Since commit 412ca155 ("macvlan: Move broadcasts into a work queue"), the
driver uses tx_queue_len of the master device as the limit of packets enqueuing.
Problem is that virtual drivers have this value set to 0, thus all broadcast
packets were rejected.
Because tx_queue_len was arbitrarily chosen, I replace it with a static limit
of 1000 (also arbitrarily chosen).

CC: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: NThibaut Collet <thibaut.collet@6wind.com>
Suggested-by: NThibaut Collet <thibaut.collet@6wind.com>
Tested-by: NThibaut Collet <thibaut.collet@6wind.com>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following randconfig build failure:

> drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c: In function
> ‘pch_ptp_match’:
> drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c:130:2: error:
> implicit declaration of function ‘ptp_classify_raw’
> [-Werror=implicit-function-declaration]
>   if (ptp_classify_raw(skb) == PTP_CLASS_NONE)
>   ^
> cc1: some warnings being treated as errors
> make[5]: *** [drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.o] Error 1
Reported-by: NJim Davis <jim.epost@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LIBFC depends upon SCSI_FC_ATTRS and select's CRC32C.

The only alternative would be to 'select' CRC32C and all of
SCSI_FC_ATTRS direct and indirect dependencies in the Kconfig section
for every LIBFCOE user which makes little sense.

Subsequently, use 'depends' instead of 'select' for LIBFCOE too.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
pull-request: can 2014-09-18

this is a pull request of 8 patches for current net.

A patch by Roger Quadros for the c_can driver fixes the swapped parameters of
the c_can_hw_raminit_ti() function. Oliver Hartkopp adds the missing PCI ids to
the peak_pci driver to support the single channel PCAN ExpressCard 34 adapter.
David Dueck converts the at91_can driver to use proper clock handling
functions. Then there are 5 patches by David Jander and me which fix several
mailbox related problems in the flexcan driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit fb5d1e9e ("openvswitch: Build flow cmd netlink reply only if needed."),
the new flows are not notified to the listeners of OVS_FLOW_MCGROUP.

This commit fixes the problem by using the genl function, ie
genl_has_listerners() instead of netlink_has_listeners().
Signed-off-by: NSamuel Gauthier <samuel.gauthier@6wind.com>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function is the counterpart of the function netlink_has_listeners().
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

linux/log2.h was included twice.
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I cannot move a macvlan interface created on top of a bonding interface
to a different namespace:

% ip netns add dummy0
% ip link add link bond0 mac0 type macvlan
% ip link set mac0 netns dummy0
RTNETLINK answers: Invalid argument
%

The problem seems to be that commit f9399814 ("bonding: Don't allow
bond devices to change network namespaces.") sets NETIF_F_NETNS_LOCAL
on bonding interfaces, and commit 797f87f8 ("macvlan: fix netdev
feature propagation from lower device") causes macvlan interfaces
to inherit its features from the lower device.

NETIF_F_NETNS_LOCAL should not be inherited from the lower device
by a macvlan.
Patch tested on 3.16.
Signed-off-by: NFrancesco Ruggeri <fruggeri@arista.com>
Acked-by: NCong Wang <cwang@twopensource.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

John W. Linville says:

====================
pull request: wireless 2014-09-17

Please pull this batch of fixes intended for the 3.17 stream...

Arend van Spriel sends a trio of minor brcmfmac fixes, including a
fix for a Kconfig/build issue, a fix for a crash (null reference),
and a regression fix related to event handling on a P2P interface.

Hante Meuleman follows-up with a brcmfmac fix for a memory leak.

Johannes Stezenbach brings an ath9k_htc fix for a regression related
to hardware decryption offload.

Marcel Holtmann delivers a one-liner to properly mark a device ID
table in rfkill-gpio.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recently aded the use of skb_frag_dma_map to 3c59x, but didn't realize it
automatically included the frag_offset internally, as well as provided an option
to specify an extra offset in the parameter list.  We need to specify an offset
of 0 in the parameter list to avoid skb corruption that results in lost
connections.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Linux Kernel list <linux-kernel@vger.kernel.org>
CC: "David S. Miller" <davem@davemloft.net>
CC: Meelis Roos <mroos@linux.ee>
Tested-by: NMeelis Roos <mroos@linux.ee>

Noted that 3c59x has no checks on transmit for failed DMA mappings, and no
ability to unmap fragments when a single map fails in the middle of a transmit.
This patch provides error checking to ensure that dma mappings work properly,
and unrolls an skb mapping if a fragmented skb transmission has a mapping
failure to prevent leaks.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Linux Kernel list <linux-kernel@vger.kernel.org>
CC: "David S. Miller" <davem@davemloft.net>
CC: Meelis Roos <mroos@linux.ee>
Tested-by: NMeelis Roos <mroos@linux.ee>

fix several issues in sparc BPF JIT compiler.

ldx/stx related:
. classic BPF instructions that access mem[] slots were not setting
  SEEN_MEM flag, so stack wasn't allocated. Fix that by advertising
  correct flags

. LDX/STX instructions were missing SEEN_XREG, so register value
  could have leaked to user space. Fix it.

. since stack for mem[] slots is allocated with 'sub %sp' instead
  of 'save %sp', use %sp as base register instead of %fp.

. ldx mem[0] means first slot in classic BPF which should have
  -4 offset instead of 0.

. sparc64 needs 2047 stack bias as per ABI to access stack

. emit_stmem() was using LD32I macro instead of ST32I

SKF_AD_VLAN_TAG* related:
. SKF_AD_VLAN_TAG_PRESENT must return 1 or 0 instead of '> 0' or 0
  as per classic BPF de facto standard

. SKF_AD_VLAN_TAG needs to mask the field correctly

Fixes: 2809a208 ("net: filter: Just In Time compiler for sparc")
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to make the driver work with the common clock framework, this patch
converts the clk_enable()/clk_disable() to
clk_prepare_enable()/clk_disable_unprepare(). While there, add the missing
error handling.
Signed-off-by: NDavid Dueck <davidcdueck@googlemail.com>
Signed-off-by: NAnthony Harivel <anthony.harivel@emtrion.de>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch increases the mask in the FLEXCAN_MCR_MAXMB() to 7 bits as in the
newer flexcan cores the MAXMB field is 7 bits wide.
Reported-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

After sending a RTR frame the TX mailbox becomes a RX_EMPTY mailbox. To avoid
side effects when the RX-FIFO is full, this patch puts the TX mailbox into
TX_INACTIVE mode in the transmission complete interrupt handler. This, of
course, leaves a race window between the actual completion of the transmission
and the handling of tx-complete interrupt. However this is the best we can do
without busy polling the tx complete interrupt.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch implements the workaround mentioned in ERR005829:

    ERR005829: FlexCAN: FlexCAN does not transmit a message that is enabled to
    be transmitted in a specific moment during the arbitration process.

Workaround: The workaround consists of two extra steps after setting up a
message for transmission:

Step 8: Reserve the first valid mailbox as an inactive mailbox (CODE=0b1000).
If RX FIFO is disabled, this mailbox must be message buffer 0. Otherwise, the
first valid mailbox can be found using the "RX FIFO filters" table in the
FlexCAN chapter of the chip reference manual.

Step 9: Write twice INACTIVE code (0b1000) into the first valid mailbox.
Signed-off-by: NDavid Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Apparently mailboxes may contain random data at startup, causing some of them
being prepared for message reception. This causes overruns being missed or even
confusing the IRQ check for trasmitted messages, increasing the transmit
counter instead of the error counter.

This patch initializes all mailboxes after the FIFO as RX_INACTIVE.
Signed-off-by: NDavid Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the initialization of the TX mailbox. It is now correctly
initialized as TX_INACTIVE not RX_EMPTY.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Add PCI ID definition for the single channel PCAN ExpressCard 34 adapter. Due
to the subsystem id evaluation the correct number of channels (here 1) is
created at initialization time. Tested including the LED functionality.
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Pass the correct 'mask' and 'value' bits to c_can_hw_raminit_wait_ti(). They
seem to have been swapped in the usage instances.
Reported-by: NJay Schroeder <jay.schroeder@garmin.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There are other kconfig symbols which use SCSI_FC_ATTRS.
In order to maintain sanity and prevent kconfig warnings, change
all of these from using 'select' to using 'depends on' so that
proper symbol dependencies will be honored and circular depends
problems will be avoided.
This fixes kconfig warnings and build errors:

warning: (LIBFC && SCSI_IBMVFC && SCSI_QLA_FC && SCSI_LPFC && ZFCP && SCSI_BFA_FC && SCSI_CHELSIO_FCOE && FUSION_FC) selects SCSI_FC_ATTRS which has unmet direct dependencies (SCSI && NET)
drivers/scsi/scsi_transport_fc.c: In function 'fc_host_post_event':
drivers/scsi/scsi_transport_fc.c:543:7: error: 'scsi_nl_sock' undeclared (first use in this function)
drivers/scsi/scsi_transport_fc.c: In function 'fc_host_post_vendor_event':
drivers/scsi/scsi_transport_fc.c:611:7: error: 'scsi_nl_sock' undeclared (first use in this function)

Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported by Nikolay Aleksandrov.  In efx_init_port() we call
 efx_mac_reconfigure() to work around a Falcon/A1 limitation, and this calls
 efx_{arch}_filter_sync_rx_mode(), which takes the addr_list_lock; but this
 lock is uninitialised, because we haven't called register_netdevice() yet.
So, in efx_farch_filter_sync_rx_mode(), check efx_dev_registered() before
 doing anything else.
The EF10 equivalent, efx_ef10_filter_sync_rx_mode(), already has the
 corresponding check.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Tested-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the ACPI based switches the MODULE_DEVICE_TABLE is missing to
export the entries for module auto-loading.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the "changed" test in __rtl8169_set_features(). Instead, do
simple test in rtl8169_set_features().

Set the RxChkSum and RxVlan through __rtl8169_set_features() in
rtl_open().
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix build errors when CONFIG_SCSI_NETLINK is enabled but
CONFIG_NET is not enabled:

drivers/built-in.o: In function `scsi_nl_rcv_msg':
scsi_netlink.c:(.text+0x1850fa): undefined reference to `netlink_ack'
scsi_netlink.c:(.text+0x185105): undefined reference to `skb_pull'
scsi_netlink.c:(.text+0x18515d): undefined reference to `netlink_capable'
drivers/built-in.o: In function `scsi_netlink_init':
(.text+0x185244): undefined reference to `init_net'
drivers/built-in.o: In function `scsi_netlink_init':
(.text+0x185258): undefined reference to `__netlink_kernel_create'
drivers/built-in.o: In function `scsi_netlink_exit':
(.text+0x185291): undefined reference to `netlink_kernel_release'
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Tested-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Anish Bhatt says:

====================
net: Fix randconfig errros in bnx2i/bnx2fc caused by IPV6

Just like CNIC bnx2i/bnx2fc also have their tristate dependent on IPV6, however
using the same solution as CNIC can cause recursive dependecies during make.

Based on suggestions by Randy Dunlap, SCSI_NETLINK now depends on NET instead
 of selecting NET. Second patch fixes the actual randconfig error.

Entire thread can be followed here : https://lkml.org/lkml/2014/9/9/500

Fixes: c99d667e ("cnic : Cleanup CONFIG_IPV6 & VLAN check")
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just like CNIC, tristate of these two modules is also dependent on IPV6.
These need to be handled separately as they select CNIC, which can override
tristate for CNIC from 'm' to 'y', which can cause build failures when ipv6 is
 compiled as a module even if CNIC's Kconfig will only 'm' or 'n' when ipv6 is
compiled as a module.

Fixes: c99d667e ("cnic : Cleanup CONFIG_IPV6 & VLAN check")
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Required for avoiding recursive dependencies in the Kconfig, brought out
by fixing randconfig error for bnx2i/bnx2fc in the patch that follows.
As suggested by Randy Dunlap
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 35b1de55 ("rdma/cxgb4: Fixes cxgb4 probe failure in VM when PF is
exposed through PCI Passthrough") moved the code to check for SR-IOV PF[0..3]
much further down in init_one() past the point where we allocate a (struct
adapter) for PF[0..3]. As a result, we left four of these on ever module remove.

Fix: Allocate adapter structure only for PF4
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As Toshiaki Makita pointed out, the BRIDGE_INPUT_SKB_CB will
not be initialized in br_should_learn() as that function
is called only from br_handle_local_finish().  That is
an input handler for link-local ethernet traffic so it perfectly
correct to check br->vlan_enabled here.

Reported-by: Toshiaki Makita<toshiaki.makita1@gmail.com>
Fixes: 20adfa1a bridge: Check if vlan filtering is enabled only once.
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In v3.15 the driver stopped to accept network packets after successful
authentification, which could be worked around by passing the
nohwcrypt=1 module parameter.  This was not reproducible by
everyone, and showed random behaviour in some tests.
It was caused by an uninitialized variable introduced
in 4ed1a8d4 ("ath9k_htc: use ath9k_cmn_rx_accept") and
used in 341b29b9 ("ath9k_htc: use ath9k_cmn_rx_skb_postprocess").

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=78581
Fixes: 341b29b9 ("ath9k_htc: use ath9k_cmn_rx_skb_postprocess")
Signed-off-by: NJohannes Stezenbach <js@sig21.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware notifies about interface changes through the IF event
which has a NO_IF flag that means host can ignore the event. This
behaviour was introduced in the driver by:

  commit 2ee8382f
  Author: Arend van Spriel <arend@broadcom.com>
  Date:   Sat Aug 10 12:27:24 2013 +0200

      brcmfmac: ignore IF event if firmware indicates it

It turns out that the IF event for the P2P_DEVICE also has this
flag set, but the event should not be ignored in this scenario.
The mentioned commit caused a regression in 3.12 kernel in creation
of the P2P_DEVICE interface.

Cc: <stable@vger.kernel.org> # 3.14, 3.16
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For P2P_DEVICE interface the function brcmf_cfg80211_update_proto_addr_mode()
resulted in a crash, because it assumed wdev->netdev would be valid. The
ifp should be obtained through the driver vif structure which contains the
wireless_dev.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The host-interface can select which protocol implementation it
needs. Selecting PCIe will include the msgbuf protocol and selecting
USB and/or SDIO will include the bcdc protocol. The PCIe kconfig
option assures the dependencies for msgbuf are met, ie. HAS_DMA.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function brcmf_enable_bw40_2g contains a memory leak. The
function is also missing initialisation of one of the members of
ch struct, which can lead to warning but this has no impact on
result.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

__netdev_adjacent_dev_insert may add adjust device of different net
namespace, without proper check it leads to emergence of broken
sysfs links from/to devices in another namespace.
Fix: rewrite netdev_adjacent_is_neigh_list macro as a function,
     move net_eq check into netdev_adjacent_is_neigh_list.
     (thanks David)
     related to: 4c75431aSigned-off-by: NAlexander Fomichev <git.user@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The KSZ9031 appears to suffer from the same hardware bug as described
for the KSZ9021 in commit 32fcafbc
("net/phy: micrel: Disable asymmetric pause for KSZ9021")
you have to unplug the cable and plug it back to get it to work.

Remove the SUPPORTED_Asym_Pause flag for the KSZ9031 to fix this.
Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vladislav Yasevich says:

====================
bridge: Two small fixes to vlan filtering code.

This series corrects 2 small issues that I've ran across recently
while doing more work with vlan filtering changes.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, it is possible to modify the vlan filter
configuration to add pvid or untagged support.
For example:
  bridge vlan add vid 10 dev eth0
  bridge vlan add vid 10 dev eth0 untagged pvid

The second statement will modify vlan 10 to
include untagged and pvid configuration.
However, it is currently impossible to go backwards
  bridge vlan add vid 10 dev eth0 untagged pvid
  bridge vlan add vid 10 dev eth0

Here nothing happens.  This patch correct this so
that any modifiers not supplied are removed from
the configuration.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bridge code checks if vlan filtering is enabled on both
ingress and egress.   When the state flip happens, it
is possible for the bridge to currently be forwarding packets
and forwarding behavior becomes non-deterministic.  Bridge
may drop packets on some interfaces, but not others.

This patch solves this by caching the filtered state of the
packet into skb_cb on ingress.  The skb_cb is guaranteed to
not be over-written between the time packet entres bridge
forwarding path and the time it leaves it.  On egress, we
can then check the cached state to see if we need to
apply filtering information.
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>