Several sas drivers legitimately check the protocol against the union of
SAS_PROTOCOL_SATA and SAS_PROTOCOL_STP.  Provide a SAS_PROTOCOL_STP_ALL
to silence warnings like:

drivers/scsi/pm8001/pm8001_sas.c:438:3: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
drivers/scsi/mvsas/mv_sas.c:798:2: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
drivers/scsi/mvsas/mv_sas.c:1783:2: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
drivers/scsi/mvsas/mv_sas.c:1886:2: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
drivers/scsi/isci/request.c:3565:2: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Allow expander table-to-table attachments for
expanders that support it.
Signed-off-by: NLuben Tuikov <ltuikov@yahoo.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add SFF-8485 v0.7 / SAS-1 smp-write-gpio register support to libsas.
Defer SAS-2 support unless/until it defines an sgpio interface.

Minimum implementation needed to get the lights blinking.
try_test_sas_gpio_gp_bit() provides a common method to parse the
incoming write data (raw bitstream), and the to_sas_gpio_gp_bit() helper
routine can be used as a basis for the set/clear operations for the
'read' implementation.  Host implementations parse as many bits
(ODx.[012]) as are locally supported and report the number of registers
successfully written.  If the submitted data overruns the internal
number of registers available report the write as a success with the
number of bytes remaining reported in ->resid_len.

Example (assuming an active backplane) set the "identify" pattern for
the first 21 devices:

smp_write_gpio --count=2 --data=92,49,24,92,24,92,49,24 -t 4 --index=1 /dev/bsg/sas_hostX
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

sparse complains about the mixing of enums in libsas.  Since the
underlying numeric values of both enums are the same, combine them
to get rid of the warning.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch implements the ability to set the minimum and maximum
linkrates for both libsas (for expanders) and aic94xx (for the host
phys).  It also tidies up the setting of the hardware min and max to
make sure they're updated when the expander emits a change broadcast.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

At the moment we have two separate linkspeed enumerations covering
roughly the same values.  This patch consolidates on a single one enum
sas_linkspeed in scsi_transport_sas.h and uses it everywhere in the
aic94xx driver.  Eventually I'll get around to removing the duplicated
fields in asd_sas_phy and sas_phy ...
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This is the end point of the separate aic94xx driver based on the
original driver and transport class from Luben Tuikov
<ltuikov@yahoo.com>

The log of the separate development is:

Alexis Bruemmer:
  o aic94xx: fix hotplug/unplug for expanderless systems
  o aic94xx: disable split completion timer/setting by default
  o aic94xx: wide port off expander support
  o aic94xx: remove various inline functions
  o aic94xx: use bitops
  o aic94xx: remove queue comment
  o aic94xx: remove sas_common.c
  o aic94xx: sas remove depot's
  o aic94xx: use available list_for_each_entry_safe_reverse()
  o aic94xx: sas header file merge

James Bottomley:
  o aic94xx: fix TF_TMF_NO_CTX processing
  o aic94xx: convert to request_firmware interface
  o aic94xx: fix hotplug/unplug
  o aic94xx: add link error counts to the expander phys
  o aic94xx: add transport class phy reset capability
  o aic94xx: remove local_attached flag
  o Remove README
  o Fixup Makefile variable for libsas rename
  o Rename sas->libsas
  o aic94xx: correct return code for sas_discover_event
  o aic94xx: use parent backlink port
  o aic94xx: remove channel abstraction
  o aic94xx: fix routing algorithms
  o aic94xx: add backlink port
  o aic94xx: fix cascaded expander properties
  o aic94xx: fix sleep under lock
  o aic94xx: fix panic on module removal in complex topology
  o aic94xx: make use of the new sas_port
  o rename sas_port to asd_sas_port
  o Fix for eh_strategy_handler move
  o aic94xx: move entirely over to correct transport class formulation
  o remove last vestages of sas_rphy_alloc()
  o update for eh_timed_out move
  o Preliminary expander support for aic94xx
  o sas: remove event thread
  o minor warning cleanups
  o remove last vestiges of id mapping arrays
  o Further updates
  o Convert aic94xx over entirely to the transport class end device and
  o update aic94xx/sas to use the new sas transport class end device
  o [PATCH] aic94xx: attaching to the sas transport class
  o Add missing completion removal from prior patch
  o [PATCH] aic94xx: attaching to the sas transport class
  o Build fixes from akpm

Jeff Garzik:
  o [scsi aic94xx] Remove ->owner from PCI info table

Luben Tuikov:
  o initial aic94xx driver

Mike Anderson:
  o aic94xx: fix panic on module insertion
  o aic94xx: stub out SATA_DEV case
  o aic94xx: compile warning cleanups
  o aic94xx: sas_alloc_task
  o aic94xx: ref count update
  o aic94xx nexus loss time value
  o [PATCH] aic94xx: driver assertion in non-x86 BIOS env

Randy Dunlap:
  o libsas: externs not needed

Robert Tarte:
  o aic94xx: sequence patch - fixes SATA support
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>