- 28 7月, 2006 9 次提交
-
-
由 Michael Buesch 提交于
Suspend MAC (and make MAC-suspend refcounting) when doing long periodic work. On long periodic work, we disable IRQs on the device, so we don't want the MAC to stay operating and probably miss packets due do non-delivery of interrupts. Signed-off-by: NMichael Buesch <mb@bu3sch.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Williams 提交于
Add WE-19 capabilities to prism54 fullmac driver so that it supports the necessary Wireless Extensions WPA calls. Convert reporting of WPA/RSN Generic Information Elements to IWEVGENIE rather than pre-WE-19 IWEVCUSTOM as well. Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Daniel Drake 提交于
wireless.h discourages using SIOCGIWNAME to publish the driver name which the interface belongs to. Use SIOCGIWNICKN instead. Signed-off-by: NDaniel Drake <dsd@gentoo.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Pavel Machek 提交于
ipw2200 uses // comments, and uses them for removing unneeded code. Clean it up a bit. Signed-off-by: NPavel Machek <pavel@suse.cz> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Robert Schulze 提交于
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Williams 提交于
When determining whether there's a key to set or not, orinoco should be looking at the key length, not the key data. Otherwise confusion reigns when trying to set TX key only, passing in zero-length key, but non-NULL pointer. Key length takes precedence over non-NULL key data. Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Daniel Drake 提交于
Johann Uhrmann reported a bcm43xx crash and Michael Buesch tracked it down to a problem with the new shared key auth code (recursive calls into the driver) This patch (effectively Michael's patch with a couple of small modifications) solves the problem by sending the authentication challenge response frame from a workqueue entry. I also removed a lone \n from the bcm43xx messages relating to authentication mode - this small change was previously discussed but not patched in. Signed-off-by: NDaniel Drake <dsd@gentoo.org> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NMichael Buesch <mb@bu3sch.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Robert Schulze 提交于
The driver airo (for Cisco Wlan-Cards) complains about "failed to load transform for AES", when it is loaded and CRYPTO_AES is not selected in Kconfig. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Pavel Machek 提交于
zd1201 has nasty tendency to emit magicall anti-wifi cloud when it is inserted into slot, but not used. Signed-off-by: NPavel Machek <pavel@suse.cz> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 26 7月, 2006 3 次提交
-
-
由 Michael Chan 提交于
Update version to 3.63. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Handle dev_alloc_skb() failures when initializing the RX rings. Without proper handling, the driver will crash when using a partial ring. Thanks to Stephane Doyon <sdoyon@max-t.com> for reporting the bug and providing the initial patch. Howie Xu <howie@vmware.com> also reported the same issue. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add tg3_restart_hw() to handle failures when re-initializing the device. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 7月, 2006 5 次提交
-
-
由 Nicolas Dichtel 提交于
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nicolas Dichtel 提交于
It before entering in the loop for freeing the other ifb devices. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: NJamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Slaby 提交于
Use pci_register_driver instead of pci_module_init. Use PCI_DEVICE macro. Signed-off-by: NJiri Slaby <jirislaby@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Krzysztof Halasa 提交于
WAN: Cosmetic changes to N2 and C101 drivers Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Krzysztof Halasa 提交于
WAN: Fixed a problem with PPP/raw HDLC/X.25 protocols not doing netif_dormant_off() at startup. Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 7月, 2006 3 次提交
-
-
由 Jens Osterkamp 提交于
With this patch TX queue descriptors are not chained per default any more. The pointer to next descriptor is set only when next descriptor is prepaired for transfer. Also the mechanism of checking wether Spider is ready has been changed: it checks not for CARDOWNED flag in status of previous descriptor but for a TXDMAENABLED flag in Spider's register. Signed-off-by: NMaxim Shchetynin <maxim@de.ibm.com> Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: NJens Osterkamp <Jens.Osterkamp@de.ibm.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Jens Osterkamp 提交于
We want to intitialize addr instead of data register first. Signed-off-by: NJens Osterkamp <Jens.Osterkamp@de.ibm.com> Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
When sky2 driver gets lots of received packets at once, it can get stuck. The NAPI poll routine gets called back to keep going, but since no IRQ bits are set it doesn't make progress. Increase version, since this is serious enough problem that I want to be able to tell new from old problems. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
- 15 7月, 2006 4 次提交
-
-
由 Auke Kok 提交于
Bump the version to 7.1.9-k4 to indicate three extra changes. Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
-
由 Auke Kok 提交于
A panic was reported when receiving 1522 size packets if using the default MTU. we should set the initial rx buffer length to the value that e1000changemtu sets so that we can receive any packet that would not be dropped by LPE=0. Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NAuke Kok <auke.jan.h.kok@intel.com>
-
由 Auke Kok 提交于
After removing the hardware CRC stripping which causes problems with SOL and related issues, we need to compensate for this changed size. Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
-
由 Auke Kok 提交于
The original suggested fix for netpoll was found to be racy on SMP kernels. While it is highly unlikely that this race would ever be seen in the real world due to current netpoll usage models, we implemented this updated fix to address concerns. Signed-off-by: NMitch Williams <mitch.a.williams@intel.com> Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
-
- 13 7月, 2006 16 次提交
-
-
由 Stephen Hemminger 提交于
When the driver handles multiple packets per NAPI poll, it is better to reload the receive ring, then tell the hardware. Otherwise, under packet storm with flow control, the driver/hardware will degrade down to one packet getting through per pause-exchange. Likewise on transmit, don't wakeup until a little more than minimum ring space is available. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
The documentation says we need to wait after turning on the PHY. Also, don't enable WOL by default. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
The changes to handle suspend/resume didn't handle the case where a dual port card has the first port down, but the second is running. In this driver, all NAPI polling is done on the primary port. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
Since sky2_reset gets call from sky2_resume it shouldn't be tagged with devinit. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
Patch to correct broken collision threshold mask in (same problem as sky2 driver). Should be three bits wide, but the mask only allows for 1 bit to be set. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
Patch to correct broken collision threshold mask in (same problem as sky2 driver). Should be three bits wide, but the mask only allows for 1 bit to be set. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
Patch to correct broken collision threshold mask in sky2 driver. Should be three bits wide, but the mask only allows for 1 bit to be set. Thanks & Regards Neil Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NStephen Hemminger <shemminger@osdl.org> sky2.h | 2 +- 1 files changed, 1 insertion(+), 1 deletion(-) Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Brice Goglin 提交于
Andrew Morton wrote: > All these functions return error codes, and we're not checking them. We > should. So there's a patch which marks all these things as __must_check, > which causes around 1,500 new warnings. > The following patch fixes such a warning in myri10ge. Check pci_enable_device() return value in myri10ge_resume(). Signed-off-by: NBrice Goglin <brice@myri.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Deepak Saxena 提交于
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new generic IRQ layer will complain thusly: No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>) Signed-off-by: NDeepak Saxena <dsaxena@plexity.net> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Auke Kok 提交于
There were some tso bugs that only showed up with heavy load and 16kB pages that this patch fixes by making the driver's internal use count of descriptors match the count that it was estimating it needed using the DESC_NEEDED macro. This bug caused NETDEV_WATCHDOG resets aka tx timeouts. Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Dmitry Torokhov 提交于
subsystem_configurations array is only used by an __init function, therefore it should be marked __initdata, not __devinitdata. Signed-off-by: NDmitry Torokhov <dtor@mail.ru> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Andrew Morton 提交于
drivers/net/8139cp.c: In function 'cp_init_one': drivers/net/8139cp.c:1919: warning: format '%lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t' drivers/net/8139cp.c:1919: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'resource_size_t' Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Ananda Raju 提交于
Modification and bug fixes with respect to irq registration. - Enable interrupts after request_irq - Restored MSI data register value at driver unload time Signed-off-by: NAnanda Raju <ananda.raju@neterion.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Andrew Morton 提交于
Use the new names. Cc: Auke Kok <auke-jan.h.kok@intel.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Ayaz Abdulla 提交于
This patch defines the watermark registers and fixes up the use of this register. Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Ayaz Abdulla 提交于
This patch adds the definition for the deferral registers and fixes up the use of these registers. Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-