The RATR register is used to configure the Router Adjacency (next-hop)
Table.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a very simple manager for KVD linear area. Currently, the
allocator will either allocate a single entry from pre-defined sub-area,
or in case more than one entry is needed, it will allocate 32-entry chunk
in other pre-defined sub-area.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Override the defaults and define the area sizes ourselves.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now we only used hash-based tables in the device, but we are
going to use the linear table for remote routes adjacency lists.

Add the configuration fields that control the size of the linear table.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Listen to any NEIGH_UPDATE events sent and program the device
accordingly. If NUD state is VALID and neighbour isn't yet offloaded,
then program it into the device's table. Otherwise, just edit its
parameters.

If NUD state machine transitioned neighbour out of VALID state and it's
present in the device's table, then remove it.

Note that the device is programmed in delayed work, as the netevent
notification chain is atomic and prevents us from going to sleep.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As previously explained, the driver should periodically poll the device
for neighbours activity according to the configured DELAY_PROBE_TIME.
This will prevent active neighbours from staying in STALE state for long
periods of time.

During init configure the polling interval according to the
DELAY_PROBE_TIME used in the default table. In addition, register a
netevent notification block, so that the interval is updated whenever
DELAY_PROBE_TIME changes.

Using the computed interval schedule a delayed work, which will update
the kernel via neigh_event_send() on any active neighbour since the last
delayed work.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RAUHTD register allows dumping entries from the Router Unicast Host
Table.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RAUHT register is used to configure and query the Unicast Host Table
in devices that implement the Algorithmic LPM. In other words, it is
used to configure neighbour entries in the device.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to hold some private data for every neigh entry. It would be
possible to do it using neigh_priv_len/ndo_neigh_construct/
ndo_neigh_destroy however only for the port device itself. That would not
work for stacked devices like bridge/team/bond. So introduce a private
neigh table. Hook onto ndos neigh_construct/destroy and add/remove
table entry according to that.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just like per prio counters, the global flow counters are queried from
per priority counters register.
Global flow control counters are stored in priority 0 PFC counters.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the needed descriptors to expose RoCE RDMA counters.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enhance the existing get_rxnfc callback:
1. Get flow rule of specific ID.
2. Get all flow rules.
3. Get number of rules.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to add flow steering rules with ethtool
of L3/L4 flow types (ip4/tcp4/udp4).
Those rules will be in higher priority than l2 flow rules, in order
to prefer more specific rules.

Mask is not supported for l3/l4 flow types.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement etrhtool set_rxnfc callback to support ethtool flow spec
direct steering. This patch adds only the support of ether flow type
spec. L3/L4 flow specs support will be added in downstream patches.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of explicitly cleaning up the well known parts of the steering
tree, we use the generic tree structure to traverse for cleanup.
No functional changes.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of having all steering private name spaces and
steering module fields flat in mlx5_core_priv, we wrap
them in mlx5_flow_steering for better modularity and
API exposure.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce the set of arguments passed to mlx5_add_flow_rule
by introducing flow_spec structure.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As with the previously introduced L3 interfaces, listen to 'inetaddr'
notifications sent for bridges devices configured on top of the port
netdevs and create / destroy router interfaces (RIFs) accordingly.
This also includes VLAN devices configured on top of the VLAN-aware
bridge.

The RIFs will be destroyed either when the last IP address is removed or
when the underlying FID is is destroyed.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before introducing support for L3 interfaces on top of the VLAN-aware
bridge we need to add some missing infrastructure.

Such an interface can either be the bridge device itself or a VLAN
device on top of it. In the first case the router interface (RIF) is
associated with FID 1, which is created whenever the first port netdev
joins the bridge. We currently assume the default PVID is 1 and that
it's already created, as it seems reasonable. This can be extended in
the future.

However, in the second case it's entirely possible we've yet to create a
matching FID. This can happen if the VLAN device was configured before
making any bridge port member in the VLAN.

Prevent such ordering problems by using the VLAN device's CHANGEUPPER
event to configure the FID. Make the VLAN device hold a reference to the
FID and prevent it from being destroyed even if none of the port netdevs
is using it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previous commit deprecated the vFIDs used to get traffic to the CPU
('port_vfids'). Thus, we now use the vFIDs as god intended and the
artificial split is no longer needed.

Rename functions and variables to reflect that.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now we only supported bridged interfaces. Packets ingressing
through the switch ports were either classified to FIDs (in the case of
the VLAN-aware bridge) or vFIDs (in the case of VLAN-unaware bridges).
The packets were then forwarded according to the FDB. Routing was done
entirely in slowpath, by splitting the vFID range in two and using the
lower 0.5K vFIDs as dummy bridges that simply flooded all incoming
traffic to the CPU.

Instead, allow packets to be routed in the device by creating router
interfaces (RIFs) that will direct them to the router block.
Specifically, the RIFs introduced here are Sub-port RIFs used for VLAN
devices and port netdevs. Packets ingressing from the {Port / LAG ID, VID}
with which the RIF was programmed with will be assigned to a special
kind of FIDs called rFIDs and from there directed to the router.

Create a RIF whenever the first IPv4 address was programmed on a VLAN /
LAG / port netdev. Destroy it upon removal of the last IPv4 address.
Receive these notifications by registering for the 'inetaddr'
notification chain. A non-zero (10) priority is used for the
notification block, so that RIFs will be created before routes are
offloaded via FIB code.

Note that another trigger for RIF destruction are CHANGEUPPER
notifications causing the underlying FID's reference count to go down to
zero. This can happen, for example, when a VLAN netdev with an IP address
is put under bridge. While this configuration doesn't make sense it does
cause the device and the kernel to get out of sync when the netdev is
unbridged. We intend to address this in the future, hopefully in current
cycle.

Finally, Remove the lower 0.5K vFIDs, as they are deprecated by the RIFs,
which will trap packets according to their DIP.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are just about to introduce router interfaces (RIFs), but before that
we need to be able update the device with the correct RIF attributes
whenever they change for the netdev the RIF is backing. Two such
attributes are MTU and MAC.

The MAC is used both to set the source MAC of packets egressing from the
RIF and also to program an FDB rule that will direct packets to the
router block.

Use the existing netdevice notification block and respond to CHANGEADDR
and CHANGEMTU accordingly. Store both attributes in the RIF struct
in case we need to revert to old attributes following a failed update.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add functions that iterate over lower devices and find port device.
As a dependency add netdev_for_each_all_lower_dev and
netdev_for_each_all_lower_dev_rcu macro with
netdev_all_lower_get_next and netdev_all_lower_get_next_rcu shelpers.

Also, add functions to return mlxsw struct according to lower device
found and mlxsw_port struct with a reference to lower device.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ipv4 FIB entries addition and removal. Initially, we support
local and broadcast routes using "ip2me" trap action.
Also, unicast routes without nexthop are supported using "local" action.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Serves for adding, updating and removing fib entries.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Virtual router is a construct used inside HW. In this implementation
we map kernel tables to virtual routers one to one. Introduce management
logic to create virtual routers when needed and destroy in case they are
no longer in use. According to that, call into LPM tree management.
Each virtual router is always bound to one LPM tree.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce basic LPM tree management allowing to share the trees in
between tables if the used prefixes in the tables are the same.
Build the tree structure according to the used prefixes. Although it is
not optimal for many use cases, this initial implementation does only
simple linear left-tree. More advanced structures will be introduced
later on, possibly including mechanisms to change trees on the fly.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This register is used to bind virtual router and protocol to an
allocated LPM tree.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Serves to build LPM tree structure.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register serves for allocation and deallocation of LPM search tree.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shadow FIB is needed in order to hold additional information for FIB
entries and keep track of used prefixes. That is needed for the LPM tree
construction to be introduced later on in this set.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Silent a few smatch warnings about indentation.
This include the removal of a 'return' statement in 'resource_tracker.c'.
This 'return' will still be performed when breaking out of the
corresponding 'switch' block.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip2me:
To instruct HW to send trapped ip2me traffic to kernel, we have to add
this trap. Selection ip2me traffic is introduced later on in this set.

ARPs:
We are going to stop flooding to CPU port when netdev isn't bridged and
only get packets destined to the netdev's IP address and certain control
packets.

Add traps for ARP request (broadcast) and response (unicast) in order to
get these to the CPU and resolve neighbours.

host miss:
If a packet is routed through a directly connected route and its
destination IP is not in the device's neighbour table, then we need to
trap it to CPU. This will cause the host to resolve the MAC of the
neighbour, which will be eventually programmed to the device's table.

router ingress:
In order to trap packets in router part.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When removing packet traps we should use action 'discard' instead of
'forward', as some trap IDs we'll add cannot be configured with the
later. However, result is the same, as packets are not trapped to the
CPU.

In the future we will be able to reverse the operation properly by
detaching the trap group from the CPU.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the Router Interface Table Register (RITR), which allows us to
create and configure router interfaces (RIFs).
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Incoming packets are directed to the router when they match an FDB
entry with action forward to IP router.

Add this action, which was mistakenly named "TRAP".
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When enabling the router in the device we will represent L3 netdevs
using router interfaces (RIFs). These will be specified whenever
programming routes or neighbours on the netdev.

Introduce the basic RIF infrastructure which allows one to lookup a RIF
by its netdev. Later patches in the series will extend this, but the
basic routines are needed now in order to direct traffic to CPU.

Pointers to the RIF structs are stored in an array indexed by the RIF's
number. This will allow us to efficiently update the kernel's neighbour
table when regularly dumping the device's table.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create a skeleton router file and do basic HW initialization of router.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During ports initialization a net device is registered for each
available port, which implies the port is usable. However, a port is
only usable after the different parts of the device (e.g. flooding,
buffers) are initialized. This is especially important now, when we must
initialize the router before the ports, as otherwise the device can't be
initialized.

Solve that by initializing the switch ports at the end of init sequence.

Also, remove an unnecessary warning about port up/down events, which
would otherwise be invoked whenever removing the driver, as ports are
removed before unregistering the listener for these events.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the Router General Configuration Register (RGCR), which allows us to
enable the router in the device and configure its various parameters.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>