The WM831x series of PMICs support control of initial power on
through the ON pin on the device with soft control of the pin
at other times. Represent this to userspace as KEY_POWER.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver adds support for the hardware monitoring features of
the WM831x PMICs to the hwmon API. Monitoring is provided for
the system voltages supported natively by the WM831x, the chip
temperature, the battery temperature and the auxiliary inputs
of the WM831x.

Currently no alarms are supported, though digital comparators on
the WM831x devices would allow these to be provided.

Since the auxiliary and battery temperature input scaling depends
on the system configuration the value is reported as a voltage to
userspace.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add support for the GPIO pins on the WM831x. No direct support is
currently supplied for configuring non-gpiolib functionality such
as pull configuration and alternate functions, soft configuration
of these will be provided in a future patch.

Currently use of these pins as interrupts is not supported due to
the ongoing issues with generic irq not support interrupt controllers
on interrupt driven buses. Users can directly request the interrupts
with the wm831x-specific APIs currently provided if required.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The current settings which can be used with the WM831x current sinks
can't easily be mapped between register values and currents at run
time without a lookup table since the values scale logarithmically
to match the way the human eye interprets brightness. This lookup
table is inclided in the core since several drivers need to use it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x series of devices use OTP (One Time Programmable, a type
of PROM) to store system configuration. At run time this data is
visible via registers.

Currently the only explicitly supported feature is that the unique
ID provided by every WM831x device is exported to user space via
sysfs. Other configuration data may be read by system-specific
code in the pre_init() and post_init() platform data operations.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x backlight driver requires at least the specification of the
current sink to use and a maximum current to allow them to function and
will actively interfere with other users of the regulators it uses if
misconfigured so only register the subdevice for it if this platform
data has been supplied.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x contains an auxiliary ADC with a number of switchable
inputs which is used to monitor some of the voltages and
temperatures in the system and has some external inputs which can be
used for machine specific purposes. Provide an API allowing drivers
to read values from the ADC.

An internal reference voltage is provided to allow callibration of
the ADC. This is used to calibrate the device at startup.

The hardware also supports continuous readings and digital comparators.
These are not yet supported by the driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x includes an interrupt controller managing interrupts for
the various functions on the chip. This patch adds support for the
core interrupt block on the device.

Ideally this would be supported by genirq, particularly for the
GPIOs, but currently genirq is unable to cope with controllers on
interrupt driven buses so we cut'n'paste the generic interface.
Once genirq is able to cope chips like this it should be a case
of filing the prefixes off the code and redoing wm831x-irq.c to
move over.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x series of devices are register compatible processor power
management subsystems, providing regulator and power path management
facilities along with other services like watchdog, RTC and touch
panel controllers.

This patch adds very basic support, providing basic single register
I2C access, handling of the security key and registration of the
devices.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Provide basic support for MFDs having multiple cells of a given
type with different IDs by adding an id to the mfd_cell structure
and then adding that to the id passed in to mfd_add_devices().

As it stands this approach requires that MFDs using this feature
deal with ensuring that there aren't any ID collisions resulting
from multiple MFDs of the same type being instantiated. This needs
to happen with the existing code too, but with this approach there
is a knock on effect on the IDs for non-duplicated devices.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Register ezx-pcap earlier so it can be used with cpufreq
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch corrects the support for MMCSD card detection
and read only feature for SoC DM355.

EVMDM355_ECP_VA4.pdf, from Spectrum digital, suggests that
Bit 2 and 4 should be checked for card detection. However
on the EVM, bits 1 and 3 gives this status, for MMC/SD
instance 0 and 1 respectively. The pdf also suggests that
Bit 1 and 3 should be checked for write protection. However
on the EVM bits 2 and 4 gives this status.

This document can be downloaded from
http://c6000.spectrumdigital.com/evmdm355/reve/files/EVMDM355_ECP_VA4.pdfSigned-off-by: NVipin Bhandari <vipin.bhandari@ti.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Current implementation is prone to races, this patch attempts to remove all
but one (in pcf50633_adc_sync_read).

The idea is that we need to guard the queue access only on inserting and
removing items. If we insert and there're no more items in the queue it
means that the last irq already happened and we need to trigger ADC
manually. If not, then the next conversion will be triggered by the irq
handler upon completion of the previous.
Signed-off-by: NPaul Fertser <fercerpav@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Using the default kernel "events" workqueue causes problems with
synchronous adc readings if initiated from some task on the same
workqueue.

I had a deadlock trying to use pcf50633_adc_sync_read from a
power_supply class driver because the reading was initiated from the
workqueue and it waited for the irq processing to complete (to get the
result) and that was put on the same workqueue.
Signed-off-by: NPaul Fertser <fercerpav@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Make that twl4030-pwrbutton.c driver probe with current
child creation api for twl4030.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver provides reporting of the status supply voltage rails
of the WM835x series of PMICs via the hwmon API.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add (partial) support for the voltage regulators on the PCAP2 PMIC.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Provides an atomic set_bits functions, as needed by the pcap-regulator
driver.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Mask interrupts before servicing them and loop while pcap asserts the interrupt
line.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some TS controller bits are on the same register as the ADC control, save
TS specific bits and export a set_ts_bits function so the TS driver can set
it with the adc_mutex lock held.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Export an irq_to_pcap function to get pcap irq number, for the keypad driver.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The file_operations write prototype should return a ssize_t.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Unfortunatly, the upstream company has abandonded development of this
driver.  So it's best to just remove the driver from the tree.

Cc: Christopher Harrer <charrer@alacritech.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Intel has officially abandoned this project and does not want to
maintian it or have it included in the main kernel tree, as no one
should use the code, it's not needed anymore.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is already an in-kernel driver for this hardware (since 2.6.30),
at76c50x-usb, and it supports all of the same devices.  So this driver
can now be deleted.

Acked-by: Kalle Valo <kalle.valo@iki.fi> 
Cc: linux-wireless <linux-wireless@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

No one cares, it's a custom userspace interface, and the code hasn't
built in a long time.  So remove it.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The comedi drivers should be used instead, no need to have
these in here as well.

Cc: David Kiliani <mail@davidkiliani.de>
Cc: Meilhaus Support <support@meilhaus.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The comedi drivers should be used instead, no need to have
this driver in the tree duplicating that one.

Cc: Wolfgang Beiter <w.beiter@aon.at>
Cc: Guenter Gebhardt <g.gebhardt@meilhaus.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

find_first_zero_bit returns a positive value, use it accordingly.
Signed-off-by: NFrederik Deweerdt <frederik.deweerdt@xprog.eu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Line6 pod.c: Minor style cleanups
Signed-off-by: NFrederik Deweerdt <frederik.deweerdt@xprog.eu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Error handling code following a kmalloc or kzalloc should free the
allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@

x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...x...+> }
(
x->f1 = E
|
 (x->f1 == NULL || ...)
|
 f(...,x->f1,...)
)
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>

Error handling code following a kmalloc or kzalloc should free the
allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@

x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...x...+> }
(
x->f1 = E
|
 (x->f1 == NULL || ...)
|
 f(...,x->f1,...)
)
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>

amcc allocation may fail, prevent a NULL dereference.

allocation may fail, prevent a dereference.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix this build error:
undefined reference to "__this_module"
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Similarly as it has been done in other in-kernel Ralink drivers
and in openSUSE's rt3090sta package.

Cc: Axel Koellhofer <rain_maker@root-forum.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch ports a change recently applied to rt2860/rt2870 in order to
change handling of WPA1/WPA2 mixed mode to rt3090.
Signed-off-by: NAxel Koellhofer <rain_maker@root-forum.org>
Acked-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch sets "wlan" as the default suffix for naming the device, a
change which has also been previously applied to rt2860/rt2870 in
staging.
Signed-off-by: NAxel Koellhofer <rain_maker@root-forum.org>
Acked-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Both drivers (rt2860 and rt3090) register themselves as "rt2860" on
loading the module.

In the very rare case of somebody having two cards in his machine, one
using rt3090 and the other one using the rt2860 driver, loading both
modules would be impossible, the second one will not be loaded as the
kernel will tell you that the driver is already registered.

This was also present with rt2870/rt3070 (with both driver registering
as "rt2870"), but the code has been merged to one driver recently.

The follwoing patch fixes this potential problem until merging of
rt2860/rt3090 code to a single driver.
Signed-off-by: NAxel Koellhofer <rain_maker@root-forum.org>
Acked-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>