task_numa_work skips small VMAs. At the time the logic was to reduce the
scanning overhead which was considerable. It is a dubious hack at best.
It would make much more sense to cache where faults have been observed
and only rescan those regions during subsequent PTE scans. Remove this
hack as motivation to do it properly in the future.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-29-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

Currently automatic NUMA balancing is unable to distinguish between false
shared versus private pages except by ignoring pages with an elevated
page_mapcount entirely. This avoids shared pages bouncing between the
nodes whose task is using them but that is ignored quite a lot of data.

This patch kicks away the training wheels in preparation for adding support
for identifying shared/private pages is now in place. The ordering is so
that the impact of the shared/private detection can be easily measured. Note
that the patch does not migrate shared, file-backed within vmas marked
VM_EXEC as these are generally shared library pages. Migrating such pages
is not beneficial as there is an expectation they are read-shared between
caches and iTLB and iCache pressure is generally low.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-28-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

task_numa_placement checks current->mm but after buffers for faults
have already been uselessly allocated. Move the check earlier.

[peterz@infradead.org: Identified the problem]
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-27-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

Ideally it would be possible to distinguish between NUMA hinting faults
that are private to a task and those that are shared.  This patch prepares
infrastructure for separately accounting shared and private faults by
allocating the necessary buffers and passing in relevant information. For
now, all faults are treated as private and detection will be introduced
later.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-26-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

A preferred node is selected based on the node the most NUMA hinting
faults was incurred on. There is no guarantee that the task is running
on that node at the time so this patch rescheules the task to run on
the most idle CPU of the selected node when selected. This avoids
waiting for the balancer to make a decision.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-25-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

Just as "sched: Favour moving tasks towards the preferred node" favours
moving tasks towards nodes with a higher number of recorded NUMA hinting
faults, this patch resists moving tasks towards nodes with lower faults.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-24-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

This patch favours moving tasks towards NUMA node that recorded a higher
number of NUMA faults during active load balancing.  Ideally this is
self-reinforcing as the longer the task runs on that node, the more faults
it should incur causing task_numa_placement to keep the task running on that
node. In reality a big weakness is that the nodes CPUs can be overloaded
and it would be more efficient to queue tasks on an idle node and migrate
to the new node. This would require additional smarts in the balancer so
for now the balancer will simply prefer to place the task on the preferred
node for a PTE scans which is controlled by the numa_balancing_settle_count
sysctl. Once the settle_count number of scans has complete the schedule
is free to place the task on an alternative node if the load is imbalanced.

[srikar@linux.vnet.ibm.com: Fixed statistics]
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
[ Tunable and use higher faults instead of preferred. ]
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-23-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

NUMA hinting fault counts and placement decisions are both recorded in the
same array which distorts the samples in an unpredictable fashion. The values
linearly accumulate during the scan and then decay creating a sawtooth-like
pattern in the per-node counts. It also means that placement decisions are
time sensitive. At best it means that it is very difficult to state that
the buffer holds a decaying average of past faulting behaviour. At worst,
it can confuse the load balancer if it sees one node with an artifically high
count due to very recent faulting activity and may create a bouncing effect.

This patch adds a second array. numa_faults stores the historical data
which is used for placement decisions. numa_faults_buffer holds the
fault activity during the current scan window. When the scan completes,
numa_faults decays and the values from numa_faults_buffer are copied
across.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-22-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

This patch selects a preferred node for a task to run on based on the
NUMA hinting faults. This information is later used to migrate tasks
towards the node during balancing.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-21-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

This patch tracks what nodes numa hinting faults were incurred on.
This information is later used to schedule a task on the node storing
the pages most frequently faulted by the task.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-20-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

NUMA PTE scanning slows if a NUMA hinting fault was trapped and no page
was migrated. For long-lived but idle processes there may be no faults
but the scan rate will be high and just waste CPU. This patch will slow
the scan rate for processes that are not trapping faults.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-19-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

The NUMA PTE scan rate is controlled with a combination of the
numa_balancing_scan_period_min, numa_balancing_scan_period_max and
numa_balancing_scan_size. This scan rate is independent of the size
of the task and as an aside it is further complicated by the fact that
numa_balancing_scan_size controls how many pages are marked pte_numa and
not how much virtual memory is scanned.

In combination, it is almost impossible to meaningfully tune the min and
max scan periods and reasoning about performance is complex when the time
to complete a full scan is is partially a function of the tasks memory
size. This patch alters the semantic of the min and max tunables to be
about tuning the length time it takes to complete a scan of a tasks occupied
virtual address space. Conceptually this is a lot easier to understand. There
is a "sanity" check to ensure the scan rate is never extremely fast based on
the amount of virtual memory that should be scanned in a second. The default
of 2.5G seems arbitrary but it is to have the maximum scan rate after the
patch roughly match the maximum scan rate before the patch was applied.

On a similar note, numa_scan_period is in milliseconds and not
jiffies. Properly placed pages slow the scanning rate but adding 10 jiffies
to numa_scan_period means that the rate scanning slows depends on HZ which
is confusing. Get rid of the jiffies_to_msec conversion and treat it as ms.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-18-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

Scan delay logic and resets are currently initialised to start scanning
immediately instead of delaying properly. Initialise them properly at
fork time and catch when a new mm has been allocated.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-17-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

PTE scanning and NUMA hinting fault handling is expensive so commit
5bca2303 ("mm: sched: numa: Delay PTE scanning until a task is scheduled
on a new node") deferred the PTE scan until a task had been scheduled on
another node. The problem is that in the purely shared memory case that
this may never happen and no NUMA hinting fault information will be
captured. We are not ruling out the possibility that something better
can be done here but for now, this patch needs to be reverted and depend
entirely on the scan_delay to avoid punishing short-lived processes.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-16-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

Avoiding marking PTEs pte_numa because a particular NUMA node is migrate rate
limited sees like a bad idea. Even if this node can't migrate anymore other
nodes might and we want up-to-date information to do balance decisions.
We already rate limit the actual migrations, this should leave enough
bandwidth to allow the non-migrating scanning. I think its important we
keep up-to-date information if we're going to do placement based on it.
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1381141781-10992-15-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

With a trace_printk("working\n"); right after the cmpxchg in
task_numa_work() we can see that of a 4 thread process, its always the
same task winning the race and doing the protection change.

This is a problem since the task doing the protection change has a
penalty for taking faults -- it is busy when marking the PTEs. If its
always the same task the ->numa_faults[] get severely skewed.

Avoid this by delaying the task doing the protection change such that
it is unlikely to win the privilege again.

Before:

root@interlagos:~# grep "thread 0/.*working" /debug/tracing/trace | tail -15
      thread 0/0-3232  [022] ....   212.787402: task_numa_work: working
      thread 0/0-3232  [022] ....   212.888473: task_numa_work: working
      thread 0/0-3232  [022] ....   212.989538: task_numa_work: working
      thread 0/0-3232  [022] ....   213.090602: task_numa_work: working
      thread 0/0-3232  [022] ....   213.191667: task_numa_work: working
      thread 0/0-3232  [022] ....   213.292734: task_numa_work: working
      thread 0/0-3232  [022] ....   213.393804: task_numa_work: working
      thread 0/0-3232  [022] ....   213.494869: task_numa_work: working
      thread 0/0-3232  [022] ....   213.596937: task_numa_work: working
      thread 0/0-3232  [022] ....   213.699000: task_numa_work: working
      thread 0/0-3232  [022] ....   213.801067: task_numa_work: working
      thread 0/0-3232  [022] ....   213.903155: task_numa_work: working
      thread 0/0-3232  [022] ....   214.005201: task_numa_work: working
      thread 0/0-3232  [022] ....   214.107266: task_numa_work: working
      thread 0/0-3232  [022] ....   214.209342: task_numa_work: working

After:

root@interlagos:~# grep "thread 0/.*working" /debug/tracing/trace | tail -15
      thread 0/0-3253  [005] ....   136.865051: task_numa_work: working
      thread 0/2-3255  [026] ....   136.965134: task_numa_work: working
      thread 0/3-3256  [024] ....   137.065217: task_numa_work: working
      thread 0/3-3256  [024] ....   137.165302: task_numa_work: working
      thread 0/3-3256  [024] ....   137.265382: task_numa_work: working
      thread 0/0-3253  [004] ....   137.366465: task_numa_work: working
      thread 0/2-3255  [026] ....   137.466549: task_numa_work: working
      thread 0/0-3253  [004] ....   137.566629: task_numa_work: working
      thread 0/0-3253  [004] ....   137.666711: task_numa_work: working
      thread 0/1-3254  [028] ....   137.766799: task_numa_work: working
      thread 0/0-3253  [004] ....   137.866876: task_numa_work: working
      thread 0/2-3255  [026] ....   137.966960: task_numa_work: working
      thread 0/1-3254  [028] ....   138.067041: task_numa_work: working
      thread 0/2-3255  [026] ....   138.167123: task_numa_work: working
      thread 0/3-3256  [024] ....   138.267207: task_numa_work: working
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1381141781-10992-14-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

The zero page is not replicated between nodes and is often shared between
processes. The data is read-only and likely to be cached in local CPUs
if heavily accessed meaning that the remote memory access cost is less
of a concern. This patch prevents trapping faults on the zero pages. For
tasks using the zero page this will reduce the number of PTE updates,
TLB flushes and hinting faults.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
[ Correct use of is_huge_zero_page]
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-13-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

NUMA PTE scanning is expensive both in terms of the scanning itself and
the TLB flush if there are any updates. The TLB flush is avoided if no
PTEs are updated but there is a bug where transhuge PMDs are considered
to be updated even if they were already pmd_numa. This patch addresses
the problem and TLB flushes should be reduced.

Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reviewed-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NMel Gorman <mgorman@suse.de>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-12-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

NUMA PTE scanning is expensive both in terms of the scanning itself and
the TLB flush if there are any updates. Currently non-present PTEs are
accounted for as an update and incurring a TLB flush where it is only
necessary for anonymous migration entries. This patch addresses the
problem and should reduce TLB flushes.

Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reviewed-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NMel Gorman <mgorman@suse.de>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-11-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

A THP PMD update is accounted for as 512 pages updated in vmstat.  This is
large difference when estimating the cost of automatic NUMA balancing and
can be misleading when comparing results that had collapsed versus split
THP. This patch addresses the accounting issue.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-10-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

THP migration uses the page lock to guard against parallel allocations
but there are cases like this still open

  Task A					Task B
  ---------------------				---------------------
  do_huge_pmd_numa_page				do_huge_pmd_numa_page
  lock_page
  mpol_misplaced == -1
  unlock_page
  goto clear_pmdnuma
						lock_page
						mpol_misplaced == 2
						migrate_misplaced_transhuge
  pmd = pmd_mknonnuma
  set_pmd_at

During hours of testing, one crashed with weird errors and while I have
no direct evidence, I suspect something like the race above happened.
This patch extends the page lock to being held until the pmd_numa is
cleared to prevent migration starting in parallel while the pmd_numa is
being cleared. It also flushes the old pmd entry and orders pagetable
insertion before rmap insertion.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-9-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

There are three callers of task_numa_fault():

 - do_huge_pmd_numa_page():
     Accounts against the current node, not the node where the
     page resides, unless we migrated, in which case it accounts
     against the node we migrated to.

 - do_numa_page():
     Accounts against the current node, not the node where the
     page resides, unless we migrated, in which case it accounts
     against the node we migrated to.

 - do_pmd_numa_page():
     Accounts not at all when the page isn't migrated, otherwise
     accounts against the node we migrated towards.

This seems wrong to me; all three sites should have the same
sementaics, furthermore we should accounts against where the page
really is, we already know where the task is.

So modify all three sites to always account; we did after all receive
the fault; and always account to where the page is after migration,
regardless of success.

They all still differ on when they clear the PTE/PMD; ideally that
would get sorted too.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-8-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

THP migrations are serialised by the page lock but on its own that does
not prevent THP splits. If the page is split during THP migration then
the pmd_same checks will prevent page table corruption but the unlock page
and other fix-ups potentially will cause corruption. This patch takes the
anon_vma lock to prevent parallel splits during migration.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-7-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

The locking for migrating THP is unusual. While normal page migration
prevents parallel accesses using a migration PTE, THP migration relies on
a combination of the page_table_lock, the page lock and the existance of
the NUMA hinting PTE to guarantee safety but there is a bug in the scheme.

If a THP page is currently being migrated and another thread traps a
fault on the same page it checks if the page is misplaced. If it is not,
then pmd_numa is cleared. The problem is that it checks if the page is
misplaced without holding the page lock meaning that the racing thread
can be migrating the THP when the second thread clears the NUMA bit
and faults a stale page.

This patch checks if the page is potentially being migrated and stalls
using the lock_page if it is potentially being migrated before checking
if the page is misplaced or not.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-6-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

If another task handled a hinting fault in parallel then do not double
account for it.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-5-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

Fix a 80 column violation and a PTE vs PMD reference.
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1381141781-10992-4-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1381141781-10992-3-git-send-email-mgorman@suse.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

Merge Linux v3.12-rc4 to fix a conflict and also to refresh the tree
before applying more scheduler patches.

Conflicts:
	arch/avr32/include/asm/Kbuild
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Modify the code to use current_euid(), and in_egroup_p, as in done
in fs/proc/proc_sysctl.c:test_perm()

Cc: stable@vger.kernel.org
Reviewed-by: NEric Sandeen <sandeen@redhat.com>
Reported-by: NEric Sandeen <sandeen@redhat.com>
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are the outstanding target fixes queued up for v3.12-rc4 code.

  The highlights include:

   - Make vhost/scsi tag percpu_ida_alloc() use GFP_ATOMIC
   - Allow sess_cmd_map allocation failure fallback to use vzalloc
   - Fix COMPARE_AND_WRITE se_cmd->data_length bug with FILEIO backends
   - Fixes for COMPARE_AND_WRITE callback recursive failure OOPs + non
     zero scsi_status bug
   - Make iscsi-target do acknowledgement tag release from RX context
   - Setup iscsi-target with extra (cmdsn_depth / 2) percpu_ida tags

  Also included is a iscsi-target patch CC'ed for v3.10+ that avoids
  legacy wait_for_task=true release during fast-past StatSN
  acknowledgement, and two other SRP target related patches that address
  long-standing issues that are CC'ed for v3.3+.

  Extra thanks to Thomas Glanzmann for his testing feedback with
  COMPARE_AND_WRITE + EXTENDED_COPY VAAI logic"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
  iscsi-target: Perform release of acknowledged tags from RX context
  iscsi-target: Only perform wait_for_tasks when performing shutdown
  target: Fail on non zero scsi_status in compare_and_write_callback
  target: Fix recursive COMPARE_AND_WRITE callback failure
  target: Reset data_length for COMPARE_AND_WRITE to NoLB * block_size
  ib_srpt: always set response for task management
  target: Fall back to vzalloc upon ->sess_cmd_map kzalloc failure
  vhost/scsi: Use GFP_ATOMIC with percpu_ida_alloc for obtaining tag
  ib_srpt: Destroy cm_id before destroying QP.
  target: Fix xop->dbl assignment in target_xcopy_parse_segdesc_02

Pull slave-dmaengine fixes from Vinod Koul:
 "Here is the slave dmanegine fixes.  We have the fix for deadlock issue
  on imx-dma by Michael and Josh's edma config fix along with author
  change"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: imx-dma: fix callback path in tasklet
  dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
  dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
  dma/Kconfig: Make TI_EDMA select TI_PRIV_EDMA
  edma: Update author email address

In 76854c7e ("sched: Use
rt.nr_cpus_allowed to recover select_task_rq() cycles") an
optimization was added to select_task_rq_rt() that immediately
returns when p->nr_cpus_allowed == 1 at the beginning of the
function.

This makes the latter p->nr_cpus_allowed > 1 check redundant,
which can now be removed.
Signed-off-by: NShawn Bohrer <sbohrer@rgmadvisors.com>
Reviewed-by: NSteven Rostedt <rostedt@goodmis.org>
Cc: Mike Galbraith <mgalbraith@suse.de>
Cc: tomk@rgmadvisors.com
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1380914693-24634-1-git-send-email-shawn.bohrer@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Pull btrfs fixes from Chris Mason:
 "This is a small collection of fixes, including a regression fix from
  Liu Bo that solves rare crashes with compression on.

  I've merged my for-linus up to 3.12-rc3 because the top commit is only
  meant for 3.12.  The rest of the fixes are also available in my master
  branch on top of my last 3.11 based pull"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: Fix crash due to not allocating integrity data for a bioset
  Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
  Btrfs: eliminate races in worker stopping code
  Btrfs: fix crash of compressed writes
  Btrfs: fix transid verify errors when recovering log tree

Pull GPIO fixes from Linus Walleij:
 "Two patches for the OMAP driver, dealing with setting up IRQs properly
  on the device tree boot path"

* tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio/omap: auto-setup a GPIO when used as an IRQ
  gpio/omap: maintain GPIO and IRQ usage separately

Pull USB fixes from Greg KH:
 "Here are none fixes for various USB driver problems.  The majority are
  gadget/musb fixes, but there are some new device ids in here as well"

* tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: add Intel Clovertrail pci id
  usb: gadget: s3c-hsotg: fix can_write limit for non-periodic endpoints
  usb: gadget: f_fs: fix error handling
  usb: musb: dsps: do not bind to "musb-hdrc"
  USB: serial: option: Ignore card reader interface on Huawei E1750
  usb: musb: gadget: fix otg active status flag
  usb: phy: gpio-vbus: fix deferred probe from __init
  usb: gadget: pxa25x_udc: fix deferred probe from __init
  usb: musb: fix otg default state

Pull tty fixes from Greg KH:
 "Here are two tty driver fixes for 3.12-rc4.

  One fixes the reported regression in the n_tty code that a number of
  people found recently, and the other one fixes an issue with xen
  consoles that broke in 3.10"

* tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  xen/hvc: allow xenboot console to be used again
  tty: Fix pty master read() after slave closes

Pull staging fixes from Greg KH:
 "Here are 4 tiny staging and iio driver fixes for 3.12-rc4.  Nothing
  major, just some small fixes for reported issues"

* tag 'staging-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: comedi: ni_65xx: (bug fix) confine insn_bits to one subdevice
  iio:magnetometer: Bugfix magnetometer default output registers
  iio: Remove debugfs entries in iio_device_unregister()
  iio: amplifiers: ad8366: Remove regulator_put

When btrfs creates a bioset, we must also allocate the integrity data pool.
Otherwise btrfs will crash when it tries to submit a bio to a checksumming
disk:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
 IP: [<ffffffff8111e28a>] mempool_alloc+0x4a/0x150
 PGD 2305e4067 PUD 23063d067 PMD 0
 Oops: 0000 [#1] PREEMPT SMP
 Modules linked in: btrfs scsi_debug xfs ext4 jbd2 ext3 jbd mbcache
sch_fq_codel eeprom lpc_ich mfd_core nfsd exportfs auth_rpcgss af_packet
raid6_pq xor zlib_deflate libcrc32c [last unloaded: scsi_debug]
 CPU: 1 PID: 4486 Comm: mount Not tainted 3.12.0-rc1-mcsum #2
 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
 task: ffff8802451c9720 ti: ffff880230698000 task.ti: ffff880230698000
 RIP: 0010:[<ffffffff8111e28a>]  [<ffffffff8111e28a>] mempool_alloc+0x4a/0x150
 RSP: 0018:ffff880230699688  EFLAGS: 00010286
 RAX: 0000000000000001 RBX: 0000000000000000 RCX: 00000000005f8445
 RDX: 0000000000000001 RSI: 0000000000000010 RDI: 0000000000000000
 RBP: ffff8802306996f8 R08: 0000000000011200 R09: 0000000000000008
 R10: 0000000000000020 R11: ffff88009d6e8000 R12: 0000000000011210
 R13: 0000000000000030 R14: ffff8802306996b8 R15: ffff8802451c9720
 FS:  00007f25b8a16800(0000) GS:ffff88024fc80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
 CR2: 0000000000000018 CR3: 0000000230576000 CR4: 00000000000007e0
 Stack:
  ffff8802451c9720 0000000000000002 ffffffff81a97100 0000000000281250
  ffffffff81a96480 ffff88024fc99150 ffff880228d18200 0000000000000000
  0000000000000000 0000000000000040 ffff880230e8c2e8 ffff8802459dc900
 Call Trace:
  [<ffffffff811b2208>] bio_integrity_alloc+0x48/0x1b0
  [<ffffffff811b26fc>] bio_integrity_prep+0xac/0x360
  [<ffffffff8111e298>] ? mempool_alloc+0x58/0x150
  [<ffffffffa03e8041>] ? alloc_extent_state+0x31/0x110 [btrfs]
  [<ffffffff81241579>] blk_queue_bio+0x1c9/0x460
  [<ffffffff8123e58a>] generic_make_request+0xca/0x100
  [<ffffffff8123e639>] submit_bio+0x79/0x160
  [<ffffffffa03f865e>] btrfs_map_bio+0x48e/0x5b0 [btrfs]
  [<ffffffffa03c821a>] btree_submit_bio_hook+0xda/0x110 [btrfs]
  [<ffffffffa03e7eba>] submit_one_bio+0x6a/0xa0 [btrfs]
  [<ffffffffa03ef450>] read_extent_buffer_pages+0x250/0x310 [btrfs]
  [<ffffffff8125eef6>] ? __radix_tree_preload+0x66/0xf0
  [<ffffffff8125f1c5>] ? radix_tree_insert+0x95/0x260
  [<ffffffffa03c66f6>] btree_read_extent_buffer_pages.constprop.128+0xb6/0x120
[btrfs]
  [<ffffffffa03c8c1a>] read_tree_block+0x3a/0x60 [btrfs]
  [<ffffffffa03caefd>] open_ctree+0x139d/0x2030 [btrfs]
  [<ffffffffa03a282a>] btrfs_mount+0x53a/0x7d0 [btrfs]
  [<ffffffff8113ab0b>] ? pcpu_alloc+0x8eb/0x9f0
  [<ffffffff81167305>] ? __kmalloc_track_caller+0x35/0x1e0
  [<ffffffff81176ba0>] mount_fs+0x20/0xd0
  [<ffffffff81191096>] vfs_kern_mount+0x76/0x120
  [<ffffffff81193320>] do_mount+0x200/0xa40
  [<ffffffff81135cdb>] ? strndup_user+0x5b/0x80
  [<ffffffff81193bf0>] SyS_mount+0x90/0xe0
  [<ffffffff8156d31d>] system_call_fastpath+0x1a/0x1f
 Code: 4c 8d 75 a8 4c 89 6d e8 45 89 e0 4c 8d 6f 30 48 89 5d d8 41 83 e0 af 48
89 fb 49 83 c6 18 4c 89 7d f8 65 4c 8b 3c 25 c0 b8 00 00 <48> 8b 73 18 44 89 c7
44 89 45 98 ff 53 20 48 85 c0 48 89 c2 74
 RIP  [<ffffffff8111e28a>] mempool_alloc+0x4a/0x150
  RSP <ffff880230699688>
 CR2: 0000000000000018
 ---[ end trace 7a96042017ed21e2 ]---
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>