This is purely a cleanup patch.  This collapses some of the code required
when we configure our Tx and Rx feature sets, and makes the code more
readable and maintainable.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SFF specification for Direct Attach cable detection has now been
ratified.  Previously, DA cable detect was looking at the Twinaxial bit in
byte 9 of the SFP+ EEPROM.  The spec now defines active and passive DA
cables in byte 8 of the SFP+ EEPROM.  This patch changes the cable
detection for both 82598 and 82599 SFP+ adapters to conform to the new
spec.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SFP+ NIC (device id 0x10fb) needs a semaphore to serialize
PHY access, so our PHY init code must honor that same semaphore.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to mostly historic reasons, including a lack of reliability
of the link handling (especially with the older 8169), the
current r8169 driver emulates forced mode setting by limiting
the advertised modes.

With this change the driver allows real 10/100 forced mode
settings on the 8169 and 8101/8102.

Original idea by Vincent Steenhoute. The RTL_GIGA_MAC_VER_03
tweak was extracted from Realtek's r8169 v6.010.00 driver.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NJean Delvare <jdelvare@suse.de>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jarek pointed pppoe can call back dev_queue_xmit(), and might need
skb->dst, so its safer to unset IFF_XMIT_DST_RELEASE on ppp devices.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One point of contention in high network loads is the dst_release() performed
when a transmited skb is freed. This is because NIC tx completion calls
dev_kree_skb() long after original call to dev_queue_xmit(skb).

CPU cache is cold and the atomic op in dst_release() stalls. On SMP, this is
quite visible if one CPU is 100% handling softirqs for a network device,
since dst_clone() is done by other cpus, involving cache line ping pongs.

It seems right place to release dst is in dev_hard_start_xmit(), for most
devices but ones that are virtual, and some exceptions.

David Miller suggested to define a new device flag, set in alloc_netdev_mq()
(so that most devices set it at init time), and carefuly unset in devices
which dont want a NULL skb->dst in their ndo_start_xmit().

List of devices that must clear this flag is :

- loopback device, because it calls netif_rx() and quoting Patrick :
    "ip_route_input() doesn't accept loopback addresses, so loopback packets
     already need to have a dst_entry attached."
- appletalk/ipddp.c : needs skb->dst in its xmit function

- And all devices that call again dev_queue_xmit() from their xmit function
(as some classifiers need skb->dst) : bonding, vlan, macvlan, eql, ifb, hdlc_fr
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sysfs files for a network device can not unconditionally take the
rtnl_lock as the bonding sysfs files do.  If someone accesses those
sysfs files while the network device is being unregistered with the
rtnl_lock held we will deadlock.

So use trylock and restart_syscall to avoid this problem.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Network device sysfs files that grab the rtnl_lock unconditionally
will deadlock if accessed when the network device is being
unregistered.  So use trylock and syscall_restart to avoid this
deadlock.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Holding rtnl_lock when we are unregistering the sysfs files can
deadlock if we unconditionally take rtnl_lock in a sysfs file.  So fix
it with the now familiar patter of: rtnl_trylock and syscall_restart()
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sysctls are unregistered with the rntl_lock held making
it unsafe to unconditionally grab the the rtnl_lock.  Instead
we need to call rtnl_trylock and restart the system call
if we can not grab it.  Otherwise we could deadlock at unregistration
time.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just returning -ERESTARTSYS without a signal pending is not
good that will just leak it to userspace.  We need return
-ERESTARTNOINTR so we always restart and set signal pending
so that we fall of the fast path of syscall return and setup
the system call restart.

So use restart_syscall() which does all of this for us.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The earlier patch to fix the deadlock between a network device going
away and writing to sysfs attributes was incomplete.
- It did not set signal_pending so we would leak ERSTARTSYS to user space.
- It used ERESTARTSYS which only restarts if sigaction configures it to.
- It did not cover store and show for ifalias.

So fix all of these up and use the new helper restart_syscall so we get
the details correct on what it takes.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when we have a signal pending we have the functionality
to restart that the current system call.  There are other cases
such as nasty lock ordering issues where it makes sense to have
a simple fix that uses try lock and restarts the system call.
Buying time to figure out how to rework the locking strategy.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New packet socket feature that makes packet socket more efficient for
transmission.

- It reduces number of system call through a PACKET_TX_RING mechanism,
  based on PACKET_RX_RING (Circular buffer allocated in kernel space
  which is mmapped from user space).

- It minimizes CPU copy using fragmented SKB (almost zero copy).
Signed-off-by: NJohann Baudy <johann.baudy@gnu-log.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pdev->irq was not saved in netxen_adapter, causing request_irq()
with invalid irq number.

This was broken in commit be339aee
("netxen: fix irq tear down and msix leak.").
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/scsi/fcoe/fcoe.c

gen_estimator can overflow bps (bytes per second) with Gb links, while
it was designed with a u32 API, with a theorical limit of 34360Mbit
(2^32 bytes)

Using 64 bit intermediate avbps/brate counters can allow us to reach
this theorical limit.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds support for the PCI cards: PCIcan and PCIcanx (1, 2 or 4 channel) from Kvaser (http://www.kvaser.com).
Signed-off-by: NPer Dalen <per.dalen@cnw.se>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds support for the one or two channel CPC-PCI and CPC-PCIe
cards from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
Signed-off-by: NSebastian Haas <haas@ems-wuensche.com>
Signed-off-by: NMarkus Plessing <plessing@ems-wuensche.com>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver adds support for the SJA1000 chips connected to the
"platform bus", which can be found on various embedded systems.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NOliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the generic Socket-CAN driver for the Philips SJA1000
full CAN controller.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NOliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CAN network device driver interface provides a generic interface to
setup, configure and monitor CAN network devices. It exports a set of
common data structures and functions, which all real CAN network device
drivers should use. Please have a look to the SJA1000 or MSCAN driver
to understand how to use them. The name of the module is can-dev.ko.

Furthermore, it adds a Netlink interface allowing to configure the CAN
device using the program "ip" from the iproute2 utility suite.

For further information please check "Documentation/networking/can.txt"
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NOliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch documents the CAN netowrk device drivers interface, removes
obsolete documentation and adds some useful links to CAN resources.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NOliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for TI DaVinci EMAC driver.

TI DaVinci Ethernet Media Access Controller module is based upon
TI CPPI 3.0 DMA engine and supports 10/100 Mbps on all and Gigabit modes on
some TI devices. It supports MII/RMII and has up to 8Kbytes of internal
descriptor memory. This driver has been working on several TI devices including
DM644x, DM646x and DA830 platforms. The specs of this device are available at:
http://www.ti.com/litv/pdf/sprue24aSigned-off-by: NAnant Gole <anantgole@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need for net/icmp.h header in net/ipv4/fib_frontend.c.
This patch removes the #include net/icmp.h from it.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can update netdev_queue tx_bytes/tx_packets/tx_dropped counters instead
of dev->stats ones, to reduce number of cache lines dirtied in xmit path.

This fixes a performance problem on SMP when many different cpus take
vlan tx path.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

offsetof(struct net_device, features)=0x44
offsetof(struct net_device, stats.tx_packets)=0x54
offsetof(struct net_device, stats.tx_bytes)=0x5c
offsetof(struct net_device, stats.tx_dropped)=0x6c

Network drivers that touch dev->stats.tx_packets/stats.tx_bytes in their
tx path can slow down SMP operations, since they dirty a cache line
that should stay shared (dev->features is needed in rx and tx paths)

We could move away stats field in net_device but it wont help that much.
(Two cache lines dirtied in tx path, we can do one only)

Better solution is to add tx_packets/tx_bytes/tx_dropped in struct
netdev_queue because this structure is already touched in tx path and
counters updates will then be free (no increase in size)
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is illegal to dereference a skb after a successful ndo_start_xmit()
call. We must store skb length in a local variable instead.

Bug was introduced in 2.6.27 by commit 0abf77e5
(net_sched: Add accessor function for packet length for qdiscs)
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marching along, let's bump the version number to indicate things actually
have happened to the driver.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the generic XAUI device support for 82599 controllers.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The performance of hardware RSC is greatly reduced if the total for max rsc
descriptors multiplied by the buffer size is greater than 65535.  To
prevent this we need to adjust the max rsc descriptors appropriately.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 518a09ef (tcp: Fix recvmsg MSG_PEEK influence of
blocking behavior) lets the loop run longer than the race check
did previously expect, so we need to be more careful with this
check and consider the work we have been doing.

I tried my best to deal with urg hole madness too which happens
here:
	if (!sock_flag(sk, SOCK_URGINLINE)) {
		++*seq;
		...
by using additional offset by one but I certainly have very
little interest in testing that part.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: NFrans Pop <elendil@planet.nl>
Tested-by: NIan Zimmermann <itz@buug.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWang Tinggong <wangtinggong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FIFO1_DMA_ERR is set twice, the second should be FIFO2_DMA_ERR.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NRam Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After 2.6.29, PPC no more admits passing NULL to the dev parameter of
the DMA API. The result is a BUG followed by solid lock-up when the 
mv643xx_eth driver brings an interface up. The following patch makes 
the driver work on my Pegasos again; it is mostly a search and replace 
of NULL by mp->dev->dev.parent in dma allocation/freeing/mapping/unmapping
functions.
Signed-off-by: NGabriel Paubert <paubert@iram.es>
Acked-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>