Whenever the LID is set, notify the HCA specific code so that the
appropriate HW registers can be updated. Also log the info on the
console at low priority.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch adds code to enable/disable the IBTA 1.2 heartbeat for testing
if the HCA supports it.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The hardware-based recovery doesn't need any intervention, and in a few
cases we can get a bit confused about state and skip steps such as
turning off the link state LED when we consider recovery to be "down".
So ignore this transition, and either we recover in hardware, or we
transition to down, and will handle it then.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Newer HCAs have a HW option to write a sequence number to each receive
queue entry and avoid a separate DMA of the tail register to memory.
This patch adds support for these changes.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch makes some white space changes and minor non-functional
changes to more closely match the code in OFED-1.3.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch checks for old and new format writes to send a packet via the
diagnostic interface.
Signed-off-by: NMichael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Raw comparison against jiffies will fail if jiffies wraps, although
since ipath currently only supports 64-bit architectures, this is rather
far-fetched.  Still, it's better to use time_after_eq().
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a create_flags member to struct ib_qp_init_attr that will allow a
kernel verbs consumer to create a pass special flags when creating a QP.
Add a flag value for telling low-level drivers that a QP will be used
for IPoIB UD LSO.  The create_flags member will also be useful for XRC
and ehca low-latency QP support.

Since no create_flags handling is implemented yet, add code to all
low-level drivers to return -EINVAL if create_flags is non-zero.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for reading newer card's EEPROMs while continuing to support
older EEPROMs.

Also, add support for the temperature sensor if present.
Signed-off-by: NMichael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This reduces the latency for RC ACKs when a PIO buffer is available.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

A fixed partitioning of send buffers is determined at driver load time
for user processes and kernel use.  Since send buffers are a scarce
resource, it makes sense to allow the kernel to use the buffers if they
are not in use by a user process.

Also, eliminate code duplication for ipath_force_pio_avail_update().
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The link can be put in LINKDOWN_DISABLE state either locally or via a
MAD.  However, the link-recovery code will take it out of that state as
a side-effect of attempts to clear SerDes/XGXS issues.

We add a flag to indicate "link is down on purpose, leave it alone."
Signed-off-by: NMichael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Update the module author to the current email address.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In slave_or_pri_blk(), pci_write_config_byte() is used to write a
16-bit quantity to clear linkctrl CRC error bits.  This is clearly a
bug and also causes the warning

    drivers/infiniband/hw/ipath/ipath_iba6110.c: In function 'slave_or_pri_blk':
    drivers/infiniband/hw/ipath/ipath_iba6110.c:849: warning: overflow in implicit constant conversion

Fix this by using pci_write_config_word() instead.
Acked-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The receive queue number of WRs and SGEs shouldn't be checked if a
SRQ is specified.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove useless comment about list removal since locks are held and
the code checks that the QP is on the list before removing it.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Workaround a QLE7140 problem that in rare cases causes flow control
problems after link recovery by forcing a link retrain after recovery.
A module parameter is provided to control the behavior in case it causes
problems.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch adds code to get/set portinfo to support multiple link speeds
and widths.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There's a conflict between our need to quiesce PSM-based applications
to avoid HoL blocking when the IB link goes down and the apps' desire
to remain running so that their quiescence timout mechanism can keep
running.

The compromise is to STOP the processes for a fixed period of time and
then alternate between CONT and STOP until the link is again active.

If there are poor interactions with subnet manager configuration at a
given site, the interval can be adjusted via a module paramter.
Signed-off-by: NJohn Gregor <john.gregor@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Don't try to handle freeze mode HW errors if the driver is in diagnostic
mode since some tests can cause errors that shouldn't be processed.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The check for link up was incorrect, thus setting the LED display
inconsistently with the link state.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The error recovery code for updating the driver's cached status information
for which send buffers are busy or free wasn't updated for IBA7220.
It should be similar to the initialization code in enable_chip().
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix byte order of value assigned to pioavailshadow.  This bug was
detected by sparse endianness warnings.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Enable use of 4KB MTU.  Since the driver uses more pinned memory for
receive buffers when the 4KB MTU is enabled, whether or not the fabric
supports that MTU, add a "mtu4096" module parameter that can be used to
limit the MTU to 2KB when it is known that 4KB MTUs can't be used
anyway.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The code was checking if units are present, but not that present units
were usable (link up, etc.)
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Modern I/O buses like PCIe and HT can be configured for multiple speeds
and widths.  When an ipath HCA seems to have lower than expected
performance, it is very useful to be able to display what the driver
thinks the bus speed is.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch makes some constants chip-specific, and makes some related
changes to prepare for supporting another HCA.

Signed-off-by: Dave Olson <dave.olson@qlogic.com
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Recent sparse versions and kernel cleanups knock down the false positive
rate of the ipath driver code to a point where having it be sparse clean
is worthwhile. Here we fixup the sparse warnings.  Some of these warnings
(and the impetus to run sparse again) are due to work by Roland Dreier.
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix

    drivers/infiniband/hw/ipath/ipath_init_chip.c:526:10: warning: symbol 'val' shadows an earlier one
    drivers/infiniband/hw/ipath/ipath_init_chip.c:473:6: originally declared here

by giving the second val a different name.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NArthur Jones <arthur.jones@qlogic.com>

There's no reason for the third parameter of ipath_count_units() to be
a u32 *, so change it to be an int * instead.  This fixes the sparse
warning:

    drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47: warning: incorrect type in argument 3 (different signedness)
    drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47:    expected unsigned int [usertype] *maxportsp
    drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47:    got int *<noident>
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Reset the retry counter when we get a good RDMA_READ_RESPONSE_MIDDLE
packet.  This fix will prevent the requester from reporting a retry
exceeded error too early.
Signed-off-by: NPatrick Marchand Latifi <patrick.latifi@qlogic.com>

A work completion entry could be placed on the wrong completion
queue when an RC QP is placed in the error state.
Signed-off-by: NPatrick Marchand Latifi <patrick.latifi@qlogic.com>
Acked-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch fixes the initialization of RC QPs, since we would rely on
the queue pair type (ibqp->qp_type) being set, but this field is only
initialized when we return from ipath_create_qp (it is initialized by
the user-level verbs library).

The fix is to not depend on this field to initialize the send and
the receive state of the RC QP.
Signed-off-by: NPatrick Marchand Latifi <patrick.latifi@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There can be a case where the requester's rnr retry counter
(s_rnr_retry) is less than the number of rnr retries allowed per QP
(s_rnr_retry_cnt).  This can happen if the s_rnr_retry counter is being
decremented and an ipath_query_qp call is issued during that time frame.
The fix is to always return the number of rnr retries allowed per QP
instead of the requester's rnr counter.

Found by code review.
Signed-off-by: NPatrick Marchand Latifi <patrick.latifi@qlogic.com>
Acked-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Subnet manager SetPortinfo messages distingush between changing the link
state (DOWN, ARM, ACTIVE) and the link physical state (POLL, SLEEP,
DISABLED).  These are somewhat independent commands and affect when link
width and speed changes take effect.  Without this patch, a link DOWN
physical state NOP command was causing the link width and speed settings
to take effect which should only happen when the link physical state is
goes down (either by a SMP or some link physical error like link errors
exceeding the threshold).
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Move the increment of s_hdrwords into the existing if block that tests 
if we're doing a send with immediate, to save one test of the opcode.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add new mappings from port physical state (a HW register value) to the
IB SubnGet(PortInfo) port physical state.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>