If no_console_suspend is used we have prevent uart idling during suspend
to provide debug prints.

Power domain hooks can idle uarts if left enabled during system wide suspend
so re-use the omap_device_disable_idle_on_suspend API's to ensure console_uart
is not idled during suspend.

omap_device_disable_idle_on_suspend API was used on all uarts since the uart
driver was not runtime adapted, now with runtime adaptation we can re-use this
API only for no_console_suspend use cases.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Omap-uart can be used as console uart to print early boot messages using
earlyprintk so for console uart prevent hwmod reset or idling during bootup.

Identify omap-uart used as console and avoid idling rather than preventing
all omap-uarts from idling during bootup. Update the comments for the same.

Remove the uart idling and enabling back using hwmod_idle/omap_device_enable
for all uarts that where left enabled from boot to set the hwmod framework
state machine right. This need not be taken care any more serial.c rather
can be handled within the hwmod framework.
Reference: http://www.spinics.net/lists/linux-omap/msg60300.htmlSigned-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Reuse the num_uarts variable itself to count number of uarts.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

When using DMA there are two timeouts defined. The first timeout,
rx_timeout, is really a polling rate in which software polls the
DMA status to see if the DMA has finished. This is necessary for
the RX side because we do not know how much data we will receive.
The secound timeout, RX_TIMEOUT, is a timeout after which the
DMA will be stopped if no more data is received. To make this
clearer, rename rx_timeout as rx_poll_rate and rename the
function serial_omap_rx_timeout() to serial_omap_rxdma_poll().

The OMAP-Serial driver defines an RX_TIMEOUT of 3 seconds that is
used to indicate when the DMA for UART can be stopped if no more
data is received. The value is a global definition that is applied
to all instances of the UART.

Each UART may be used for a different purpose and so the timeout
required may differ. Make this value configurable for each UART so
that this value can be optimised for power savings.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

The following UART parameters are defined within the UART driver:

1). Whether the UART uses DMA (dma_enabled), by default set to 0
2). The size of dma buffer (set to 4096 bytes)
3). The time after which the dma should stop if no more data is received.
4). The auto suspend delay that will be passed for pm_runtime_autosuspend
    where uart will be disabled after timeout

Different UARTs may be used for different purpose such as the console,
for interfacing bluetooth chip, for interfacing to a modem chip, etc.
Therefore, it is necessary to be able to customize the above settings
for a given board on a per UART basis.

This change allows these parameters to be configured from the board file
and allows the parameters to be configured for each UART independently.

If a board does not define its own custom parameters for the UARTs, then
use the default parameters in the structure "omap_serial_default_info".
The default parameters are defined to be the same as the current settings
in the UART driver to avoid breaking the UART for any cuurnelty supported
boards. By default, make all boards use the default UART parameters.
Signed-off-by: NDeepak K <deepak.k@ti.com>
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

With runtime adaptation done remove clock_enable/disbale API's
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

From the runtime callbacks enable hwmod wakeups for uart which will
internally enable io-pad wakeups for uarts if they have rx-pad pins
set as wakeup capabale.

Use the io-ring wakeup mechanism after uart clock gating and leave
the PM_WKST set for uart to default reset values cleanup the
code in serial.c which was handling PM_WKST reg.
Irq_chaing(PRM_DRIVER) is used to wakeup uart after uart clocks are gated
using pad wakeup mechanism.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

Move the errata handling mechanism from serial.c to omap-serial file
and utilise the same func in driver file.

Errata i202, i291 are moved to be handled with omap-serial
Moving the errata macro from serial.c file to driver header file
as from on errata will be handled in driver file itself.
Corrected errata id from chapter reference 2.15 to errata id i291.

Removed errata and dma_enabled fields from omap_uart_state struct
as they are no more needed with errata handling done within omap-serial.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Avoid unconditional context restore every time we gate uart
clocks. Check whether context loss happened based on which
we can context restore uart regs from uart_port structure.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

Remove the uart reset function which is configuring the
TX empty irq which can now be handled within omap-serial driver.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

Remove context save function from serial.c and move context restore
function to omap-serial. Remove all regs stored in omap_uart_state
for contex_save/restore, reg read write funcs used in context_save/restore,
io_addresses populated for read/write funcs.

Clock gating mechanism was done in serial.c and had no info on uart state
thus we needed context save and restore in serial.c
With runtime conversion and clock gating done within uart driver
context restore can be done from regs value available from uart_omap_port
structure.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

The mapbase (start_address), membase(io_remap cookie) part of
pdata struct omap_uart_port_info are removed as this should be
derived within driver.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

Padconf wakeup is used to wakeup uart after uart fclks/iclks are gated.
Rx-Pad wakeup was done by writing to rx-pad offset value populated in
serial.c idle_init. Remove the direct reading and writing into rx pad.
Remove the padconf field part of omap_uart_state struct and pad offsets
populated.

Now with mux framework support we can use mux_utilities
along with hmwod framework to handle io-pad configuration and enable rx-pad
wake-up mechanism.

To avoid breaking any board support add default mux data for all uart's
if mux info is not passed from board file.
With the default pads populated in serial.c wakeup capability for
rx pads is set, this can be used to enable uart_rx io-pad wakeup from
hwmod framework. The pad values in 3430sdp/4430sdp/omap4panda board file
are same as the default pad values populated in serial.c. Remove pad values
from 3430sdp/4430sdp/omap4panda board file and use the default pads
from serial.c file.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Currently we use a shared irq handler to identify uart activity and then
trigger a timer. By default the timeout value is zero and can be set or
modified from sysfs. If there was no uart activity for the period set
through sysfs, the timer will expire and call timer handler this will
set a flag can_sleep using which decision to gate uart clocks can be taken.

Since the clock gating mechanism is outside the uart driver, we currently
use this mechanism. In preparation to runtime implementation for omap-serial
driver we can cleanup this mechanism and use runtime API's to gate uart clocks.

Removes the following:
* timer related info from local uart_state struct
* the code used to set timeout value from sysfs.
* irqflags used to set shared irq handler.
* un-used function omap_uart_check_wakeup.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

We had been using traditional 8250 driver as uart console driver
prior to omap-serial driver. Since we have omap-serial driver
in mainline kernel for some time now it has been used as default
uart console driver on omap2+ platforms. Remove 8250 support for
omap-uarts.

Serial_in and serial_out override for 8250 serial driver is also
removed. Empty fifo read fix is already taken care with omap-serial
driver with data ready bit check from LSR reg before reading RX fifo.
Also waiting for THRE(transmit hold reg empty) is done with wait_for_xmitr
in omap-serial driver.

Serial_in/out overrides are not neceesary for omap-serial driver
and things that are taken with omap-serial driver are removed here.

Remove headers that were necessary to support 8250 support
and remove all config bindings done to keep 8250 backward compatibility
while adding omap-serial driver. Remove omap_uart_reset needed for
8250 autoconf.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

In preparation to UART runtime conversion remove uart specific calls
from pm24xx/34xx files and their definition from serial.c
These func calls will no more be used with upcoming uart runtime design.

1.) omap_uart_prepare_suspend :- can be taken care with driver suspend hooks.
2.) omap_uart_enable_irqs :- Used to enable/disable uart irq's in suspend
    path from PM code, this is removed as same is handled by
    uart_suspend_port/uart_resume_port in omap-serial driver which will
    do an port_shutdown on suspend freeing irq and port_startup on resume
    enabling back irq.
3.) Remove prepare_idle/resume_idle calls used to gate uart clocks.
    UART clocks can be gated within driver using runtime funcs
    and be woken up using irq_chaining from omap_prm driver.
4.) Remove console_locking from idle path as clock gating is done withing
    driver itself with runtime API. Remove is_suspending check used to acquire
    console_lock.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This patch updates existing macros, functions used for TI816X, to enable
addition of other SoCs belonging to TI81XX family (e.g., TI814X).

The approach taken is to use TI81XX/ti81xx for code/data going to be common
across all TI81XX devices.

cpu_is_ti81xx() is introduced to handle code common across TI81XX devices.

In addition, ti8168_evm_map_io() is now replaced with ti81xx_map_io() and moved
in mach-omap2/common.c as same will be used for TI814X and is not board
specific.
Signed-off-by: NHemant Pedanekar <hemantp@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updates the common machine specific source files for
support for AM33XX/AM335x with cpu type, macros for identification of
AM33XX/AM335X device.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
[tony@atomide.com: updated for map_io and common.h changes, dropped CK_AM33XX]
Signed-off-by: NTony Lindgren <tony@atomide.com>

As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.

Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove all these duplicated structures since a default one is now
available.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Public omap_device functions need to take platform_device pointers,
conversion to omap_device pointers is done internal to the omap_device
layer.
Signed-off-by: NKevin Hilman <khilman@ti.com>

All of the device init and device driver interaction with omap_device
is done using platform_device pointers.  To make this more explicit,
have omap_device return a platform_device pointer instead of an
omap_device pointer.

All current users of the omap_device pointer were only using it to get
at the platform_device pointer or struct device pointer, so fixing all
of the users was trivial.

This also makes it more difficult for device init code to directly
access members of struct omap_device, and allows for easier changing
of omap_device internals.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Until these drivers are runtime PM converted, their device power
states are managed by calling custom driver hooks late in the
idle/suspend path.  Therefore, do not let the suspend/resume core code
automatically idle these devices since they will be managed manually
by the OMAP PM core very late in the idle/suspend path.
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Rename omap_hwmod_init() to omap_hwmod_register().  Rename
omap_hwmod_late_init() to omap_hwmod_setup_all().  Also change all of
the callers to reflect the new names.  While here, update some
copyrights.

Suggested by Tony Lindgren <tony@atomide.com>.

N.B. The comment in mach-omap2/serial.c may no longer be correct, given
     recent changes in init order.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

This patch updates the common machine specific source files with support for
TI816X.
Signed-off-by: NHemant Pedanekar <hemantp@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The new init_early hook happens at the end of setup_arch,
which is too early for kzalloc. However, there's no need
to call omap_serial_early_init that early, so fix this
by setting it up as a core_initcall.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Tested-by: NKevin Hilman <khilman@ti.com>

The -rt patches change the console_semaphore to console_mutex.  As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()

This commit makes things use more neutral function names which dont make
implications about the underlying lock.

The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()

This patch also paves the way to switching console_sem from a semaphore to
a mutex.

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: NTorben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is needed to pass board specific data such as pads used to the
platform level driver init code.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Now that OMAP4-specific PRCM functions have been added, distinguish the
existing OMAP2/3-specific PRCM functions by prefixing them with "omap2_".

This patch should not result in any functional change.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NRajendra Nayak <rnayak@ti.com>

In preparation for adding OMAP4-specific PRCM accessor/mutator
functions, split the existing OMAP2/3 PRCM code into OMAP2/3-specific
files.  Most of what was in mach-omap2/{cm,prm}.{c,h} has now been
moved into mach-omap2/{cm,prm}2xxx_3xxx.{c,h}, since it was
OMAP2xxx/3xxx-specific.

This process also requires the #includes in each of these files to be
changed to reference the new file name.  As part of doing so, add some
comments into plat-omap/sram.c and plat-omap/mcbsp.c, which use
"sideways includes", to indicate that these users of the PRM/CM includes
should not be doing so.

Thanks to Felipe Contreras <felipe.contreras@gmail.com> for comments on this
patch.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: NOmar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: NFelipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: NKevin Hilman <khilman@deeprootsystems.com>
Tested-by: NKevin Hilman <khilman@deeprootsystems.com>
Tested-by: NRajendra Nayak <rnayak@ti.com>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Change the per-hwmod mutex to a spinlock.  (The per-hwmod lock
serializes most post-initialization hwmod operations such as enable,
idle, and shutdown.)  Spinlocks are needed, because in some cases,
hwmods must be enabled from timer interrupt disabled-context, such as
an ISR.  The current use-case that is driving this is the OMAP GPIO
block ISR: it can trigger interrupts even with its clocks disabled,
but these clocks are needed for register accesses in the ISR to succeed.

This patch also effectively reverts commit
84824022 - this patch makes
_omap_hwmod_enable() and _omap_hwmod_init() static, renames them back
to _enable() and _idle(), and changes their callers to call the
spinlocking versions.  Previously, since omap_hwmod_{enable,init}()
attempted to take mutexes, these functions could not be called while
the timer interrupt was disabled; but now that the functions use
spinlocks and save and restore the IRQ state, it is appropriate to
call them directly.

Kevin Hilman <khilman@deeprootsystems.com> originally proposed this
patch - thanks Kevin.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Access to some registers depends on register access mode
Three different modes are available for OMAP (at least)
• Operational mode     LCR_REG[7] = 0x0
• Configuration mode A LCR_REG[7] = 0x1 and LCR_REG[7:0]! = 0xBF
• Configuration mode B LCR_REG[7] = 0x1 and LCR_REG[7:0]  = 0xBF

Define access modes and remove redefinitions and magic numbers
in serial drivers (and later in bluetooth driver).
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Define MDR1 register serial definitions used in serial and
bluetooth drivers.
Change magic number to ones defined in serial_reg for omap1/2
serial driver.
Remove redefined MDR1 register definitions in omap-serial driver.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: NG, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The console semaphore must be held while the OMAP UART devices are
disabled, lest a console write cause an ARM abort (and a kernel crash)
when the underlying console device is inaccessible.  These crashes
only occur when the console is on one of the OMAP internal serial
ports.

While this problem has been latent in the PM idle loop for some time,
the crash was not triggerable with an unmodified kernel until commit
6f251e9d ("OMAP: UART: omap_device
conversions, remove implicit 8520 assumptions").  After this patch, a
console write often occurs after the console UART has been disabled in
the idle loop, crashing the system.  Several users have encountered
this bug:

    http://www.mail-archive.com/linux-omap@vger.kernel.org/msg38396.html

    http://www.mail-archive.com/linux-omap@vger.kernel.org/msg36602.html

The same commit also introduced new code that disabled the UARTs
during init, in omap_serial_init_port().  The kernel will also crash
in this code when earlyconsole and extra debugging is enabled:

    http://www.mail-archive.com/linux-omap@vger.kernel.org/msg36411.html

The minimal fix for the -rc series is to hold the console semaphore
while the OMAP UARTs are disabled.  This is a somewhat overbroad fix,
since the console may not be located on an OMAP UART, as is the case
with the GPMC UART on Zoom3.  While it is technically possible to
determine which devices the console or earlyconsole is actually
running on, it is not a trivial problem to solve, and the code to do
so is not really appropriate for the -rc series.

The right long-term fix is to ensure that no code outside of the OMAP
serial driver can disable an OMAP UART.  As I understand it, code to
implement this is under development by TI.

This patch is a collaboration between Paul Walmsley <paul@pwsan.com>
and Tony Lindgren <tony@atomide.com>.  Thanks to Ming Lei
<tom.leiming@gmail.com> and Pramod <pramod.gurav@ti.com> for their
feedback on earlier versions of this patch.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Pramod <pramod.gurav@ti.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Govindraj.R <govindraj.raja@ti.com>

Add additional check to omap_uart_resume_idle() so that only
enabled (specifically, idle-enabled) UARTs are allowed to resume.
This matches the existing check in prepare idle.

Without this patch, the system will hang if a board is
configured to register only some uarts instead of all of
them and PM is enabled.

Cc: Govindraj R. <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated description]
Signed-off-by: NTony Lindgren <tony@atomide.com>

"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

On OMAP24xx, UART2 WKEN and WKST registers are in PM_WKEN2_CORE and
PM_WKST2_CORE respecitvely.  Fix the OMAP2 register init to use the
correct registers on OMAP24xx.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The omap2plus_defconfig doesn't boot up when built with CONFIG_PM
disabled on the latest linux-omap master. Below are the observations
1. OMAP3 reboots in the middle of boot
--------------------------------------------------
[    0.000000] Calibrating delay loop... 494.72 BogoMIPS (lpj=1933312)
[    0.000000] pid_max: default: 32768 minimum: 301
[    0.000000] Security Framework initialized
[    0.000000] Mount-cache hash table entries: 512
[    0.000000] CPU: Testing write buffer coherency: ok
[    0.000000] Brought up 1 CPUs
[    0.000000] SMP: Total of 1 processors activated (494.72 BogoMIPS).
[    0.000000] regulator: core version 0.5
[    0.000000] NET: Registered protocol family 16

U-Boot 1.1.4 (Feb 11 2009 - 16:10:23)

OMAP3430-GP rev 2, CPU-OPP2 L3-165MHz
TI 3430SDP 1.0 Version + mDDR (Boot NOR)
DRAM:  128 MB
Flash: 128 MB
NAND:128 MiB
--------------------------------------------------

2. OMAP4 does a kernel PANIC
-------------------------------------
[    0.000000] Calibrating delay loop... 1195.29 BogoMIPS (lpj=4669440)
[    0.000000] pid_max: default: 32768 minimum: 301
[    0.000000] Security Framework initialized
[    0.000000] Mount-cache hash table entries: 512
[    0.000000] CPU: Testing write buffer coherency: ok
[    0.000000] L310 cache controller enabled
[    0.000000] l2x0: 16 ways, CACHE_ID 0x410000c2, AUX_CTRL 0x0e050000
[    0.000000] CPU1: Booted secondary processor
[    0.000000] Brought up 2 CPUs
[    0.000000] SMP: Total of 2 processors activated (2395.78 BogoMIPS).
[    0.000000] regulator: core version 0.5
[    0.000000] NET: Registered protocol family 16
[    0.000000] mux: Could not set signal i2c2_scl.i2c2_scl
[    0.000000] mux: Could not set signal i2c2_sda.i2c2_sda
[    0.000000] mux: Could not set signal i2c3_scl.i2c3_scl
[    0.000000] mux: Could not set signal i2c3_sda.i2c3_sda
[    0.000000] mux: Could not set signal i2c4_scl.i2c4_scl
[    0.000000] mux: Could not set signal i2c4_sda.i2c4_sda
-------------------------------------

This is happening because 'omap_serial_init()' is hanging in the boot.
On OMAP3 the watchdog is generating reboot because devices_init doesn't
happens where as on OMAP4 it just hangs without reboot.
The uart clock is not getting enabled after omap_device_idle as part
of omap_serial_init.
The omap_device_idle(will disable the clock) then omap_uart_block_sleep()
should enable clock back disabled during the boot up phase.
But omap_uart_block_sleep() stuffed version is binded only under
CONFIG_PM and other version is just empty. Hence it is not enabling
clock back as expected

This patch adds uart clock enable code to omap_uart_block_sleep() function
built with CONFIG_PM disabled.
Thanks to Charulatha and Govindraj for their help on this debug.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NCharulatha V <charu@ti.com>
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap.  This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.

In response, move the SCM headers into mach-omap2/.

As part of this, remove the direct SCM access from the OMAP UDC
driver.  It was clearly broken.  The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>

This patch makes the following:
 - Adds missing wakeup padding register handling.
 - Fixes a hardcode to use PER module ONLY on UART3.
Signed-off-by: NSergio Aguirre <saaguirre@ti.com>
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>