There's no good reason why this should be an SRIOV-only thing.
Thus, also move it out of SRIOV-specific files.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for some ethtool methods: get/set link settings, get/set
message level, get statistics, get link status, get ring params, get
pause params, and restart autonegotiation.

The code to collect the hardware statistics is moved into its own
function so that it can be used by "get statistics" method.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is based on public datasheet for sh7763 which shows it has the
same behavior and registers for WoL as other versions of sh_eth.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is based on public datasheet for sh7734 which shows it has the
same behavior and registers for WoL as other versions of sh_eth.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Geert Uytterhoeven reported WoL worked on his Armadillo board.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tested on Gen2 r8a7791/Koelsch.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add generic functionality to support Wake-on-LAN using MagicPacket which
are supported by at least a few versions of sh_eth. Only add
functionality for WoL, no specific sh_eth versions are marked to support
WoL yet.

WoL is enabled in the suspend callback by setting MagicPacket detection
and disabling all interrupts expect MagicPacket. In the resume path the
driver needs to reset the hardware to rearm the WoL logic, this prevents
the driver from simply restoring the registers and to take advantage of
that sh_eth was not suspended to reduce resume time. To reset the
hardware the driver closes and reopens the device just like it would do
in a normal suspend/resume scenario without WoL enabled, but it both
closes and opens the device in the resume callback since the device
needs to be open for WoL to work.

One quirk needed for WoL is that the module clock needs to be prevented
from being switched off by Runtime PM. To keep the clock alive the
suspend callback need to call clk_enable() directly to increase the
usage count of the clock. Then when Runtime PM decreases the clock usage
count it won't reach 0 and be switched off.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This bit was wrongly named due to a typo, Sergei checked the SH7734/63
manuals and this bit should be named MPDE.
Suggested-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have properly encapsulated and made drivers utilize exported
functions, we can switch dsa_switch_ops to be a annotated with const.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for making struct dsa_switch_ops const, encapsulate it
within a dsa_switch_driver which has a list pointer and a pointer to
dsa_switch_ops. This allows us to take the list_head pointer out of
dsa_switch_ops, which is written to by {un,}register_switch_driver.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Utilize the b53 exported functions to fill our bcm_sf2_ops structure,
also making it clear what we utilize and what we specifically override.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for making dsa_switch_ops const, export b53 operations
utilized by other drivers such as bcm_sf2.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 'struct sh_eth_cpu_data' field indicating the "intelligent checksum"
support was misnamed 'hw_crc' -- rename it to 'hw_checksum'.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After checking all  the available manuals,  I have enough information to
conclude  that the 'shift_rd0' flag is only relevant  for the Ether cores
supporting so called "intelligent checksum" (and hence having CSMR) which
is indicated  by the 'hw_crc' flag.  Since  all the relevant SoCs now have
both these flags set, we can  at last  get  rid of the former flag...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While in RUNNING state, phy_state_machine() checks for link changes by
comparing phydev->link before and after calling phy_read_status().
This works as long as it is guaranteed that phydev->link is never
changed outside the phy_state_machine().

If in some setups this happens, it causes the state machine to miss
a link loss and remain RUNNING despite phydev->link being 0.

This has been observed running a dsa setup with a process continuously
polling the link states over ethtool each second (SNMPD RFC-1213
agent). Disconnecting the link on a phy followed by a ETHTOOL_GSET
causes dsa_slave_get_settings() / dsa_slave_get_link_ksettings() to
call phy_read_status() and with that modify the link status - and
with that bricking the phy state machine.

This patch adds a fail-safe check while in RUNNING, which causes to
move to CHANGELINK when the link is gone and we are still RUNNING.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new glue driver called dwmac-dwc-qos-eth which
was based in the dwc_eth_qos as is. To assure retro-compatibility a slight
tweak was also added to stmmac_platform.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Tested-by: NNiklas Cassel <niklas.cassel@axis.com>
Reviewed-by: NLars Persson <larper@axis.com>
Acked-by: NAlexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to the
plat_stmmacenet_data structure. It also moves these platform variables
initialization to stmmac_platform. This was done for two reasons:

a) If PCI is used, platform related code is being executed in stmmac_main
resulting in warnings that have no sense and conceptually was not right

b) stmmac as a synopsys reference ethernet driver stack will be hosting
more and more drivers to its structure like synopsys/dwc_eth_qos.c.
These drivers have their own DT bindings that are not compatible with
stmmac's. One of the most important are the clock names, and so they need
to be parsed in the glue logic and initialized there, and that is the main
reason why the clocks were passed to the platform structure.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Tested-by: NNiklas Cassel <niklas.cassel@axis.com>
Reviewed-by: NLars Persson <larper@axis.com>
Acked-by: NAlexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new parameter to the stmmac DT: snps,en-tx-lpi-clockgating.
It was ported from synopsys/dwc_eth_qos.c and it is useful if lpi tx clock
gating is needed by stmmac users also.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Tested-by: NNiklas Cassel <niklas.cassel@axis.com>
Reviewed-by: NLars Persson <larper@axis.com>
Acked-by: NAlexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code to handle rx checksumming was in the driver since its introduction
but for reasons unknown the feature flag was left out. Now it is possible
to enable this feature with ethtool.

Tested on my AR8161 ethernet card, there are no regressions observed in
netperf if this feature is enabled.
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As ENOTSUPP is specific to NFS, change the return error value to
EOPNOTSUPP in various places in the mlxsw driver.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the order of the free directives to match the port init function
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the mlxsw spectrum driver only supports offloading the matchall
classifier together with the mirred action. To allow more matchall tc
offloads, make the code symmetric so that it can be easily extended later
on for other actions.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Probably some copy-paste error from "int_msix" that caused "int_" prefix to
appear in the comments for all "eq_" APIs.
Signed-off-by: NElad Raz <eladr@mellanox.com>
Acked-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "err" variable is been checked, return always 0.
Signed-off-by: NElad Raz <eladr@mellanox.com>
Acked-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NVadim Pasternak <vadimp@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow to set number of descs close to possible values. In case of
minimum limit it's equal to number of channels to be able to set
at least one desc per channel. For maximum limit leave enough descs
number for tx channels.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Activate 4K UAR support for firmware versions that support it.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add fields to structs to convey to kernel an indication whether the
library supports multi UARs per page and return to the library the size
of a UAR based on the queried value.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Current check requests that new fields in struct
mlx5_ib_alloc_ucontext_req_v2 that are not known to the driver be zero.
This was introduced so new libraries passing additional information to
the kernel through struct mlx5_ib_alloc_ucontext_req_v2 will be notified
by old kernels that do not support their request by failing the
operation. This schecme is problematic since it requires libmlx5 to issue
the requests with descending input size for struct
mlx5_ib_alloc_ucontext_req_v2.

To avoid this, we require that new features that will obey the following
rules:
If the feature requires one or more fields in the response and the at
least one of the fields can be encoded such that a zero value means the
kernel ignored the request then this field will provide the indication
to the library. If no response is required or if zero is a valid
response, a new field should be added that indicates to the library
whether its request was processed.

Fixes: b368d7cb ('IB/mlx5: Add hca_core_clock_offset to udata in init_ucontext')
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Make use of the blue flame registers allocator at mlx5_ib. Since blue
flame was not really supported we remove all the code that is related to
blue flame and we let all consumers to use the same blue flame register.
Once blue flame is supported we will add the code. As part of this patch
we also move the definition of struct mlx5_bf to mlx5_ib.h as it is only
used by mlx5_ib.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

A reference to a UAR is required to generate CQ or EQ doorbells. Since
CQ or EQ doorbells can all be generated using the same UAR area without
any effect on performance, we are just getting a reference to any
available UAR, If one is not available we allocate it but we don't waste
the blue flame registers it can provide and we will use them for
subsequent allocations.
We get a reference to such UAR and put in mlx5_priv so any kernel
consumer can make use of it.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are implementing a MDIO bus which is behind another one, so use the
nested version of the accessors to get lockdep annotations correct.

Fixes: 461cd1b0 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We make the bcm_sf2 driver override ds->ops which points to
b53_switch_ops since b53_switch_alloc() did the assignent. This is all
well and good until a second b53 switch comes in, and ends up using the
bcm_sf2 operations. Make a proper local copy, substitute the ds->ops
pointer and then override the operations.

Fixes: f458995b ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tc_from field fulfills two roles. It encodes whether a packet was
redirected by an act_mirred device and, if so, whether act_mirred was
called on ingress or egress. Split it into separate fields.

The information is needed by the special IFB loop, where packets are
taken out of the normal path by act_mirred, forwarded to IFB, then
reinjected at their original location (ingress or egress) by IFB.

The IFB device cannot use skb->tc_at_ingress, because that may have
been overwritten as the packet travels from act_mirred to ifb_xmit,
when it passes through tc_classify on the IFB egress path. Cache this
value in skb->tc_from_ingress.

That field is valid only if a packet arriving at ifb_xmit came from
act_mirred. Other packets can be crafted to reach ifb_xmit. These
must be dropped. Set tc_redirected on redirection and drop all packets
that do not have this bit set.

Both fields are set only on cloned skbs in tc actions, so original
packet sources do not have to clear the bit when reusing packets
(notably, pktgen and octeon).
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract the remaining two fields from tc_verd and remove the __u16
completely. TC_AT and TC_FROM are converted to equivalent two-bit
integer fields tc_at and tc_from. Where possible, use existing
helper skb_at_tc_ingress when reading tc_at. Introduce helper
skb_reset_tc to clear fields.

Not documenting tc_from and tc_at, because they will be replaced
with single bit fields in follow-on patches.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packets sent by the IFB device skip subsequent tc classification.
A single bit governs this state. Move it out of tc_verd in
anticipation of removing that __u16 completely.

The new bitfield tc_skip_classify temporarily uses one bit of a
hole, until tc_verd is removed completely in a follow-up patch.

Remove the bit hole comment. It could be 2, 3, 4 or 5 bits long.
With that many options, little value in documenting it.

Introduce a helper function to deduplicate the logic in the two
sites that check this bit.

The field tc_skip_classify is set only in IFB on skbs cloned in
act_mirred, so original packet sources do not have to clear the
bit when reusing packets (notably, pktgen and octeon).
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>