The current code follows the spec but uses an overlong delay. This would
be great if the hardware did. Several vendors however forget the D7
pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to
skip detection as is done in drivers/ide. (ie this is a tested solution
over a long time)
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().

This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

sg increments the refcount of constituent pages in its higher order memory
allocations when they are about to be mapped by userspace.  This is done so
the subsequent get_page/put_page when doing the mapping and unmapping does not
free the page.

Move over to the preferred way, that is, using compound pages instead.  This
fixes a whole class of possible obscure bugs where a get_user_pages on a
constituent page may outlast the user mappings or even the driver.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Douglas Gilbert <dougg@torque.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

SLAB_NO_REAP is documented as an option that will cause this slab not to be
reaped under memory pressure.  However, that is not what happens.  The only
thing that SLAB_NO_REAP controls at the moment is the reclaim of the unused
slab elements that were allocated in batch in cache_reap().  Cache_reap()
is run every few seconds independently of memory pressure.

Could we remove the whole thing?  Its only used by three slabs anyways and
I cannot find a reason for having this option.

There is an additional problem with SLAB_NO_REAP.  If set then the recovery
of objects from alien caches is switched off.  Objects not freed on the
same node where they were initially allocated will only be reused if a
certain amount of objects accumulates from one alien node (not very likely)
or if the cache is explicitly shrunk.  (Strangely __cache_shrink does not
check for SLAB_NO_REAP)

Getting rid of SLAB_NO_REAP fixes the problems with alien cache freeing.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Do not use platform_device_register_simple() as it is going away, define
dcdbas_driver and implement ->probe() and ->remove() functions so manual
binding and unbinding will work with this driver.

Also switch to using attribute_group when creating sysfs attributes and
make sure to check and handle errors; explicitely remove attributes when
detaching driver.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Do not use platform_device_register_simple() as it is going away.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

mv64x600_wdt: convert to the new platform device interface Do not use
platform_device_register_simple() as it is going away.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The patch does the following for v441xx seris drivers:

 - stop using platform_device_register_simple() as it is going away
 - mark ->probe() and ->remove() methods as __devinit and __devexit
   respectively
 - initialize "owner" field in driver structure so there is a link
   from /sys/modules to the driver
 - mark *_init() and *_exit() functions as __init and __exit
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update the serial_txx9 driver.

 * More strict check in verify_port.  Cleanup.
 * Do not insert a char caused previous overrun.
 * Fix some spin_locks.
 * Do not call uart_add_one_port for absent ports.

Also, this patch removes a BROKEN tag from Kconfig.  This driver has been
marked as BROKEN by removal of uart_register_port, but it has been solved
already on Sep 2005.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The code that handles bios that span table target boundaries by breaking
them up into smaller bios will not split an individual struct bio_vec into
more than two pieces.  Sometimes more than that are required.

This patch adds a loop to break the second piece up into as many pieces as
are necessary.

Cc: "Abhishek Gupta" <abhishekgupt@gmail.com>
Cc: Dan Smith <danms@us.ibm.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The console cursor can be called in atomic context.  Change memory
allocation to use the GFP_ATOMIC flag in i810fb_cursor().
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Modules: PXA Mainstone driver,CX88 driver,SAA7134 driver

Replace snd_xxx_t typedefs with explicit structs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Make sure the callers do a pgprot_noncached() on
vma->vm_page_prot.

Pointed out by Hugh Dickens.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some PHYs should not be powered down in tg3_set_power_state() because
of bugs or other hardware limitations.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

5700 and 5701 will not return correct SRAM data when the chip is in
D3hot power state. tg3_get_eeprom_hw_cfg() must first put the device
in D0 before reading SRAM.

Thanks to Thomas Chenault at Dell for noticing this problem.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also, bump sata_vsc version.

Also, cleanup interrupt mask content and note in Kconfig that this
driver supports the Intel 31244.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Alan noted: "bmdma may be zero but the bmdma_irq_clear function gets
called even in this case during pure PIO operation. Check we have a
bmdma before we use it."

I fixed this by adding a check for zero.  While was I there, I fixed the
non-standard indentation of the small function's code.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The first performs the simplex clearing relevant to some chipsets that
report simplex by default but can in fact do more if poked. The second
is used to strip DMA modes from a PCI control with no BAR4 allocation.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch addresses a number of weird behaviours observed
for the sata_mv driver, by fixing an "off by one" bug in processing
of the EDMA response queue.

Basically, sata_mv was looking in the wrong place for
command results, and this produced a lot of unpredictable behaviour.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Encapsulate some of ata_scsi_slave_config so that parts
can be reused in future SAS patches.
Signed-off-by: NBrian King <brking@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add some dummy noop functions for use by libata clients
that do not need to do anything. Future SAS patches will
utilize these functions.
Signed-off-by: NBrian King <brking@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove the ATA_PROT_PIO_MULT protocol.
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add ata_port_flush_task() to ata_exec_internal().
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Original patch (and description) by Douglas Gilbert, with minor fixes
and API updates from me.

Changelog:
  - make existing libata VPD device identification page (0x83)
    supply the ATA serial number in the libata "vendor
    specific" designator (from Chris Paulson-Ellis)
  - add a "t10 vendor id based" designator as defined in
    SAT rev 08 (section 10.3.4.2.3) that supplies ATA
    model and serial numbers
  - make the libata VPD page 0x83 more extensible (for
    adding more designators in the future).
  - rename EVPD to VPD in various places. Enable Vital
    Product Data (EVPD) is a bit in the INQUIRY cdb.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Signed-off-by: NUwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

This reverts commit 08f1d0b9

The "bt8xx/ conversion" for drivers/video/ hasn't actually percolated
all the way to this tree, so the Makefile change escaped too soon.

Build breakage noticed by Jeff Garzik <jeff@garzik.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- undo some Lindent damage by indenting member names
- remove history at top of .c file, this is stored in the kernel
  repo changelog (in greater detail, even).

drivers/net/skfp/fplustm.c: In function `enable_formac':
drivers/net/skfp/fplustm.c:552: warning: large integer implicitly truncated to unsigned type
drivers/net/skfp/fplustm.c:555: warning: large integer implicitly truncated to unsigned type

These arguments were changed to `const', so the compiler can now see that it's
doing and outw(..., 0xffffnnnn).  Cast the arg to ushort.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

All accessor's different methods are now selected with C code and unused
ones statically optimized away at compile time instead of being selected
with #if's and #ifdef's.  This has many advantages such as allowing the
compiler to validate the syntax of the whole code, making it cleaner and
easier to understand, and ultimately allowing people to define
configuration symbols in terms of variables if they really want to
dynamically support multiple bus configurations at the same time (with
the unavoidable performance cost).
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Boards with multiple PHYs were not being handled properly by the pcnet32
driver.  This patch by Thomas Bogendoerfer with changes by me will allow
Allied Telesyn 2700FTX and 2701FTX boards to use either the copper or
the fiber interfaces.  It has been tested on ia32 and ppc64 hardware.
Philippe Seewer also tested and improved the patch.
ethtool for pcnet32 already supports multiple phys.

See also bugzilla bug 4219.

Please apply to 2.6.16
Signed-off-by: NDon Fry <brazilnut@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>