Avoid flashing BE3 UFI on BE3-R chip by verifying asic_revision
number of the chip.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't log "Out of MCCQ wrbs" msg. When the driver doesn't receive any
response from the FW it already logs a "FW not responding" message.
The driver runs out of MCCQ wrbs much later. Also, this message can
swamp the kernel log in HW/FW error scenarios.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Skyhawk-R and BE3-R (SuperNIC profile) require V2 version
of TXQ_CREATE cmd to be used.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

a. Common tree of `dir` structures.
b. Multi-port devices structures.

CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

introduce a procedure to read in u32 granularity.

CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/s390/net/qeth_l3_main.c: In function 'qeth_l3_add_vlan_mc':
>> drivers/s390/net/qeth_l3_main.c:1662:3: error: too few arguments to function '__vlan_find_dev_deep'
   include/linux/if_vlan.h:88:27: note: declared here
   drivers/s390/net/qeth_l3_main.c: In function 'qeth_l3_add_vlan_mc6':
>> drivers/s390/net/qeth_l3_main.c:1723:3: error: too few arguments to function '__vlan_find_dev_deep'
   include/linux/if_vlan.h:88:27: note: declared here
   drivers/s390/net/qeth_l3_main.c: In function 'qeth_l3_free_vlan_addresses4':
>> drivers/s390/net/qeth_l3_main.c:1767:2: error: too few arguments to function '__vlan_find_dev_deep'
   include/linux/if_vlan.h:88:27: note: declared here
   drivers/s390/net/qeth_l3_main.c: In function 'qeth_l3_free_vlan_addresses6':
>> drivers/s390/net/qeth_l3_main.c:1797:2: error: too few arguments to function '__vlan_find_dev_deep'
   include/linux/if_vlan.h:88:27: note: declared here
   drivers/s390/net/qeth_l3_main.c: In function 'qeth_l3_process_inbound_buffer':
>> drivers/s390/net/qeth_l3_main.c:1980:6: error: too few arguments to function '__vlan_hwaccel_put_tag'
   include/linux/if_vlan.h:234:31: note: declared here
   drivers/s390/net/qeth_l3_main.c: In function 'qeth_l3_verify_vlan_dev':
>> drivers/s390/net/qeth_l3_main.c:2089:3: error: too few arguments to function '__vlan_find_dev_deep'
   include/linux/if_vlan.h:88:27: note: declared here
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing return statement for CONFIG_BUG=n.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix up some function signatures for CONFIG_VLAN=n that were missed during
the 802.1ad support patches.

Found by the kbuild robot.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following leak is reported by kmemleak:

[   86.812073] kmemleak: Found object by alias at 0xffff88006ecc76f0
[   86.816019] Pid: 739, comm: kworker/u:1 Not tainted 3.9.0-rc5+ #842
[   86.816019] Call Trace:
[   86.816019]  <IRQ>  [<ffffffff81151c58>] find_and_get_object+0x8c/0xdf
[   86.816019]  [<ffffffff8190e90d>] ? vlan_info_rcu_free+0x33/0x49
[   86.816019]  [<ffffffff81151cbe>] delete_object_full+0x13/0x2f
[   86.816019]  [<ffffffff8194bbb6>] kmemleak_free+0x26/0x45
[   86.816019]  [<ffffffff8113e8c7>] slab_free_hook+0x1e/0x7b
[   86.816019]  [<ffffffff81141c05>] kfree+0xce/0x14b
[   86.816019]  [<ffffffff8190e90d>] vlan_info_rcu_free+0x33/0x49
[   86.816019]  [<ffffffff810d0b0b>] rcu_do_batch+0x261/0x4e7

The reason is that in vlan_info_rcu_free() we don't take the VLAN protocol
into account when iterating over the vlan_devices_array.
Reported-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Tested-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following patchset contains a small batch of Netfilter
updates for your net-next tree, they are:

* Three patches that provide more accurate error reporting to
  user-space, instead of -EPERM, in IPv4/IPv6 netfilter re-routing
  code and NAT, from Patrick McHardy.

* Update copyright statements in Netfilter filters of
  Patrick McHardy, from himself.

* Add Kconfig dependency on the raw/mangle tables to the
  rpfilter, from Florian Westphal.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the get_settings ethtool op to the bonding
driver.  This was motivated by users who wanted to get the speed of the
bond and compare that against throughput to understand utilization.
The behavior before this patch was added was problematic when computing
line utilization after trying to get link-speed and throughput via SNMP.

Output from ethtool looks like this for a round-robin bond:

Settings for bond0:
	Supported ports: [ ]
	Supported link modes:   Not reported
	Supported pause frame use: No
	Supports auto-negotiation: No
	Advertised link modes:  Not reported
	Advertised pause frame use: No
	Advertised auto-negotiation: No
	Speed: 11000Mb/s
	Duplex: Full
	Port: Other
	PHYAD: 0
	Transceiver: internal
	Auto-negotiation: off
	MDI-X: Unknown
	Link detected: yes

I tested this and verified it works as expected.  A test was also done
on a version backported to an older kernel and it worked well there.

v2: Switch to using ethtool_cmd_speed_set to set speed, added check to
SLAVE_IS_OK for each slave in bond, dropped mode-specific calculations
as they were not needed, and set port type to 'Other.'

v3: Fix useless assignment and checkpatch warning.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces a small, internal helper function, that is used by
PF_PACKET. Based on the flags that are passed, it extracts the packet
timestamp in the receive path. This is merely a refactoring to remove
some duplicate code in tpacket_rcv(), to make it more readable, and to
enable others to use this function in PF_PACKET as well, e.g. for TX.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, ktime2ts is a small helper function that is only used in
net/socket.c. Move this helper into the ktime API as a small inline
function, so that i) it's maintained together with ktime routines,
and ii) also other files can make use of it. The function is named
ktime_to_timespec_cond() and placed into the generic part of ktime,
since we internally make use of ktime_to_timespec(). ktime_to_timespec()
itself does not check the ktime variable for zero, hence, we name
this function ktime_to_timespec_cond() for only a conditional
conversion, and adapt its users to it.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noticed by Ben Hutchings.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rajesh Borundia says:

====================
* "qlcnic: Change 82xx adapter VLAN id endian type".
  - Adapter requires VLAN id in little endian. VLAN id was being
    converted to __le16 and then passed as a parameter. Pass VLAN id
    as u16 and then use cpu_to_le16 at appropriate places. It is
    appropriate for net-next as SR-IOV patches have a dependency on it.
* "qlcnic: Fix loopback test for SR-IOV PF".
  - It is appropriate for net-next as change is needed for SRIOV PF
    only.
* Remaining patches add enhancements to SR-IOV functionality like
  - FLR handling
  - Adapter reset recovery handling
  - iproute2 tool support for configuring MAC address, Tx rate and
    VLAN id.
  - Mailbox polling support for SR-IOV PF in case mailbox interrupts
    are disabled.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o When mailbox interrupt is disabled PF should be
  able to process request from VF. Enable polling
  for such cases.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Do not disable mailbox interrupts while running
  loopback test through SR-IOV PF.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Add support for VLAN id configuration per VF using
  iproute2 tool.
o VLAN id's 1-4094 are treated as PVID by the PF and
  Guest VLAN tagging is not allowed by default.
o PVID is disabled when the VLAN id is set to 0
o Guest VLAN tagging is allowed when the VLAN id is set to 4095.
o Only one Guest VLAN id  is supported.
o VLAN id can be changed only when the VF driver is not loaded.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Add support for MAC address and Tx rate configuration
  per VF via iproute2 tool.
o Tx rate change is allowed while the guest is running
  and the VF driver is loaded.
o MAC address change is allowed only when VF driver
  is not loaded.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Implement recovery mechanism for VF to recover from
  adapter resets.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o FLR from Hypervisor - When hypervisor issues a VF FLR request,
  adapter notifies the parent PF driver of the FLR request for PF
  driver to perform any cleanup on behalf of that VF.
o FLR from VF Driver - VF driver may initiate a VF FLR request,
  if VF state needs to be cleaned up before a re-initialization.
  VF re-initialization during kdump is an example.
o PF driver cleans up all resources allocated on behalf of a  VF,
  on VF FLR notifications from the adapter or from the VF driver.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o 82xx adapter requires VLAN id in little endian format.
  Instead of passing vlan id parameter as __le16, pass the
  parameter as u16 and  use cpu_to_le16 at appropriate places.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Patrick McHardy says:

====================
The following patches contain an implementation of memory mapped I/O for
netlink. The implementation is modelled after AF_PACKET memory mapped I/O
with a few differences:

- In order to perform memory mapped I/O to userspace, the kernel allocates
  skbs with the data area pointing to the data area of the mapped frames.
  All netlink subsystems assume a linear data area, so for the sake of
  simplicity, the mapped data area is not attached to the paged area but
  to skb->data. This requires introduction of a special skb alloction
  function that just allocates an skb head without the data area. Since this
  is a quite rare use case, I introduced a new function based on __alloc_skb
  instead of splitting it up into head and data alloction. The alternative
  would be to   introduce an __alloc_skb_head and __alloc_skb_data function,
  which would actually be useful for a specific error case in memory mapped
  netlink, but would require a couple of extra instructions for the common
  skb allocation case, so it doesn't really seem worth it.

  In order to get the destination memory area for skb->data before message
  construction, memory mapped netlink I/O needs to look up the destination
  socket during allocation instead of during transmission because the
  ring is owned by the receiveing socket/process. A special skb allocation
  function (netlink_alloc_skb) taking the destination pid as an argument is
  used for this, all subsystems that want to support memory mapped I/O need
  to use this function, automatic fallback to the receive queue happens
  for unconverted subsystems. Dumps automatically use memory mapped I/O if
  the receiving socket has enabled it.

  The visible effect of looking up the destination socket during allocation
  instead of transmission is that message ordering in userspace might
  change in case allocation and transmission aren't performed atomically.
  This usually doesn't matter since most subsystems have a BKL-like lock
  like the rtnl mutex, to my knowledge the currently only existing case
  where it might matter is nfnetlink_queue combined with the recently
  introduced batched verdicts, but a) that subsystem already includes
  sequence numbers which allow userspace to reorder messages in case it
  cares to, also the reodering window is quite small and b) with memory
  mapped transmission batching can be performed in a subsystem indepandant
  manner.

- AF_NETLINK contains flow control for database dumps, with regular I/O
  dump continuation are triggered based on the sockets receive queue space
  and by recvmsg() calls. Since with memory mapped I/O there are no
  recvmsg() calls under normal operation, this is done in netlink_poll(),
  under the assumption that userspace has processed all pending frames
  before invoking poll(), thus the ring is expected to have room for new
  messages. Dumps currently don't benefit as much as they could from
  memory mapped I/O because each single continuation requires a poll()
  call. A more agressive approach seems like a good idea to me, especially
  in case the socket is not subscribed to any multicast groups (IOW only
  receiving explicitly requested data).

Besides that, the memory mapped netlink implementation extends the states
defined by AF_PACKET between userspace and the kernel by a SKIP status, this
is intended for the case that userspace wants to queue frames (specifically
when using nfnetlink_queue, an IDS and stream reassembly, requested by
Eric Leblond) for a longer period of time. The kernel skips over all frames
marked with SKIP when looking or unused frames and only fails when not finding
a free frame or when having skipped the entire ring.

Also noteworthy is memory mapped sendmsg: the kernel performs validation
of messages before accepting and processing them, in order to prevent
userspace from changing the messages contents after validation, the
kernel checks that the ring is only mapped once and the file descriptor
is not shared (in order to avoid having userspace set up another mapping
after the first mentioned check). If either of both is not true, the
message copied to an allocated skb and processed as with regular I/O.
I'd especially appreciate review of this part since I'm not really versed
in memory, file and process management,

The remaining interesting details are included in the changelogs of the
individual patches and the documentation, so I won't repeat them here.

As an example, nfnetlink_queue is convererted to support memory mapped
I/O. Other subsystems that would probably benefit are nfnetlink_log,
audit and maybe ISCSI, not sure.

Following are some numbers collected by Florian Westphal based on a
slightly older version, which included an experimental patch for the
nfnetlink_queue ordering issue.

===

Test hardware is a 12-core machine
Intel(R) Xeon(R) CPU E5-2620 0 @ 2.00GHz
ixgbe interfaces are used (i.e., multiqueue nics).
irqs are distributed across the cpus.

I've made several tests.

The simple one consists of 3GBit UDP traffic, packets are 1500 bytes
in size (i.e., no fragmentation), with a single nfqueue
and the test client programs in libmnl examples directory.
Packets are sent from one /24 net to another /24 net, i.e.
there are a few hundred flows active at any given time.

I've also tested with snort, but I disabled all rules.
6Gbit UDP traffic is generated in the snort case, and
6 nfqueues are used (i.e., 6 snorts run in parallel).

I've tested with 3 different kernels, all based on 3.7.1.
- 3.7.1, without the mmap patches
- 3.7.1, with Patricks mmap patches
- 3.7.1, with mmap patches and extended spinlock to ensure packet ids are
  monotonically increasing and cannot be re-ordered.  This is what we
  currently ship in our product.

  [ the spinlock that is extended is the per nfqueue spinlock, it will
    be held from the time the netlink skb is allocated until the netlink
    skb is sent to userspace:

    http://1984.lsi.us.es/git/nf-next/commit/?h=mmap-netlink3&id=b8eb19c46650fef4e9e4fe53f367f99bbf72afc9
  ]

snort is normally used in "batch mode", i.e., after processing 25 packets
a single "batch verdict" is sent to accept the packets seen so far.
"mmap snort" means RX_RING + sendmsg(), i.e. TX_RING is not used at this
time (except where noted below).

One reason is that snort has a reload thread, so kernel needs to copy;
also in the snort case no payload rewrite takes place, so compared
to the rx path the tx path is cheap.

Results:

3.7.1, without mmap patches, i.e. recv()+sendmsg() for everyone
nfq-queue:           1.7 gbit out
snort-recv-batch-25  5.1 gbit out
snort-recv-no-batch  3.1 gbit out

3.7.1 + mmap + without extended spinlocked section
nfq-queue:           1.7 gbit out (recv/sendmsg)
nfq-queue-mmap:      2.4 gbit out
snort-mmap-batch-25	 5.6 gbit out  (warning: since ids can be
                                        re-ordered, this version is "broken").
snort-recv-batch-25	 5.1 gbit out
snort-mmap-no-batch	 4.6 gbit out (i.e., one verdict per packet)

Kernel 3.7.1 + mmap + extended spinlock section:
nfq-queue:	1.4 gbit out
nfq-queue-mmap: 2.3 gbit out
snort:          5.6 gbit out

Conclusions:
- The "extended spinlocked section" hurts performance in the
  single queue case; with 6 snorts there is no measureable slowdown.
- I tried to re-write the mmap-snort to work without batch verdicts, but
  results were not very encouraging:

kernel 3.7.1 + mmap (without extended spinlocked section):

snort-mmap-batch-25      5.6 gbit out (what we currenlty ship)
snort-recv-batch-25      5.1 gbit out (without using mmap)
snort-mmap-batch-1       4.6 gbit out (with mmap but without batch verdicts)
snort-mmap-txring-25     5.2 gbit out (with mmap but without batch verdicts)
snort-mmap-txring-1      4.6 gbit out (with mmap but without batch verdicts)

The difference between the last two is that in the txring-25 case, we
put a verdict into the tx ring after every packet, but will only
invoke sendmsg(, NULL, 0) after processing 25 packets.  So the only
difference is the number of sendmsg calls/context switches.

So, i.o.w, kernel 3.7.1 + mmap + the extra locking crap is faster
than 3.7.1 + mmap-without-extra-locking and single-verdict-per packet.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of the confusing mix of pid and portid and use portid consistently
for all netlink related socket identities.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on AF_PACKET.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add flow control for memory mapped RX. Since user-space usually doesn't
invoke recvmsg() when using memory mapped I/O, flow control is performed
in netlink_poll(). Dumps are allowed to continue if at least half of the
ring frames are unused.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for mmap'ed recvmsg(). To allow the kernel to construct messages
into the mapped area, a dataless skb is allocated and the data pointer is
set to point into the ring frame. This means frames will be delivered to
userspace in order of allocation instead of order of transmission. This
usually doesn't matter since the order is either not determinable by
userspace or message creation/transmission is serialized. The only case
where this can have a visible difference is nfnetlink_queue. Userspace
can't assume mmap'ed messages have ordered IDs anymore and needs to check
this if using batched verdicts.

For non-mapped sockets, nothing changes.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for mmap'ed sendmsg() to netlink. Since the kernel validates
received messages before processing them, the code makes sure userspace
can't modify the message contents after invoking sendmsg(). To do that
only a single mapping of the TX ring is allowed to exist and the socket
must not be shared. If either of these two conditions does not hold, it
falls back to copying.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add helper functions for looking up mmap'ed frame headers, reading and
writing their status, allocating skbs with mmap'ed data areas and a poll
function.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for mmap'ed RX and TX ring setup and teardown based on the
af_packet.c code. The following patches will use this to add the real
mmap'ed receive and transmit functionality.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For mmap'ed I/O a netlink specific skb destructor needs to be invoked
after the final kfree_skb() to clean up state. This doesn't work currently
since the skb's ownership is transfered to the receiving socket using
skb_set_owner_r(), which orphans the skb, thereby invoking the destructor
prematurely.

Since netlink doesn't account skbs to the originating socket, there's no
need to orphan the skb. Add a netlink specific skb_set_owner_r() variant
that does not orphan the skb and use a netlink specific destructor to
call sock_rfree().
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Netlink doesn't account skbs to the sending socket, so the there's no
need to orphan the skb before trimming it.

Removing the skb_orphan() call is required for mmap'ed netlink, which uses
a netlink specific skb destructor that must not be invoked before the
final freeing of the skb.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>