Whenever we issue a Set Stall command on EP0,
the state machine will be restarted and Stall
is cleared automatically, when core receives
the next SETUP packet.

There's no need to track that EP0_STALL state.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There are two spots where we wait until the HW finishes processing a
certain command. Initially we had a few problems and we used 500ms as a
limit to be on a the safe side. Paul Zimmerman mentioned this is little too
much. After a debugging session, we noticed that we hardly ever go over 20us
and didn't pass 30usec so far. Using mdelay() seems way overloaded.

Giving the current numbers 500usec as the upper limit is more than  enough.
Should it ever timeout then something is definitely wrong.

While here, also replace the type with u32 since long does not really
fit here.

Cc: Paul Zimmerman <paul.zimmerman@synopsys.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

- since a while we are disabling an endpoint and purging every requests on
  RESET and DISCONNECT which leads to a warning since the endpoint was
  disabled twice (once by the UDC, and second time by the gadget). I
  think UDC should nuke all requests because all those requests
  become invalid. It's gadget driver's responsability, though, to disable
  its used endpoints. This is done by merging dwc3_stop_active_transfer()
  and dwc3_gadget_nuke_reqs() into dwc3_remove_requests().

- dwc3_stop_active_transfer() is now no longer called unconditionaly.
  This has the advantage that it is always called to disable an active
  transfer which means if res_trans_idx 0 than something went wrong and
  it is an error condition because we can't clean up the requests.

- Remove the DWC3_EP_WILL_SHUTDOWN which was introduced while
  introducing the command complete part for dequeue. All requests on
  req_queued list should be removed during the dwc3_cleanup_done_reqs()
  callback so there is no reason to go through the list again.
  We consider it an error condition if requests are still on this
  list since we never queue TRB without LST=1 (the last requests has
  always LST=1, there are no requests with LST=0 behind it).

[ balbi@ti.com : reworked commit log a bit, made patch apply ]
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The DesignWare USB3 core tells us which phase
of a control transfer should be started, it
also tells us which physical endpoint needs
that transfer.

With these two informations, we have all we
need to simply EP0 handling quite a lot and
get rid rid of the SW state machine tracking
ep0 states.

For achieving this perfectly, we needed to
add support for situations where we get
XferNotReady while endpoint is still busy
and XferNotReady while gadget driver still
hasn't queued a request.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This core cannot handle OUT transfers which aren't
aligned to wMaxPacketSize, but that can happen at
least on control endpoint with the USB Audio Class.

This patch adds a bounce buffer to be used on the
case of a non-aligned ep0out request is queued.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

the previous message had too little meaning. Make
it more human readable and use the macro we already
had for extracting the command completion status out
of DEPCMDn register.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

if we don't set DMA address to invalid when unmapping,
we might fall in a situation where request buffer
can't be mapped to DMA again.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Without this patch we won't clear that bit and instead will
clear all other bits on our endpoint flag.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Type 6 should be used for the first transfer during an interval. This is
also what the reference driver is using. Type 7 seems to be for following
or additional transfers within the same interval.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If we collected two requests together (i.e. only the last of them has
LST=1) then we only have to stop transfer once: The clean-up code will
cleanup everything until first TRB with the LST bit set.
After XferComplete this index should be no longer valid since there is
no transfer pending.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

A TRB which is dequeued seems to have its HWO bits set to 1. Therefore
we ignore it if we dequeue it after the command is completed.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size
instead of le16_to_cpu(desc->wMaxPacketSize).
This patch fix it up

Cc: Armin Fuerst <fuerst@in.tum.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Erdfelt <johannes@erdfelt.com>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: David Kubicek <dave@awk.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Brad Hards <bhards@bigpond.net.au>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: David Lopo <dlopo@chipidea.mips.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Xie Xiaobo <X.Xie@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Jiang Bo <tanya.jiang@freescale.com>
Cc: Yuan-hsin Chen <yhchen@faraday-tech.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Herbert Pötzl <herbert@13thfloor.at>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Roman Weissgaerber <weissg@vienna.at>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Florian Floe Echtler <echtler@fs.tum.de>
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Juergen Stuber <starblue@sourceforge.net>
Cc: Georges Toth <g.toth@e-biz.lu>
Cc: Bill Ryder <bryder@sgi.com>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The DesignWare USB3 is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.

Several other parameters can be configured
like amount of FIFO space, amount of TX and
RX endpoints, amount of Host Interrupters,
etc.

The current driver has been validated with
a virtual model of version 1.73a of that core
and with an FPGA burned with version 1.83a
of the DRD core. We have support for PCIe
bus, which is used on FPGA prototyping, and
for the OMAP5, more adaptation (or glue)
layers can be easily added and the driver
is half prepared to handle any possible
configuration the HW engineer has chosen
considering we have the information on
one of the GHWPARAMS registers to do
runtime checking of certain features.

More runtime checks can, and should, be added
in order to make this driver even more flexible
with regards to number of endpoints, FIFO sizes,
transfer types, etc.

While this supports only the device side, for
now, we will add support for Host side (xHCI -
see the updated series Sebastian has sent [1])
and OTG after we have it all stabilized.

[1] http://marc.info/?l=linux-usb&m=131341992020339&w=2Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>