Make _rs_collect_tx_data get window as param, in order
to be able to set various windows.

This will be used later for saving tpc statistics
as well.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently RTS protection was done whenever trasnmitting an AMPDU.
This limits throughput in cases where there's no need for protection.
Disable this too inclusive protection for now.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We should explore all possible columns when searching to be
as resilient as possible to changing conditions. This fixes
for example a scenario where even after a sudden creation of
rssi difference between the 2 antennas we would keep doing MIMO
at a low rate instead of switching to SISO at a higher rate using
the better antenna which was the optimal configuration.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Scheduled scan was disabled because it was broken. Now it is
fixed and got disabled by mistake by a merge.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We can now define the priority against BT per AC. This is
possible with a newer firmware that allows to define the
priority with 2 bits.
Note that this change is compatible with older firmware
since older firmware will simply ignore the new bit (11),
and we still set the old bit (12) in the same cases as
before.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This code is really related to BT Coex - move it to the coex
file.
Also - prepare for a FW API change that will happen soon:
Bits 11 and 12 will be allocated for BT priority. Today, we
only have bit 12.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Make bt-coex generic to allow other coex mechanisms.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

7265 features a new calibration which is called antenna
coupling. The purpose of this calibration (which isn't
really a calibration), is to measure the isolation between
the antennas and that can give us useful information for
the Coex modules.

With this information, we can tune the LookUpTables (LUTs)
that define the BT / WiFi contention policy.

The LUTs currently contain dummy values - but they will be
updated soon.

While at it, change the current code to stop duplicate the
host command while sending. This was needed back then, when
the command was short enough to be allocated on the stack.
Since then, the command grew a lot and is now allocated on
the heap - hence we can use the NOCOPY option instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A scheduled scan is a more persistent setting and should take priority
over temporary regular scans. Abort the regular when a sched_scan
request arrives and then request the sched_scan.

The kernel API allows sending a sched_scan without canceling a regular
scan in progress, so this is our way to abstract the FW's limitations.

Make the scan-cancel Rx handler async and flush after invocation to
ensure new scans can't creep in before it.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

cfg80211 assumes a scheduled scan is stopped synchronously. Wait for the
FW before returning to caller.

Don't do anything in the async handler in the stop-from-above flow.
There's no need to call the mac80211 sched-scan completion as the
cleanup will be automatic. Make sure the async handler is called before
the next incoming scan changes the scan_status by flushing the async
handlers after all invocations.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Check for both cfg->d0i3 and fw d0i3 support in order
to enable d0i3 support.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

BGN SKU won't scan on 5.2GHz obviously, but the firmware
still expects the driver to reserve space for the the probe
request for the 5.2GHz band.
Fix this by allocating space and leave it empty.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=69541Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When indicating RF-kill toggle to the higher layer, that
may in turn call back to the transport (for MVM at least)
to turn off the device quickly. Instead of that, allow it
to return whether or not the device should be turned off,
this gets rid of the call indirection and will help make
the API more consistent when we go back to non-threaded
interrupts again for PCIe.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When power update is initiated on BSS STA while P2P client
exists, the power command will be sent only on BSS STA vif
ignoring P2P client.

Since the firmware has symmetric constraints on the power
save enablement we can simplify the code a bit.

The current firmware doesn't know how to enable power
management on P2P client. Even BSS power management must
be disabled when a P2P client is added.

Future firmware will support power save on BSS and P2P client
as long as they are on different channels.
This was buggy since we didn't disable power management on
P2P client interface if BSS added on the same channel.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New firmware enforce valid values for the quota in D3.
The values given to the firmware when suspending and using
WoWLAN where dummy - change them to realistics values.
Tested-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Switch pos to char * which makes the code a bit shorter
as well as other minor cleanups suggested by Joe Perches.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Otherwise lockdep complains about the lock, I'm not sure
why we didn't see this before.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This define is a leftover from dvm (in mvm, it
was replaced by MVM_UCODE_ALIVE_TIMEOUT).
Signed-off-by: NInbal Hacohen <Inbal.Hacohen@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

These values aren't used as the firmware values should be used,
so reading them is pointless and hides potential errors when
somebody uses these values. Leave them zero to make it clearer
that they can't be used. We can't remove the struct members as
the DVM driver does read the values from EEPROM/OTP and the
structure is shared between drivers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Collect statistics regarding rates and aggregations in Rx
frames and export the data via debugfs.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Newer firmware support a new bit in the policy  that allows
to request to apply the time event immediately. Add this bit
without removing the workarounds we used until now to support
older firmares.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to solve races with sched_scan_stop, it is necessary
for the driver to be able to return an error to propagate that
to cfg80211 so it doesn't send an event.
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The new API for ALIVE notification was misunderstood.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

These inlines are pretty pointless now as they just return a
fixed struct value, remove them - the code even gets shorter.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Support the changes below:
- Fields and sections structure were changed.
- the NVM file built from DWord instead of Words.
- sections header format was changed.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New FW enables support for power save on BSS and P2P client MACs
simultaneously when they function on different channels (DCM).
Enable this case in the driver after examining new TLV flag -
IWL_UCODE_TLV_FLAGS_BSS_P2P_PS_DCM. Still power management is not
allowed on both MACs if they function on a same channel.
Remove another redundant TLV flag - IWL_UCODE_TLV_FLAGS_P2P_PS that
is not in use anymore. Remove bound_vif_cnt as redundant.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow reading/writing prph registers.

The address is set in the first argument
of the write operation. second argument
is optional and can be used for writing.

e.g.
echo '0xA01234 0x99' > /sys/kernel/debug/ieee80211/phy0/iwlwifi/iwlmvm/prph_reg
will write 0x99 into reg 0xA01234

cat /sys/kernel/debug/ieee80211/phy0/iwlwifi/iwlmvm/prph_reg
will show its current value (probably 0x99)
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of checking the SKB protocol against EAP, check the
IEEE80211_TX_CTRL_PORT_CTRL_PROTO flag that more generally
indicates whether or not the frame is a port control frame.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This will allow to get sniffer captures with correct
settings for these HT / VHT capabilities.
Also set the corresponding HAVE_MCS / VHT_KNOWN bits in
the registration to mac80211.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There are a number of things in the .data section that should
really be in .rodata, for example all ops structs and strings.
Mark everything const that can be, leaving the .data section
pretty much empty.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Alive notification ver2 support error table information
for 2 CPUs.
This is useful to fetch the error information in case of
firmware assert.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Newer NIC have different memory layout in their SRAM,
so change the checks in iwl_mvm_dump_nic_error_log
accordingly.
Signed-off-by: NAriej Marjieh <ariej.marjieh@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For TSF master/slave synchronization, the FW does not require
exact match in the beacon interval between the master interface
and the slave one, but instead requires that the beacon interval
of one interface is the module of the other.

Modify the tsf_id selection to align with the above.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The d3/d0i3 fw code requires the sta_id to be 0
(this is used to determine the rates and keys
to use in arp offloading).

Reserve sta_id 0 to station interface in order
to comply with this requirement.

Change some functions prototypes in order to
make the allocation function know about
the interface type.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The current WARNING isn't very helpful.
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ieee80211_rx_status.flags is full. Define a new vht_flag
variable to be able to set more VHT related flags and make
room in flags.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath10k]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The scheduled scan matchsets were intended to be a list of filters,
with the found BSS having to pass at least one of them to be passed
to the host. When the RSSI attribute was added, however, this was
broken and currently wpa_supplicant adds that attribute in its own
matchset; however, it doesn't intend that to mean that anything
that passes the RSSI filter should be passed to the host, instead
it wants it to mean that everything needs to also have higher RSSI.

This is semantically problematic because we have a list of filters
like [ SSID1, SSID2, SSID3, RSSI ] with no real indication which
one should be OR'ed and which one AND'ed.

To fix this, move the RSSI filter attribute into each matchset. As
we need to stay backward compatible, treat a matchset with only the
RSSI attribute as a "default RSSI filter" for all other matchsets,
but only if there are other matchsets (an RSSI-only matchset by
itself is still desirable.)

To make driver implementation easier, keep a global min_rssi_thold
for the entire request as well. The only affected driver is ath6kl.

I found this when I looked into the code after Raja Mani submitted
a patch fixing the n_match_sets calculation to disregard the RSSI,
but that patch didn't address the semantic issue.
Reported-by: NRaja Mani <rmani@qti.qualcomm.com>
Acked-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's not a single rate control algorithm actually in
a separate module where the module refcount would be
required. Similarly, there's no specific rate control
module.

Therefore, all the module handling code in rate control
is really just dead code, so remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Change the code to allow making all the rate control ops
const, nothing ever needs to change them. Also change all
drivers to make use of this and mark the ops const.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The main complexity of the power code is that it needs to
take into account the firmware limitations.
These limitations state that we need to have a global
picture of the vifs present in the system to be able to
decide if we can enable power management on a specific vif.

Even device power save (as opposed to vif power management)
must be disabled in certain circumstances (monitor vif).

Refactor the current code to make this clearer by defining
a function that explicitely computes these constraints.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>