Don't pull tasks from a group if that would cause the group's total load to
drop below its total cpu_power (ie.  cause the group to start going idle).
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NNick Piggin <npiggin@suse.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Jack Steiner brought this issue at my OLS talk.

Take a scenario where two tasks are pinned to two HT threads in a physical
package.  Idle packages in the system will keep kicking migration_thread on
the busy package with out any success.

We will run into similar scenarios in the presence of CMP/NUMA.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In sys_sched_yield(), we cache current->array in the "array" variable, thus
there's no need to dereference "current" again later.
Signed-Off-By: NRenaud Lienhart <renaud.lienhart@free.fr>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If an idle sibling of an HT queue encounters a busy sibling, then make
higher level load balancing of the non-idle variety.

Performance of multiprocessor HT systems with low numbers of tasks
(generally < number of virtual CPUs) can be significantly worse than the
exact same workloads when running in non-HT mode.  The reason is largely
due to poor scheduling behaviour.

This patch improves the situation, making the performance gap far less
significant on one problematic test case (tbench).
Signed-off-by: NNick Piggin <npiggin@suse.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

During periodic load balancing, don't hold this runqueue's lock while
scanning remote runqueues, which can take a non trivial amount of time
especially on very large systems.

Holding the runqueue lock will only help to stabilise ->nr_running, however
this doesn't do much to help because tasks being woken will simply get held
up on the runqueue lock, so ->nr_running would not provide a really
accurate picture of runqueue load in that case anyway.

What's more, ->nr_running (and possibly the cpu_load averages) of remote
runqueues won't be stable anyway, so load balancing is always an inexact
operation.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Similarly to the earlier change in load_balance, only lock the runqueue in
load_balance_newidle if the busiest queue found has a nr_running > 1.  This
will reduce frequency of expensive remote runqueue lock aquisitions in the
schedule() path on some workloads.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

William Weston reported unusually high scheduling latencies on his x86 HT
box, on the -RT kernel.  I managed to reproduce it on my HT box and the
latency tracer shows the incident in action:

                 _------=> CPU#
                / _-----=> irqs-off
               | / _----=> need-resched
               || / _---=> hardirq/softirq
               ||| / _--=> preempt-depth
               |||| /
               |||||     delay
   cmd     pid ||||| time  |   caller
      \   /    |||||   \   |   /
      du-2803  3Dnh2    0us : __trace_start_sched_wakeup (try_to_wake_up)
        ..............................................................
        ... we are running on CPU#3, PID 2778 gets woken to CPU#1: ...
        ..............................................................
      du-2803  3Dnh2    0us : __trace_start_sched_wakeup <<...>-2778> (73 1)
      du-2803  3Dnh2    0us : _raw_spin_unlock (try_to_wake_up)
        ................................................
        ... still on CPU#3, we send an IPI to CPU#1: ...
        ................................................
      du-2803  3Dnh1    0us : resched_task (try_to_wake_up)
      du-2803  3Dnh1    1us : smp_send_reschedule (try_to_wake_up)
      du-2803  3Dnh1    1us : send_IPI_mask_bitmask (smp_send_reschedule)
      du-2803  3Dnh1    2us : _raw_spin_unlock_irqrestore (try_to_wake_up)
        ...............................................
        ... 1 usec later, the IPI arrives on CPU#1: ...
        ...............................................
  <idle>-0     1Dnh.    2us : smp_reschedule_interrupt (c0100c5a 0 0)

So far so good, this is the normal wakeup/preemption mechanism.  But here
comes the scheduler anomaly on CPU#1:

  <idle>-0     1Dnh.    2us : preempt_schedule_irq (need_resched)
  <idle>-0     1Dnh.    2us : preempt_schedule_irq (need_resched)
  <idle>-0     1Dnh.    3us : __schedule (preempt_schedule_irq)
  <idle>-0     1Dnh.    3us : profile_hit (__schedule)
  <idle>-0     1Dnh1    3us : sched_clock (__schedule)
  <idle>-0     1Dnh1    4us : _raw_spin_lock_irq (__schedule)
  <idle>-0     1Dnh1    4us : _raw_spin_lock_irqsave (__schedule)
  <idle>-0     1Dnh2    5us : _raw_spin_unlock (__schedule)
  <idle>-0     1Dnh1    5us : preempt_schedule (__schedule)
  <idle>-0     1Dnh1    6us : _raw_spin_lock (__schedule)
  <idle>-0     1Dnh2    6us : find_next_bit (__schedule)
  <idle>-0     1Dnh2    6us : _raw_spin_lock (__schedule)
  <idle>-0     1Dnh3    7us : find_next_bit (__schedule)
  <idle>-0     1Dnh3    7us : find_next_bit (__schedule)
  <idle>-0     1Dnh3    8us : _raw_spin_unlock (__schedule)
  <idle>-0     1Dnh2    8us : preempt_schedule (__schedule)
  <idle>-0     1Dnh2    8us : find_next_bit (__schedule)
  <idle>-0     1Dnh2    9us : trace_stop_sched_switched (__schedule)
  <idle>-0     1Dnh2    9us : _raw_spin_lock (trace_stop_sched_switched)
  <idle>-0     1Dnh3   10us : trace_stop_sched_switched <<...>-2778> (73 8c)
  <idle>-0     1Dnh3   10us : _raw_spin_unlock (trace_stop_sched_switched)
  <idle>-0     1Dnh1   10us : _raw_spin_unlock (__schedule)
  <idle>-0     1Dnh.   11us : local_irq_enable_noresched (preempt_schedule_irq)
  <idle>-0     1Dnh.   11us < (0)

we didnt pick up pid 2778! It only gets scheduled much later:

   <...>-2778  1Dnh2  412us : __switch_to (__schedule)
   <...>-2778  1Dnh2  413us : __schedule <<idle>-0> (8c 73)
   <...>-2778  1Dnh2  413us : _raw_spin_unlock (__schedule)
   <...>-2778  1Dnh1  413us : trace_stop_sched_switched (__schedule)
   <...>-2778  1Dnh1  414us : _raw_spin_lock (trace_stop_sched_switched)
   <...>-2778  1Dnh2  414us : trace_stop_sched_switched <<...>-2778> (73 1)
   <...>-2778  1Dnh2  414us : _raw_spin_unlock (trace_stop_sched_switched)
   <...>-2778  1Dnh1  415us : trace_stop_sched_switched (__schedule)

the reason for this anomaly is the following code in dependent_sleeper():

                /*
                 * If a user task with lower static priority than the
                 * running task on the SMT sibling is trying to schedule,
                 * delay it till there is proportionately less timeslice
                 * left of the sibling task to prevent a lower priority
                 * task from using an unfair proportion of the
                 * physical cpu's resources. -ck
                 */
[...]
                        if (((smt_curr->time_slice * (100 - sd->per_cpu_gain) /
                                100) > task_timeslice(p)))
                                        ret = 1;

Note that in contrast to the comment above, we dont actually do the check
based on static priority, we do the check based on timeslices.  But
timeslices go up and down, and even highprio tasks can randomly have very
low timeslices (just before their next refill) and can thus be judged as
'lowprio' by the above piece of code.  This condition is clearly buggy.
The correct test is to check for static_prio _and_ to check for the
preemption priority.  Even on different static priority levels, a
higher-prio interactive task should not be delayed due to a
higher-static-prio CPU hog.

There is a symmetric bug in the 'kick SMT sibling' code of this function as
well, which can be solved in a similar way.

The patch below (against the current scheduler queue in -mm) fixes both
bugs.  I have build and boot-tested this on x86 SMT, and nice +20 tasks
still get properly throttled - so the dependent-sleeper logic is still in
action.

btw., these bugs pessimised the SMT scheduler because the 'delay wakeup'
property was applied too liberally, so this fix is likely a throughput
improvement as well.

I separated out a smt_slice() function to make the code easier to read.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch implements a task state bit (TASK_NONINTERACTIVE), which can be
used by blocking points to mark the task's wait as "non-interactive".  This
does not mean the task will be considered a CPU-hog - the wait will simply
not have an effect on the waiting task's priority - positive or negative
alike.  Right now only pipe_wait() will make use of it, because it's a
common source of not-so-interactive waits (kernel compilation jobs, etc.).
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

whitespace cleanups.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add relevant checks into find_idlest_group() and find_idlest_cpu() to make
them return only the groups that have allowed CPUs and allowed CPUs
respectively.
Signed-off-by: NM.Baris Demiray <baris@labristeknoloji.com>
Signed-off-by: NNick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The hyperthread aware nice handling currently puts to sleep any non real
time task when a real time task is running on its sibling cpu.  This can
lead to prolonged starvation by having the non real time task pegged to the
cpu with load balancing not pulling that task away.

Currently we force lower priority hyperthread tasks to run a percentage of
time difference based on timeslice differences which is meaningless when
comparing real time tasks to SCHED_NORMAL tasks.  We can allow non real
time tasks to run with real time tasks on the sibling up to per_cpu_gain%
if we use jiffies as a counter.

Cleanups and micro-optimisations to the relevant code section should make
it more understandable as well.
Signed-off-by: NCon Kolivas <kernel@kolivas.org>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add ability to clear statistics.
Signed-off-by: NPaul Fulghum <paulkf@microgate.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The cpusets-formalize-intermediate-gfp_kernel-containment patch
has a deadlock problem.

This patch was part of a set of four patches to make more
extensive use of the cpuset 'mem_exclusive' attribute to
manage kernel GFP_KERNEL memory allocations and to constrain
the out-of-memory (oom) killer.

A task that is changing cpusets in particular ways on a system
when it is very short of free memory could double trip over
the global cpuset_sem semaphore (get the lock and then deadlock
trying to get it again).

The second attempt to get cpuset_sem would be in the routine
cpuset_zone_allowed().  This was discovered by code inspection.
I can not reproduce the problem except with an artifically
hacked kernel and a specialized stress test.

In real life you cannot hit this unless you are manipulating
cpusets, and are very unlikely to hit it unless you are rapidly
modifying cpusets on a memory tight system.  Even then it would
be a rare occurence.

If you did hit it, the task double tripping over cpuset_sem
would deadlock in the kernel, and any other task also trying
to manipulate cpusets would deadlock there too, on cpuset_sem.
Your batch manager would be wedged solid (if it was cpuset
savvy), but classic Unix shells and utilities would work well
enough to reboot the system.

The unusual condition that led to this bug is that unlike most
semaphores, cpuset_sem _can_ be acquired while in the page
allocation code, when __alloc_pages() calls cpuset_zone_allowed.
So it easy to mistakenly perform the following sequence:
  1) task makes system call to alter a cpuset
  2) take cpuset_sem
  3) try to allocate memory
  4) memory allocator, via cpuset_zone_allowed, trys to take cpuset_sem
  5) deadlock

The reason that this is not a serious bug for most users
is that almost all calls to allocate memory don't require
taking cpuset_sem.  Only some code paths off the beaten
track require taking cpuset_sem -- which is good.  Taking
a global semaphore on the main code path for allocating
memory would not scale well.

This patch fixes this deadlock by wrapping the up() and down()
calls on cpuset_sem in kernel/cpuset.c with code that tracks
the nesting depth of the current task on that semaphore, and
only does the real down() if the task doesn't hold the lock
already, and only does the real up() if the nesting depth
(number of unmatched downs) is exactly one.

The previous required use of refresh_mems(), anytime that
the cpuset_sem semaphore was acquired and the code executed
while holding that semaphore might try to allocate memory, is
no longer required.  Two refresh_mems() calls were removed
thanks to this.  This is a good change, as failing to get
all the necessary refresh_mems() calls placed was a primary
source of bugs in this cpuset code.  The only remaining call
to refresh_mems() is made while doing a memory allocation,
if certain task memory placement data needs to be updated
from its cpuset, due to the cpuset having been changed behind
the tasks back.
Signed-off-by: NPaul Jackson <pj@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch (written by me and also containing many suggestions of Arjan van
de Ven) does a major cleanup of the spinlock code.  It does the following
things:

 - consolidates and enhances the spinlock/rwlock debugging code

 - simplifies the asm/spinlock.h files

 - encapsulates the raw spinlock type and moves generic spinlock
   features (such as ->break_lock) into the generic code.

 - cleans up the spinlock code hierarchy to get rid of the spaghetti.

Most notably there's now only a single variant of the debugging code,
located in lib/spinlock_debug.c.  (previously we had one SMP debugging
variant per architecture, plus a separate generic one for UP builds)

Also, i've enhanced the rwlock debugging facility, it will now track
write-owners.  There is new spinlock-owner/CPU-tracking on SMP builds too.
All locks have lockup detection now, which will work for both soft and hard
spin/rwlock lockups.

The arch-level include files now only contain the minimally necessary
subset of the spinlock code - all the rest that can be generalized now
lives in the generic headers:

 include/asm-i386/spinlock_types.h       |   16
 include/asm-x86_64/spinlock_types.h     |   16

I have also split up the various spinlock variants into separate files,
making it easier to see which does what. The new layout is:

   SMP                         |  UP
   ----------------------------|-----------------------------------
   asm/spinlock_types_smp.h    |  linux/spinlock_types_up.h
   linux/spinlock_types.h      |  linux/spinlock_types.h
   asm/spinlock_smp.h          |  linux/spinlock_up.h
   linux/spinlock_api_smp.h    |  linux/spinlock_api_up.h
   linux/spinlock.h            |  linux/spinlock.h

/*
 * here's the role of the various spinlock/rwlock related include files:
 *
 * on SMP builds:
 *
 *  asm/spinlock_types.h: contains the raw_spinlock_t/raw_rwlock_t and the
 *                        initializers
 *
 *  linux/spinlock_types.h:
 *                        defines the generic type and initializers
 *
 *  asm/spinlock.h:       contains the __raw_spin_*()/etc. lowlevel
 *                        implementations, mostly inline assembly code
 *
 *   (also included on UP-debug builds:)
 *
 *  linux/spinlock_api_smp.h:
 *                        contains the prototypes for the _spin_*() APIs.
 *
 *  linux/spinlock.h:     builds the final spin_*() APIs.
 *
 * on UP builds:
 *
 *  linux/spinlock_type_up.h:
 *                        contains the generic, simplified UP spinlock type.
 *                        (which is an empty structure on non-debug builds)
 *
 *  linux/spinlock_types.h:
 *                        defines the generic type and initializers
 *
 *  linux/spinlock_up.h:
 *                        contains the __raw_spin_*()/etc. version of UP
 *                        builds. (which are NOPs on non-debug, non-preempt
 *                        builds)
 *
 *   (included on UP-non-debug builds:)
 *
 *  linux/spinlock_api_up.h:
 *                        builds the _spin_*() APIs.
 *
 *  linux/spinlock.h:     builds the final spin_*() APIs.
 */

All SMP and UP architectures are converted by this patch.

arm, i386, ia64, ppc, ppc64, s390/s390x, x64 was build-tested via
crosscompilers.  m32r, mips, sh, sparc, have not been tested yet, but should
be mostly fine.

From: Grant Grundler <grundler@parisc-linux.org>

  Booted and lightly tested on a500-44 (64-bit, SMP kernel, dual CPU).
  Builds 32-bit SMP kernel (not booted or tested).  I did not try to build
  non-SMP kernels.  That should be trivial to fix up later if necessary.

  I converted bit ops atomic_hash lock to raw_spinlock_t.  Doing so avoids
  some ugly nesting of linux/*.h and asm/*.h files.  Those particular locks
  are well tested and contained entirely inside arch specific code.  I do NOT
  expect any new issues to arise with them.

 If someone does ever need to use debug/metrics with them, then they will
  need to unravel this hairball between spinlocks, atomic ops, and bit ops
  that exist only because parisc has exactly one atomic instruction: LDCW
  (load and clear word).

From: "Luck, Tony" <tony.luck@intel.com>

   ia64 fix
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NArjan van de Ven <arjanv@infradead.org>
Signed-off-by: NGrant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>
Signed-off-by: NMikael Pettersson <mikpe@csd.uu.se>
Signed-off-by: NBenoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

pcibus_to_cpumask expands into more than just an initialiser so gcc
moans about code before variable declarations.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

*** Warning: "bit_spin_lock" [fs/ntfs/ntfs.ko] undefined!
*** Warning: "bit_spin_unlock" [fs/ntfs/ntfs.ko] undefined!

Cc: Anton Altaparmakov <aia21@cantab.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This shouldn't be a BUG.  We should cope.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If you try to assemble an array with too many missing devices, raid10 will now
reject the attempt, instead of allowing it.

Also check when hot-adding a drive and refuse the hot-add if the array is
beyond hope.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There was another case where sb_size wasn't being set, so instead do the
sensible thing and set if when filling in the content of a superblock.  That
ensures that whenever we write a superblock, the sb_size MUST be set.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

[PATCH] md: make sure the new 'sb_size' is set properly device added without pre-existing superblock.

There are two ways to add devices to an md/raid array.

  It can have superblock written to it, and then given to the md driver,
  which will read the superblock (the new way)

or

  md can be told (through SET_ARRAY_INFO) the shape of the array, and
  the told about individual drives, and md will create the required
  superblock (the old way).

The newly introduced sb_size was only set for drives being added the
new way, not the old ways.  Oops :-(
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Just like failed drives have (F), so spare drives now have (S).
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Leave it unchanged if the original (0.90) is used, incase it might be a
compatability problem.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Doh.  I want the physical hard-sector-size, not the current block size...
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

On reflection, a better default location for hot-adding bitmaps with version-1
superblocks is immediately after the superblock.  There might not be much room
there, but there is usually atleast 3k, and that is a good start.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The bitmap code used to have two daemons, so there is some 'common' start/stop
code.  But now there is only one, so the common code is just noise.

This patch tidies this up somewhat.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

mddev->bitmap gets clearred before the writeback daemon is stopped.  So the
write_back daemon needs to be careful not to dereference the 'bitmap' if it is
NULL.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Switch MD to use the kthread infrastructure, to simplify the code and get rid
of tasklist_lock abuse in md_unregister_thread.

Also don't flush signals in md_thread, as the called thread will always do
that.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is a direct port of the raid5 patch.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Most awkward part of this is delaying write requests until bitmap updates have
been flushed.

To achieve this, we have a sequence number (seq_flush) which is incremented
each time the raid5 is unplugged.

If the raid thread notices that this has changed, it flushes bitmap changes,
and assigned the value of seq_flush to seq_write.

When a write request arrives, it is given the number from seq_write, and that
write request may not complete until seq_flush is larger than the saved seq
number.

We have a new queue for storing stripes which are waiting for a bitmap flush
and an extra flag for stripes to record if the write was 'degraded' and so
should not clear the a bit in the bitmap.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

version-1 superblocks are not (normally) 4K long, and can be of variable size.
 Writing the full 4K can cause corruption (but only in non-default
configurations).

With this patch the super-block-flavour can choose a size to read, and set a
size to write based on what it finds.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

These inlines haven't been used for ages, they should go.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

read_sb_page() assumed that if sync_page_io fails, the device would be marked
faultly.  However it isn't.  So in the face of error, read_sb_page would loop
forever.

Redo the logic so that this cannot happen.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

As this is used to flag an internal bitmap.

Also, introduce symbolic names for feature bits.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It is possibly (and occasionally useful) to have a raid1 without persistent
superblocks.  The code in add_new_disk for adding a device to such an array
always tries to read a superblock.

This will obviously fail.

So do the appropriate test and call md_import_device with
appropriate args.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When hot-adding a bitmap, bitmap_daemon_work could get called while the bitmap
is being created, so don't set mddev->bitmap until the bitmap is ready.

This requires freeing the bitmap inside bitmap_create if creation failed
part-way through.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The 'lastrun' time wasn't being initialised, so it could be half a
jiffie-cycle before it seemed to be time to do work again.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A state of 0 mean 'not quiesced'
A state of 1 means 'is quiesced'

The original code got this wrong.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

linear currently uses division by the size of the smallest componenet device
to find which device a request goes to.  If that smallest device is larger
than 2 terabytes, then the division will not work on some systems.

So we introduce a pre-shift, and take care not to make the hash table too
large, much like the code in raid0.

Also get rid of conf->nr_zones, which is not needed.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If a device is flagged 'WriteMostly' and the array has a bitmap, and the
bitmap superblock indicates that write_behind is allowed, then write_behind is
enabled for WriteMostly devices.

Write requests will be acknowledges as complete to the caller (via b_end_io)
when all non-WriteMostly devices have completed the write, but will not be
cleared from the bitmap until all devices complete.

This requires memory allocation to make a local copy of the data being
written.  If there is insufficient memory, then we fall-back on normal write
semantics.
Signed-Off-By: NPaul Clements <paul.clements@steeleye.com>
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This allows a device in a raid1 to be marked as "write mostly".  Read requests
will only be sent if there is no other option.
Signed-off-by: NNeil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>