Change details:
This patch contains additional structure and function definition changes
that are required to enable the new msgq/enet/txrx redesign introduced
by the previous 4 patches.
 - structure and function definition changes to header files as a result
   of Ethport, Enet, IOCEth, Tx, Rx redesign.
 - ethtool changes to use new enet function and definitions
 - Set number of Tx and Rx queues bassed on underlying hardware. Define
   separate macros for maximum and supported numbers of Tx and Rx queues
   based on underlying hardware. Take VLAN header into account for MTU
   calculation. Default to INTx mode when pci_enable_msix() fails. Set a
   bit in Rx poll routine, check and wait for that bit to be cleared in
   the cleanup routine before proceeding.
 - The TX and Rx coalesce settings are programmed in steps of 5 us. The value
   that are not divisible by 5 are rounded to the next lower number. This was
   causing the value os 1 to 4 to be rounded to 0, which is an invalid setting.
   When creating Rx and Tx object, we are currently assigning the default
   values of Rx and Tx coalescing_timeo. If these values are changed in the
   driver to a different value, the change is lost during such operations as
   MTU change. In order to avoid that, pass the configured value of
   coalescing_timeo before Rx and Tx object creation. Fix
   bnad_tx_coalescing_timeo_set() so it applies to all the Tx objects.
 - Reorg uninitialization path in case of pci_probe failure.
 - Hardware clock setup changes to pass asic generation, port modes and
   asic mode as part firmware boot parameters to firmware.
 - FW mailbox interface changes to defined asic specific mailbox interfaces.
   h/w mailbox interfaces take 8-bit FIDs and 2-bit port id for owner. Cleaned
   up mailbox definitions and usage for new and old HW. Eliminated usage of
   ASIC ID. MSI-X vector assignment and programming done by firmware. Fixed
   host offsets for CPE/RME queue registers.
 - Implement polling mechanism for FW ready to have poll mechanism replaces
   the current interrupt based FW READY method. The timer based poll routine
   in IOC will query the ioc_fwstate register to see if there is a state
   change in FW, and sends the READY event. Removed infrastructure needed to
   support mbox READY event from fw as well as IOC code.
 - Move FW init to HW init. Handle the case where PCI mapping goes away when
   IOCPF state machine is waiting for semaphore.
 - Add IOC mbox call back to client indicating that the command is sent.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the Brocade driver into drivers/net/ethernet/brocade/ and make
the necessary Kconfig and Makefile changes.

CC: Rasesh Mody <rmody@brocade.com>
CC: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change details:
 - Introducing new file bfi_reg.h for consolidating all supported hardware
   registers. This file completely replaces bfi_ctreg.h.
 - Updated ioc code as per register definition change.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Split the hw interface into common and asic specific to support new asic
   in the future.
 - Fix bfa_ioc_ct_isr_mode_set() to also include the case that we are already
   in the desired msix mode.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - ioc->cna is always set to 1 for eth functions, remove the check that
   asserts IOC is in CNA mode in bfa_ioc_firmware_lock() and
   bfa_ioc_firmware_unlock() in bfa_ioc_ct.c.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During a kernel crash, bna control path state machine and firmware do not
get a notification and hence are not cleanly shutdown. The registers
holding driver/IOC state information are not reset back to valid
disabled/parking values. This causes subsequent driver initialization
to hang during kdump kernel boot. This patch, during the initialization
of first PCI function, resets corresponding register when unclean shutown
is detect by reading chip registers. This will make sure that ioc/fw
gets clean re-initialization.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
	- Made IOC auto_recovery synchronized and not timer based.
	- Only one PCI function will attempt to recover and reinitialize
	the ASIC on a failure, that too after all the active PCI
	functions acknowledge the IOC failure.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As suggested by Stephen Hemminger:
1) Made functions and data structures static wherever possible.
2) Removed unused code.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the patch to fix the build break caused by multiple
definitions of symbols between Brocade's FC/FCOE driver(BFA)
and 10G Networking Driver(BNA).

Changes are:

1. locally used functions are made static 

2. unused functions are removed

3. using unique namespaces for the function names that must be
globally visible
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is patch 1/6 which contains linux driver source for
Brocade's BR1010/BR1020 10Gb CEE capable ethernet adapter.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clear PSS memory reset that is set as part of power-on-reset (pci reset).
Complete PMM memory reset before BISTR start. Clear EDRAM BISTR start bit
after fixed delay. BISTR DONE bit status is not getting set. Use a fixed
1ms delay for BISTR now. Expose PMM IT memory definitions to host.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch enables support of new mezzanine cards for HP and IBM blade server.

- Add new pciids for HP and IBM mezzanine card.
- Add a new firmware image for HP mezzanine card, which is running in
  FC only mode. Rename firmware image to reflect the difference. Change the
  firmware download code accordingly for the above changes.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Use dummy interrupt handlers till chip initialization is complete.
Install real interrupt handlers after chip initialization.

Also removed msix installation code in bfa_iocfc_init().
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

ioc_recover failed to work in fcmode.

Fixed the code to initialize the ioc_regs.err_set during the
notify_hbfail.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Clear LL_HALT and PSS_ERR bit in the interrupt status register on an IOC crash.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add support for faster IOC recovery after failure.

Split bfa_ioc.c into three files:
  bfa_ioc.c:    Common code shared between crossbow and catapult ASIC's.

  bfa_ioc_cb.c: Code specific to the crossbow, reg mapping and
                interrupt related routines.

  bfa_ioc_ct.c: Code specific to the catapult, reg mapping and
                interrupt related routines.

Fix to make sure IOC reinitialize's properly on enable request -
update the ioc_fwstate reg with BFI_IOC_FAIL on ioc disable mbox cmd
timeout.

Makefile changes to support the 2 newly added files bfa_ioc_cb.c and
bfa_ioc_ct.c.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>