic problem in error logging
  ieee1394: eth1394: send async streams at S100 on 1394b buses
  ieee1394: eth1394: fix error path in module_init
  ieee1394: eth1394: correct return codes in hard_start_xmit
  ieee1394: eth1394: hard_start_xmit is called in atomic context
  ieee1394: eth1394: some conditions are unlikely
  ieee1394: eth1394: clean up fragment_overlap
  ieee1394: eth1394: don't use alloc_etherdev
  ieee1394: eth1394: omit useless set_mac_address callback
  ieee1394: eth1394: CONFIG_INET is always defined
  ieee1394: eth1394: allow MTU bigger than 1500
  ieee1394: unexport highlevel_host_reset
  ieee1394: eth1394: contain host reset
  ieee1394: eth1394: shorter error messages
  ieee1394: eth1394: correct a memset argument
  ieee1394: eth1394: refactor .probe and .update
  ...

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid: (21 commits)
  USB HID: don't warn on idVendor == 0
  USB HID: add 'quirks' module parameter
  USB HID: add support for dynamically-created quirks
  USB HID: clarify static quirk handling as squirks
  USB HID: encapsulate quirk handling into hid-quirks.c
  USB HID: EMS USBII device needs HID_QUIRK_MULTI_INPUT
  HID: update copyright and authorship macro
  HID: introduce proper zeroing of unused bits in output reports
  USB HID: add support for WiseGroup MP-8800 Quad Joypad
  USB HID: add FF support for Logitech Force 3D Pro Joystick
  USB HID: numlock quirk for dell W7658 keyboard
  USB HID: Logitech MX3000 keyboard needs report descriptor quirk
  USB HID: extend quirk for Logitech S510 keyboard
  USB HID: usbkbd/usbmouse - handle errors when registering devices
  USB HID: add QUIRK_HIDDEV for Belkin Flip KVM
  HID: enable dead keys on a belkin wireless keyboard
  USB HID: Thustmaster firestorm dual power v1 support
  USB HID: specify explicit size for hid_blacklist.quirks
  USB HID: fix retry & reset logic
  USB HID: consolidate vendor/product ids
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
  [IPV4] SNMP: Support OutMcastPkts and OutBcastPkts
  [IPV4] SNMP: Support InMcastPkts and InBcastPkts
  [IPV4] SNMP: Support InTruncatedPkts
  [IPV4] SNMP: Support InNoRoutes
  [SNMP]: Add definitions for {In,Out}BcastPkts
  [TCP] FRTO: RFC4138 allows Nagle override when new data must be sent
  [TCP] FRTO: Delay skb available check until it's mandatory
  [XFRM]: Restrict upper layer information by bundle.
  [TCP]: Catch skb with S+L bugs earlier
  [PATCH] INET : IPV4 UDP lookups converted to a 2 pass algo
  [L2TP]: Add the ability to autoload a pppox protocol module.
  [SKB]: Introduce skb_queue_walk_safe()
  [AF_IUCV/IUCV]: smp_call_function deadlock
  [IPV6]: Fix slab corruption running ip6sic
  [TCP]: Update references in two old comments
  [XFRM]: Export SPD info
  [IPV6]: Track device renames in snmp6.
  [SCTP]: Fix sctp_getsockopt_local_addrs_old() to use local storage.
  [NET]: Remove NETIF_F_INTERNAL_STATS, default to internal stats.
  [NETPOLL]: Remove CONFIG_NETPOLL_RX
  ...

* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
  [PATCH] elevator: elv_list_lock does not need irq disabling
  [BLOCK] Don't pin lots of memory in mempools
  cfq-iosched: speedup cic rb lookup
  ll_rw_blk: add io_context private pointer
  cfq-iosched: get rid of cfqq hash
  cfq-iosched: tighten queue request overlap condition
  cfq-iosched: improve sync vs async workloads
  cfq-iosched: never allow an async queue idling
  cfq-iosched: get rid of ->dispatch_slice
  cfq-iosched: don't pass unused preemption variable around
  cfq-iosched: get rid of ->cur_rr and ->cfq_list
  cfq-iosched: slice offset should take ioprio into account
  [PATCH] cfq-iosched: style cleanups and comments
  cfq-iosched: sort IDLE queues into the rbtree
  cfq-iosched: sort RT queues into the rbtree
  [PATCH] cfq-iosched: speed up rbtree handling
  cfq-iosched: rework the whole round-robin list concept
  cfq-iosched: minor updates
  cfq-iosched: development update
  cfq-iosched: improve preemption for cooperating tasks

* 'for-2.6.22' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (255 commits)
  [POWERPC] Remove dev_dbg redefinition in drivers/ps3/vuart.c
  [POWERPC] remove kernel module option for booke wdt
  [POWERPC] Avoid putting cpu node twice
  [POWERPC] Spinlock initializer cleanup
  [POWERPC] ppc4xx_sgdma needs dma-mapping.h
  [POWERPC] arch/powerpc/sysdev/timer.c build fix
  [POWERPC] get_property cleanups
  [POWERPC] Remove the unused HTDMSOUND driver
  [POWERPC] cell: cbe_cpufreq cleanup and crash fix
  [POWERPC] Declare enable_kernel_spe in a header
  [POWERPC] Add dt_xlate_addr() to bootwrapper
  [POWERPC] bootwrapper: CONFIG_ -> CONFIG_DEVICE_TREE
  [POWERPC] Don't define a custom bd_t for Xilixn Virtex based boards.
  [POWERPC] Add sane defaults for Xilinx EDK generated xparameters files
  [POWERPC] Add uartlite boot console driver for the zImage wrapper
  [POWERPC] Stop using ppc_sys for Xilinx Virtex boards
  [POWERPC] New registration for common Xilinx Virtex ppc405 platform devices
  [POWERPC] Merge common virtex header files
  [POWERPC] Rework Kconfig dependancies for Xilinx Virtex ppc405 platform
  [POWERPC] Clean up cpufreq Kconfig dependencies
  ...

A transmitted IP multicast datagram should be counted as OutMcastPkts.
By the same token, a transmitted IP broadcast datagram should be
counted as OutBcastPkts.
Signed-off-by: NMitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A received IP multicast datagram should be counted as InMcastPkts.
By the same token, a received IP broadcast datagram should be
counted as InBcastPkts.
Signed-off-by: NMitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An IP datagram which is being discarded because the datagram frame
didn't carry enough data should be counted as InTruncatedPkts.
Signed-off-by: NMitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An IP datagram which is being discarded because of no routes in the
forwarding path should be counted as InNoRoutes.
Signed-off-by: NMitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The updated IP-MIB RFC (RFC4293) specifys new objects, InBcastPkts
and OutBcastPkts. This adds definitions for them.
Signed-off-by: NMitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a corner case where less than MSS sized new data thingie
is awaiting in the send queue. For F-RTO to work correctly, a
new data segment must be sent at certain point or F-RTO cannot
be used at all. RFC4138 allows overriding of Nagle at that
point.

Implementation uses frto_counter states 2 and 3 to distinguish
when Nagle override is needed.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No new data is needed until the first ACK comes, so no need to check
for application limitedness until then.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On MIPv6 usage, XFRM sub policy is enabled.
When main (IPsec) and sub (MIPv6) policy selectors have the same
address set but different upper layer information (i.e. protocol
number and its ports or type/code), multiple bundle should be created.
However, currently we have issue to use the same bundle created for
the first time with all flows covered by the case.

It is useful for the bundle to have the upper layer information
to be restructured correctly if it does not match with the flow.

1. Bundle was created by two policies
Selector from another policy is added to xfrm_dst.
If the flow does not match the selector, it goes to slow path to
restructure new bundle by single policy.

2. Bundle was created by one policy
Flow cache is added to xfrm_dst as originated one. If the flow does
not match the cache, it goes to slow path to try searching another
policy.
Signed-off-by: NMasahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SACKED_ACKED and LOST are mutually exclusive with SACK, thus
having their sum larger than packets_out is bug with SACK.
Eventually these bugs trigger traps in the tcp_clean_rtx_queue
with SACK but it's much more informative to do this here.

Non-SACK TCP, however, could get more than packets_out duplicate
ACKs which each increment sacked_out, so it makes sense to do
this kind of limitting for non-SACK TCP but not for SACK enabled
one. Perhaps the author had the opposite in mind but did the
logic accidently wrong way around? Anyway, the sacked_out
incrementer code for non-SACK already deals this issue before
calling sync_left_out so this trapping can be done
unconditionally.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some people want to have many UDP sockets, binded to a single port but
many different addresses. We currently hash all those sockets into a
single chain.  Processing of incoming packets is very expensive,
because the whole chain must be examined to find the best match.

I chose in this patch to hash UDP sockets with a hash function that
take into account both their port number and address : This has a
drawback because we need two lookups : one with a given address, one
with a wildcard (null) address.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows a name "pppox-proto-nnn" to be used in modprobe.conf
to autoload a PPPoX protocol nnn.
Signed-off-by: NJames Chapman <jchapman@katalix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>