Prepare to remove the large number of S3C2410_GPxn defines
by moving to S3C2410_GPx(n) in arch/arm.

The following perl was used to change the files:

    perl -pi~ -e 's/S3C2410_GP([A-Z])([0-9]+)([^_^0-9])/S3C2410_GP\1\(\2\)\3/g'
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the new style of GPIO numbering by using a single
macro for each GPIO bank. This means S3C2410_GPA0 becomes
S3C2410_GPA(0), and so on.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The <mach/regs-gpio.h> really does not need the input and output
pin configurations as these are standard and have a generic
representation (plus the s3c24xx gpio specific code is going to
be phased out soon).

The following sed was applied to remove the lines:

    sed -i~ -e '/S3C2410_GP[A-Z][0-9]*_\INP/d' \
	    -e '/S3C2410_GP[A-Z][0-9]*_\OUTP/d' \
	    -e '/S3C2410_GPA[0-9]*_OUT/d'

to remove these.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.

Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).

Note, this does make minor changes to some drivers but
should not mess up any pending merges.

CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The use of S3C2410_GP[A-Z]x_INP and S3C2410_GP[A-Z]x_OUTP are
very rare and are taking up large amounts of space in the
regs-gpio.h header.

The GPIO layer has had generic input and out defines called
S3C2410_GPIO_INPUT and S3C2410_GPIO_OUTPUT for a while which work
for all S3C24XX GPIOs.

Do the following replacements:

   S3C2410_GP[A-Z][0-9]*_\OUTP => S3C2410_GPIO_OUTPUT
   S3C2410_GP[A-Z][0-9]*_\INP  => /S3C2410_GPIO_INPUT
   S3C2410_GPA[0-9]*_OUT       => S3C2410_GPIO_OUTPUT

to remove any usages of these and prepare the header for
the removal of these.

The following command was used to acheive this:

find . -type f -writable ! -name regs-gpio.h ! -name "*~" | xargs sed -i~ -e 's/S3C2410_GP[A-Z][0-9]*_\OUTP/S3C2410_GPIO_OUTPUT/g' -e 's/S3C2410_GP[A-Z][0-9]*_\INP/S3C2410_GPIO_INPUT/g' -e 's/S3C2410_GPA[0-9]*_OUT/S3C2410_GPIO_OUTPUT/g'
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove the s3c2410_gpio_irq2pin() function as it is not being
used in any in kernel driver and the function is probably not
being used anywhere else.

This is also part of the effort to remove any of the s3c24xx gpio
specific code that cannot be recreated by using the gpiolib
framework now in the kernel.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The USB host base address is available on both the S3C24XX and S3C64XX
ranges.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add common definition for USB OHCI platform device, add a Kconfig
to selectively compile it and add update all the users.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The platform data for the i2c-s3c2410 driver used to allow a min,
max and desired frequency for the I2C bus. This patch reduces it
to simply a desired frequency ceiling and corrects all the uses
of the platform data appropriately.

This means, for example, that on a system with a 66MHz fclk, a
request for 100KHz will achieve 65KHz which is safe and
acceptable, rather than 378KHz which it would have achieved
without this change.
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
Signed-off-by: NDaniel Silverstone <dsilvers@simtec.co.uk>
[ben-linux@fluff.org: tidy subject and description]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The usb-control.h is needed by ohci-s3c2410.c for both S3C24XX and S3C64XX
architectures, so move it to <plat/usb-control.h>
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not.  There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().

This patch fixes things to pass this string to arch_reset().  This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Can't see any immediate need for these; build tested.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

These changes were included in the S3C audio header move but are not
directly related to it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add the definition for S3C_GPIO_END to allow the PM code to build.

This means moving the GPIO bank numbers to a separate file to allow
the gpio and regs-gpio to include them. Including regs-gpio.h into
gpio.h causes too many build problems and adding gpio.h would mean
editing a large number of files.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Rename s3c2410_cpu_resume to s3c_cpu_resume and s3c2410_cpu_save to
s3c_cpu_save to remove the CPU specific naming of these functions
which are now in the generic PM code.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Since we have moved a large proportion of the PM code to the common
support area, remove the cpu specific name from the initialisation
function.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

There's a bug in calculation of IRQ_EINT_BIT introduced on the test
branch for pm changes for s3c by Ben Dooks fixed in this patch.

There's also a bit of a mystery about how wake gets to wake EINT
set of interrupts, I added a couple of lines that make it work for
EINT4+ but not sure what's meant to be there for EINT0-3.

Still, this gets GTA02 resume working again.
Signed-off-by: NAndy Green <andy@openmoko.com>
[ben-linux@fluff.org: remove irq-pm.c change]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the IRQ_EINT sleep control to be available to all
s3c impelmentations. Since s3c_irqext_wake is not large,
place it in arch/arm/plat-s3c/pm.c as adding it to a new
file would be a waste of compile time.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Start moving the PM code by moving all the common support functions
to a common location in arch/arm/plat-s3c. With the move we rename
the functions from s3cxxx_ to s3c_ to fit the new location.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The <mach/audio.h> file needs to be common to both ARCH_S3C2410 and
ARCH_S3C64XX as they share common driver code, so move it to <plat/audio.h>.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Move the IIS headers to their correct place.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add gpio_to_irq() by re-directing the call to the
generic __gpio_to_irq() code in the gpiolib.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Change the spi_s3c2410 driver to use the generic gpio calls that are now
available.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As per Russell King's last review comment, find and remove
all unnecessary includes of <linux/delay.h> in the files
that do not need them.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the fourth UART definition for the S3C2443, and at the
same time fixup the problems caused by the enlarging of the
UART array in the previous commits.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add Kconfig entries to allow more GPIO space to
be specified depending on the machine(s) selected.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Make the device i2c0 common to plat-s3c and move the
definitions from arch/arm/plat-s3c24xx/devs.c
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add new GPIO configuration calls that mesh with the
new gpiolib support.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the definition for the hsmmc device to plat-s3c
to be shared between the s3c24xx and s3c64xx platforms.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support to the Samsung serial driver for the S3C6400
and S3C6410 serial ports.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the necessary defines for <mach/uncompress.h>
to function and build an working header code block.
Signed-off-by: NBen Doioks <ben-linux@fluff.org>

Split the timer pending code out to a seperate per-machine
header so that when compiling for mach-s3c2410 or mach-s3c24a0
we can use the right timer code without having to #ifdef the
timer driver.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Split the map.h definitions into common S3C24XX code by
adding arch/arm/plat-s3c24xx/include/plat/map.h and
altering the machine specific header for the S3C24A0.

As we add a new <plat/map.h> we move the original one
in arch/arm/plat-s3c include directory to be called
map-base.h to distinguish the two files.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The definition of S3C24XX_VA_GPIO used S3C2410_PA_GPIO
where it should have read S3C24XX_PA_GPIO.
Signed-off-by: NSandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add a common include file (regs-irqtype.h) for the IRQ
trigger control register values S3C2410_EXTINT*.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Update the clock settings on resume for suspend/resume
support so that if the boot loader changes anything or
the system's PLL is reset then we return with the correct
settings.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the PLL calculation code into it's own header
file for re-use with the other plat-s3c24xx based
systems such as the S3C24A0.

Note, we change the name of s3c2410_get_pll to the
more generically named s3c24xx_get_pll as well as
the related defintions.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Only certain boards need these clocks, and they are not
available on some CPUs (such as the S3C24A0) so remove
them from arch/arm/plat-s3c24xx/clock.c and into their
own file with appropriate Kconfig entries.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

We need to add plat-s3c to the build to get the headers
that will go in here once moved from include/asm-arm so
we may as well put some useful common s3c code in here
to stop the errors generated form having nothing built.

The cpu setup is now passed the cpu idcode and the table
of supported cpus to s3c_init_cpu() to abstract the
cpu identification out of the initial io setup.

As well as moving the cpu initialisation code, we move the
map of the board specific items up to the calling code as
none of the map_io() functions actually do anything other
than pass this to iotable_init().

This patch does not rename any of the init functions that
will be common to s3c24xx and any other s3c architectures
as this can be done at a later date as it will touch all
the board support files which use functions such as
s3c24xx_init_clocks() and s3c24xx_init_uarts().

Note, the header arch/arm/plat-s3c24xx/include/plat/cpu.h
still has functions that are used by both the cpu and
board initialisation functions. This means that each board
has definitions specific to the cpu support included and
the vice-versa.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>