Samsung uart driver lookups the clock using the connection id 'clk_uart_baud'.
The uart clocks for all Samsung platforms are reorganized to register them
with the lookup name as required by the uart driver.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

With clkdev based clock lookup support, the clock set and get operation
using clock names communicated between the samsung uart driver and the
SoC specific extension can be removed.

In addition to that, for each platform specific extension, add the
default clock selection, number of clock options for uart baud generator,
clock selection bit mask and shift values which is required by the
clkdev support in samsung uart driver.

The default clock selection value 'def_clk_sel' specifies the default clock
to be used as the source clock for baud rate generator in case the platform
code does not specify the same.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

With clkdev based clock lookup added to samsung serial driver, the use
of 'struct s3c24xx_uart_clksrc' to supply clock names in platform
data is removed from all the Samsung platform code.

Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Ramax Lo <ramaxlo@gmail.com>
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Instead of using clock names supplied in platform data, use a generic
clock name 'clk_uart_baud' to look up clocks. The platform code should
register clocks with the name 'clk_uart_baud' which can be used by the
baud rate generator. The clock lookup and selection of the best clock
as baud rate clock is reworked.

Platform code can specify the clocks that can be used as source for the
baud clock (as supported previously by passing names of clocks). A new
member is added to the platform data 'clk_sel' which holds a bit-field
value with each bit representing a baud source clock. If a bit at any
bit position is set, that clock is looked up to participate in the
selection of the baud clock source.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

s3c2440 uses fclk/n (fclk divided by n) clock as one of the possible clocks used
to generate the baud rate clock. The divider 'n' in this case can be logically
represented outside of the uart controller.

This patch creates a new clock by name "fclk_n" for s3c2440 based platforms to
represent the fclk/n clock in the platform code. This clock provides a get_rate
callback that checks the UCON0/1/2 registers to determine the clock rate. The
samsung uart driver would receive the "fclk_n" clock name as one of the possible
baud rate clock options and the driver need not determine clock rate of fclk/n.

Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enable conversion of device tree interrupt specifier to linux
virq domain for GIC controller.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The timer irqs statically mapped from linux irq numbers 11 to 15 are
moved to the end of the statically mapped linux irq space. The GIC PPI
and SPI interrupts are relocated to start from 16 and 32 of the linux
irq space. This is a required to add device tree support for GIC and
Interrupt combiner for EXYNOS4.

A new macro 'IRQ_TIMER_BASE' specifies a platform specific base of the
linux virq number for the timer interrupts. For exynos4, this base is
set to end of the linux virq space.  For the other S5P platforms, the
existing base '11' is retained.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The bisection implemented in unwind_find_origin() stopped to early.  If
there is only a single entry left to check the original code just took
the end point as origin which might be wrong.

This was introduced in commit de66a979 ("ARM: 7187/1: fix unwinding
for XIP kernels").
Reported-and-tested-by: NNick Bowler <nbowler@elliptictech.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

d312ae87 "xen: use maximum reservation to limit amount of usable RAM"
clamped the total amount of RAM to the current maximum reservation. This is
correct for dom0 but is not correct for guest domains. In order to boot a guest
"pre-ballooned" (e.g. with memory=1G but maxmem=2G) in order to allow for
future memory expansion the guest must derive max_pfn from the e820 provided by
the toolstack and not the current maximum reservation (which can reflect only
the current maximum, not the guest lifetime max). The existing algorithm
already behaves this correctly if we do not artificially limit the maximum
number of pages for the guest case.

For a guest booted with maxmem=512, memory=128 this results in:
 [    0.000000] BIOS-provided physical RAM map:
 [    0.000000]  Xen: 0000000000000000 - 00000000000a0000 (usable)
 [    0.000000]  Xen: 00000000000a0000 - 0000000000100000 (reserved)
-[    0.000000]  Xen: 0000000000100000 - 0000000008100000 (usable)
-[    0.000000]  Xen: 0000000008100000 - 0000000020800000 (unusable)
+[    0.000000]  Xen: 0000000000100000 - 0000000020800000 (usable)
...
 [    0.000000] NX (Execute Disable) protection: active
 [    0.000000] DMI not present or invalid.
 [    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
 [    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
-[    0.000000] last_pfn = 0x8100 max_arch_pfn = 0x1000000
+[    0.000000] last_pfn = 0x20800 max_arch_pfn = 0x1000000
 [    0.000000] initial memory mapped : 0 - 027ff000
 [    0.000000] Base memory trampoline at [c009f000] 9f000 size 4096
-[    0.000000] init_memory_mapping: 0000000000000000-0000000008100000
-[    0.000000]  0000000000 - 0008100000 page 4k
-[    0.000000] kernel direct mapping tables up to 8100000 @ 27bb000-27ff000
+[    0.000000] init_memory_mapping: 0000000000000000-0000000020800000
+[    0.000000]  0000000000 - 0020800000 page 4k
+[    0.000000] kernel direct mapping tables up to 20800000 @ 26f8000-27ff000
 [    0.000000] xen: setting RW the range 27e8000 - 27ff000
 [    0.000000] 0MB HIGHMEM available.
-[    0.000000] 129MB LOWMEM available.
-[    0.000000]   mapped low ram: 0 - 08100000
-[    0.000000]   low ram: 0 - 08100000
+[    0.000000] 520MB LOWMEM available.
+[    0.000000]   mapped low ram: 0 - 20800000
+[    0.000000]   low ram: 0 - 20800000

With this change "xl mem-set <domain> 512M" will successfully increase the
guest RAM (by reducing the balloon).

There is no change for dom0.
Reported-and-Tested-by: NGeorge Shuklin <george.shuklin@gmail.com>
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: stable@kernel.org
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The "(insn & 0x01800000) != 0x01800000" test matches 'restore'
but that is a legitimate place to see the %lo() part of a 32-bit
symbol relocation, particularly in tail calls.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Tested-by: NSergei Trofimovich <slyfox@gentoo.org>

Commit 10299e2e (ARM: RX-51:
Enable isp1704 power on/off) added power management for isp1704.

However, the transceiver should be powered on by default,
otherwise USB doesn't work at all for networking during
boot.

All kernels after v3.0 are affected.

Cc: stable@kernel.org
Signed-off-by: NFelipe Contreras <felipe.contreras@gmail.com>
Reviewed-by: NSebastian Reichel <sre@debian.org>
[tony@atomide.com: updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commits 09d28d ("ARM: OMAP: mcbsp: Start generalize omap2_mcbsp_set_clks_src")
and 7bc0c4 ("ARM: OMAP: mcbsp: Start generalize signal muxing functions")
incorrectly set two struct omap_mcbsp_platform_data fields after
omap_device_build_ss and kfree calls.

Fix this by moving these pdata assignments before those calls.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Reported-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This hangs my MacBook Air at boot time; I get no console
messages at all. I reverted this on top of -rc5 and my machine
boots again.

This reverts commit e8c71062.
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@consoleSigned-off-by: NIngo Molnar <mingo@elte.hu>

arm_dma_zone_size is used by arm_bootmem_free() which is called by
paging_init(). Thus it needs to be set before calling it.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Cc: stable@kernel.org
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

efi_call_phys_prelog() sets up a 1:1 mapping of the physical address
range in swapper_pg_dir. Instead of replacing then restoring entries
in swapper_pg_dir we should be using initial_page_table which already
contains the 1:1 mapping.

It's safe to blindly switch back to swapper_pg_dir in the epilog
because the physical EFI routines are only called before
efi_enter_virtual_mode(), e.g. before any user processes have been
forked. Therefore, we don't need to track which pgd was in %cr3 when
we entered the prelog.

The previous code actually contained a bug because it assumed that the
kernel was loaded at a physical address within the first 8MB of ram,
usually at 0x100000. However, this isn't the case with a
CONFIG_RELOCATABLE=y kernel which could have been loaded anywhere in
the physical address space.

Also delete the ancient (and bogus) comments about the page table
being restored after the lock is released. There is no locking.

Cc: Matthew Garrett <mjg@redhat.com>
Cc: Darrent Hart <dvhart@linux.intel.com>
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1323346250.3894.74.camel@mfleming-mobl1.ger.corp.intel.comSigned-off-by: NH. Peter Anvin <hpa@linux.intel.com>

With the 3.2-rc kernel, IOMMU 2M pages in KVM works.  But when I tried
to use IOMMU 1GB pages in KVM, I encountered an oops and the 1GB page
failed to be used.

The root cause is that 1GB page allocation calls gup_huge_pud() while 2M
page calls gup_huge_pmd.  If compound pages are used and the page is a
tail page, gup_huge_pmd() increases _mapcount to record tail page are
mapped while gup_huge_pud does not do that.

So when the mapped page is relesed, it will result in kernel oops
because the page is not marked mapped.

This patch add tail process for compound page in 1GB huge page which
keeps the same process as 2M page.

Reproduce like:
1. Add grub boot option: hugepagesz=1G hugepages=8
2. mount -t hugetlbfs -o pagesize=1G hugetlbfs /dev/hugepages
3. qemu-kvm -m 2048 -hda os-kvm.img -cpu kvm64 -smp 4 -mem-path /dev/hugepages
	-net none -device pci-assign,host=07:00.1

  kernel BUG at mm/swap.c:114!
  invalid opcode: 0000 [#1] SMP
  Call Trace:
    put_page+0x15/0x37
    kvm_release_pfn_clean+0x31/0x36
    kvm_iommu_put_pages+0x94/0xb1
    kvm_iommu_unmap_memslots+0x80/0xb6
    kvm_assign_device+0xba/0x117
    kvm_vm_ioctl_assigned_device+0x301/0xa47
    kvm_vm_ioctl+0x36c/0x3a2
    do_vfs_ioctl+0x49e/0x4e4
    sys_ioctl+0x5a/0x7c
    system_call_fastpath+0x16/0x1b
  RIP  put_compound_page+0xd4/0x168
Signed-off-by: NYouquan Song <youquan.song@intel.com>
Reviewed-by: NAndrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since commit 6571534b (plat-mxc: iomux-v3.h: implicitly enable
pull-up/down when that's desired) was in, the power button on imx51
babbage board stopped working because it's pulled up by mistake.
The patch removes the pull-up setting from the pad configuration for
that gpio to make the power button back to work.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

  CC      arch/arm/plat-mxc/cpufreq.o
arch/arm/plat-mxc/cpufreq.c:203: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-mxc/cpufreq.c:203: warning: data definition has no type or storage class
arch/arm/plat-mxc/cpufreq.c:203: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
arch/arm/plat-mxc/cpufreq.c:203: warning: function declaration isn't a prototype
arch/arm/plat-mxc/cpufreq.c:204: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-mxc/cpufreq.c:204: warning: data definition has no type or storage class
arch/arm/plat-mxc/cpufreq.c:204: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
arch/arm/plat-mxc/cpufreq.c:204: warning: function declaration isn't a prototype
arch/arm/plat-mxc/cpufreq.c:205: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-mxc/cpufreq.c:205: warning: data definition has no type or storage class
arch/arm/plat-mxc/cpufreq.c:205: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
arch/arm/plat-mxc/cpufreq.c:205: warning: function declaration isn't a prototype
make[1]: *** [arch/arm/plat-mxc/cpufreq.o] Error 1
make: *** [arch/arm/plat-mxc] Error 2
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NRichard Zhao <richard.zhao@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NDong Aisheng <b29396@freescale.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NJason Chen <jason.chen@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Cc: stable@kernel.org

If we encounter an efi_memory_desc_t without EFI_MEMORY_WB set
in ->attribute we currently call set_memory_uc(), which in turn
calls __pa() on a potentially ioremap'd address.

On CONFIG_X86_32 this is invalid, resulting in the following
oops on some machines:

  BUG: unable to handle kernel paging request at f7f22280
  IP: [<c10257b9>] reserve_ram_pages_type+0x89/0x210
  [...]

  Call Trace:
   [<c104f8ca>] ? page_is_ram+0x1a/0x40
   [<c1025aff>] reserve_memtype+0xdf/0x2f0
   [<c1024dc9>] set_memory_uc+0x49/0xa0
   [<c19334d0>] efi_enter_virtual_mode+0x1c2/0x3aa
   [<c19216d4>] start_kernel+0x291/0x2f2
   [<c19211c7>] ? loglevel+0x1b/0x1b
   [<c19210bf>] i386_start_kernel+0xbf/0xc8

A better approach to this problem is to map the memory region
with the correct attributes from the start, instead of modifying
it after the fact. The uncached case can be handled by
ioremap_nocache() and the cached by ioremap_cache().

Despite first impressions, it's not possible to use
ioremap_cache() to map all cached memory regions on
CONFIG_X86_64 because EFI_RUNTIME_SERVICES_DATA regions really
don't like being mapped into the vmalloc space, as detailed in
the following bug report,

	https://bugzilla.redhat.com/show_bug.cgi?id=748516

Therefore, we need to ensure that any EFI_RUNTIME_SERVICES_DATA
regions are covered by the direct kernel mapping table on
CONFIG_X86_64. To accomplish this we now map E820_RESERVED_EFI
regions via the direct kernel mapping with the initial call to
init_memory_mapping() in setup_arch(), whereas previously these
regions wouldn't be mapped if they were after the last E820_RAM
region until efi_ioremap() was called. Doing it this way allows
us to delete efi_ioremap() completely.
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@console-pimps.orgSigned-off-by: NIngo Molnar <mingo@elte.hu>

When HPET is operating in RTC mode, the TN_ENABLE bit on timer1
controls whether the HPET or the RTC delivers interrupts to irq8. When
the system goes into suspend, the RTC driver sends a signal to the
HPET driver so that the HPET releases control of irq8, allowing the
RTC to wake the system from suspend. The switchover is accomplished by
a write to the HPET configuration registers which currently only
occurs while servicing the HPET interrupt.

On some systems, I have seen the system suspend before an HPET
interrupt occurs, preventing the write to the HPET configuration
register and leaving the HPET in control of the irq8. As the HPET is
not active during suspend, it does not generate a wake signal and RTC
alarms do not work.

This patch forces the HPET driver to immediately transfer control of
the irq8 channel to the RTC instead of waiting until the next
interrupt event.
Signed-off-by: NMark Langsdorf <mark.langsdorf@amd.com>
Link: http://lkml.kernel.org/r/20111118153306.GB16319@alberich.amd.comTested-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org

arm-eabi-4.4.3-ld:--defsym zreladdr=: syntax error
make[2]: *** [arch/arm/boot/compressed/vmlinux] Error 1
make[1]: *** [arch/arm/boot/compressed/vmlinux] Error 2
make: *** [uImage] Error 2
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NJett.Zhou <jtzhou@marvell.com>

arch/arm/mach-exynos/mct.c: In function 'exynos4_timer_resources':
arch/arm/mach-exynos/mct.c:450: error: 'exynos4_mct_tick_isr' undeclared (first use in this function)
arch/arm/mach-exynos/mct.c:450: error: (Each undeclared identifier is reported only once
arch/arm/mach-exynos/mct.c:450: error: for each function it appears in.)
make[1]: *** [arch/arm/mach-exynos/mct.o] Error 1
Reported-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NChanghwan Youn <chaos.youn@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>

This patch adds remove_irq in place of disable_irq which
is correct equivalent function for setup_irq used in
exynos4_mct_tick_init.
Signed-off-by: NAmit Daniel Kachhap <amit.kachhap@linaro.org>
Tested-by: NInderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The SMDK board uses LT3591 as backlight LED driver of LTE480WV LCD.
According to the LT3591 datasheet, the switching frequency should
be 1MHz. So, PWM period is calculated by following formula:

PWM period = 1/switching frequency
	   = 1/1MHz
	   = 1000ns

Thus, the PWM backlight period should be 1000ns.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch removes duplicated slab header for pwm backlight.
arch/arm/plat-samsung/dev-backlight.c: slab.h is included
more than once.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NGreg Ungerer <gerg@uclinux.org>

If we select a symbol it should have a type declared first
otherwise in some situations the config tools get upset. They
are currently perhaps a bit too resilient which is why this
wasn't noticed initially.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20111206132811.4041.32549.stgit@bob.linux.org.ukSigned-off-by: NIngo Molnar <mingo@elte.hu>

In the unlikely case that a platform registers a PMU platform_device
when running on a CPU that is unsupported by perf, we will encounter a
NULL dereference when trying to assign the platform_device to the
cpu_pmu structure.

This patch checks that the CPU is supported by perf before assigning
the platform_device.
Reported-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The linker places the unwind tables in readonly sections. So when using
an XIP kernel these are located in ROM and cannot be modified.
For that reason the current approach to convert the relative offsets in
the unwind index to absolute addresses early in the boot process doesn't
work with XIP.

The offsets in the unwind index section are signed 31 bit numbers and
the structs are sorted by this offset. So it first has offsets between
0x40000000 and 0x7fffffff (i.e. the negative offsets) and then offsets
between 0x00000000 and 0x3fffffff. When seperating these two blocks the
numbers are sorted even when interpreting the offsets as unsigned longs.

So determine the first non-negative entry once and track that using the
new origin pointer. The actual bisection can then use a plain unsigned
long comparison. The only thing that makes the new bisection more
complicated is that the offsets are relative to their position in the
index section, so the key to search needs to be adapted accordingly in
each step.

Moreover several consts are added to catch future writes and rename the
member "addr" of struct unwind_idx to "addr_offset" to better match the
new semantic. (This has the additional benefit of breaking eventual
users at compile time to make them aware of the change.)

In my tests the new algorithm was a tad faster than the original and has
the additional upside of not needing the initial conversion and so saves
some boot time and it's possible to unwind even earlier.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NNicolas Pitre <nico@fluxnic.net>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 1b9f95f8 (ARM: prepare for removal of a bunch of <mach/memory.h>
files) introduced CONFIG_PHYS_OFFSET but the Kconfig hex prompt did not
provide a default value.

This has the undesired side effect of breaking a reportedly used
trick for updating defconfigs on the fly for routine buildtesting
across all arch and all platforms, i.e.

	cp /path/to/somedefconfig .config ; yes "" | make oldconfig

because the config system will endlessly loop until a valid address is
provided.

However we can't just pick a random default value since it is likely to
be wrong for the majority of the boards as the right answer for this
option is quite varied.  So the fact that the config system insists on
having a proper value be entered is actually a good thing.

It turns out that only at91x40_defconfig has this problem because it has
CONFIG_MMU=n. However, in the !MMU case, there is already a CONFIG_DRAM_BASE
value that can be used here.  So let's use that as a default in that case
and suppress the redundant CONFIG_PHYS_OFFSET prompt.

Eventually the DRAM_BASE config option could simply be replaced by
PHYS_OFFSET directly, but that's a larger change better suited for later.
Reported-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We currently fail to build on CONFIG_X86_INTEL_MID=y and
CONFIG_X86_MRST unset.

We could build all the bits to make generic MID work if you
picked MID platform alone but that's really silly. Instead use
select and two variables.

This looks a bit daft right now but once we add a Medfield
selection it'll start to look a good deal more sensible.
Reported-by: NIngo Molnar <mingo@elte.hu>
Reported-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20111205231433.28811.51297.stgit@bob.linux.org.ukSigned-off-by: NIngo Molnar <mingo@elte.hu>

Fix compile error due to missing <linux/module.h> include.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

Otherwise timing is inaccurate, resulting in devices which depend on it,
like omap-keypad, broken.

Tested on Amstrad Delta.
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: removed comment referencing a development branch]
Signed-off-by: NTony Lindgren <tony@atomide.com>

I've received complaints that the numa_node attribute for family
15h model 00-0fh (e.g. Interlagos) northbridge functions shows
-1 instead of the proper node ID.

Correct this with attached quirks (similar to quirks for other
AMD CPU families used in multi-socket systems).
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Cc: Frank Arnold <frank.arnold@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/20111202072143.GA31916@alberich.amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Intel MID x86 platforms have a memory mapped virtual RTC
instead.  No MID platform have the default ports (and
accessing them may do weird stuff).
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: feng.tang@intel.com
Cc: Feng Tang <feng.tang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Fix an outstanding issue that has been reported since 2.6.37.
Under a heavy loaded machine processing "fork()" calls could
crash with:

BUG: unable to handle kernel paging request at f573fc8c
IP: [<c01abc54>] swap_count_continued+0x104/0x180
*pdpt = 000000002a3b9027 *pde = 0000000001bed067 *pte = 0000000000000000 Oops: 0000 [#1] SMP
Modules linked in:
Pid: 1638, comm: apache2 Not tainted 3.0.4-linode37 #1
EIP: 0061:[<c01abc54>] EFLAGS: 00210246 CPU: 3
EIP is at swap_count_continued+0x104/0x180
.. snip..
Call Trace:
 [<c01ac222>] ? __swap_duplicate+0xc2/0x160
 [<c01040f7>] ? pte_mfn_to_pfn+0x87/0xe0
 [<c01ac2e4>] ? swap_duplicate+0x14/0x40
 [<c01a0a6b>] ? copy_pte_range+0x45b/0x500
 [<c01a0ca5>] ? copy_page_range+0x195/0x200
 [<c01328c6>] ? dup_mmap+0x1c6/0x2c0
 [<c0132cf8>] ? dup_mm+0xa8/0x130
 [<c013376a>] ? copy_process+0x98a/0xb30
 [<c013395f>] ? do_fork+0x4f/0x280
 [<c01573b3>] ? getnstimeofday+0x43/0x100
 [<c010f770>] ? sys_clone+0x30/0x40
 [<c06c048d>] ? ptregs_clone+0x15/0x48
 [<c06bfb71>] ? syscall_call+0x7/0xb

The problem is that in copy_page_range() we turn lazy mode on,
and then in swap_entry_free() we call swap_count_continued()
which ends up in:

         map = kmap_atomic(page, KM_USER0) + offset;

and then later we touch *map.

Since we are running in batched mode (lazy) we don't actually
set up the PTE mappings and the kmap_atomic is not done
synchronously and ends up trying to dereference a page that has
not been set.

Looking at kmap_atomic_prot_pfn(), it uses
'arch_flush_lazy_mmu_mode' and doing the same in
kmap_atomic_prot() and __kunmap_atomic() makes the problem go
away.

Interestingly, commit b8bcfe99 ("x86/paravirt: remove lazy
mode in interrupts") removed part of this to fix an interrupt
issue - but it went to far and did not consider this scenario.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Looks like on some Acer Aspire 1s with older bioses, reboot via bios
fails.  It works on my machine, (with BIOS version 0.3310) but
not on some others (BIOS version 0.3309).

There's a log of problems at:

  https://bbs.archlinux.org/viewtopic.php?id=124136

This patch adds a different callback to the reboot quirk table,
to allow rebooting via keybaord controller.
Reported-by: NUroš Vampl <mobile.leecher@gmail.com>
Tested-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NPeter Chubb <peter.chubb@nicta.com.au>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1323093233-9481-1-git-send-email-anarsoul@gmail.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Following is from Notes of section 11.5.3 of Intel processor
manual available at:

  http://www.intel.com/Assets/PDF/manual/325384.pdf

For the Pentium 4 and Intel Xeon processors, after the sequence of
steps given above has been executed, the cache lines containing the
code between the end of the WBINVD instruction and before the
MTRRS have actually been disabled may be retained in the cache
hierarchy. Here, to remove code from the cache completely, a
second WBINVD instruction must be executed after the MTRRs have
been disabled.

This patch provides resolution for that.

Ideally, I will like to make changes only for Pentium 4 and Xeon
processors. But, I am not finding easier way to do it.
And, extra wbinvd() instruction does not hurt much for other
processors.
Signed-off-by: NAjaykumar Hotchandani <ajaykumar.hotchandani@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Link: http://lkml.kernel.org/r/4EBD1CC5.3030008@oracle.comSigned-off-by: NIngo Molnar <mingo@elte.hu>