If LLD supports FCCRC offload, it should set ip_summed to be
CHECKSUM_UNNECESSARY so we don't have to do CRC check again.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This adds implementation of ddp_setup()/ddp_done() in fcoe_sw for its
fcoe_sw_libfc_fcn_templ.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

When LLD supports direct data placement (ddp) for large receive of an scsi
i/o coming into fc_fcp, we call into libfc_function_template's ddp_setup()
to prepare for a ddp of large receive for this read I/O. When I/O is complete,
we call the corresponding ddp_done() to get the length of data ddped as well
as to let LLD do clean up.

fc_fcp_ddp_setup()/fc_fcp_ddp_done() are added to setup and complete a ddped
read I/O described by the given fc_fcp_pkt. They would call into corresponding
ddp_setup/ddp_done implemented by the fcoe layer. Eventually, fcoe layer calls
into LLD's ddp_setup/ddp_done provided through net_device
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Change fcoe_xmit to setup gso for LLD LSO offload as well as CRC offload
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Make sure for large send is supported by LLD in outgoing FCP data, we are only
sending the lso_max a time in one single large send, since that is what
supported by LLD.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This checks if net_devices supports FCoE offload ops in netdev_ops and it
if it does, then sets up the corresponding flags in the associated fc_lport.

For large send offload, the maximum length supported in one large send is now
described by the added lso_max in fc_lport, which is setup initially from
netdev->gso_max_size.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This adds support to provide Fiber Channel over Ethernet (FCoE) offload
through net_device's net_device_ops struct. The offload through net_device
for FCoE is enabled in kernel as built-in or module driver.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Acked-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Add FC CRC offload check for ETH_P_FCOE.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Acked-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Define feature flags for FCoE offloads.
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NYi Zou <yi.zou@intel.com>
Acked-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Reclaim 8 upper bits of netdev->features from GSO.
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NYi Zou <yi.zou@intel.com>
Acked-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This adds eth type ETH_P_FCOE for Fibre Channel over Ethernet (FCoE),
consequently, the ETH_P_FCOE from fc_fcoe.h and fcoe skb->protocol
is not set as ETH_P_FCOE.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Acked-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] scsi_dh_rdac: Retry mode select for NO_SENSE, ABORTED_COMMAND, UNIT_ATTENTION, NOT_READY(02/04/01)

This patch is to add retry for mode select if mode select command is
returned with sense NO_SENSE, UNIT_ATTENTION, ABORTED_COMMAND,
NOT_READY(02/04/01). This patch reorganise the sense keys from if-else
to switch-case format for better maintainability.
Signed-off-by: NVijay Chauhan <vijay.chauhan@lsi.com>
Acked-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Report the fc_host_port_type as FC_PORTTYPE_NPIV when the subchannel
is running in NPIV mode. This allows to see the correct type with
lsscsi -H -t --list
Acked-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

A scheduled work might still be pending, running while the adapter is
in progress to get dequeued from the system. This can lead to an
invalid pointer dereference (Oops).  Once the adpater is set online
again, ensure the nameserver environment is initialized to the
appropriate values again.
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Ensure the refcounting is correct even if we were not able to
schedule a work. In addition we have to make sure no scheduled
work is pending while we're dequeing the adapter from the
systems environment.
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

It will not be necessary to set the erp failed status bit
in case a SCSI device is removed by the SCSI mid layer.
In the case a SCSI device is unavailable for a short time
(15 to 20 seconds) a FCP unit will not get on-line again.
Signed-off-by: NMartin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Use the I/O blocking mechanism in the FC transport class to allow
faster failovers for multipathing:
- Call fc_remote_port_delete early to set the rport to BLOCKED.
- Check the rport status in queuecommand with fc_remote_portchkready
  to no longer accept new I/O for this port and fail the I/O with the
  appropriate scsi_cmnd result.
- Implement the terminate_rport_io handler to abort all pending I/O
  requests
- Return SCSI commands with DID_TRANSPORT_DISRUPTED while erp is
  running.
- When updating the remote port status, check for late changes and
  update the remote ports status accordingly.
Acked-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

After an error condition resolved a remote storage port was never
re-opened. The incoming RSCN was not processed accordingly due
to a misinterpreted status flag / return value combination.
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The usage of the PCI flag to trigger interrupts is optional. Even
without setting the flag, qdio still receives interrupts to continue
working on the queue.  Remove the PCI flag from zfcp, it is not
necessary.
Acked-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The current number based id ERP logging is replaced by a string
based tag version. The benefit is an easier location of the code in
question and the removal of the lengthy array referencing the
individual messages.
The string (7 bytes) based version does not use more space since those
bytes were "used" anyway due to the alignment of the structure.
The encoding of the 7 byte string is as follows
        [0-1] = filename
        [2-5] = task/function
        [6]   = section
Due to the character of this string (fixed length) a string
termination is not required here.
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

An adapter close was always performed whether it was required,
(e.g. in an error scenario) or not (e.g. initial open).
This patch is changing the process in only doing an
adapter close when it is required.
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The status read response FSF_STATUS_READ_SUB_ERROR_PORT is not
defined in the specs and therefore not valid.
All occurrences are removed from the code.
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Issue ELS ADISC requests from workqueue. This allows the link test
request to be sent when the request queue is full due to I/O load for
other remote ports. It also simplifies request queue locking,
zfcp_fsf_send_fcp_command_task is now the only function that has
interrupts disabled from the caller. This is also a prereq for the FC
passthrough support that issues ELS requests from userspace.
Acked-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

When the SCSI midlayer is running error recovery, the low-level error
recovery in zfcp could be running and preventing the SCSI midlayer to
issue error recovery requests. To avoid unnecessary error recovery
escalation, wait for the zfcp erp to finish and retry if necessary.

While reworking the SCSI eh handlers, alsa cleanup the code and
simplify the interface from zfcp_scsi to the fsf layer.
Acked-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

For calls from zfcp erp, scsi_eh and sysfs switch the calls issuing
FSF requests to zfcp_fsf_req_sbal_get to wait for free SBALs.
Acked-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Only increment the req_id for successfully issued requests. This
avoids some confusion when debugging issued fsf requests.
Acked-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The lock only needs to protect the softirq context called from qdio
against the userspace context called from sysfs. spin_lock and
spin_lock_bh is enough.
Acked-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Provide measurement data for the utilisation of the QDIO outbound queue.
The additional value allows to calculate an average queue utilisation
by looking at the deltas per time unit. Needed for capacity planning.
It is up to user space to handle wrap-arounds of the 64 bit value.

The new counter neatly complements the existing counter for queue full
conditions. That is why, both statistics counter have been integrated.
Signed-off-by: NMartin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Use the device pointer in zfcp_unit for tracking if we have a
registered SCSI device. With this approach, the flag
ZFCP_STATUS_UNIT_REGISTERED is only redundant and can be removed.
Acked-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

PORT_PHYS_CLOSING is only set and cleared, but not actually used
for status checking.

PORT_INVALID_WWPN is set when the GID_PN request does not return
a d_id for a remote port, e.g. when a remote port has been
unplugged. For this case, the d_id is zero. In the erp we can
check the d_id and use the normal escalation procedure that gives
up after three retries and remove the special case.

PORT_NO_WWPN is unused: Each port in the remote port list has a
valid wwpn. The WKA ports are now tracked outside the port
list. Remove the PORT_NO_WWPN flag, since this is no longer set
for any port.
Acked-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The SCSI core calls scsi_proc_hostdir_add() from within
scsi_host_alloc(), but the corresponding scsi_proc_hostdir_rm()
routine is called from within scsi_remove_host().  As a result, if a
host is allocated and then deallocated without ever being registered,
the host's directory in /proc is leaked.

This patch (as1181b) fixes this bug in the SCSI core by moving
scsi_proc_hostdir_rm() into scsi_host_dev_release().
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

sym53c8xx prints a negotiation message after every check condition.
This can add up to a lot of messages for removable-medium devices
(CD-ROM, tape drives, etc.) that are being polled, since they return
check condition when no medium is present.  This patch suppresses the
negotiation message if it would be the same as the last one printed.
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

sym53c8xx uses a command queue depth of 2 for untagged devices,
without good reason.  This _mostly_ seems to work ok, but it has
caused me some subtle problems.  For example, I have an application
where one thread sends write commands to a tape drive, and another
thread sends log sense polling commands.  With a queue depth of
2, the polling commands end up being starved for long periods of
time while multiple write commands are serviced (this may also be
related to the fact the the sg driver queues commands in LIFO order).
This problem is fixed by changing the queue depth to 1 for untagged
devices.  I have tested this change extensively with many different
tape drives, medium changers, and disk drives (disk drives of course
use tagged commands and are therefore unaffected by this patch).
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

sym_init_device() doesn't check if pci_iomap() fails.  It also tries
to map device RAM without first checking FE_RAM.

1) Move some initialization from sym_init_device() to the top of
   sym2_probe().
2) Rename sym_init_device() to sym_iomap_device().
3) Call sym_iomap_device() after sym_check_supported() instead of
   before so that device->chip.features will be set.
4) Check FE_RAM in sym_iomap_device() before mapping RAM.
5) If sym_iomap_device() cannot map registers, then abort.
6) If sym_iomap_device() cannot map RAM, then fall back to not using
   RAM and continue.
7) Remove the check for FE_RAM in sym_attach() since dev->ram_base
   is now always set correctly.
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

During sym2_probe(), sym_init_device() does pci_iomap(), but there is
no corresponding pci_iounmap() if an error occurs before sym_attach()
copies sym_device::s.{ioaddr,ramaddr} to np.
1) Add the sym_iounmap_device() function.
2) Call sym_iounmap_device() if an error occurs between
   sym_init_device() and the time sym_attach() allocates np.
3) Make sym_attach() copy sym_device::s.{ioaddr,ramaddr} to np before
   calling any function that can fail so that sym_free_resources()
   will do the unmap instead of sym_iounmap_device().

Also fixed by this patch:
During sym2_probe(), if sym_check_raid() returns nonzero, then
pci_release_regions() is never called.
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

If sym_attach() gets an error at or before request_irq(), then
sym_free_resources() will call free_irq() for an unregistered
interrupt handler.
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

If sym_attach() fails to allocate np, the error path will dereference
a NULL pointer for printk.
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch fixes two bugs:

1) rmmod sym53c8xx uses shost after freeing it with
   scsi_put_host(shost).

2) insmod sym53c8xx doesn't call scsi_put_host(shost) if
   scsi_add_host() fails, causing a memory leak on the error path.
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Expose the debug and fastfail parameters to /sys/module/ipr/parameters such
that they can be enabled/disabled at run time.
Signed-off-by: NWayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch (as1188) combines the tests for decrementing a drive's
reported capacity and expands the comment.  It also adds an
informational message to the system log, informing the user when the
reported value has been changed.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>