Netgear R8500 is another BCM47094 device, it just has three BCM4366
wireless chipsets. It's a very standard DT with mostly GPIO devices.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

This is a router based on the mv88f5181 chipset.

http://www.netgear.com/support/product/WNR854T.aspx
http://wiki.openwrt.org/toh/netgear/wnr854t

[gregory.clement@free-electrons.com:
- extract dt part from "arm: orion5x: Add DT-based support for Netgear
  WNR854T"
- squashed "arm: orion5x: Alias uart0 to serial0 for all orion5x" into
this commit and move serial0 alias from dtsi to dts]
Signed-off-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Latest update to the BeagleBoard-X15 platform (revision B1)[1] updates
for allowing UHS SD cards to function with the split of supply to SD
card from a dedicated LDO.

As a result of this, AM57xx BeagleBoard-X15 now uses gpio2_30 instead
of gpio6_28 for HDMI because HDMI_LS_OE should now be switched from
GPIO6_28(Y9) to GPIO2_30 (AG8) to avoid a 1.8V GPIO toggling a 3.3V
SoC input when the SD card is in UHS 1.8V mode.

NOTE: For UHS mode to function, we need full fledged IODelay support
in kernel to be functional. IODelay support is yet to be added.

Further, It does not make much sense to spin off a new board
compatible flag since there is no real functional benefit for the
same.

Note: Even though production version is supposed to be B1, there is
over ~200 boards of previous version (A2)[2] out there which continue
to get supported with the existing dts file (to maintain compatibility
with existing bootloaders for A2) and the production board is now
supported as revb1.

[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BEAGLEBOARD_X15_REV_B1.pdf
[2] http://marc.info/?l=linux-arm-kernel&m=147273929820708&w=2Tested-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The GR8-EVB is a small board with an NextThing GR8, an Hynix MLC NAND,
an AXP209 PMIC, USB host and OTG, an SPDIF output and a connectors for CSI,
I2S and LCD.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

The Cortex A9 MPCore tile can be mounted on top of the revision
D variant of the RealView EB, so create another variant of the
DTS file for this.

arm-realview-eb-a9mp = mounted on pre-revision D baseboard
arm-realview-eb-a9mp-bbrevd = mounted on the revision D baseboard
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There used to be two versions of the RealView EB 11MPCore:

- arm-realview-eb-11mp.dts: the most common variant supported by
  QEMU with the revision C core tile
- arm-realview-eb-revb.dts: for the variant with the elder revision
  B core tile.

As it turns out that there are also a few variants of the
baseboard, unrelated to the coretile, and that these can of
course be mounted on top of each other in all permutations, we
create:

- arm-realview-eb-11mp.dts: the most common variant supported by
  QEMU with the pre-revision D baseboard and the revision C core
  tile.
- arm-realview-eb-11mp-bbrevd.dts: the revision D baseboard
  with the common revision C core tile.
- arm-realview-eb-11mp-ctrevb.dts: the pre-revision D baseboard
  with the revision B core tile.
- arm-realview-eb-11mp-bbrevd-ctrevb.dts: the revision D baseboard
  with the revision B core time.

Or as a table:

           | Core tile: C               | Core tile: B
-----------+----------------------------+-----------------------------------
Baseboard: |                            |
pre-D      |arm-realvie-eb-11mp         | arm-realview-eb-11mp-ctrevb
-----------+----------------------------+-----------------------------------
Baseboard: |                            |
D          |arm-realview-eb-11mp-bbrevd | arm-realview-eb-11mp-bbrevd-ctrevb
-----------+----------------------------+-----------------------------------
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The RealView EB baseboard revision D is a special case as it appears
to be undocumented in ARM official documents, while the Linux kernel
still contains special code for handling it.

commit be4f3c86
"Add RealView/EB support for the LAN9118 Ethernet chip"
adds support for the SMSC LAN9118 chip used on the D revision of
the baseboard, but no other traces of hardware deviations for this
variant can be found.

This creates a separate top-level .dts file especially for this
board version, so that it gets registered with the right type
of ethernet controller. The ethernet controller modifications
are then put into a separate .dtsi file so it can be overlaid
on other EB variants using the revision D baseboard.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on NXP i.MX53 SoC.

https://inversepath.com/usbarmorySigned-off-by: NAndrej Rosano <andrej@inversepath.com>
Tested-by: NVagrant Cascadian <vagrant@debian.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The NanoPi NEO is a minimal H3 based SBC. It comes with 256/512M RAM, a
micro SD slot, 10/100Mbit ethernet and a single USB-A port.
Signed-off-by: NJames Pettigrew <james@innovum.com.au>
Reviewed-by: NRask Ingemann Lambertsen <ccc94453@vip.cybercity.dk>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add the initial device tree for the RZ/A1 based development board (RSK).
Signed-off-by: NChris Brandt <chris.brandt@renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the initial device tree for the R8A7792  SoC based Wheat board.
The Wheat board itself has  no serial ports  wired up, the USB serial chips
are situated on a separate  debug board and  one of them is connected to
SCFI0  -- include unconditional support for  it, so that the serial console
can work.

Based  on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.

Note currently the dts is pretty much empty (except for including the
pc-plus dts), I've a local patch which enables the emac actually making
this dts different from the pc-plus one, but that needs the h3 emac
driver to get merged first.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

IMX6UL GEA M6UL modules are system on module solutions manufactured
by Engicam with following characteristics:
Processor	Freescale i.MX 6UltraLite MCIMX6G2, 528 MHz
RAM		128MB, 16-bit DDR3
NAND SLC	256MB
Power supply	Single 5V
MAX LCD RES	up to WXGA, 1366x768

and more info at
http://www.engicam.com/prodotti/embedded/som/sodimm/gea-m6ul

Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NMatteo Lisi <matteo.lisi@engicam.com>
Signed-off-by: NMichael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

B2260 board is the STMicroelectronics 96Board
based on STiH410 soc :
  - 1GB DDR
  - On-Board USB combo WiFi/Bluetooth RTL8723BU
    with PCB soldered antenna
  - Ethernet 1000-BaseT
  - Sata
  - HDMI
  - 2 x USB2 type A
  - micro USB2 type AB
  - SD card slot
  - High speed connector (SD/I2C/USB interfaces)
  - Slow speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Reviewed-by: NPeter Griffin <peter.griffin@linaro.org>

All UniPhier device trees have the common prefix "uniphier-", so
"ph1-" is just making names longer.  Recent documents and other
projects are not using PH1- prefixes any more.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

The inet-d978_rev2 is a pcb used in generic A33 based tablets. It features
volume buttons, micro-usb otg, headphone connector and a power button.

On the board a Realtek RTL8723BS SDIO Wi-Fi module are soldered, and there
is also a accompanied board which has a Goodix GT9271 soldered.

As this board is desired to create tablets with a Home key dealed by
GT9271, a LED is present at the front panel at the position of the
Home key.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a dts file for the Empire Electronix M712 tablet, this is a 7" A13
tablet, with micro-usb (otg), headphone and micro-sd slots on the
outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.

Note currently the dts for this is somewhat empty. This will change
once we add support for the touchscreen and accelerometer.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Raspberry Pi Zero is a minified version of model A+. It's
notable there is no PWR LED and the ACT LED is inverted.
Additionally the Pi Zero is capable of the USB peripheral mode.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This DTS file have support LG Nexus 5 (codenamed hammerhead).
Initial version have support for just serial console over headphone
jack.

Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: NBhushan Shah <bshah@kde.org>
Reviewed-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NAndy Gross <andy.gross@linaro.org>

Add a dts file for tablets using the generic inet-q972 PCB.

Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.

This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

A33-OLinuXino is A33 development board designed by Olimex LTD.

It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.

It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
Signed-off-by: NStefan Mavrodiev <stefan.mavrodiev@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

These device trees add support for TS-4900 by Technologic Systems.

More details here:
   http://wiki.embeddedarm.com/wiki/TS-4900Signed-off-by: NLucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The Gateworks Ventana GW553x is a single-board computer based on the NXP
IMX6 SoC with the following features:
 * IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
 * small form factor (35x70mm)
 * 512MB DDR3 DRAM (2x32bit) (options up to 2GB)
 * 256MB NAND flash (4GB option)
 * Gateworks System Controller:
  - hardware watchdog
  - hardware monitor
  - pushbutton controller
  - EEPROM storage
  - power control
 * JTAG programmable
 * 1x miniPCI socket (with PCIe, USB, SIM)
 * 1x microSD socket
 * 1x SIM socket
 * Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
 * analog CVBS video in
 * GPS (optional uBlox EVA-M8M)
 * Application headers:
  - 2x TTL UART (TX/RX)
  - 4x TTL GPIO (3x configurable as PWM)
  - 3x CVBS Analog video input (1x decoder with 3x selectable inputs)
 * Front panel connectors:
  - micro-HDMI audio/video out
  - 1x user programmable LED
  - 1x configurable user pushbutton
  - 1x USB OTG

See http://www.gateworks.com for more info
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The LCDK is the successor to the late Hawkboard.
Among the differences are the flash (16bits vs 8bits) and some pins
(MMC, LEDs, buttons, some external connectors), however the main
components remain the same (eth. phy, audio codec, video decoder and
DAC) except for the main PMIC, different and hard-wired on the LCDK (the
LDOs and DCDCs are always on).
A DT-only boot with this addition gives functional UART, reboot via
watchdog, RTC, ethernet and MMC (I added the CD GPIO for the MMC
although davinci_mmc doesn't call the OF facilities of mmc core).

Cc: Sekhar Nori <nsekhar@ti.com>
Tested-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NKarl Beldan <kbeldan@baylibre.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Add the initial support for the Warp7 board.

For more information about this reference design, please visit:

https://www.element14.com/community/docs/DOC-79058/l/warp-7-the-next-generation-wearable-reference-platformSigned-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Create a new device tree file for the Broadcom Northstar Plus
bcm958622hr SVK.  This SVK has 2GB RAM, 5 port Ethernet, 2 PCI slots,
and 1 UART.  Also, it has the ability to reboot via GPIO.  To be added
in the future are support for the USB and SLIC audio.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Create a new device tree file for the Broadcom Northstar Plus
bcm958623hr SVK.  This SVK has 2GB RAM, 5 ports Ethernet, SATA, 2 PCI
slots, and 1 UART.  Also, it has the ability to reboot via GPIO.  To be
added in the future are support for the USB and SLIC audio.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Create a new device tree file for the Broadcom Northstar Plus
bcm988312hr SVK.  This SVK has 2GB RAM, 5 ports Ethernet, 2 eSATA, 2 PCI
slots, and 1 UART.  Also, it has the ability to reboot via GPIO.  To be
added in the future is support for the USB.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Create a new device tree file for the Broadcom Northstar Plus
bcm958522er SVK.  This SVK has 2GB RAM, 2 ports Ethernet, 2 PCI slots,
and 1 UART.  Also, it has the ability to reboot via GPIO.  To be added
in the future is support for the USB.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Create a new device tree file for the Broadcom Northstar Plus
bcm958525er SVK.  This SVK has 2GB RAM, 2 ports Ethernet, 2 eSATA, 2 PCI
slots, and 1 UART.  Also, it has the ability to reboot via GPIO.  To be
added in the future is support for the USB.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[Maxime: Fix model and compatible]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Firefly RK3288 Reload is a combination Firefly rk3288 core board
with the Reload baseboard. Add a dtsi for the Firefly rk3288 core
which can be included into the dts for the various baseboards
in the future and dts for Reload base board.

Currently supported are serial console, wired networking, eMMC and
SD storage, SPFIF, IR receiver, LEDs, SDIO wifi and USB. But only
the OTG could work on the host mode now, the other USB host can't
work now, additional patches are required.
Signed-off-by: NRandy Li <ayaka@soulik.info>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This adds support for RK3288-Fennec boards. Currently supported
are serial console, wired networking, hdmi output and USB.
Signed-off-by: NXing Zheng <zhengxing@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The inet86dz board is a board used in 7" tablets from various oems.

These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Building both ARMv4 and ARMv5 dtbs when SOC_SAM_V4_V5 is an issue for
kernelci because it will then attempt to boot ARMv4 kernels on at91sam9
which doesn't work.

Use CONFIG_SOC_AT91RM9200 and CONFIG_SOC_AT91SAM9 instead.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

This patch adds the device tree to support Toradex Apalis TK1 a
computer on module which can be used on different carrier boards.

The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality which is not yet
supported. Anything that is not self contained on the module is disabled
by default.

The device tree for the Evaluation Board includes the module's device
tree and enables the supported peripherals of the carrier board (the
Evaluation Board supports almost all of them).
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The Banana Pi series is a well known series of single board computers.
The manufacturer, Sinovoip, is less well known. Moreover, the board
markings do not mention Sinovoip, but only the Banana Pi logo, and
the BPI-M* model name.

Rename the dts file to use the more well known name. Also fix up
some of the model names and labels to match other Banana Pi boards.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds the Cirrus Logic EP7209,EP7211 DT templates and support for
EDB7211 Development board.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>