DWC3 revisions <1.90a have an issue which would cause
a missing USB3 Reset event. In such cases, it's
suggested that we follow the steps of a normal
USB3 Reset on Connection Done Event.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

RTL revisions <1.83a have an issue where, depending
on the link partner, the USB link might do multiple
entry/exit of low power states before a transfer
takes place causing degraded throughput.

The suggested workaround is to clear bits
12:9 of DCTL register if we see a transition
from U1|U2 to U0 and only re-enable that on
a transfer complete IRQ and we have no pending
transfers on any of the enabled endpoints.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch avoids the compiler spitting out the following warning:
|drivers/usb/dwc3/gadget.c:1304: warning: 'trb' is used uninitialized \
	in this function

This is only uninitialized if the list of to-cleanup TRBs is empty which
should not be the case because we call this functions once a transfer
completed so it should be on list.

In order to make the warning disappear we return early. This should
never happen and the WARN_ON_ONCE(1) is there in case it happens
so we can investigate what went wrong.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since the re-worked ep0 handling (which uses HW's hints to recognize the ep0
status) we lost the delayed status handling. This is used by the file and mass
storage gadget to gain some extra time so setup its internal status before it
can proceed further requests.
In particular the storage gadget does nothing on USB_REQ_SET_CONFIGURATION but
wakes up a thread which handles the request. If the udc driver continues ep0
handling before the thread did its work then then endpoint is not yet
configured and further requests will fail. Once the gadget is ready, it will
enqueue an empty packet which is used for synchronization.
In order to fix this issue, the patch does the following:
Set ->delayed_status once the delayed_status has been notices and do not
continue on the next XferNotReady event. We will continues ep0 processing once
the gadget enqueued the zero packet for synchronization.

A cleaner approach would be to enforce the gadget to enqueue an empty
(zero) request even for the status phase but this would do for now.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We wait for the XferNotReady before we start the transfer and by then we
know ep0 state in which we supposed to be.
This is some cleanup work for the following patch in which we require to
know the ep0 state before the transfer completes.
While here, also change the argument to dwc3_ep0_do_control_status() so
we don't require the complete event structure but only the required
piece of information.
Inspired-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

sparse caught three mistakes on this driver,
fix them:

drivers/usb/dwc3/ep0.c:806:29: warning: duplicate const
drivers/usb/dwc3/debugfs.c:481:15: warning: symbol 'dwc3_debugfs_init' \
	was not declared. Should it be static?
drivers/usb/dwc3/debugfs.c:518:16: warning: symbol 'dwc3_debugfs_exit' \
	was not declared. Should it be static?
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There were a few coding style issues with this driver
which are now fixed:

drivers/usb/dwc3/debugfs.c:48: WARNING: Use #include \
	<linux/uaccess.h> instead of <asm/uaccess.h>
drivers/usb/dwc3/debugfs.c:484: ERROR: space required \
	before the open brace '{'
drivers/usb/dwc3/ep0.c:261: WARNING: line over 80 characters
drivers/usb/dwc3/ep0.c:287: WARNING: suspect code indent \
	for conditional statements (16, 23)
drivers/usb/dwc3/gadget.c:749: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.c:1267: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.h:116: WARNING: line over 80 characters
drivers/usb/dwc3/io.h:42: WARNING: Use #include \
	<linux/io.h> instead of <asm/io.h>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

A few inits like the scale value or the removal of the DISSCRAMBLE is
done in the gadget code however it touches a general register.
Move this piece to the core.c file since it is likely to be requied by
both, parts of the core (device and host).
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There are two where need to set operational mode:
- during initialization while we decide to run in host,device or DRD
  mode
- at runtime via the debugfs interface.

This patch provides a new function which sets the operational mode and
moves its initialiation to the mode switch instead in the gadget code
itself.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In "usb: dwc3: remove special status request handling in ep0" I simplied
a few things and used the generic API for the status transfers. The bug
I introcuded here is that we queue now requests to dep[1] but we don't
clear that list in the stall+start case.
Actually we don't need to use dep[1] at all. We only did in the past to
talk to the correct endpoint (i.e. in or out). This is now take care of
in a diffent place within the ep0 code. So we could queue the in
transfers to dep[0] and don't use dep[1] at all.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The first access was correct, the second was wrong.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

hardware will tell us how many event buffers we
need to support, so let's allocate the array
dynamically too.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

if we ever have an omap with multiple instances of
the DWC3 IP, we need unique names for them. In order
to achieve that, let's use the dwc3_get/put_device_id()
calls to give us an unique device identifier.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

if we want to support situations where we have
both SoC and PCIe versions of the IP on the same
platform, we need to have sequential numbers between
them, otherwise we will still have name collisions.

Because of that, we need to move dwc3_get/put_device_id()
to core.c and export that symbol to be used by glue
layers.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The GetStatus (STD)-request is handled the driver and uses a tiny hack
to send the two bytes long answer. This patch removes the custom hack
uses the normal usb_ep_queue() for that.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If we stall and restart we have to reset also this flag to 0 as there is
nothing pending anymore.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

None of these are required atm.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The read and write operation is atomic and we need no locking around
this operations. What we need however is a lock that is held which
ensures that the content of the DWC3_GCTL has not been changed. With
this, the conten may have been change changed after the first but before
our write back.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We can have three modules here: dwc3.ko, dwc3-omap.ko and dwc3-pci.ko.
The later have already ids-aliases for probing and is fine. The omap
module has alias for DT but lacks alias for the "native"
platform_device. Maybe we should get rid of it and stick to the DT name?
Both glue modules create a new device for which the dwc3.ko module is
responsible and that one lacks the platform alias.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Sometimes the host might be trying to initiate Data or
Status phase for an older Control transfer. In such
situations we must STALL that transfer and restart
the state machine rather than letting such situation
go through the wire.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This makes testing a lot easier when trying to
switch between host and device modes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

I have talked to USB-IF about USB30CV issuing SetAddres()
with a device on Configured state and they have agreed on
changing USB30CV not to do so.

Adding back the STALL reply in such case and while at
that, also add a debugging message for an address which
is too large.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

now that we have host support, we must depend
on both sides.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

host prototypes are there, let's move gadget's
closer.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We can decide in runtime if that will be used
or not.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The Designware USB3 IP can be configured with
an internal xHCI. If we're running on such a
version, let's start the xHCI stack.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There's no need to add driver_data for something
we can fetch from HW.

This also makes our id_table unnecessary - at least
for now -, so we also remove it on the same patch.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This will allow us to only allocate memory when
we actually need.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this is mainly for testing. In order to be able
to test if we're enumerating correctly on all
speeds, let that be controlled by a module
parameter.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

when we remove the gadget driver, it will already
do that for us.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts commit df711fc9.

The commit added a reset-on-resume quirk because the NEC chipset stopped
responding to commands about 30 minutes after a system resume from
suspend.  We thought it was a chipset issue, but it turns out that the
xHCI driver was zeroing out the link TRB after a successful context
restore during resume.  The host controller would fall off the command
ring sometime later, causing it to not respond to new commands.

The link TRB issue has been fixed with commit
158886cd "xHCI: fix bug in
xhci_clear_command_ring()", so revert the reset-on-resume quirk, as it's
not necessary.

Commit df711fc9 was marked for stable
trees back to 2.6.37, but according to my mail, it has not made it into
Linus' tree or the stable trees yet.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NJulian Sikorski <belegdol@gmail.com>
Cc: Andiry Xu <andiry.xu@amd.com>

When system enters suspend, xHCI driver clears command ring by writing zero
to all the TRBs. However, this also writes zero to the Link TRB, and the ring
is mangled. This may cause driver accesses wrong memory address and the
result is unpredicted.

When clear the command ring, keep the last Link TRB intact, only clear its
cycle bit. This should fix the "command ring full" issue reported by Oliver
Neukum.

This should be backported to stable kernels as old as 2.6.37, since the
commit 89821320 "xhci: Fix command ring replay after resume" is merged.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NOliver Neukum <oneukum@suse.de>

The original implementation of dequeuing a request in progress
is not correct.  Change to use a correct process and also clean
up the related functions a little bit.
Signed-off-by: NLi Yang <leoli@freescale.com>
Acked-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In order to support multiple SoC kernel image, compile-time dependency
on a specific SoC type should be avoided.

fsl_udc_clk_finalize is already protected by cpu_is_mx35(), so remove
the compile-time check for CONFIG_SOC_IMX35.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the following build error:

CC [M]  drivers/usb/gadget/fsl_mxc_udc.o
drivers/usb/gadget/fsl_mxc_udc.c: In function 'fsl_udc_clk_finalize':
drivers/usb/gadget/fsl_mxc_udc.c:98: error: implicit declaration of function 'readl'
drivers/usb/gadget/fsl_mxc_udc.c:100: error: implicit declaration of function 'writel'

This error is caused by the follwing commit:
(16fcb63: arm/imx: remove mx31_setup_weimcs( ) from mx31.h)

,which removed '#include <linux/io.h>' from mx31.h.

fsl_mxc_udc.c includes <mach/hardware.h>, which in turns includes mx31.h, so
that's the reason fsl_mxc_udc.c built fine previously.

Instead of relying on the indirect inclusion of the linux/io.h header file,
include it directly in fsl_mxc_udc.c.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some ISO gadgets, like audio, has SYNC attribute as well as
USB_ENDPOINT_XFER_ISOC for their bmAttributes at ISO endpoint
descriptor. So, it needs to use usb_endpoint_xfer_isoc to judge
ISO XFER.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Acked-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Several UDC drivers had a gadget driver's speed sanity check of the
form of:

	driver->speed != USB_SPEED_HIGH

or:

	driver->speed != USB_SPEED_HIGH && driver->speed != USB_SPEED_FULL

As more and more gadget drivers support USB SuperSpeed, driver->speed
may be set to USB_SPEED_SUPER and UDC driver should handle such gadget
correctly.  The above checks however fail to recognise USB_SPEED_SUPER
as a valid speed.

This commit changes the two checks to:

	driver->speed < USB_SPEED_HIGH

or:

	driver->speed < USB_SPEED_FULL

respectively.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Reported-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit "usb: gadget: use config_ep_by_speed() instead of
ep_choose()" broke g_serial in "non ACM nor OBEX"
mode. Apply a trivial fix on usb endpoints discovery.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch cares latest USB_SPEED_SUPER support.
renesas_usbhs can not use super-speed, but can use full/high speed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>