Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch changes the interrupt enable sequence for the sunzilog driver 
so that interrupts are not enabled untill after the interrupt handler has 
been installed. If this is not done, some SS1 and SS2 sun4c systems panic 
on un-handled interrupt before the handler gets installed preventing boot.

It also adds in support for the ESCC version of the zilog chips. The
changes mean that the FIFO will be enabled for ESCC versions of the
SCC UART. My interpretation of the SCC manual and the existing interrupt
handler code is that it sould be able to make good use of the FIFO without
issues.
Signed-off-by: NMark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make x86 COM ports into platform devices and don't probe for them
if we have PNP.

This prevents double discovery, where a device was found both by
the legacy probe and by 8250_pnp, e.g.,

    serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A

This also means IRDA devices without a UART PNP ID will no longer be
claimed by the serial driver, which might require changes in IRDA
drivers and administration.

In addition to this patch, you may need to configure a setserial init
script, e.g., /etc/init.d/setserial, so it doesn't poke legacy UART
stuff back in.  On Debian, "dpkg-reconfigure setserial" with the "kernel"
option does this.

To force the old legacy probe behavior even when we have PNPBIOS or
ACPI, load the new legacy_serial module (or build 8250 static) with
the "legacy_serial.force" option.

[akpm@linux-foundation.org: fix makefiles]
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Keith Owens <kaos@ocs.com.au>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Russell King <rmk+serial@arm.linux.org.uk>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove some obviously old interrupt disable/enable code that has been
commented out.
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The serial_txx9 driver have abused device numbers (major 4, minor 128) if
CONFIG_SERIAL_TXX9_STDSERIAL was not set.  This patch makes the driver use
proper device numbers assigned for it (major 204, minor 196-203).  I
suppose a typical user of this driver set CONFIG_SERIAL_TXX9_STDSERIAL to Y
(i.e.  use "ttyS0"), so this patch would not cause big compatibility issue.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SPIN_LOCK_UNLOCKED cleanup,use __SPIN_LOCK_UNLOCKED instead
Signed-off-by: NMilind Arun Choudhary <milindchoudhary@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.

Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The jsm driver doesn't currently use the uart_handle_*_change helper
functions, which are the obvious place for things like linuxpps to tie
into (which it now does of course), and as a result the jsm driver can
not be used with linuxpps and anything else that ties into the
serial_core helper functions.  This patch adds calls to these helper
functions whenever the value they manage changes.  That actual storage
of the state is not modified since the jsm driver caches the current
settings (The 8250 driver reads them everytime a user asks for the
state), and only updates them whenever they change.
Signed-off-by: NLen Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Scott H Kilau <Scott_Kilau@digi.com>
Cc: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The jsm driver fails when you try to use the TIOCSSERIAL ioctl.  The reason
is that the driver never sets uart_port.uartclk, causing the data received
using TIOCGSERIAL to not match the internal state of the driver.  This
patch fixes this problem by settings the uartclk to the value used by the
serial_core (16 times the baud base).
Signed-off-by: NLen Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Scott H Kilau <Scott_Kilau@digi.com>
Cc: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch implements the driver necessary use the Analog Devices Blackfin
processor's Serial Port.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

serial_core, use pr_debug
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The MPSC serial driver assumes that interrupt is always on to pick up the
DMA transmit ops that aren't submitted while the DMA engine is active.
However when irqs are off for a period of time such as operations under
kernel crash dump console messages do not show up due to additional DMA ops
are being dropped.  This makes console writes to process through all the tx
DMAs queued up before submitting a new request.

Also, the current locking mechanism does not protect the hardware registers
and ring buffer when a printk is done during the serial write operations.
The additional per port transmit lock provides a finer granular locking and
protects registers being clobbered while printks are nested within UART
writes.
Signed-off-by: NDave Jiang <djiang@mvista.com>
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

At present, the serial core always allows setserial in userspace to change the
port address, irq and base clock of any serial port.  That makes sense for
legacy ISA ports, but not for (say) embedded ns16550 compatible serial ports
at peculiar addresses.  In these cases, the kernel code configuring the ports
must know exactly where they are, and their clocking arrangements (which can
be unusual on embedded boards).  It doesn't make sense for userspace to change
these settings.

Therefore, this patch defines a UPF_FIXED_PORT flag for the uart_port
structure.  If this flag is set when the serial port is configured, any
attempts to alter the port's type, io address, irq or base clock with
setserial are ignored.

In addition this patch uses the new flag for on-chip serial ports probed in
arch/powerpc/kernel/legacy_serial.c, and for other hard-wired serial ports
probed by drivers/serial/of_serial.c.
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the integrated serial ports of the MIPS RM9122 processor
and its relatives.

The patch also does some whitespace cleanup.

[akpm@linux-foundation.org: cleanups]
Signed-off-by: NThomas Koeller <thomas.koeller@baslerweb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Serial driver patch for the PMC-Sierra MSP71xx devices.

There are three different fixes:

1 Fix for DesignWare APB THRE errata: In brief, this is a non-standard
  16550 in that the THRE interrupt will not re-assert itself simply by
  disabling and re-enabling the THRI bit in the IER, it is only re-enabled
  if a character is actually sent out.

  It appears that the "8250-uart-backup-timer.patch" in the "mm" tree
  also fixes it so we have dropped our initial workaround.  This patch now
  needs to be applied on top of that "mm" patch.

2 Fix for Busy Detect on LCR write: The DesignWare APB UART has a feature
  which causes a new Busy Detect interrupt to be generated if it's busy
  when the LCR is written.  This fix saves the value of the LCR and
  rewrites it after clearing the interrupt.

3 Workaround for interrupt/data concurrency issue: The SoC needs to
  ensure that writes that can cause interrupts to be cleared reach the UART
  before returning from the ISR.  This fix reads a non-destructive register
  on the UART so the read transaction completion ensures the previously
  queued write transaction has also completed.
Signed-off-by: NMarc St-Jean <Marc_St-Jean@pmc-sierra.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the serial port gets shut down, then console output stalls.  9 out
of 10 kernel hackers agree, this is a bad thing.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NSylvain Munaut <tnt@246tNt.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

for consistency with other Open Firmware interfaces (and Sparc).

This is just a straight replacement.

This leaves the compatibility define in place.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Mark sunsu_console_setup() as __init and rename 'sunsu_cons'
to 'sunsu_console' so that it matches modpost.c's whitelist.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds the enable/disable hooks for the port clock to sh-sci.
Signed-off-by: Ndmitry pervushin <dimka@nomadgs.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Support the SH7712 (SH3-DSP) Solution Engine reference board.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

With the GDB stub being entered via a special sysrq trigger,
we don't want to hit it directly from sci_br_interrupt().
Without this, there is access to the other sysrq triggers when
kgdb is enabled.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds preliminary support for the SH7785-based Highlander board.
Some of the Highlander support code is reordered so that most of it
can be reused directly.

This also plugs in missing SH7785 checks in the places that need it,
as this is the first board to support the CPU.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This code has suffered quite a bit of bitrot, do some basic
tidying to get it to a reasonably functional state again.
This gets the basic support and the console working again.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch moves the i.MX UART register descriptions from
include/asm-arm/arch-imx/imx-regs.h to the serial driver itself.
This helps using the driver on other architectures like mx31
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Allow slower serial baud-rates by switching the UART clock from MCK to
MCK/8.

Based on patches by Mike Wolfram and Russell King.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

These are all the remaining instances of get_property.  Simple rename of
get_property to of_get_property.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This reverts commit d05c7a80,
which included changes which should go via other subsystem
maintainers.

The only unfortunate bit here is that the name field of struct map_info
is not const, so for now we put a cast on the assignment of it.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 40b36daa introduced possibility that serial8250_backup_timeout() ->
serial8250_handle_port() locks port.lock without disabling irqs, thus
allowing deadlock against interrupt handler (port.lock is acquired in
serial8250_interrupt()).

Spotted by lockdep.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Two functions are called from __devinit context, but they are marked as
__init. Fix this.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

irq values are u32, not u8. Large irq numbers will be truncated,
free_irq may free a different irq.

Remove incorrectly sized struct member and use the one from pci_dev.
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I encountered the following kernel panic.  The cause of this problem was
NULL pointer access in check_modem_status() in 8250.c.  I confirmed this
problem is fixed by the attached patch, but I don't know this is the
correct fix.

sadc[4378]: NaT consumption 2216203124768 [1]
Modules linked in: binfmt_misc dm_mirror dm_mod thermal processor fan
container button sg e100 eepro100 mii ehci_hcd ohci_hcd

    Pid: 4378, CPU 0, comm: sadc
    psr : 00001210085a2010 ifs : 8000000000000289 ip : [<a000000100482071>]
    Not tainted
    ip is at check_modem_status+0xf1/0x360

    Call Trace:
    [<a000000100013940>] show_stack+0x40/0xa0
    [<a0000001000145a0>] show_regs+0x840/0x880
    [<a0000001000368e0>] die+0x1c0/0x2c0
    [<a000000100036a30>] die_if_kernel+0x50/0x80
    [<a000000100037c40>] ia64_fault+0x11e0/0x1300
    [<a00000010000bdc0>] ia64_leave_kernel+0x0/0x280
    [<a000000100482070>] check_modem_status+0xf0/0x360
    [<a000000100482300>] serial8250_get_mctrl+0x20/0xa0
    [<a000000100478170>] uart_read_proc+0x250/0x860
    [<a0000001001c16d0>] proc_file_read+0x1d0/0x4c0
    [<a0000001001394b0>] vfs_read+0x1b0/0x300
    [<a000000100139cd0>] sys_read+0x70/0xe0
    [<a00000010000bc20>] ia64_ret_from_syscall+0x0/0x20
    [<a000000000010620>] __kernel_syscall_via_break+0x0/0x20

Fix the possible NULL pointer access in check_modem_status() in 8250.c.  The
check_modem_status() would access 'info' member of uart_port structure, but it
is not initialized before uart_open() is called.  The check_modem_status() can
be called through /proc/tty/driver/serial before uart_open() is called.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NTaku Izumi <izumi2005@soft.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace uses with of_find_node_by_name and for_each_node_by_name.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Convert the AMBA PL010 serial driver to use the clock infrastructure
to allow EP93xx platforms to properly gate the clock to the UARTs.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use a pointer to struct uart_amba_port throughout the driver
rather than a mixture of that and struct uart_port.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that

	CKEN0_PWM0 --> CKEN_PWM0
	CKEN1_PWM1 --> CKEN_PWM1
	...
	CKEN24_CAMERA --> CKEN_CAMERA

The reasons for the change of these defitions are:

1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24

2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for

3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off

Another change in the patch is to make the definitions equal to its
clock bit index, so that

   #define CKEN_CAMERA  (24)

instead of

   #define CKEN_CAMERA  (1 << 24)

this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: Neric miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>