The 8110SC rev d chip on our board shows a regression which the 8110SB chip
did not have. When inbound traffic is overflowing the receive descriptor queue,
"holes" in the ring buffer may occur which lead to a hangup until the buffer
is filled again. The packets are than completely processed, but the ring
remains porous and no packets are processed until the next overflow. Setting
the interface down and up can fix the problem temporary from userspace.

For some reason we don't know, this behaviour is not occuring if the RxVlan
bit for hardware VLAN untagging is set. There is another "Work around for
AMD plateform" in the current code which checks the VLAN status
word in receive descriptors, but does never come to effect when hardware
VLAN support is enabled. We assume that this is a bug in the chip.

The following patch fixes the problem. Without the patch we could reproduce
the hang within minutes (given other devices also generating lots of
interrupts), without we couldn't reproduce within a few days of long term
testing.

This version contains minor style adjustments and is sent with mutt which
will hopefully not destroy the formatting again.
Signed-off-by: NBernhard Schmidt <bernhard.schmidt@saxnet.de>
Signed-off-by: NSimon Wunderlich <simon.wunderlich@saxnet.de>
Acked-by: NFrancois Romieu <romieu@zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At this point (ri_tasklet()), RTNL or dev_base_lock are not held,
we must use dev_get_by_index() instead of __dev_get_by_index()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fixes the following build failure:
  CC      drivers/net/au1000_eth.o
/drivers/net/au1000_eth.c: In function 'au1000_set_settings':
/drivers/net/au1000_eth.c:623: error: implicit declaration of function 'capable'
/drivers/net/au1000_eth.c:623: error: 'CAP_NET_ADMIN' undeclared (first use in this function)
/drivers/net/au1000_eth.c:623: error: (Each undeclared identifier is reported only once
/drivers/net/au1000_eth.c:623: error: for each function it appears in.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve the reporting of myri10ge port type in ethtool,
and update for new boards.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NAndrew Gallatin <gallatin@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY on 82577/82578 parts needs a soft reset when transitioning to Sx
state in order for the PHY write which disables gigabit speed to take
effect.  Gigabit speed must be disabled in order for the PHY writes to
registers on page 800 (the wakeup control registers) to work as expected
otherwise the system might not wake via WoL.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Old code assumed board config version in the flash to be 1.
When this will get changed by tools, driver just refuses to
attach. This is unnecessary since driver does not have to
parse board config structure directly (maintained by firmware).
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clear NX_RESETING bit in netxen_tx_timeout_task() so that
the firmware watchdog task can catch need_reset request
from tx timeout.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid resetting subsys ID in i2c block. Also remove duplicate
check for address tranlsation error.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

niu: VLAN_ETH_HLEN should be used to make sure that the whole MAC header was copied to the head buffer in the Vlan packets case
Signed-off-by: NJoyce Yu <joyce.yu@sun.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In ks8851_set_rx_mode() the case handling IFF_MULTICAST was also setting
the RXCR1_AE bit by accident. This meant that all unicast frames where
being accepted by the device. Remove RXCR1_AE from this case.

Note, RXCR1_AE was also masking a problem with setting the MAC address
properly, so needs to be applied after fixing the MAC write order.

Fixes a bug reported by Doong, Ping of Micrel. This version of the
patch avoids setting RXCR1_ME for all cases.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MAC address register was being written in the wrong order, so add
a new address macro to convert mac-address byte to register address and
a ks8851_wrreg8() function to write each byte without having to worry
about any difficult byte swapping.

Fixes a bug reported by Doong, Ping of Micrel.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Issue a full soft reset at probe time.

This was reported by Doong Ping of Micrel, but no explanation of why this
is necessary or what bug it is fixing. Add it as it does not seem to hurt
the current driver and ensures that the device is in a known state when we
start setting it up.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fec_enet_init is called by both fec_probe and fec_resume, so it
shouldn't be marked as __init.
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixed the problem of dropped packets due to lost of
interrupt requests. We should only clear what was pending at the
moment we read the irq source reg.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vmxnet3 was using dprintk() for debugging output.  This was
defined in <linux/dst.h> and was the only thing that was
used from that header file.  This caused compile errors
when CONFIG_BLOCK was not enabled due to bio* and BIO*
uses in the header file, so change this driver to use
dev_dbg() for debugging output.

include/linux/dst.h:520: error: dereferencing pointer to incomplete type
include/linux/dst.h:520: error: 'BIO_POOL_BITS' undeclared (first use in this function)
include/linux/dst.h:521: error: dereferencing pointer to incomplete type
include/linux/dst.h:522: error: dereferencing pointer to incomplete type
include/linux/dst.h:525: error: dereferencing pointer to incomplete type
make[4]: *** [drivers/net/vmxnet3/vmxnet3_drv.o] Error 1
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NBhavesh Davda <bhavesh@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because netpoll can call netdevice start_xmit() method with
irqs disabled, drivers should not call kfree_skb() from
their start_xmit(), but use dev_kfree_skb_any() instead.

Oct  8 11:16:52 172.30.1.31 [113074.791813] ------------[ cut here ]------------
Oct  8 11:16:52 172.30.1.31 [113074.791813] WARNING: at net/core/skbuff.c:398 \
                skb_release_head_state+0x64/0xc8()
Oct  8 11:16:52 172.30.1.31 [113074.791813] Hardware name:
Oct  8 11:16:52 172.30.1.31 [113074.791813] Modules linked in: netconsole ocfs2 jbd2 quota_tree \
ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm ocfs2_nodemanager ocfs2_stackglue configfs crc32c drbd cn loop \
serio_raw psmouse snd_pcm snd_timer snd soundcore snd_page_alloc virtio_net pcspkr parport_pc parport \
i2c_piix4 i2c_core button processor evdev ext3 jbd mbcache dm_mirror dm_region_hash dm_log dm_snapshot \
dm_mod ide_cd_mod cdrom ata_generic ata_piix virtio_blk libata scsi_mod piix ide_pci_generic ide_core \
                virtio_pci virtio_ring virtio floppy thermal fan thermal_sys [last unloaded: netconsole]
Oct  8 11:16:52 172.30.1.31 [113074.791813] Pid: 11132, comm: php5-cgi Tainted: G        W  \
                2.6.31.2-vserver #1
Oct  8 11:16:52 172.30.1.31 [113074.791813] Call Trace:
Oct  8 11:16:52 172.30.1.31 [113074.791813] <IRQ>  [<ffffffff81253cd5>] ? \
                skb_release_head_state+0x64/0xc8
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81253cd5>] ? skb_release_head_state+0x64/0xc8
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81049ae1>] ? warn_slowpath_common+0x77/0xa3
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81253cd5>] ? skb_release_head_state+0x64/0xc8
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81253a1a>] ? __kfree_skb+0x9/0x7d
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffffa01cb139>] ? free_old_xmit_skbs+0x51/0x6e \
                [virtio_net]
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffffa01cbc85>] ? start_xmit+0x26/0xf2 [virtio_net]
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8126934f>] ? netpoll_send_skb+0xd2/0x205
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffffa0429216>] ? write_msg+0x90/0xeb [netconsole]
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81049f06>] ? __call_console_drivers+0x5e/0x6f
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8102b49d>] ? kvm_clock_read+0x4d/0x52
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8104a082>] ? release_console_sem+0x115/0x1ba
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8104a632>] ? vprintk+0x2f2/0x34b
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8106b142>] ? vx_update_load+0x18/0x13e
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81308309>] ? printk+0x4e/0x5d
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8102b49d>] ? kvm_clock_read+0x4d/0x52
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81070b62>] ? getnstimeofday+0x55/0xaf
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81062683>] ? ktime_get_ts+0x21/0x49
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff810626b7>] ? ktime_get+0xc/0x41
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81062788>] ? hrtimer_interrupt+0x9c/0x146
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81024a4b>] ? smp_apic_timer_interrupt+0x80/0x93
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81011663>] ? apic_timer_interrupt+0x13/0x20
Oct  8 11:16:52 172.30.1.31 [113074.791813] <EOI>  [<ffffffff8130a9eb>] ? _spin_unlock_irq+0xd/0x31
Reported-and-tested-by: NMassimo Cetra <mcetra@navynet.it>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Bug-Entry: http://bugzilla.kernel.org/show_bug.cgi?id=14378Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before issuing any cmds to the FW, the driver must first wait
till the fW becomes ready. This is needed for PCI hot plug when
the driver can be probed while the card fw is being initialized.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vmxnet3 uses in_dev* interfaces so it should depend on INET.
Also fix so that the driver builds when CONFIG_PCI_MSI is disabled.

vmxnet3_drv.c:(.text+0x2a88cb): undefined reference to `in_dev_finish_destroy'

drivers/net/vmxnet3/vmxnet3_drv.c:1335: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:1384: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2137: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2138: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NBhavesh davda <bhavesh@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the driver for the ST MAC 10/100/1000 on-chip Ethernet
controllers (Synopsys IP blocks).

Driver documentation:
 o http://stlinux.com/drupal/kernel/network/stmmac
Revisions:
 o http://stlinux.com/drupal/kernel/network/stmmac-driver-revisions
Performances:
 o http://stlinux.com/drupal/benchmarks/networking/stmmacSigned-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Randy Dunlap <randy.dunlap@oracle.com>

ks8851_mll uses mii interfaces so it needs to select MII.

ks8851_mll.c:(.text+0xf95ac): undefined reference to `generic_mii_ioctl'
ks8851_mll.c:(.text+0xf96a0): undefined reference to `mii_ethtool_gset'
ks8851_mll.c:(.text+0xf96fa): undefined reference to `mii_ethtool_sset'
ks8851_mll.c:(.text+0xf9754): undefined reference to `mii_link_ok'
ks8851_mll.c:(.text+0xf97ae): undefined reference to `mii_nway_restart'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MDIO bus cannot be accessed at interrupt context, but on an FEC
error, the fec_mpc52xx driver reset function also tries to reset the
PHY.  Since the error is detected at IRQ context, and the PHY functions
try to sleep, the kernel ends up panicking.

Resetting the PHY on an FEC error isn't even necessary.  This patch
solves the problem by removing the PHY reset entirely.
Signed-off-by: NJohn Bonesio <bones@secretlab.ca>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some OF platform drivers are missing module device tables, so they won't
load automatically on boot. This patch fixes the issue by adding proper
MODULE_DEVICE_TABLE() macros to the drivers.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mechanism to clear the statistics register is dependent
on the status of GMIIEN bit in MAC control register. If the
GMIIEN bit is set, the stats registers are write to decrement.
If the GMIIEN bit is cleared, the stats registers are plain
read/write registers. The stats register clearing operation
must take into account the current state of GMIIEN as it
can be cleared when the interface is brought down.

With existing implementation logic, querying for interface stats
when the interface is down, can corrupt the statistics counters.
This patch examines the GMIIEN bit status in MAC_CONTROL
register before choosing an appropriate mask for clearing stats
registers.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Acked-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extracted from Realtek's 8.012.00 r8168 driver.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NSimon Farnsworth <simon.farnsworth@onelan.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cisco HDLC uses keepalive packets and sequence numbers to determine link
state. In rare cases both ends could transmit keepalive packets at the same
time, causing the received sequence numbers to be treated as incorrect.
Now we accept our current sequence number as well as the previous one.
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

3c574_cs:
 spin_lock the set_multicast_list function.
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Belkin F8T012xx1 bluetooth adaptor has the same vendor and product
IDs as the Belkin F5D5050, so we need to teach the pegasus driver to
ignore adaptors belonging to the "Wireless" class 0xE0. For this one
case anyway, seeing as pegasus is a driver for "Wired" adaptors.
Signed-off-by: NChris Rankin <rankincj@yahoo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use resource_size_t for PCI resource remapping instead
of unsigned long. Physical addresses can exceed range of
long data type (e.g with PAE).
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethoc.c: In function ‘ethoc_open’:
drivers/net/ethoc.c:667: warning: comparison of distinct pointer types
lacks a cast
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethernet NIC driver for VMware's vmxnet3

From: Shreyas Bhatewara <sbhatewara@vmware.com>

This patch adds driver support for VMware's virtual Ethernet NIC: vmxnet3
Guests running on VMware hypervisors supporting vmxnet3 device will thus have
access to improved network functionalities and performance.
Signed-off-by: NShreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NBhavesh Davda <bhavesh@vmware.com>
Signed-off-by: NRonghua Zhang <ronghua@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IXP 2000 network driver was failing to build as it has its own
statistics gathering which was not compatible with the recent network
device operations changes. This patch fixes the driver in the obvious
way and has been compile tested. I have been unable to get the ixp2000
maintainer to comment or test this fix.
Signed-off-by: NVincent Sanders <vince@simtec.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to the way it interacts with the networking
stack and other parts of mac80211, ieee80211_rx()
must be called with disabled softirqs.

[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/39440/focus=40266Reported-by: NDave Young <hidave.darkstar@gmail.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Need to free the dynamic allocated memory before ieee80211_free_hw();
once call ieee80211_free_hw(), should not reference to "priv" data
structure.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If ace_load_firmware() fails, ace_init() cleans up but still returns
0, leading to an oops as seen in <http://bugs.debian.org/521383>.
It should pass the error code up.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need PHY drivers to initialize in a static kernel before
the MAC drivers that use them.  So link them in first.

Based upon a report by Felix Radensky.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>