Currently during the full reset, the nf calibration is always
restarted from the defaults. The noise floor history buffers are
never be used again after the scan and ath reset. This patch
ensures that nf histories are always be used that helps to
improve the signal quality on congested environment
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do the magnitude/phase coeff correction only if the outlier
is detected. Updating wrong magnitude/phase coeff factor
impacts not only tx gain setting but also leads to poor
performance in congested networks. In the clear environment
the impact is very minimal because the outlier happens
very rarely according to the past experiment. It occured
less than once every 1000 calibrations.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k_hw: Fix Tx IQ Calibration hang issue in
AR9003 chips" did not consider more than one potential sample
while calculating magnitude/phase average if more than one
sample has the same value which could affect post-processing
of outlier detection that causes an undesirable Tx IQ
correction value will be assigned to tx gain settings where
outlier happens.

Cc: Kai Shi <kaishi@qca.qualcomm.com>
Reported-by: NPaul Stewart <pstew@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NPaul Stewart <pstew@google.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The chainmasks were already configured at process_ini
before doing init calibration.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Times They Are a-Changin'.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On AR9003 chips, doing three IQ calibrations will possibly cause chip
in stuck state. In noisy environment, chip could receive
a packet during the middle of three calibrations and it causes
the conflict of HW access and the eventual failure. It also
causes IQ calibration outliers which results in poor Tx EVM.

The IQ Cal procedure is after resetting the chip, run IQ cal 3 times
per each cal cycle and find the two closest readings and average of two.
The advantage of running Tx IQ cal more than once is that we can compare
calibration results for the same gain setting over multiple iterations.
Most of the cases the IQ failures were observed after first pass.

For the AR9485 and later chips, Tx IQ Calibration is performed along
with AGC cal. But for pre-AR9485 chips, Tx IQ cal HW has to be separated
from the rest of calibration HW to avoid chip hang. After all
calibrations are done in HW, we can start SW post-processing.
By doing this way, we minimize the SW difference among all chips.

The order of calibration (run IQ cal before other calibration) is also
needed to avoid chip hang for chips before AR9485. This issue was
originally observed with AR9382.

During the issue kernel log was filled with following message
ath: timeout (100000 us) on reg 0xa640: 0x00000001 & 0x00000001 != 0x00000000
ath: timeout (100000 us) on reg 0xa2c4: 0x00158dd9 & 0x00000001 != 0x00000000
ath: Unable to reset channel (2412 MHz), reset status -5
ath: Unable to set channel
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use hw supported chains instead of hard coded values.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add multiple Tx IQ cal support to improve EVM accross
different power levels.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  11161	     56	   2136	  13353	   3429	drivers/net/wireless/ath/ath9k/ar9003_paprd.o.new
  11167	     56	   2136	  13359	   342f	drivers/net/wireless/ath/ath9k/ar9003_paprd.o.old
  15428	     56	   3056	  18540	   486c	drivers/net/wireless/ath/ath9k/eeprom_4k.o.old
  15451	     56	   3056	  18563	   4883	drivers/net/wireless/ath/ath9k/eeprom_4k.o.new
  14087	     56	   2560	  16703	   413f	drivers/net/wireless/ath/ath9k/eeprom_9287.o.old
  14036	     56	   2560	  16652	   410c	drivers/net/wireless/ath/ath9k/eeprom_9287.o.new
  10041	     56	   2384	  12481	   30c1	drivers/net/wireless/ath/ath9k/ani.o.new
  10088	     56	   2384	  12528	   30f0	drivers/net/wireless/ath/ath9k/ani.o.old
   9316	   1580	   2304	  13200	   3390	drivers/net/wireless/ath/ath9k/htc_drv_init.o.new
   9316	   1580	   2304	  13200	   3390	drivers/net/wireless/ath/ath9k/htc_drv_init.o.old
  16483	     56	   3432	  19971	   4e03	drivers/net/wireless/ath/ath9k/ar9003_phy.o.new
  16517	     56	   3432	  20005	   4e25	drivers/net/wireless/ath/ath9k/ar9003_phy.o.old
  18221	    104	   2960	  21285	   5325	drivers/net/wireless/ath/ath9k/rc.o.old
  18203	    104	   2960	  21267	   5313	drivers/net/wireless/ath/ath9k/rc.o.new
  19985	     56	   4288	  24329	   5f09	drivers/net/wireless/ath/ath9k/eeprom_def.o.new
  20040	     56	   4288	  24384	   5f40	drivers/net/wireless/ath/ath9k/eeprom_def.o.old
  23997	     56	   4984	  29037	   716d	drivers/net/wireless/ath/ath9k/ar5008_phy.o.old
  23846	     56	   4984	  28886	   70d6	drivers/net/wireless/ath/ath9k/ar5008_phy.o.new
  24285	     56	   3184	  27525	   6b85	drivers/net/wireless/ath/ath9k/ar9003_eeprom.o.old
  24101	     56	   3184	  27341	   6acd	drivers/net/wireless/ath/ath9k/ar9003_eeprom.o.new
   6834	     56	   1032	   7922	   1ef2	drivers/net/wireless/ath/ath9k/ar9002_phy.o.old
   6780	     56	   1032	   7868	   1ebc	drivers/net/wireless/ath/ath9k/ar9002_phy.o.new
  36211	     64	   8624	  44899	   af63	drivers/net/wireless/ath/ath9k/hw.o.new
  36401	     64	   8624	  45089	   b021	drivers/net/wireless/ath/ath9k/hw.o.old
   9281	     56	   1496	  10833	   2a51	drivers/net/wireless/ath/ath9k/ar9003_calib.o.old
   9150	     56	   1496	  10702	   29ce	drivers/net/wireless/ath/ath9k/ar9003_calib.o.new

Use ARRAY_SIZE instead of a magic number.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9382 needs to be configured for the correct chain mask before
running AGC/TxIQ caliberation. Otherwise reset would fail.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The calibration actual calibration flags are only used by the per chip family
source files, so it makes more sense to define them in those files instead
of globally. That way the code has to test for less flags.

Also instead of using a separate callback for testing whether a particular
calibration type is supported, simply adjust ah->supp_cals in the calibration
init which is called right after the hardware reset, before any of the
calibrations are run.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The percal struct and bitmask for the initial DC calibration are not
used anywhere, so they can be removed.

Signed-off-by: Felix Fietkau <nbd@openwrt.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The noise floor history buffer is currently not kept per channel, which
can lead to problems when changing channels from a clean channel to a
noisy one. Also when switching from HT20 to HT40, the noise floor
history buffer is full of measurements, but none of them contain data
for the extension channel, which it needs quite a bit of time to recover
from.

This patch puts all the per-channel calibration data into a single data
structure, and gives the the driver control over whether that is used
per-channel or even not used for some channels.

For ath9k_htc, I decided to keep this per-channel in order to avoid
creating regressions.

For ath9k, the data is kept only for the operating channel, which saves
some space. ath9k_hw takes care of wiping old data when the operating
channel or its channel flags change.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The periodic noise floor calibration is broken on this chip family, because
it keeps triggering a software-filtered noise floor calibration, but never
reads the result before uploading the history buffer value to the hardware.

Fix this with a call to ath9k_hw_getnf(), just like on AR9002.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On AR9003 the initial noise floor calibration is currently triggered
at the end of the reset without allowing the hardware to update the
baseband settings. This could potentially make scans in noisy
environments a bit more unreliable, so use the same calibration
sequence that is used on AR9002.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To enable it we now disable and re-enable the PHY chips
after TX IQ calibration.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.

It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.

It also does not remove null void functions with return.

Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
  xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'

with some cleanups by hand.

Compile tested x86 allmodconfig only.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable TX IQ calibration, it was prematurely enabled in
previous versions.

Cc: Paul Shaw <Paul.Shaw@Atheros.com>
Cc: Thomas Hammel <Thomas.Hammel@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This goes with some new shiny TX IQ calibration that AR9003
hardware family supports.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is the last call on calib.c which acceses PHY stuff,
with this change we calib.c is now generic between both
all supported hardware families.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Calibration code touches phy registers and since these
change the calibration code needs to be abstracted.

Noise floor calibration is the only thing remaining but
since the remaining calls only touch the AR_PHY_AGC_CONTROL
register we'll just define that register conditionally, that
will be done separately. The goal is to remove the dependency
of ar9002_phy.h on calib.c

This also adds stubs to be filled for AR9003 calibration code.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>