Remove huge board config structure from each instance, read
only necessary fields from flash.

Replace board_type with port_type (1G/10G), there's another
board_type field describing card type (SFP/XFP/CX4).
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAX_RCV_CTX was set to 1, there's only rx context per
PCI function.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o remove unused rx fragment handling code.
o imporove check for status descriptor ownership.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend copyright into 2009 and update address.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For kernel bugzilla #12537:
http://bugzilla.kernel.org/show_bug.cgi?id=12537

Free memory.
Signed-off-by: NDaniel Marjamäki <danielm77@spray.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Bail out if pci_map_single() fails while replenishing rx ring.
o Drop packet if pci_map_{single,page}() fail in tx.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Fix order or rom register writes.
o Reduce udelays when writing rom registers.

This cuts the firmware init time by 40%.

o Do not reset core/memory clocks when reinitializing driver.
  Firmware willl handle this when initialized.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Set restricted (little endian) data types in firmware command
  requests and responses.
o Remove unnecessary conversion to LE when writing registers.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.

Drivers need not do it any more.

Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NX3031 does not require driver to kill dma watchdog.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

For NX3031, multicast filtering, promisc mode, and max frame size
setting is handled by firmware, driver needs to send request to
enable/disable it.

For old chip revisions / firmware, driver still sets it directly.

Added function pointer to set mtu according to chip revision.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

NX3031 supports cut-through operation where ingress packets are
directly dma'ed into host buffers to reduce latency.

This requires larger dma buffers (2kb) and different alignemnt.

The buffer posting logic is changed a bit. The free rx buffers
are maintained in linked list, since the received reference
handles can be out of order. However rx descriptors are still
posted sequentially, indexed by producer.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

MAC addr, multicast filters, mtu are set through firmware commands
in firmware v4.0.0+ because of virtualization of physical ports.
Link status is also read from registers allocated by firmware for
each virtual port.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Contains rx and tx ring context management and certain
firmware commands for netxen firmware v4.0.0+.

This patch gathers all HW context management code into
netxen_nic_ctx.c.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

It had only couple of functions which are moved to main.c
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add initialization code in pci probe for new chip and retain
compatibility with old revisions.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

New revision of netxen chip has 2MB PCI memory. Older chips
had 128MB addressable PCI memory. To retain compatibility,
this patch adds function pointers based on pci bar0 size.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add macros for new chip revision and board configurations.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Enable multicast address filtering capabilities in the hardware.
Upto 16 multicast addresses can be programmed for each physical
port. Support "allmulti" mode, if enabled.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

o Reduce access to global arrays in data path.
o Remove duplicate/unused variables, unecessary alignment constraints.
o Use correct pci_dev instead of fallback device for consistent
  allocations.
o Disable ethtool set_eeprom functionality for now, it was only used
  for flashing firmware.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Downloading firmware in pci probe allows recovery in case of
firmware failure by reloading the driver.

Also reduced delays in firmware load.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

o Remove unnecessary debug prints and functions.
o Explicitly specify pci class (0x020000) to avoid enabling
  management function.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Don't count rx dropped packets based on return value of netif_receive_skb(),
which is misleading.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Tested-by: NVernon Mauery <mauery@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

o eliminate tx lock in netxen adapter struct, instead pound on netdev
  tx lock appropriately.
o remove old "concurrent transmit" code that unnecessarily drops and
  reacquires tx lock in hard_xmit_frame(), this is already serialized
  the netdev xmit lock.
o reduce scope of tx lock in tx cleanup. tx cleanup operates on
  different section of the ring than transmitting cpus and is
  guarded by producer and consumer indices. This fixes a race
  caused by rx softirq preemption on realtime kernels.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Tested-by: NVernon Mauery <mauery@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

o separate and simpler irq handler for msi interrupts, avoids few checks
  than legacy mode.
o avoid redudant tx_has_work() and rx_has_work() checks in interrupt
  and napi, which can uncork irq based on racy (lockless) access to tx
  and rx ring indices. If we get interrupt, there's sufficient reason to
  schedule napi.
o replenish rx ring more often, remove self-imposed threshold rcv_free
  that prevents posting rx desc to card. This improves performance in
  low memory.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Tested-by: NVernon Mauery <mauery@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Recent netxen firmware has new scheme of generating MSI interrupts, it
raises interrupt and blocks itself, waiting for driver to unmask. This
reduces chance of spurious interrupts.

The driver will be able to deal with older firmware as well.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Tested-by: NVernon Mauery <mauery@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch contains the following cleanups:
- static functions in .c files shouldn't be marked inline
- make needlessly global code static
- #if 0 unused code
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Here's the reworked patch.

This cleans up some unnecessary byte-swapping while setting up tx and
interpreting rx desc. The 64 bit rx status data should be converted
to host endian format only once and the macros just need to extract
bitfields.

This saves a spate of interrupts on pseries blades caused by buggy
(non) processing rx status ring.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

netxen driver allows limited number of threads simultaneously posting
skb's in tx ring. If transmit slot is unavailable, driver calls
schedule() or loops in xmit_frame().

This patch returns TX_BUSY and lets the stack reschedule the packet if
transmit slot is unavailable. Also removes unnecessary check for tx
timeout in the driver itself, the network stack does that anyway.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Resubmitting the patch.

This patch improves ethtool support for printing correct ring statistics,
segmentation offload status, etc.

Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Resending patch 3/3 only.

These changes allow driver close routine to be called during module unload,
to clean-up buffers and other software resources, flush queues etc. Also,
hardware is reset to pristine state.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NMilan Bag <mbag@netxen.com>
Signed-off-by: NWen Xiong <wenxiong@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch updates the various access routines to access different
control and status settings present in different register locations.
This will fix problems related to working of different ports in
multi Port card.

Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NetXen: Fix incorrect link status even with switch turned OFF.
NetXen driver failed to accurately indicate when a link is up or down.
This was encountered during failover testing, when the first port
indicated that the link was up even when the 10G switch it was assigned
to in the Bladecenter was turned off completely.

Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NetXen: Add NETXEN prefixes to macros to clean them up.
This is a cleanup patch which adds NETXEN prefix to some stand
alone macro names.
These posed compile errors when NetXen driver was backported to 2.6.9
on PPC architecture as macros like USER_START are defined in file
arch/ppc64/mm/hash_utils.c
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Acked-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>