Commit 70342287 [MIPS: Whitespace
cleanup.] did a lot of good and a little damage.  Revert the damage.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5875/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This change complements commits d0da7c002f7b2a93582187a9e3f73891a01d8ee4
[MIPS: DEC: Convert to new irq_chip functions] and
5359b938 [MIPS: DECstation I/O ASIC DMA
interrupt handling fix] and implements automatic handling of the two
classes of DMA interrupts the I/O ASIC implements, informational and
errors.

Informational DMA interrupts do not stop the transfer and use the
`handle_edge_irq' handler that clears the request right away so that
another request may be recorded while the previous is being handled.

DMA error interrupts stop the transfer and require a corrective action
before DMA can be reenabled.  Therefore they use the `handle_fasteoi_irq'
handler that only clears the request on the way out.  Because MIPS
processor interrupt inputs, one of which the I/O ASIC's interrupt
controller is cascaded to, are level-triggered it is recommended that
error DMA interrupt action handlers are registered with the IRQF_ONESHOT
flag set so that they are run with the interrupt line masked.

This change removes the export of clear_ioasic_dma_irq that now does not
have to be called by device drivers to clear interrupts explicitly
anymore.  Originally these interrupts were cleared in the .end handler of
the `irq_chip' structure, before it was removed.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5874/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The semantics stay the same - on Cavium Octeon the functions were dead
code (it overrides the MIPS DMA ops) - on other platforms they contained
no code at all.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5720/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/948/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/947/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add support for the LZ4 compression scheme in the ZBOOT decompression
stub, in order to support it we need to:

- select the "lz4" compression tool to compress the vmlinux.bin
  payload
- memcpy() is also required for decompress_unlz4.c so we share the
  implementation between GZIP, XZ and now LZ4
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5829/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

There is currently no corresponding ELF program header for the "text"
loadable segment which is confusing for some bootloader out there such
as CFE because it expects to find a program header matching the segment
it is trying to load. The Linux kernel ELF binary "vmlinux" has a
similar program header for the text segment so we just mimic this here
too.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5827/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add support for the XZ compression scheme in the ZBOOT decompression
stub, in order to support it we need to:

- select the "xzkern" compression tool to compress the vmlinux.bin
  payload
- link with ashldi3.o for xz_dec_run() to work
- memcpy() is also required for decompress_unxz.c so we share the
  implementation between GZIP and XZ
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5818/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When CONFIG_SYS_SUPPORTS_ZBOOT is not enabled, we will still try to
build the decompressor code in arch/mips/boot/compressed as a
dependency for producing the vmlinuz target and this will result in
the following build failure:

  OBJCOPY arch/mips/boot/compressed/vmlinux.bin
arch/mips/boot/compressed/decompress.c: In function 'decompress_kernel':
arch/mips/boot/compressed/decompress.c:105:2: error: implicit
declaration of function 'decompress'
make[1]: *** [arch/mips/boot/compressed/decompress.o] Error 1
make[1]: *** Waiting for unfinished jobs....
make: *** [vmlinuz] Error 2

This is a genuine build failure because we have no implementation for
the decompress() function body since no kernel compression method
defined in CONFIG_KERNEL_(GZIP,BZIP2...) has been enabled.

arch/mips/Makefile already guards the install target for the "vmlinuz"
binary with a proper ifdef CONFIG_SYS_SUPPORTS_ZBOOT, we now also do the
same if we attempt to do a "make vmlinuz" and show that
CONFIG_SYS_SUPPORTS_ZBOOT is not enabled.

[ralf@linux-mips.org: Cleanup the makefile rule as suggested by James
Hogan.]
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: richard@nod.at
Patchwork: https://patchwork.linux-mips.org/patch/5817/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Currently when using an initrd on a MIPS system the start of the bootmem
region of memory is set to the larger of the end of the kernel bss region
(_end) or the end of the initrd. In a typical memory layout where the
initrd is at some address above the kernel image this means that the start
of the bootmem region will be the end of the initrd. But when we are done
processing/loading the initrd we have no way to reclaim the memory region
it occupied, and we lose a large chunk of now otherwise empty RAM from our
final running system.

The bootmem code is designed to allow this initrd to be reserved (and the
code in finalize_initrd() currently does this). When the initrd is finally
processed/loaded its reserved memory is freed.

Fix the setting of the start of the bootmem map to be the end of the kernel.

[ralf@linux-mips.org: fold in the fix of Ashok Kumar <ashoks@broadcom.com>.]
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1574/
Cc: Ashok Kumar <ashoks@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/5883/
Patchwork: https://patchwork.linux-mips.org/patch/6028/
Patchwork: https://patchwork.linux-mips.org/patch/6064/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Based on quiet_cmd_X and cmd_X, this patch quiets the building output of
vmlinux.32 and vmlinux.64.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Sam Ravnborg <sam@ravnborg.org>
Patchwork: https://patchwork.linux-mips.org/patch/1766/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Panic() is going to add a \n itself and it's annoying if a panic message rolls
of the screen on a device with no scrollback.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Original patch by Jianguo Wu <wujianguo@huawei.com>.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch converts the pci_load_of_ranges function to use the new common
of_pci_range_parser.
Signed-off-by: NAndrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: NAndrew Murray <Andrew.Murray@arm.com>
Signed-off-by: NLiviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Reviewed-by: NRob Herring <rob.herring@calxeda.com>
Reviewed-by: NGrant Likely <grant.likely@secretlab.ca>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: jason@lakedaemon.net
Patchwork: https://patchwork.linux-mips.org/patch/5625/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The Asus WL520GC and WL520GU are based on the BCM5354 and clocked at
200MHz, but they do not have a clkfreq nvram variable set to the
correct value. This adds a workaround for these devices.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5843/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Some BCM5354 SoCs are running at 200MHz, but it is not possible to read
the clock from a register like it is done on some other SoC in ssb and
bcma. These devices should have a clkfreq nvram configuration value set
to 200, read it and set the clock to the correct value.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5842/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The nvram contains some gpio configuration for boards. It is stored in
a gpio<number>=name format e.g.
gpio8=wps_button
gpio4=robo_reset

This patches adds a function to parse these entries, so other driver
can use it.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5841/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Do not print the constant system type "Broadcom BCM47XX" but print the
name of the actual SoC in use and the detected board.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5839/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Detect on which board this code is running based on some nvram
settings. This is needed to start board specific workarounds and
configure the leds and buttons which are on different gpios on every board.

This patches add some boards we have seen, but there are many more.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5840
Patchwork: https://patchwork.linux-mips.org/patch/5855/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The CMP code is only designed to work with SMP configurations.
Fixes multiple build problems on certain randconfigs:

In file included from arch/mips/kernel/smp-cmp.c:34:0:
arch/mips/include/asm/smp.h:28:0:
error: "raw_smp_processor_id" redefined [-Werror]

In file included from include/linux/sched.h:30:0,
from arch/mips/kernel/smp-cmp.c:22:
include/linux/smp.h:135:0: note: this is the location of the
previous definition

In file included from arch/mips/kernel/smp-cmp.c:34:0:
arch/mips/include/asm/smp.h:57:20:
error: redefinition of 'smp_send_reschedule'

In file included from include/linux/sched.h:30:0,
from arch/mips/kernel/smp-cmp.c:22:
include/linux/smp.h:179:20: note: previous
definition of 'smp_send_reschedule' was here

In file included from arch/mips/kernel/smp-cmp.c:34:0:
arch/mips/include/asm/smp.h: In function 'smp_send_reschedule':
arch/mips/include/asm/smp.h:61:8:
error: dereferencing pointer to incomplete type
[...]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/5812/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The definition of the CP0 register used to save the smp processor
id is repicated in many files, move them all to thread_info.h.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5708/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In commit 15ef17f6
(tty: ar933x_uart: use the clk API to get the uart
clock), the AR933x UART driver for has been converted
to get the uart clock rate via the clock API and it
does not use the platform data anymore.

Remove the ar933x_uart_platform.h header file and get
rid of the superfluous variable and initialization code
in platform setup.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5832/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove unneeded error handling on the result of a call to
platform_get_resource_byname when the value is passed to devm_ioremap_resource.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression pdev,res,e,e1;
expression ret != 0;
identifier l;
@@

  res = platform_get_resource_byname(...);
- if (res == NULL) { ... \(goto l;\|return ret;\) }
  e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NGabor Juhos <juhosg@openwrt.org>
Cc: kernel-janitors@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5725/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Since commit 9a46ad6d "smp: make smp_call_function_many() use
logic similar to smp_call_function_single()",
generic_smp_call_function_single_interrupt() is an alias of
generic_smp_call_function_interrupt(), so kill the redundant call.
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Shaohua Li <shli@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Wang YanQing <udknight@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5820/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Pull parisc fix from Helge Deller:
 "This is a 2-line patch to save the CPU register which holds our task
  thread info pointer before calling a firmware function and then to
  restore it again afterwards.

  This is necessary because on some 64bit machines the high-order 32bits
  are being clobbered by the firmware call, and thus we failed to bring
  up secondary CPUs (and instead crashed the kernel) in some situations
  eg if we had more than 4GB RAM.  This patch fixes a bug which has been
  since ever in the parisc linux kernel and which prevented some people
  to use a 64bit kernel"

* 'parisc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Do not crash 64bit SMP kernels on machines with >= 4GB RAM

Pull timer fix from Ingo Molnar:
 "This tree contains a clockevents regression fix for certain ARM
  subarchitectures"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clockevents: Sanitize ticks to nsec conversion

Pull perf fixes from Ingo Molnar:
 "The tree contains three fixes:

   - Two tooling fixes

   - Reversal of the new 'MMAP2' extended mmap record ABI, introduced in
     this merge window.  (Patches were proposed to fix it but it was all
     a bit late and we felt it's safer to just delay the ABI one more
     kernel release and do it right)"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Disable PERF_RECORD_MMAP2 support
  perf scripting perl: Fix build error on Fedora 12
  perf probe: Fix to initialize fname always before use it

Pull locking fix from Ingo Molnar:
 "This tree fixes a boot crash in CONFIG_DEBUG_MUTEXES=y kernels, on
  kernels built with GCC 3.x (there are still such distros)"

Side note: it's not just a fix for old gcc versions, it's also removing
an incredibly broken/subtle check that LLVM had issues with, and that
made no sense.

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  mutex: Avoid gcc version dependent __builtin_constant_p() usage

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are the outstanding target pending fixes for v3.12-rc7.

  This includes a number of EXTENDED_COPY related fixes as a result of
  Thomas and Doug's continuing testing and feedback.

  Also included is an important vhost/scsi fix that addresses a long
  standing issue where the 'write' parameter for get_user_pages_fast()
  was incorrectly set for virtio-scsi WRITEs -> DMA_TO_DEVICE, and not
  for virtio-scsi READs -> DMA_FROM_DEVICE.

  This resulted in random userspace segfaults and other unpleasantness
  on KVM host, and unfortunately has been an issue since the initial
  merge of vhost/scsi in v3.6.  This patch is CC'ed to stable, along
  with two other less critical items"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  vhost/scsi: Fix incorrect usage of get_user_pages_fast write parameter
  target/pscsi: fix return value check
  target: Fail XCOPY for non matching source + destination block_size
  target: Generate failure for XCOPY I/O with non-zero scsi_status
  target: Add missing XCOPY I/O operation sense_buffer
  iser-target: check device before dereferencing its variable
  target: Return an error for WRITE SAME with ANCHOR==1
  target: Fix assignment of LUN in tracepoints
  target: Reject EXTENDED_COPY when emulate_3pc is disabled
  target: Allow non zero ListID in EXTENDED_COPY parameter list
  target: Make target_do_xcopy failures return INVALID_PARAMETER_LIST

Pull slave-dmaengine fixes from Vinod Koul:
 "Here is the late fixes pull request for dmaengine while you fly back
  from KS.

  We have a new dmaengine ML hosted by vger so a patch for that along
  with addition of Dave as driver mainatainer for ioat.  Other fixes are
  memeory leak fixes on edma driver, small fixes on rcar-hpbdma driver
  by Sergei"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: edma: fix another memory leak
  dma: edma: Fix memory leak
  MAINTAINERS: add to ioatdma maintainer list
  MAINTAINERS: add the new dmaengine mailing list

Since the beginning of the parisc-linux port, sometimes 64bit SMP kernels were
not able to bring up other CPUs than the monarch CPU and instead crashed the
kernel.  The reason was unclear, esp. since it involved various machines (e.g.
J5600, J6750 and SuperDome). Testing showed, that those crashes didn't happened
when less than 4GB were installed, or if a 32bit Linux kernel was booted.

In the end, the fix for those SMP problems is trivial:
During the early phase of the initialization of the CPUs, including the monarch
CPU, the PDC_PSW firmware function to enable WIDE (=64bit) mode is called.
It's documented that this firmware function may clobber various registers, and
one one of those possibly clobbered registers is %cr30 which holds the task
thread info pointer.

Now, if %cr30 would always have been clobbered, then this bug would have been
detected much earlier. But lots of testing finally showed, that - at least for
%cr30 - on some machines only the upper 32bits of the 64bit register suddenly
turned zero after the firmware call.

So, after finding the root cause, the explanation for the various crashes
became clear:
- On 32bit SMP Linux kernels all upper 32bit were zero, so we didn't faced this
  problem.
- Monarch CPUs in 64bit mode always booted sucessfully, because the inital task
  thread info pointer was below 4GB.
- Secondary CPUs booted sucessfully on machines with less than 4GB RAM because
  the upper 32bit were zero anyay.
- Secondary CPus failed to boot if we had more than 4GB RAM and the task thread
  info pointer was located above the 4GB boundary.

Finally, the patch to fix this problem is trivial by saving the %cr30 register
before the firmware call and restoring it afterwards.
Signed-off-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NJohn David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 2.6.12+
Signed-off-by: NHelge Deller <deller@gmx.de>

Pull ACPI and power management fixes from
 "These fix two bugs in the intel_pstate driver, a hibernate bug leading
  to nasty resume failures sometimes and acpi-cpufreq initialization bug
  that causes problems to happen during module unload when intel_pstate
  is in use.

  Specifics:

   - Fix for rounding errors in intel_pstate causing CPU utilization to
     be underestimated from Brennan Shacklett.

   - intel_pstate fix to always use the correct max pstate value when
     computing the min pstate from Dirk Brandewie.

   - Hibernation fix for deadlocking resume in cases when the probing of
     the device containing the image is deferred from Russ Dill.

   - acpi-cpufreq fix to prevent the module from staying in memory when
     the driver cannot be registered and then attempting to unregister
     things that have never been registered on exit"

* tag 'pm+acpi-3.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  acpi-cpufreq: Fail initialization if driver cannot be registered
  PM / hibernate: Move software_resume to late_initcall_sync
  intel_pstate: Correct calculation of min pstate value
  intel_pstate: Improve accuracy by not truncating until final result

Pull final mtd fixes from Brian Norris:
 "A few more last-minute regression fixes, prepared jointly by me and
  David Woodhouse:

   - Revert pxa3xx to its old name to avoid breaking existing
     'mtdparts=' boot strings.

   - Return GPMI NAND to its legacy ECC layout for backwards
     compatibility.  We will revisit this in 3.13.

  A note from David on the latter fix: 'This leaves a harmless cosmetic
  warning about an unused function.  At this point in the cycle I really
  don't care.'"

* tag 'for-linus-20131025' of git://git.infradead.org/linux-mtd:
  mtd: gpmi: fix ECC regression
  mtd: nand: pxa3xx: Fix registered MTD name

This patch addresses a long-standing bug where the get_user_pages_fast()
write parameter used for setting the underlying page table entry permission
bits was incorrectly set to write=1 for data_direction=DMA_TO_DEVICE, and
passed into get_user_pages_fast() via vhost_scsi_map_iov_to_sgl().

However, this parameter is intended to signal WRITEs to pinned userspace
PTEs for the virtio-scsi DMA_FROM_DEVICE -> READ payload case, and *not*
for the virtio-scsi DMA_TO_DEVICE -> WRITE payload case.

This bug would manifest itself as random process segmentation faults on
KVM host after repeated vhost starts + stops and/or with lots of vhost
endpoints + LUNs.

Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Asias He <asias@redhat.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

In case of error, the function scsi_host_lookup() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Pull vfs fixes (try two) from Al Viro:
 "nfsd performance regression fix + seq_file lseek(2) fix"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  seq_file: always update file->f_pos in seq_lseek()
  nfsd regression since delayed fput()

The "legacy" ECC layout used until 3.12-rc1 uses all the OOB area by
computing the ECC strength and ECC step size ourselves.

Commit 2febcdf8 ("mtd: gpmi: set the BCHs geometry with the ecc info")
makes the driver use the ECC info (ECC strength and ECC step size)
provided by the MTD code, and creates a different NAND ECC layout
for the BCH, and use the new ECC layout. This causes a regression:

   We can not mount the ubifs which was created by the old NAND ECC layout.

This patch fixes this issue by reverting to the legacy ECC layout.

We will probably introduce a new device-tree property to indicate that
the new ECC layout can be used. For now though, for the imminent 3.12
release, we just unconditionally revert to the 3.11 behaviour.

This leaves a harmless cosmetic warning about an unused function. At
this point in the cycle I really don't care.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Acked-by: NHuang Shijie <b32955@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Tested-by: NMarek Vasut <marex@denx.de>

This issue was first pointed out by Jiaxing Wang several months ago, but no
further comments:
https://lkml.org/lkml/2013/6/29/41

As we know pread() does not change f_pos, so after pread(), file->f_pos
and m->read_pos become different. And seq_lseek() does not update file->f_pos
if offset equals to m->read_pos, so after pread() and seq_lseek()(lseek to
m->read_pos), then a subsequent read may read from a wrong position, the
following program produces the problem:

    char str1[32] = { 0 };
    char str2[32] = { 0 };
    int poffset = 10;
    int count = 20;

    /*open any seq file*/
    int fd = open("/proc/modules", O_RDONLY);

    pread(fd, str1, count, poffset);
    printf("pread:%s\n", str1);

    /*seek to where m->read_pos is*/
    lseek(fd, poffset+count, SEEK_SET);

    /*supposed to read from poffset+count, but this read from position 0*/
    read(fd, str2, count);
    printf("read:%s\n", str2);

out put:
pread:
 ck_netbios_ns 12665
read:
 nf_conntrack_netbios

/proc/modules:
nf_conntrack_netbios_ns 12665 0 - Live 0xffffffffa038b000
nf_conntrack_broadcast 12589 1 nf_conntrack_netbios_ns, Live 0xffffffffa0386000

So we always update file->f_pos to offset in seq_lseek() to fix this issue.
Signed-off-by: NJiaxing Wang <hello.wjx@gmail.com>
Signed-off-by: NGu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Make acpi_cpufreq_init() return error codes when the driver cannot be
registered so that the module doesn't stay useless in memory and so
that acpi_cpufreq_exit() doesn't attempt to unregister things that
have never been registered when the module is unloaded.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>