Now that we have improved the runtime power management powerup/powerdown
code, we believe that MMC_CAP_POWER_OFF_CARD is no longer necessary:
runtime PM should now work everywhere.

The only hard evidence for introducing MMC_CAP_POWER_OFF_CARD was the
Marvell sd8686 wifi chip, which was believed to require external gpio
manipulation which wasn't supported by some boards.

After further investigation it was realized (and confirmed by Marvell
folks) that sd8686 requirements can be fulfilled by changing the reset
sequence itself, even if no external gpio is manipulated.

For further information, see the following thread:
http://www.mail-archive.com/linux-mmc@vger.kernel.org/msg04289.html

Enable this trivially for a release or two. If no problems are reported,
we will follow up with a more extensive patch to remove this flag
altogether. If problems are reported, we can look at whitelist/blacklist
possibilities as before.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add description on how to enable random fault injection
for MMC IO.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Acked-by: NAkinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This adds support to inject data errors after a completed host transfer.
The mmc core will return error even though the host transfer is successful.
This simple fault injection proved to be very useful to test the
non-blocking error handling in the mmc_blk_issue_rw_rq().
Random faults can also test how the host driver handles pre_req()
and post_req() in case of errors.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Acked-by: NAkinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Export symbols should_fail() and fault_create_debugfs_attr() in order
to let modules utilize the fault injection framework.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Acked-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Eanble the ADMA2 mode for freescale esdhc imx driver, tested on MX25
3DS board, MX51 BBG board and MX53 LOCO board.

This patch is only used to enable the ADMA2 for MX51/53 platforms.
MX25/35 can't support the ADMA2 mode, set BROKEN_ADMA quirk on
MX25/35 platforms.

The ADMA mode supported or not can be distinguished by bit 20 of
the Capability Register (offset 0x40) in the FSL eSDHC module.
Signed-off-by: NRichard Zhu <richard.zhu@linaro.org>
Tested-and-acked-by: NEric Miao <eric.miao@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Remove the use of irq_to_gpio() in the card detection interrupt
handler. The information is available in the board structure and
we can avoid using a function that has little meaning.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes a potential issue about PDC interrupts. For example we
have a ENDRX pending interrupt and a RXBUFF pending interrupt. We have
received the RXBUFF interrupt but the transfer is not finished (so we
didn't have time to give a new buffer to the PDC controller). Then we
will compute ENDRX interrupt and we will give a new buffer to the PDC
controller, just after we will compute the RXBUFF interrupt and give
one or two new buffers to the PDC controller but we are not sure that
the first buffer given has been filled. So in this situation we may
have "lost" one sg buffer. It's the same for transmission.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Assuming that a sg buffer size is a page size is false so use sg_dma_len.
A 4096 bytes can be required with two 2048-bytes sg buffer.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Rename atmci_start_command() to atmci_send_command() which is more
appropriate; atmci_start_command suggests we're sending a start command.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add pdc support for atmel-mci. It makes at91-mci driver useless because it
was only used for the old atmel MCI core which has pdc but no dma support.
To allow removing at91-mci, the capabilities of the MCI core are detected
at runtime -- then the driver will use pio, pdc or dma transfers.
Warning: at91rm9200 is not supported, to support it we need to use swab32
on data but I have no board to test it.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Change atmci_readl and atmci_writel macros: remove string concatenation.
We can use these macros with registers which are not prefixed by ATMCI_.
This is the case if we want to write PDC registers which are common to
several devices so they are not prefixed with ATMCI_.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Homogenize namespace to atmci.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Private rx_csum flags are now duplicate of netdev->features & NETIF_F_RXCSUM.
Removing this needs deeper surgery.

Things noticed:
 - HW VLAN acceleration probably can be toggled, but it's left as is
 - the resets on RX csum offload change can probably be avoided
 - there is A LOT of copy-and-pasted code here
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When enabling hardware timestamping for ptp v2 event packets, the
software does not setup the queue for l4 packets, although layer 4
packets are valid for v2. This patch adds the flag which enables
setting up a queue and enabling udp packet timestamping.
Signed-off-by: NJacob E Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implements the new netdev op to allow user configuration of spoof
checking on a per VF basis.

V2 - Change netdev spoof check op setting to bool
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add configuration setting for drivers to turn spoof checking on or off
for discrete VFs.

v2 - Fix indentation problem, wrap the ifla_vf_info structure in
     #ifdef __KERNEL__ to prevent user space from accessing and
     change function paramater for the spoof check setting netdev
     op from u8 to bool.
v3 - Preset spoof check setting to -1 so that user space tools such
     as ip can detect that the driver didn't report a spoofcheck
     setting.  Prevents incorrect display of spoof check settings
     for drivers that don't report it.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 67fd4fcb (e1000e: convert to stats64) added the ability to update
statistics more accurately and on-demand through the net_device_ops
.ndo_get_stats64 hook, but introduced a locking bug on 82577/8/9 when
linked at half-duplex (seen on kernels with CONFIG_DEBUG_ATOMIC_SLEEP=y and
CONFIG_PROVE_LOCKING=y).  The commit introduced code paths that caused a
mutex to be locked in atomic contexts, e.g. an rcu_read_lock is held when
irqbalance reads the stats from /sys/class/net/ethX/statistics causing the
mutex to be locked to read the Phy half-duplex statistics registers.

The mutex was originally introduced to prevent concurrent accesses of
resources (the NVM and Phy) shared by the driver, firmware and hardware
a few years back when there was an issue with the NVM getting corrupted.
It was later split into two mutexes - one for the NVM and one for the Phy
when it was determined the NVM, unlike the Phy, should not be protected by
the software/firmware/hardware semaphore (arbitration of which is done in
part with the SWFLAG bit in the EXTCNF_CTRL register).  This latter
semaphore should be sufficient to prevent resource contention of the Phy in
the driver (i.e. the mutex for Phy accesses is not needed), but to be sure
the mutex is replaced with an atomic bit flag which will warn if any
contention is possible.

Also add additional debug output to help determine when the sw/fw/hw
semaphore is owned by the firmware or hardware.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Reported-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>

The recent changes to only power the device when the interface up
introduced a bug: changing interface type, legal when the interface
is down, performs device I/O.

Fix this functionality by validating and recording the interface
type when the change is requested, but only applying the change
if/when the interface is brought up.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Only station flags that are already defined in nl80211 are added for
now.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reuse the already existing struct nl80211_sta_flag_update to specify
both, a flag mask and the flag set itself. This means
nl80211_sta_flag_update is now used for setting station flags and also
for getting station flags.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The queue mapping/TID for non-QoS null data
responses to is never set, making it default
to BK. Fix that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Renamed to be in sync with Marketing term and to avoid
confusion with other chip names.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The AR946/8x chips are 2x2 Dual band with BT support. In order
to avoid misleading with other chips and to be in sync with
marketing team's term, AR9480 is renamed as AR9462.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Support the fast channel change across band switch only when there
are available of reusable cabliration results. And also observed that
doing agc control calibration on fastcc, sometimes causing calibration
timeout. Hence changing agc control to be run only on full chip reset.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Supported calibrations of radio retention table (RTT) are
	- DC offset
	- Filter
	- Peak detect
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To improve sensitivity for AR9480, the normal and minimum
noise floor values of both bands are updated.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k_hw: Improve fast channel change for AR9003 chips"
fixes the fast channel change issue for AR9003 chips that was
originally observed in AR9382 chip. Hence enabling fastcc support
again for 11A channel for AR9003 chips.

Cc: Paul Stewart <pstew@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently Tx IQ calibration is enabled by default for all AR9003
chips. But for AR9480, the calibration status should be read from
chip after processing ini. And also the carrier leak calibration
status is checked during init cal. As the init_cal is being called
for fast channel change too, the tx_cl status only be read after
full reset. Hence moving that into process ini function.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support to reuse Carrier leak calibration
during fast channel change for AR9480 chips.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Pass an argument to decide whether to reuse the Tx IQ
calibration measurements or not during fast channel change.
This will be later used by MCI support for AR9480.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to reduce the overall scan time, fast channel change
should be implemented properly. This patch adds fast channel
change support across band switch or channel mode switch
instead of doing full chip reset. During the fastcc, tx iqcal
measurements are preserved and will be reloaded after successful
the channel change.

This patch also addressed fast channel issue where the STA can not
see APs in higher than operating channel on 5GHz band after
the association.

Cc: Paul Stewart <pstew@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 5G Tx gain table w/ XPA is updated to improve spur
performance in high_power Tx gain table.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ar9003 table is updated to increase XLNA BIAS
output driver strengh.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Because of not clearing Bit 14 of AR_WA, the ASPM L1 is not
enabled when entering into sleep mode. AR9480 does not need
bit 14 to be set.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch takes care of warnings found by running
'make namespacecheck':

1. Remove dead code.
2. Reorder function definitions to avoid forward declarations.
3. Remove unnecessary function/structure declarations and mark
   them as static.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently global wait condition (adapter->cmd_wait_q.condition)
is used while sending synchronous commands to FW. When two threads
enter in mwifiex_send_cmd_sync() routine at the same time, both the
threads wait for their command responses. Since wait condition is
same for both, they wake up simultaneously after getting response
of 1st command. After this when a thread is waiting for command
response of 3rd command, it wakes up after getting response of 2nd
command and so on. Therefore we don't wait for the response of last
command(0xaa) during unload. Hence while next time loading the driver
command time out is seen for INIT command.

This problem is resolved by having separate wait condition flag for
each command(except scan command). Since scan command is treated
differently (by maintaining scan pending q etc.), newly defined flag
(scan_wait_q_woken) is used as a scan wait condition.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>