Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This node should have a unique name so it can be distinguished when
other i2c busses are added later.
Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The Koelsch board uses the ethernet PHY LED0 as a link signal connected
to the ethernet controller. Specify the corresponding LED mode for the
PHY.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add DTS gpio-keys support for SW2 on the Koelsch board.
This makes the DT code match the legacy board code. Also
update the existing gpio-keys nodes to make use of KEY_n.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add pinctrl and SPI device for MSIOF on Koelsch.
On this board, only MSIOF0 is in use. Its bus contains a single device
(a Renesas R2A11302FT PMIC), for which no bindings are defined yet.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Prepare for the advent of MSIOF SPI, which will be spi1 to spi3.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add DT support for SDHI0, SDHI1 and SDHI2 on Koelsch.

The board specific handling of CD and WP pins are
using GPIOs. SDHI0 and SDHI1 are hooked up to regular
SD connectors while SDHI2 is using micro-SD which
is lacking WP signal.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the Koelsch board dependent part of the Ether device node.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Acked-by: NMagnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: resolved conflict]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The DU device has no DT bindings yet, instantiate it as a platform
device for now.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NMagnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: broken out of larger patch that
                             included board changes]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add pinctrl and SPI devices for QSPI on Koelsch.
Add Spansion s25fl512s SPI FLASH and MTD partitions.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This enables SATA0 in Koelsch device tree.
SATA1 is not available on Koelsch since
its pinmux configuration is fixed to PCIe.
Signed-off-by: NValentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Fix dts to have memory 1GiB @ 0_4000_0000 + 1GiB @ 2_0000_0000
according to Koelsch's hardware manual.
Signed-off-by: NTakashi Yoshii <takasi-y@ops.dti.ne.jp>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The Koelsh reference device tree is going away, copy the missing GPIO
keys device node to the Koeslch device tree file.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The external crystal frequency is 20MHz on the Koelsch board. Specify it
in the device tree.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Copy the device nodes from Koelsch reference into the Koeslch device
tree file. This will allow us to use a single DTS file regarless of
kernel configuration. In case of legacy C board code the device nodes
may or may not be used, but in the multiplatform case all the DT device
nodes are used.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

In order to allow usage of the preprocessor in the SoC device tree
sources, switch from /include/ to #include.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Koelsch base board support making use of 2 GiB of memory,
the r8a7791 SoC with the SCIF0 serial port and CA15 with
CMT timer.
Signed-off-by: NHisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: NRyo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, dropped not-yet-ready SMP/PFC]
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Now that Ether support has been added to the lager board
it is possible to use nfsroot. This configuration is
in line with that of other shmobile boards.
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The shmobile DT files available in the kernel are reference
implementations intended to be used as sample code, as well as for
development. As such, it makes sense to mount the root file system in
read/write mode by default.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Lager base board support making use of 2 GiB of memory,
the r8a7790 SoC with the SCIF0 serial port and CA15 with
ARM architected timer.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>