- 07 10月, 2010 25 次提交
-
-
由 Stanislaw Gruszka 提交于
This reverts commit 7acc7c68. It was applied to avoid possible warning in ieee80211_restart_hw, however reason of the warning were races in mac80211, currently hopefully fixed. Not reseting device when performing scan is bad for two reasons. When forcing reset from iwl_check_stuck_queue(), in case of fail, reset will be repeated until scan finish. But since firmware is in bad shape, scan only finish after scan_check work (about 7s). So we will delay the reset, what is not good behaviour. When forcing reset from iwl_recover_from_statistics(), we will not repeat the reset, so we will not perform reset at all when needed. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
We nulify local->scan_req on failure in __ieee80211_start_scan, so __ieee80211_scan_completed will not call cfg80211_scan_done. Fix that. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
When performing hw scan and not abort it, __ieee80211_scan_completed() is currently called from scan work, so does not need to reschedule work to call drv_hw_scan(). Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
This is partial revert and fix for commit 85f72bc8 "mac80211: only cancel software-based scans on suspend" When cfg80211 request the scan and mac80211 perform some management work, we defer the scan request. We do not canceling such requests when calling ieee80211_scan_cancel(), because of SCAN_SW_SCANNING bit check just before the call. So fix that problem. Another problem, which commit 85f72bc8 tries to solve, is we can not cancel HW scan. Hence patch make ieee80211_scan_cancel() ignore HW scan (see code comments). Keeping local->mtx lock assures that the deferred scan will not become "working" HW scan. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
We are taking local->mtx inside __ieee80211_scan_completed(), but just before call to that function we drop the lock. Dropping/taking lock is not good, because can lead to hard to understand race conditions. Patch split scan_completed() code into two functions, first must be called with local->mtx taken and second without it. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Use goto instruction to call __ieee80211_scan_completed only ones in ieee80211_scan_work. This is prepare for the next patch. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
It's already set in PHY common code. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Yikes! The error return keeps a netdev reference and the rdev mutex locked, fix that! Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This adds API to allow adding per-station GTKs, updates mac80211 to support it, and also allows drivers to remove a key from hwaccel again when this may be necessary due to multiple GTKs. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
When roaming while we have active BA session, we can end up transmitting delBA frames to the old AP while we're already on the new AP's channel, which can cause warnings. Simply avoid sending those frames, but still tear down the internal session state, since they are not really necessary anyway as we will implicitly disassociate when sending the association to the new AP. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Senthil Balasubramanian 提交于
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Senthil Balasubramanian 提交于
drv_config callback is called only after the ack for the nullframe is received and so driver need not do anything special for this. So remove NULLFUNC_COMPLETED, PS_ENABLED flags and bf_isnullfunc flags from ath9k as mac80211 already handles them properly. Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
After the last rounds of cleanup, these functions are now functionally equivalent and can thus be merged. Also get rid of some excessive (and redundant) debug messages. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
The code gets more concise and readable when making the new ANI functions fall back to the old ones if ANI v2 is disabled. This also makes further code cleanup easier. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
Split out the PHY error counter update from ath9k_hw_ani_monitor_*, reuse it in ath9k_hw_proc_mib_event (merged from ath9k_hw_proc_mib_event_old and ath9k_hw_proc_mib_event_new). Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
ANI state is kept per channel, so instead of keeping an array of ANI states with an arbitrary size of 255, move the ANI state into the channel struct. Move some config settings that are not per-channel out of the per-channel struct to save some memory. With those changes, ath9k_ani_restart_old and ath9k_ani_restart_new can be merged into a single function. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
Throughout the code, DISABLE_REGWRITE_BUFFER is always called right after REGWRITE_BUFFER_FLUSH. Since that's unlikely to change any time soon, that makes keeping those ops separate rather pointless, as it only increases code size and line number counts. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
The cycle counters are used by ANI to determine the amount of time that the radio spent not receiving or transmitting. They're also used for debugging purposes if the baseband watchdog on AR9003 detects a lockup. In the future, we want to use these counters to determine the medium utilization and export this information via survey. For that, we need to make sure that the counter is only accessed from one place, which also ensures that wraparounds won't occur at inconvenient points in time. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
The calibration actual calibration flags are only used by the per chip family source files, so it makes more sense to define them in those files instead of globally. That way the code has to test for less flags. Also instead of using a separate callback for testing whether a particular calibration type is supported, simply adjust ah->supp_cals in the calibration init which is called right after the hardware reset, before any of the calibrations are run. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
We never delete the addBA response timer, which is typically fine, but if the station it belongs to is deleted very quickly after starting the BA session, before the peer had a chance to reply, the timer may fire after the station struct has been freed already. Therefore, we need to delete the timer in a suitable spot -- best when the session is being stopped (which will happen even then) in which case the delete will be a no-op most of the time. I've reproduced the scenario and tested the fix. This fixes the crash reported at http://mid.gmane.org/4CAB6F96.6090701@candelatech.com Cc: stable@kernel.org Reported-by: NBen Greear <greearb@candelatech.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
wireless-testing commit 37e5bf65 Author: Luis R. Rodriguez <lrodriguez@atheros.com> Date: Sat Jun 12 00:33:40 2010 -0400 ath9k_hw: fix clock rate calculations for ANI This commit accidentally broke clock rate calculation by doubling the calculated clock rate Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 06 10月, 2010 15 次提交
-
-
由 Luis R. Rodriguez 提交于
Be consistent and use the wk->chan instead of the local->hw.conf.channel for the association done work. This prevents any possible races against channel changes while we run this work. In the case that the race did happen we would be initializing the bit rates for the new AP under the assumption of a wrong channel and in the worst case, wrong band. This could lead to trying to assuming we could use CCK frames on 5 GHz, for example. This patch has a fix for kernels >= v2.6.34 Cc: stable@kernel.org Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The documentation for NL80211_CMD_REMAIN_ON_CHANNEL isn't accurate, an interface index is required by the command. Update it accordingly. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gabor Juhos 提交于
The base_eep_header_4k structure contains information that the device supports high power tx gain table or not. However the ath9k_hw_4k_get_eeprom function does not return that value when it is called with EEP_TXGAIN_TYPE. This leads to that the tx gain initialization will use the init values from the original tx gain table even if the device inidicates that the high power table should be used. Changes-licensed-under: ISC Signed-off-by: NGabor Juhos <juhosg@openwrt.org> Signed-off-by: NShu Hwa Shen <shensh@zcomm.com.cn> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bruno Randolf 提交于
We should only wake up queues which mac80211 knows about (queues 0-3). We have another internal queue ("CAB", queue number 6) which we use for power-saved frames. When transmitted frames are processed from this queue, we have to make sure we don't bother mac80211 with waking a queue it doesn't know about. this fixes: WARNING: at /home/br1/ath/wireless-testing/net/mac80211/util.c:275 __ieee80211_wake_queue+0xd6/0xe0 [mac80211]() Signed-off-by: NBruno Randolf <br1@einfach.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The locking around ieee80211_recalc_smps is buggy -- it cannot acquire another interface's mutex while the iflist mutex is held because another code path could be holding the iface mutex and trying to acquire the iflist mutex. But the locking is also unnecessary, we only check "ifmgd->associated" as a bool, and don't use the pointer (in check_mgd_smps). Reported-by: NBen Greear <greearb@candelatech.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Consolidate boilerplate code needed for .dumpit calls operating on netdevs. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Use a new flag that requires the netdev to be UP and use it to check instead of coding the check into all functions that require it. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This makes nl80211 use the new genetlink pre_doit/post_doit hooks for locking and checking the interface/wiphy index. This significantly reduces the code size and the likelihood of locking errors. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Each family may have some amount of boilerplate locking code that applies to most, or even all, commands. This allows a family to handle such things in a more generic way, by allowing it to a) include private flags in each operation b) specify a pre_doit hook that is called, before an operation's doit() callback and may return an error directly, c) specify a post_doit hook that can undo locking or similar things done by pre_doit, and finally d) include two private pointers in each info struct passed between all these operations including doit(). (It's two because I'll need two in nl80211 -- can be extended.) Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Acked-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Carpenter 提交于
If kzalloc() fails then return should return with -ENOMEM. Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bruno Randolf 提交于
Enable WME QoS in IBSS mode by adding a WME information element to beacons and probe respones and by checking for it and marking stations as WME capable if it is present. Signed-off-by: NBruno Randolf <br1@einfach.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Helmut Schaa 提交于
If a frame is not meant to be sent as AMPDU or part of it the hw might still decide to aggregate this frame if a previous frame started an AMPDU. However, this will limit the usefulness of the reported tx rate since the reported rate will be the one specified in the TXWI of the first frame and thus it is not possible to reliably caculate the number of retrys by substracting the reported tx rate from the tx rate in the TXWI. To fix this issue, only report the successful rate for frames that were not meant to be aggregated but ended up in an aggregate. Example: Frame A (MCS7, AMPDU=1) B (MCS7, AMPDU=1) C (MCS12, AMDPU=0, PROBE_RATE) Although frame C shoudn't be aggregated the hw might sill put it into an AMPDU together with A and B. If the transmission succeeds the tx status will contain MCS7 for all three frames. In that case we should only report MCS7 as success rate and avoid reporting MCS12-MCS8 as failed tx attempts as this will affect the future rate control decisions. This oddity might strike us in other scenarious as well but the most common "wrong" report happened for frames used to probe a different tx rate. This improves the rate control decisions notable. Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Helmut Schaa 提交于
In order to lower the impact of probe rates don't send a frame as AMPDU if the rate control algorithm sets IEEE80211_TX_CTL_RATE_CTRL_PROBE. Otherwise a whole aggregate would be send with a probe rate which might lead to numerous retries. Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Helmut Schaa 提交于
When rt2x00lib_enable_radio fails to enable the radio, rt2x00lib_start will call rt2x00queue_uninitialize to uninitialize the queues. Since, the queues are not initialized here but already in rt2x00lib_initialize we shouldn't uninitialize the queues here. Otherwise, a consecutive call to rt2x00lib_start will oops (see below) because it assumes the queues are already initialized. BUG: unable to handle kernel NULL pointer dereference at 00000010 IP: [<f8d2d901>] :rt2800pci:rt2800pci_clear_entry+0x1/0x40 *pde = 00000000 Oops: 0000 [#1] SMP Modules linked in: ... rt2800pci ... Pid: 5995, comm: hostapd Not tainted (2.6.27.8 #1) EIP: 0060:[<f8d2d901>] EFLAGS: 00210246 CPU: 3 EIP is at rt2800pci_clear_entry+0x1/0x40 [rt2800pci] EAX: 00000000 EBX: f698863c ECX: 00200296 EDX: f8d2dee0 ESI: f6988600 EDI: f5b6f000 EBP: 00000000 ESP: f6d75e4c DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 Process hostapd (pid: 5995, ti=f6d74000 task=f6ce2300 task.ti=f6d74000) Stack: f698863c fa00eaec 00000000 f5b6f000 00000000 f7b67000 f5b6e280 fa00c629 f5b6f000 00000000 fa00ca3d f7b67480 00000001 fa177d4c 01b6e890 f7b67000 00000000 f7b67000 00000001 00001003 00001002 c066c366 f7b67000 c0668ad0 Call Trace: [<fa00eaec>] rt2x00queue_init_queues+0x5c/0x90 [rt2x00lib] [<fa00c629>] rt2x00lib_enable_radio+0x29/0xa0 [rt2x00lib] [<fa00ca3d>] rt2x00lib_start+0x5d/0xd0 [rt2x00lib] [<fa177d4c>] ieee80211_do_open+0x21c/0x510 [mac80211] [<c066c366>] dev_open+0x56/0xb0 [<c0668ad0>] dev_set_rx_mode+0x20/0x40 [<c066a67f>] dev_change_flags+0x7f/0x190 [<c06b1495>] devinet_ioctl+0x515/0x690 [<c0668d24>] __dev_get_by_name+0x74/0x90 [<c065d3f0>] sock_ioctl+0xd0/0x240 [<c065d320>] sock_ioctl+0x0/0x240 [<c018179b>] vfs_ioctl+0x2b/0x90 [<c0181a5b>] do_vfs_ioctl+0x25b/0x2a0 [<c0181af6>] sys_ioctl+0x56/0x70 [<c0103262>] syscall_call+0x7/0xb [<c0700000>] add_card+0xad0/0xba0 ======================= Code: 83 78 08 0e 74 14 8b 02 8b 48 04 85 c9 0f 99 c0 0f b6 c0 c3 8d b6 00 00 00 00 8b 02 8b 40 04 85 c0 0f 99 c0 0f b6 c0 c3 66 90 53 <8b> 48 10 8b 58 08 8b 40 04 83 78 08 0e 74 15 8b 11 83 c2 04 8b EIP: [<f8d2d901>] rt2800pci_clear_entry+0x1/0x40 [rt2800pci] SS:ESP 0068:f6d75e4c ---[ end trace cff9a5c094bb8837 ]--- Reported-by: NJoshua Smith <jesmith@kaon.com> Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>