The CPGMAC pin list in da850.c was incorrectly split into two MII/RMII mode
specific pin lists, while what pin group is used is a function of how the board
is wired.  Copy the pin lists to board-da850-evm.c, renaming them accordingly,
and merge the two lists in da850.c into one, da850_cpgmac_pins[], representing
the CPGMAC module as a whole...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: NBen Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The NAND/NOR flash pin lists (da850_nand_pins/da850_nor_pins) are purely board
specific and as such shouldn't be in da850.c -- copy them to board-da850-evm.c,
renaming to da850_evm_nand_pins/da850_evm_nor_pins respectively, and merge the
two lists in da850.c into one, representing the EMIF 2.5 module as a whole,
just like we have it in da830.c...

While at it, remove the '__init' modifier from da850_evm_setup_nor_nand() as
this function is called from non '__init' code...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: NBen Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Keep PLL0 SYSCLK3 at a constant rate of 100MHz. This enables the AEMIF
timing to remain valid even as the PLL0 output is changed by cpufreq
driver to save power.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The drivers on da8xx/omapl EVMs do not utilize all the channels
and slots provided by EDMA. Some of these are better utilitzed by
the DSP on the SoC for speeding up codec operations.

Reserve these channels/slots for the DSP.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The earlier watchdog reset mechanism had a couple of limitations.  First, it
embedded a reference to "davinci_wdt_device" inside common code.  This
forced all derived platforms (da8xx and tnetv107x) to define such a device.
This also would have caused problems in including multiple socs in a single
build due to symbol redefinition.

With this patch, davinci_watchdog_reset() now takes the platform device as an
argument.  The davinci_soc_info struct has been extended to include a reset
function and a watchdog platform_device.  arch_reset() then uses these
elements to reset the system in a SoC specific fashion.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Tested-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Pinmux registers are sequential, and do not need to be enumerated out as they
currently are.  This reduces code volume and keeps things simple.

If some future SoC comes up with a discontiguous register map, PINMUX() can
then be expanded with local token pasting.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Rename da8xx_pinmux_setup() to davinci_cfg_reg_list() and promote it for use in
other SOCs that may need the ability to configure multiple pins in one shot.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This hushes the following warning:

arch/arm/mach-davinci/include/mach/da8xx.h:104: warning: ‘struct platform_device’
declared inside parameter list
arch/arm/mach-davinci/include/mach/da8xx.h:104: warning: its scope is only this
definition or declaration, which is probably not what you want
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The da8xx/omap-l1 boards refuse to build when CONFIG_DAVINCI_MUX is undefined
because arch/arm/mach-davinci/mux.c:da8xx_pinmux_setup() is not defined.

This patch fixes this issue. This is build tested with davinci_all_defconfig
and da8xx_omapl_defconfig and boot tested on DA830 EVM.
Reported-by: NShanmuga Sundaram Mahendran <shanmuga@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds support for registering for suspend-to-RAM
functionality on da850/omap-l138 SoCs.

da850 supports wakeup based on external event and RTC
alarm.

Currently only RTC alarm based wakeup is supported.
Support for wakeup based on external event will be
added as later improvements.

For scheduling an alarm event on RTC some useful code
is present in Documentation/rtc.txt
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The davinci EMAC peripheral is also available on other TI
platforms -notably TI AM3517 SoC. This patch modifies the
config option and the platform structure header files so that
the driver can be reused on non-davinci platforms as well.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Acked-by: NChaithrika U S <chaithrika@ti.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Create static map for internal SRAM and populate SRAM base
and size in soc_info structure to allow SRAM allocation
functions from arch/arm/mach-davinci/sram.c to work.

On DA850 SRAM is used for suspend-to-RAM implementation
in places where DDR2 cannot be accessed as its clocks are
stopped.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

When suspend is supported, both cpuidle and suspend code
need to work on DDR2 registers. Instead of mapping the
DDR2 registers twice, do it once outside of cpuidle
driver and let cpuidle driver get the virtual base address
of DDR2 registers.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

OMAP-L138 adds a second SYSCFG region having useful functionality
like deep sleep, pull up/down control and SATA clock stop.

This patch makes provision for accessing registers from second
SYSCFG region in da8xx code.

Note that OMAP-L137 has a single SYSCFG region.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch provides a function to help register cpuidle driver
on da8xx/omap-l1xx platforms.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add the function to register the MUSB platform device.
Additional compile warning fixes by Sekhar Nori.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

DA850/OMAP-L138 EVM has a RMII Ethernet PHY on the UI daughter card. The PHY
is enabled by proper programming of the IO Expander (TCA6416) ports. Also for
RMII PHY to work, the MDIO clock of MII PHY has to be disabled since both the
PHYs have the same address. This is done via the GPIO2[6] pin. This patch adds
support for RMII PHY.

This patch also adds a menuconfig option to select one or no peripheral
connected to expander. Currently, sub-options in this menu are RMII and no
peripheral.This menuconfig option is similar to the one present for UI card on
DA830/OMAP-L137 EVM.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Adds basic frequency scaling support for DA850/OMAP-L138.

Currently, frequency scaling only on PLL0 is supported. No scaling of PLL1
as yet.

Peripherals like MMC/SD which have a clock input synchronous with
ARM clock will not work well since the clock will change behind their backs.
Support for notification to such devices to adjust themselves to the
new frequency will be added in later patches. Current defconfigs keep
CPUFreq disabled so it will not affect normal operation.

The OPP defintions assume clock input of 24MHz to the SoC. This is inline
with hardcoding of input frequency in the <soc>.c files. At some point
this will need to move into board dependent code as new boards appear with
a different reference clock.

Tested on OMAP-L138 EVM with ondemand governer and a shell script to
vary processor load.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add the function to register the OHCI platform device, given the root hub
related platform data passed from the board  specific code.  The platfrom
data provide for overriding the OHCI port power and over-current bits at
the board level.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

These are needed by the MUSB and OHCI glue layers...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add RTC support for the da830/omap-l137 and da850/omap-l138
SoC's by leveraging existing the rtc-omap driver.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add support for the Sharp LCD035Q3DG01 graphical LCD.  This
requires a minor interface change to da8xx_register_lcdc()
so that the board code can pass in the platform_data which
describes the lcd controller that's to be used.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The patch allows Async3 clock source to be selected between PLL1 SYSCLK2
and PLL0 SYSCLK2.

Having Async3 source from PLL1 SYSCLK2 allows peripherals on that
domain to remain unaffected by frequency scaling on PLL0.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This makes it clear that JTAG ID register is part of the
SYSCFG module
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Avoid use of IO_ADDRESS() for SYSCFG module by doing an ioremap() instead.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Rename the DA8XX_BOOT_CFG_BASE macro to get it in line
with the public documentation for these parts.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

For consistency with existing code, change the name of
da8xx_init_mcasp() to da8xx_register_mcasp().
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds platform data for the 8MB NOR flash
found on da850/omap-l138 EVM. Both NOR and NAND can
co-exist on da850/omap-l138 as they are using different
chip selects.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds platform data for the 512MB NAND Flash
found on DA850/OMAP-L138 EVM. Currently it supports
only 1-bit ECC.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

There are two instances of MMC/SD on da850/omap-l138.
Connector for the first instance is available on the
EVM. This patch adds support for this instance.

This patch also adds support for card detect and write
protect switches on da850/omap-l138 EVM.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds platform support for the graphic display
(Sharp LK043T1DG01) found on DA850/OMAP-L138 based EVM.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Define resources for McASP1 used on DA830/OMAP-L137 EVM, add platform
device defintion, initialization function.  Additionally, this patch
also adds version and FIFO related members to platform data structure.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Ethernet Media Access Controller (EMAC) on da850/omap-l138
supports 10/100 Mbps operation. It also supports Media
Independent Interface (MII) and Reduced Media Independent
Interface (RMII) to physical layer (PHY).

Phy which supports MII is present on the DA850/OMAP-L138
base board and Phy supporting RMII is present on the
UI card. This patch adds support only for the MII Phy.
Support for RMII Phy will be added later.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The DA850/OMAP-L138 is a new SoC from TI in the same family as
DA830/OMAP-L137.

Major changes include better support for power management,
support for SATA devices and McBSP (same IP as DM644x).

DA850/OMAP-L138 documents are available at
http://focus.ti.com/docs/prod/folders/print/omap-l138.html.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Rearrange the PINMUX macros and pinmux_setup function which
are common between da830/omap-l137 and da850/omap-l138.

Also, replace the da830 string in function names to da8xx.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

With the introduction of TI da850/omap-l138, some of the macros
defined for da830/omap-l137 will be needed in da850 source file.
So, move the common macros to da8xx.h header file.

Also, modify the macro names from DA830_... to DA8XX_.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The da830/omap l137 is a new SoC from TI that is similar
to the davinci line.  Since its so similar to davinci,
put the support for the da830 in the same directory as
the davinci code.

There are differences, however.  Some of those differences
prevent support for davinci and da830 platforms to work
in the same kernel binary.  Those differences are:

1) Different physical address for RAM.  This is relevant
   to Makefile.boot addresses and PHYS_OFFSET.  The
   Makefile.boot issue isn't truly a kernel issue but
   it means u-boot won't work with a uImage including
   both architectures.  The PHYS_OFFSET issue is
   addressed by the "Allow for runtime-determined
   PHYS_OFFSET" patch by Lennert Buytenhek but it
   hasn't been accepted yet.

2) Different uart addresses.  This is only an issue
   for the 'addruart' assembly macro when CONFIG_DEBUG_LL
   is enabled.  Since the code in that macro is called
   so early (e.g., by _error_p in kernel/head.S when
   the processor lookup fails), we can't determine what
   platform the kernel is running on at runtime to use
   the correct uart address.

These areas have compile errors intentionally inserted
to indicate to the builder they're doing something wrong.

A new config variable, CONFIG_ARCH_DAVINCI_DMx, is added
to distinguish between a true davinci architecture and
the da830 architecture.

Note that the da830 currently has an issue with writeback
data cache so CONFIG_CPU_DCACHE_WRITETHROUGH should be
enabled when building a da830 kernel.

Additional generalizations for future SoCs in the da8xx family done by
Sudhakar Rajashekhara and Sekhar Nori.
Signed-off-by: NSteve Chen <schen@mvista.com>
Signed-off-by: NMikhail Cherkashin <mcherkashin@ru.mvista.com>
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>