If the device isn't reset, the XHCI HCD sends
SET ADDRESS to address 0 while the device is
already in Addressed state, and the request is
dropped on the floor as it is addressed to the
default address. This sequence of events, which this
patch fixes looks like this:

usb_reset_and_verify_device()
	hub_port_init()
		hub_set_address()
			SET_ADDRESS to 0 with 1
		usb_get_device_descriptor(udev, 8)
		usb_get_device_descriptor(udev, 18)
	descriptors_changed() --> goto re_enumerate:
		hub_port_logical_disconnect()
			kick_khubd()

And then:

hub_events()
	hub_port_connect_change()
		usb_disconnect()
			usb_disable_device()
		new device struct
		sets device state to Powered
		choose_address()
		hub_port_init() <-- no reset, but SET ADDRESS to 0 with 1, timeout!

The solution is to always reset the device in
hub_port_init() to put it in a known state.

Note from Sarah Sharp:

This patch should be queued for stable trees all the way back to 2.6.34,
since that was the first kernel that supported configured device reset.
The code this patch touches has been there since 2.6.32, but the bug
would never be hit before 2.6.34 because the xHCI driver would
completely reject an attempt to reset a configured device under xHCI.
Signed-off-by: NLuben Tuikov <ltuikov@yahoo.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org

The expression

	while (running_total < sg_dma_len(sg))

does not take into account that the remaining data length can be less
than sg_dma_len(sg). In that case, running_total can end up being
greater than the total data length, so an extra TRB is counted.
Changing the expression to

	while (running_total < sg_dma_len(sg) && running_total < temp)

fixes that.

This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org

Calculations like

	running_total = TRB_MAX_BUFF_SIZE -
		(sg_dma_address(sg) & (TRB_MAX_BUFF_SIZE - 1));
	if (running_total != 0)
		num_trbs++;

are incorrect, because running_total can never be zero, so the if()
expression will never be true. I think the intention was that
running_total be in the range of 0 to TRB_MAX_BUFF_SIZE-1, not 1
to TRB_MAX_BUFF_SIZE. So adding a

	running_total &= TRB_MAX_BUFF_SIZE - 1;

fixes the problem.

This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org

This makes it easier to spot some problems, which will be fixed by the
next patch in the series. Also change dev_dbg to dev_err in
check_trb_math(), so any math errors will be visible even when running
with debug disabled.

Note: This patch changes the expressions containing
"((1 << TRB_MAX_BUFF_SHIFT) - 1)" to use the equivalent
"(TRB_MAX_BUFF_SIZE - 1)". No change in behavior is intended for
those expressions.

This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org

Change the BUGs in xhci_find_new_dequeue_state() to WARN_ONs, to avoid
bringing down the box if one of them is hit

This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org

This reverts commit 637d11bf.  Sarah
wants to tweak it some more before it's applied to the tree.

Cc: Luben Tuikov <ltuikov@yahoo.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* 'for-greg' of git://gitorious.org/usb/usb:
  usb: musb: omap2430: fix kernel panic on reboot
  usb: musb: fix build breakage

Cancel idle timer in musb_platform_exit.

The idle timer could trigger after clock had been disabled leading to
kernel panic when MUSB_DEVCTL is accessed in musb_do_idle on 2.6.37.

The fault below is no longer triggered on 2.6.38-rc4 (clock is disabled
later, and only if compiled as a module, and the offending memory access
has moved) but the timer should be cancelled nonetheless.

Rebooting... musb_hdrc musb_hdrc: remove, state 4
usb usb1: USB disconnect, address 1
musb_hdrc musb_hdrc: USB bus 1 deregistered
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
Internal error: : 1028 [#1] PREEMPT
last sysfs file: /sys/kernel/uevent_seqnum
Modules linked in:
CPU: 0    Not tainted  (2.6.37+ #6)
PC is at musb_do_idle+0x24/0x138
LR is at musb_do_idle+0x18/0x138
pc : [<c02377d8>]    lr : [<c02377cc>]    psr: 80000193
sp : cf2bdd80  ip : cf2bdd80  fp : c048a20c
r10: c048a60c  r9 : c048a40c  r8 : cf85e110
r7 : cf2bc000  r6 : 40000113  r5 : c0489800  r4 : cf85e110
r3 : 00000004  r2 : 00000006  r1 : fa0ab000  r0 : cf8a7000
Flags: Nzcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c5387d  Table: 8faac019  DAC: 00000015
Process reboot (pid: 769, stack limit = 0xcf2bc2f0)
Stack: (0xcf2bdd80 to 0xcf2be000)
dd80: 00000103 c0489800 c02377b4 c005fa34 00000555 c0071a8c c04a3858 cf2bdda8
dda0: 00000555 c048a00c cf2bdda8 cf2bdda8 1838beb0 00000103 00000004 cf2bc000
ddc0: 00000001 00000001 c04896c8 0000000a 00000000 c005ac14 00000001 c003f32c
dde0: 00000000 00000025 00000000 cf2bc000 00000002 00000001 cf2bc000 00000000
de00: 00000001 c005ad08 cf2bc000 c002e07c c03ec039 ffffffff fa200000 c0033608
de20: 00000001 00000000 cf852c14 cf81f200 c045b714 c045b708 cf2bc000 c04a37e8
de40: c0033c04 cf2bc000 00000000 00000001 cf2bde68 cf2bde68 c01c3abc c004f7d8
de60: 60000013 ffffffff c0033c04 00000000 01234567 fee1dead 00000000 c006627c
de80: 00000001 c00662c8 28121969 c00663ec cfa38c40 cf9f6a00 cf2bded0 cf9f6a0c
dea0: 00000000 cf92f000 00008914 c02cd284 c04a55c8 c028b398 c00715c0 becf24a8
dec0: 30687465 00000000 00000000 00000000 00000002 1301a8c0 00000000 00000000
dee0: 00000002 1301a8c0 00000000 00000000 c0450494 cf527920 00011f10 cf2bdf08
df00: 00011f10 cf2bdf10 00011f10 cf2bdf18 c00f0b44 c004f7e8 cf2bdf18 cf2bdf18
df20: 00011f10 cf2bdf30 00011f10 cf2bdf38 cf401300 cf486100 00000008 c00d2b28
df40: 00011f10 cf401300 00200200 c00d3388 00011f10 cfb63a88 cfb63a80 c00c2f08
df60: 00000000 00000000 cfb63a80 00000000 cf0a3480 00000006 c0033c04 cfb63a80
df80: 00000000 c00c0104 00000003 cf0a3480 cfb63a80 00000000 00000001 00000004
dfa0: 00000058 c0033a80 00000000 00000001 fee1dead 28121969 01234567 00000000
dfc0: 00000000 00000001 00000004 00000058 00000001 00000001 00000000 00000001
dfe0: 4024d200 becf2cb0 00009210 4024d218 60000010 fee1dead 00000000 00000000
[<c02377d8>] (musb_do_idle+0x24/0x138) from [<c005fa34>] (run_timer_softirq+0x1a8/0x26)
[<c005fa34>] (run_timer_softirq+0x1a8/0x26c) from [<c005ac14>] (__do_softirq+0x88/0x13)
[<c005ac14>] (__do_softirq+0x88/0x138) from [<c005ad08>] (irq_exit+0x44/0x98)
[<c005ad08>] (irq_exit+0x44/0x98) from [<c002e07c>] (asm_do_IRQ+0x7c/0xa0)
[<c002e07c>] (asm_do_IRQ+0x7c/0xa0) from [<c0033608>] (__irq_svc+0x48/0xa8)
Exception stack(0xcf2bde20 to 0xcf2bde68)
de20: 00000001 00000000 cf852c14 cf81f200 c045b714 c045b708 cf2bc000 c04a37e8
de40: c0033c04 cf2bc000 00000000 00000001 cf2bde68 cf2bde68 c01c3abc c004f7d8
de60: 60000013 ffffffff
[<c0033608>] (__irq_svc+0x48/0xa8) from [<c004f7d8>] (sub_preempt_count+0x0/0xb8)
Code: ebf86030 e5940098 e594108c e5902010 (e5d13060)
---[ end trace 3689c0d808f9bf7c ]---
Kernel panic - not syncing: Fatal exception in interrupt

Cc: stable <stable@kernel.org>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I picked up a new Sierra usb 308 (At&t Shockwave) on 2/2011 and the vendor code
is 0x0f3d

Looking up vendor and product id's I see:

0f3d  Airprime, Incorporated
 0112  CDMA 1xEVDO PC Card, PC 5220

Sierra and Airprime are somehow related and I'm guessing the At&t usb 308 might
be have some common hardware with the AirPrime SL809x.
Signed-off-by: NJon Thomas <jthomas@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

tty_port_tty_get may return without any problems NULL. Handle this
case and do not oops in usb_wwan_indat_callback by dereferencing it.

The oops:
Unable to handle kernel paging request for data at address 0x000000d8
Faulting instruction address: 0xc0175b3c
Oops: Kernel access of bad area, sig: 11 [#1]
PowerPC 40x Platform
last sysfs file:
/sys/devices/pci0000:00/0000:00:00.0/0000:01:00.0/0000:02:09.2/usb1/idVendor
Modules linked in:
NIP: c0175b3c LR: c0175e7c CTR: c0215c90
REGS: c77f7d50 TRAP: 0300   Not tainted  (2.6.37-rc5)
MSR: 00021030 <ME,CE,IR,DR>  CR: 88482028  XER: 2000005f
DEAR: 000000d8, ESR: 00000000
TASK = c7141b90[1149] 'wvdial' THREAD: c2750000
GPR00: 00021030 c77f7e00 c7141b90 00000000 0000000e 00000000 0000000e c0410680
GPR08: c683db00 00000000 00000001 c03c81f8 88482028 10073ef4 ffffffb9 ffffff94
GPR16: 00000000 fde036c0 00200200 00100100 00000001 ffffff8d c34fabcc 00000000
GPR24: c71120d4 00000000 00000000 0000000e 00021030 00000000 00000000 0000000e
NIP [c0175b3c] tty_buffer_request_room+0x2c/0x194
LR [c0175e7c] tty_insert_flip_string_fixed_flag+0x3c/0xb0
Call Trace:
[c77f7e00] [00000003] 0x3 (unreliable)
[c77f7e30] [c0175e7c] tty_insert_flip_string_fixed_flag+0x3c/0xb0
[c77f7e60] [c0215df4] usb_wwan_indat_callback+0x164/0x170
...

References: https://bugzilla.kernel.org/show_bug.cgi?id=24582
Cc: Amit Shah <amitshah@gmx.net>
Cc: baoyb <baoyb@avit.org.cn>
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the device isn't reset, the XHCI HCD sends
SET ADDRESS to address 0 while the device is
already in Addressed state, and the request is
dropped on the floor as it is addressed to the
default address. This sequence of events, which this
patch fixes looks like this:

usb_reset_and_verify_device()
	hub_port_init()
		hub_set_address()
			SET_ADDRESS to 0 with 1
		usb_get_device_descriptor(udev, 8)
		usb_get_device_descriptor(udev, 18)
	descriptors_changed() --> goto re_enumerate:
		hub_port_logical_disconnect()
			kick_khubd()

And then:

hub_events()
	hub_port_connect_change()
		usb_disconnect()
			usb_disable_device()
		new device struct
		sets device state to Powered
		choose_address()
		hub_port_init() <-- no reset, but SET ADDRESS to 0 with 1, timeout!

The solution is to always reset the device in
hub_port_init() to put it in a known state.
Signed-off-by: NLuben Tuikov <ltuikov@yahoo.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

My Galaxy Spica needs this quirk when in modem mode, otherwise
it causes endless USB bus resets and is unusable in this mode.

Unfortunately Samsung decided to reuse ID of its old CDMA phone SGH-I500
for the modem part.
That's why in addition to this patch the visor driver must be prevented
from binding to SPH-I500 ID, so ACM driver can do that.
Signed-off-by: NMaciej Szmigiero <mhej@o2.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

[USB]Add Samsung SGH-I500/Android modem ID switch to visor driver

Samsung decided to reuse USB ID of its old CDMA phone SGH-I500 for the
modem part of some of their Android phones. At least Galaxy Spica
is affected.

This modem needs ACM driver and does not work with visor driver which
binds the conflicting ID for SGH-I500.
Because SGH-I500 is pretty an old hardware its best to add switch to
visor
driver in cause somebody still wants to use that phone with Linux.

Note that this is needed only when using the Android phone as modem,
not in USB storage or ADB mode.
Signed-off-by: NMaciej Szmigiero <mhej@o2.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1448) adds a quirks entry for the Keytouch QWERTY Panel
firmware, used in the IEC 60945 keyboard.  This device crashes during
enumeration when the computer asks for its configuration string
descriptor.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: Nkholis <nur.kholis.majid@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Cancel idle timer in musb_platform_exit.

The idle timer could trigger after clock had been disabled leading to
kernel panic when MUSB_DEVCTL is accessed in musb_do_idle on 2.6.37.

The fault below is no longer triggered on 2.6.38-rc4 (clock is disabled
later, and only if compiled as a module, and the offending memory access
has moved) but the timer should be cancelled nonetheless.

Rebooting... musb_hdrc musb_hdrc: remove, state 4
usb usb1: USB disconnect, address 1
musb_hdrc musb_hdrc: USB bus 1 deregistered
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
Internal error: : 1028 [#1] PREEMPT
last sysfs file: /sys/kernel/uevent_seqnum
Modules linked in:
CPU: 0    Not tainted  (2.6.37+ #6)
PC is at musb_do_idle+0x24/0x138
LR is at musb_do_idle+0x18/0x138
pc : [<c02377d8>]    lr : [<c02377cc>]    psr: 80000193
sp : cf2bdd80  ip : cf2bdd80  fp : c048a20c
r10: c048a60c  r9 : c048a40c  r8 : cf85e110
r7 : cf2bc000  r6 : 40000113  r5 : c0489800  r4 : cf85e110
r3 : 00000004  r2 : 00000006  r1 : fa0ab000  r0 : cf8a7000
Flags: Nzcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c5387d  Table: 8faac019  DAC: 00000015
Process reboot (pid: 769, stack limit = 0xcf2bc2f0)
Stack: (0xcf2bdd80 to 0xcf2be000)
dd80: 00000103 c0489800 c02377b4 c005fa34 00000555 c0071a8c c04a3858 cf2bdda8
dda0: 00000555 c048a00c cf2bdda8 cf2bdda8 1838beb0 00000103 00000004 cf2bc000
ddc0: 00000001 00000001 c04896c8 0000000a 00000000 c005ac14 00000001 c003f32c
dde0: 00000000 00000025 00000000 cf2bc000 00000002 00000001 cf2bc000 00000000
de00: 00000001 c005ad08 cf2bc000 c002e07c c03ec039 ffffffff fa200000 c0033608
de20: 00000001 00000000 cf852c14 cf81f200 c045b714 c045b708 cf2bc000 c04a37e8
de40: c0033c04 cf2bc000 00000000 00000001 cf2bde68 cf2bde68 c01c3abc c004f7d8
de60: 60000013 ffffffff c0033c04 00000000 01234567 fee1dead 00000000 c006627c
de80: 00000001 c00662c8 28121969 c00663ec cfa38c40 cf9f6a00 cf2bded0 cf9f6a0c
dea0: 00000000 cf92f000 00008914 c02cd284 c04a55c8 c028b398 c00715c0 becf24a8
dec0: 30687465 00000000 00000000 00000000 00000002 1301a8c0 00000000 00000000
dee0: 00000002 1301a8c0 00000000 00000000 c0450494 cf527920 00011f10 cf2bdf08
df00: 00011f10 cf2bdf10 00011f10 cf2bdf18 c00f0b44 c004f7e8 cf2bdf18 cf2bdf18
df20: 00011f10 cf2bdf30 00011f10 cf2bdf38 cf401300 cf486100 00000008 c00d2b28
df40: 00011f10 cf401300 00200200 c00d3388 00011f10 cfb63a88 cfb63a80 c00c2f08
df60: 00000000 00000000 cfb63a80 00000000 cf0a3480 00000006 c0033c04 cfb63a80
df80: 00000000 c00c0104 00000003 cf0a3480 cfb63a80 00000000 00000001 00000004
dfa0: 00000058 c0033a80 00000000 00000001 fee1dead 28121969 01234567 00000000
dfc0: 00000000 00000001 00000004 00000058 00000001 00000001 00000000 00000001
dfe0: 4024d200 becf2cb0 00009210 4024d218 60000010 fee1dead 00000000 00000000
[<c02377d8>] (musb_do_idle+0x24/0x138) from [<c005fa34>] (run_timer_softirq+0x1a8/0x26)
[<c005fa34>] (run_timer_softirq+0x1a8/0x26c) from [<c005ac14>] (__do_softirq+0x88/0x13)
[<c005ac14>] (__do_softirq+0x88/0x138) from [<c005ad08>] (irq_exit+0x44/0x98)
[<c005ad08>] (irq_exit+0x44/0x98) from [<c002e07c>] (asm_do_IRQ+0x7c/0xa0)
[<c002e07c>] (asm_do_IRQ+0x7c/0xa0) from [<c0033608>] (__irq_svc+0x48/0xa8)
Exception stack(0xcf2bde20 to 0xcf2bde68)
de20: 00000001 00000000 cf852c14 cf81f200 c045b714 c045b708 cf2bc000 c04a37e8
de40: c0033c04 cf2bc000 00000000 00000001 cf2bde68 cf2bde68 c01c3abc c004f7d8
de60: 60000013 ffffffff
[<c0033608>] (__irq_svc+0x48/0xa8) from [<c004f7d8>] (sub_preempt_count+0x0/0xb8)
Code: ebf86030 e5940098 e594108c e5902010 (e5d13060)
---[ end trace 3689c0d808f9bf7c ]---
Kernel panic - not syncing: Fatal exception in interrupt

Cc: stable@kernel.org
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

commit 06624818
(usb: musb: disable double buffering when it's broken),
introduced a compile error when gadget API is disabled.

Fix it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68knommu: set flow handler for secondary interrupt controller of 5249
  m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
  m68knommu: fix dereference of port.tty
  m68knommu: add missing linker __modver section
  m68knommu: fix mis-named variable int set_irq_chip loop
  m68knommu: add optimize memmove() function
  m68k: remove arch specific non-optimized memcmp()
  m68knommu: fix use of un-defined _TIF_WORK_MASK
  m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
  m68knommu: fix m548x_wdt.c compilation after headers renaming
  m68knommu: Remove dependencies on nonexistent M68KNOMMU

The secondary interrupt controller of the ColdFire 5249 code is not
setting the edge triggered flow handler. Set it.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The m68knommu arch does not define or use IRQ_FLG_LOCK in its irq
subsystem. Remove obsolete use of it.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The struct_tty associated with a port is now a direct pointer
from within the local private driver info struct. So fix all uses
of it.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Add missing linker section __modver to fix:

  LD      vmlinux
/usr/local/bin/../m68k-uclinux/bin/ld.real: error: no memory region specified for loadable section `__modver'
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Compiling for 68360 targets gives:

  CC      arch/m68knommu/platform/68360/ints.o
arch/m68knommu/platform/68360/ints.c: In function ‘init_IRQ’:
arch/m68knommu/platform/68360/ints.c:135:16: error: ‘irq’ undeclared (first use in this function)
arch/m68knommu/platform/68360/ints.c:135:16: note: each undeclared identifier is reported only once for each function it appears in

Fix variable name used.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Add an m68k/coldfire optimized memmove() function for the m68knommu arch.
This is the same function as used by m68k. Simple speed tests show this
is faster once buffers are larger than 4 bytes, and significantly faster
on much larger buffers (4 times faster above about 100 bytes).

This also goes part of the way to fixing a regression caused by commit
ea61bc46 ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memmove() fucntion
defined, since there was none in the m68knommu/lib functions.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The m68k arch implements its own memcmp() function. It is not optimized
in any way (it is the most strait forward coding of memcmp you can get).
Remove it and use the kernels standard memcmp() implementation.

This also goes part of the way to fixing a regression caused by commit
ea61bc46 ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memcmp() function
defined, since there is none in the m68knommu/lib functions.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (27 commits)
  drm/radeon/kms: hopefully fix pll issues for real (v3)
  drm/radeon/kms: add bounds checking to avivo pll algo
  drm: fix wrong usages of drm_device in DRM Developer's Guide
  drm/radeon/kms: fix a few more atombios endian issues
  drm/radeon/kms: improve 6xx/7xx CS error output
  drm/radeon/kms: check AA resolve registers on r300
  drm/radeon/kms: fix tracking of BLENDCNTL, COLOR_CHANNEL_MASK, and GB_Z on r300
  drm/radeon/kms: use linear aligned for evergreen/ni bo blits
  drm/radeon/kms: use linear aligned for 6xx/7xx bo blits
  drm/radeon: fix race between GPU reset and TTM delayed delete thread.
  drm/radeon/kms: evergreen/ni big endian fixes (v2)
  drm/radeon/kms: 6xx/7xx big endian fixes
  drm/radeon/kms: atombios big endian fixes
  drm/radeon: 6xx/7xx non-kms endian fixes
  drm/radeon/kms: optimize CS state checking for r100->r500
  drm: do not leak kernel addresses via /proc/dri/*/vma
  drm/radeon/kms: add connector table for mac g5 9600
  radeon mkregtable: Add missing fclose() calls
  drm/radeon/kms: fix interlaced modes on dce4+
  drm/radeon: fix memory debugging since d961db75
  ...

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  pci: use security_capable() when checking capablities during config space read

Transparent hugepages can only be created if rmap is fully
functional. So we must prevent hugepages to be created while
is_vma_temporary_stack() is true.

This also optmizes away some harmless but unnecessary setting of
khugepaged_scan.address and it switches some BUG_ON to VM_BUG_ON.
Signed-off-by: NAndrea Arcangeli <aarcange@redhat.com>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI / Video: Probe for output switch method when searching video devices.
  ACPI / Wakeup: Enable button GPEs unconditionally during initialization
  ACPI / ACPICA: Avoid crashing if _PRW is defined for the root object
  ACPI: Fix acpi_os_read_memory() and acpi_os_write_memory() (v2)

* 'tools-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
  tools: turbostat: style updates
  tools: turbostat: fix bitwise and operand

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (21 commits)
  dmaengine: add slave-dma maintainer
  dma: ipu_idmac: do not lose valid received data in the irq handler
  dmaengine: imx-sdma: fix up param for the last BD in sdma_prep_slave_sg()
  dmaengine: imx-sdma: correct sdmac->status in sdma_handle_channel_loop()
  dmaengine: imx-sdma: return sdmac->status in sdma_tx_status()
  dmaengine: imx-sdma: set sdmac->status to DMA_ERROR in err_out of sdma_prep_slave_sg()
  dmaengine: imx-sdma: remove IMX_DMA_SG_LOOP handling in sdma_prep_slave_sg()
  dmaengine i.MX dma: initialize dma capabilities outside channel loop
  dmaengine i.MX DMA: do not initialize chan_id field
  dmaengine i.MX dma: check sg entries for valid addresses and lengths
  dmaengine i.MX dma: set maximum segment size for our device
  dmaengine i.MX SDMA: reserve channel 0 by not registering it
  dmaengine i.MX SDMA: initialize dma capabilities outside channel loop
  dmaengine i.MX SDMA: do not initialize chan_id field
  dmaengine i.MX sdma: check sg entries for valid addresses and lengths
  dmaengine i.MX sdma: set maximum segment size for our device
  DMA: PL08x: fix channel pausing to timeout rather than lockup
  DMA: PL08x: fix infinite wait when terminating transfers
  dmaengine: imx-sdma: fix inconsistent naming in sdma_assign_cookie()
  dmaengine: imx-sdma: propagate error in sdma_probe() instead of returning 0
  ...

* 'for-2.6.38' of git://linux-nfs.org/~bfields/linux:
  nfsd: break lease on unlink due to rename
  nfsd4: acquire only one lease per file
  nfsd4: modify fi_delegations under recall_lock
  nfsd4: remove unused deleg dprintk's.
  nfsd4: split lease setting into separate function
  nfsd4: fix leak on allocation error
  nfsd4: add helper function for lease setup
  nfsd4: split up nfsd_break_deleg_cb
  NFSD: memory corruption due to writing beyond the stat array
  NFSD: use nfserr for status after decode_cb_op_status
  nfsd: don't leak dentry count on mnt_want_write failure

Merge branches 'core-fixes-for-linus' and 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  Revert "lockdep, timer: Fix del_timer_sync() annotation"

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  timer debug: Hide kernel addresses via %pK in /proc/timer_list

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Fix text_poke_smp_batch() deadlock
  perf tools: Fix thread_map event synthesizing in top and record
  watchdog, nmi: Lower the severity of error messages
  ARM: oprofile: Fix backtraces in timer mode
  oprofile: Fix usage of CONFIG_HW_PERF_EVENTS for oprofile_perf_init and friends

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, dmi, debug: Log board name (when present) in dmesg/oops output
  x86, ioapic: Don't warn about non-existing IOAPICs if we have none
  x86: Fix mwait_usable section mismatch
  x86: Readd missing irq_to_desc() in fixup_irq()
  x86: Fix section mismatch in LAPIC initialization

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: matrix_keypad - increase the limit of rows and columns
  Input: wacom - fix error path in wacom_probe()
  Input: ads7846 - check proper condition when freeing gpio
  Revert "Input: do not pass injected events back to the originating handler"
  Input: sysrq - rework re-inject logic
  Input: serio - clear pending rescans after sysfs driver rebind
  Input: rotary_encoder - use proper irqflags
  Input: wacom_w8001 - report resolution to userland

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  get rid of nameidata_dentry_drop_rcu() calling nameidata_drop_rcu()
  drop out of RCU in return_reval
  split do_revalidate() into RCU and non-RCU cases
  in do_lookup() split RCU and non-RCU cases of need_revalidate
  nothing in do_follow_link() is going to see RCU

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: check return value of alloc_extent_map()
  Btrfs - Fix memory leak in btrfs_init_new_device()
  btrfs: prevent heap corruption in btrfs_ioctl_space_info()
  Btrfs: Fix balance panic
  Btrfs: don't release pages when we can't clear the uptodate bits
  Btrfs: fix page->private races

task_show_regs used to be a debugging aid in the early bringup days
of Linux on s390. /proc/<pid>/status is a world readable file, it
is not a good idea to show the registers of a process. The only
correct fix is to remove task_show_regs.
Reported-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>