With -ffunction-section the entries in __dbe_table aren't no longer
sorted, so the lookup of exception addresses in do_be() failed for
some addresses. To avoid this we now sort __dbe_table.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When calibration against PIT fails, the warning that we print is misleading.
In a virtualized environment the VM may get descheduled while calibration
or, the check in PIT calibration may fail due to other virtualization
overheads.

The warning message explicitly assumes that calibration failed due to SMI's
which may not be the case. Change that to something proper.
Signed-off-by: NAlok N Kataria <akataria@vmware.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The TSC calibration function is still very complicated, but this makes
it at least a little bit less so by moving the PIT part out into a
helper function of its own.
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-of-by: NLinus Torvalds <torvalds@linux-foundation.org>

The calculation to get TI_CPU based off of SPRG3 was just plain wrong,
meaning that we were getting garbage for the CPU number on 6xx/G3/G4
based SMP boxes in this code.

Just offset off the stack pointer (to get to thread_info) like all the
other references to TI_CPU do.

This was pointed out by Chen Gong <G.Chen@freescale.com>

[paulus@samba.org - use rlwinm r12,r11,... instead of
 rlwinm r12,r1,...; tophys()]
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

HAVE_ARCH_UNMAPPED_AREA and HAVE_ARCH_UNMAPPED_AREA_TOPDOWN must
be defined whenever CONFIG_PPC_MM_SLICES is enabled, not just when
CONFIG_HUGETLB_PAGE is.  They used to be always defined together but
this is no longer the case since 3a8247cc
("powerpc: Only demote individual slices rather than whole process").
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This bug is causing random crashes
(http://bugzilla.kernel.org/show_bug.cgi?id=11414).

-fno-omit-frame-pointer is only needed on powerpc when -pg is also
supplied, and there is a gcc bug that causes incorrect code generation
on 32-bit powerpc when -fno-omit-frame-pointer is used---it uses stack
locations below the stack pointer, which is not allowed by the ABI
because those locations can and sometimes do get corrupted by an
interrupt.

This ensures that CONFIG_FRAME_POINTER is only selected by ftrace.
When CONFIG_FTRACE is enabled we also pass -mno-sched-epilog to work
around the gcc codegen bug.

Patch based on work by:
	Andreas Schwab <schwab@suse.de>
	Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This makes core_kernel_text() (and therefore kernel_text_address())
return the correct result.  Currently all the __devinit routines (at
least) will not be considered to be kernel text.

This is just a quick fix for 2.6.27 - hopefully we will be able to fix
this better in 2.6.28.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Commit bc033b63 ("powerpc/mm: Fix
attribute confusion with htab_bolt_mapping()") moved the check for
whether we should make pages of the linear mapping executable from
htab_bolt_mapping into its callers, including htab_initialize.
A side-effect of this is that the decision is now made once for
each contiguous section in the LMB array rather than for each page
individually.  This can often mean that the whole of the linear
mapping ends up being executable.

This reverts to the previous behaviour, where individual pages are
checked for being part of the kernel text or not, by moving the check
back down into htab_bolt_mapping.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes an uninitialised variable in the VSX alignment code.  It can
cause warnings from GCC (noticed with gcc-4.1.1).  Gcc is actually
correct in this instance, and this bug could cause the alignment
interrupt handler to send a SIGSEGV to the process on a legitimate
access.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Larry Finger reported at http://lkml.org/lkml/2008/9/1/90:
An ancient laptop of mine started throwing errors from b43legacy when
I started using 2.6.27 on it. This has been bisected to commit bfc0f594
"x86: merge tsc calibration".

The unification of the TSC code adopted mostly the 64bit code, which
prefers PMTIMER/HPET over the PIT calibration.

Larrys system has an AMD K6 CPU. Such systems are known to have
PMTIMER incarnations which run at double speed. This results in a
miscalibration of the TSC by factor 0.5. So the resulting calibrated
CPU/TSC speed is half of the real CPU speed, which means that the TSC
based delay loop will run half the time it should run. That might
explain why the b43legacy driver went berserk.

On the other hand we know about systems, where the PIT based
calibration results in random crap due to heavy SMI/SMM
disturbance. On those systems the PMTIMER/HPET based calibration logic
with SMI detection shows better results.

According to Alok also virtualized systems suffer from the PIT
calibration method.

The solution is to use a more wreckage aware aproach than the current
either/or decision.

1) reimplement the retry loop which was dropped from the 32bit code
during the merge. It repeats the calibration and selects the lowest
frequency value as this is probably the closest estimate to the real
frequency

2) Monitor the delta of the TSC values in the delay loop which waits
for the PIT counter to reach zero. If the maximum value is
significantly different from the minimum, then we have a pretty safe
indicator that the loop was disturbed by an SMI.

3) keep the pmtimer/hpet reference as a backup solution for systems
where the SMI disturbance is a permanent point of failure for PIT
based calibration

4) do the loop iteration for both methods, record the lowest value and
decide after all iterations finished.

5) Set a clear preference to PIT based calibration when the result
makes sense.

The implementation does the reference calibration based on
HPET/PMTIMER around the delay, which is necessary for the PIT anyway,
but keeps separate TSC values to ensure the "independency" of the
resulting calibration values.

Tested on various 32bit/64bit machines including Geode 266Mhz, AMD K6
(affected machine with a double speed pmtimer which I grabbed out of
the dump), Pentium class machines and AMD/Intel 64 bit boxen.
Bisected-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix operator precedence bug in atari_keyb_init, which caused a failure on CT60
Signed-off-by: NMichael Schmitz <schmitz@debian.org>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A parisc allmodconfig build produces this:

arch/parisc/hpux/fs.c:107: error: 'buffer' undeclared (first use in this function)

Introduced by commit da574983 ("[PATCH]
fix hpux_getdents()").

Helge Dille also reported this in bugzilla 11461:

	http://bugzilla.kernel.org/show_bug.cgi?id=11461

and he posted an identical patch.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Breaking lines due to some imaginary problem with a long line length is
often stupid and wrong, but never more so when it splits a string that
is printed out into multiple lines.  This really ended up making it much
harder to find where some error strings were printed out, because a
simple 'grep' didn't work.

I'm sure there is tons more of this particular idiocy hiding in other
places, but this particular case hit me once more last week. So fix it.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit a2bd7274.

It wasn't really right to begin with (there's a better fix for the
problem with e820 reservations clashing with PCI BAR's pending), but it
also actually causes more regressions, so it should be reverted even
before the better fix is finalized.

Rafael reports that this commit broke AHCI detection, and thus causes
the kernel to not boot on his quad core test box.
Reported-and-bisected-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: David Witbrodt <dawitbro@sbcglobal.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a device is under an EBUS or ISA bus, the resource flags
don't get set properly.

Fix this by re-evaluating the resource flags at each level of
bus as we apply ranges on the way to the root.  And let PCI
override any existing flags setting, but don't let the
default flags calculator make such overrides.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

remove unmatched comment end.
Signed-off-by: NJean-Christophe DUBOIS <jcd@tribudubois.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Using just 'unsigned' will make flags an unsigned int. While this is
arguably not an error on blackfin where sizeof(int) == sizeof(long),
the patch is still justified on the grounds of principle.

The patch was generated using the Coccinelle semantic patch framework.

Cc: Julia Lawall <julia@diku.dk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NVegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Reported by Stephen Rothwell.

Needed to fix the build when CONFIG_RELAY is enabled.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ordinarily, memory holes in flatmem still have a valid memmap and is safe
to use. However, an architecture (ARM) frees up the memmap backing memory
holes on the assumption it is never used. /proc/pagetypeinfo reads the
whole range of pages in a zone believing that the memmap is valid and that
pfn_valid will return false if it is not. On ARM, freeing the memmap breaks
the page->zone linkages even though pfn_valid() returns true and the kernel
can oops shortly afterwards due to accessing a bogus struct zone *.

This patch lets architectures say when FLATMEM can have holes in the
memmap. Rather than an expensive check for valid memory, /proc/pagetypeinfo
will confirm that the page linkages are still valid by checking page->zone
is still the expected zone. The lookup of page_zone is safe as there is a
limited range of memory that is accessed when calling page_zone.  Even if
page_zone happens to return the correct zone, the impact is that the counters
in /proc/pagetypeinfo are slightly off but fragmentation monitoring is
unlikely to be relevant on an embedded system.
Reported-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Tested-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch changes arm to use the new bcd2bin/bin2bcd functions instead
of the obsolete BCD_TO_BIN/BIN_TO_BCD macros.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Taken from omap 97b705ad835f1481270c4b67b402d6e37fa8ad15:
  ARM: OMAP: Misc compile fixes after syncing with mainline

  Also fix 2430 smc91x to use IRQ_LOWLEVEL.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Update omap_h2_1610 and omap_osk_5912 default configurations.

Add ams delta, n770, omap 2430sdp, apollon_2420, generic 1510, 1610,
1710, 2420, h4 2420, innovator 1510 and 1610, perseus2 730, palte,
palmtt, palmz71 and sx1 default configurations.

Pulled out of the omap zoom tree.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NVitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Enable some option commonly used by testers in defconfig, including
some very common device drivers and network boot support.  defconfig
is still not meant to be a kitchen-sink configuration.
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

AFAIR there exists blackfin hardware with PCI support, but the support
currently in the kernel fails to build starting with:

...
  CC      drivers/pci/probe.o
probe.c: In function 'pci_scan_slot':
probe.c:1056: error: implicit declaration of function 'pcibios_scan_all_fns'
make[3]: *** [drivers/pci/probe.o] Error 1
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NBryan Wu <cooloney@kernel.org>

Fix the S3C2443 clock register definitions for selecting the EPLL
reference clock described by S3C2443_CLKSRC_EPLLREF.
Signed-off-by: NWei Shuai <cpuwolf@gmail.com>
[ben-linux@fluff.org: minor description fixes]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The first spi bus is registered with number 0, but
the board data says that the device on it is registered
on bus 1.

Move the spi bus to bus 1 to keep the compatibility with the
original board-support patches.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move debugging output to dev_dbg() instead of dev_info().
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fix the following sparse warnings in arch/arm/plat-s3c24xx/pwm.c:

warning: symbol 's3c_device_timer' was not declared. Should it be static?
warning: symbol 'pwm_calc_tin' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fix the following sparse warnings in arch/arm/plat-s3c24xx/pwm-clock.c:

warning: symbol 'clk_timer_scaler' was not declared. Should it be static?
warning: symbol 'clk_timer_tclk' was not declared. Should it be static?
warning: symbol 'clk_timer_tdiv' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fix the following problems spotted by sparse:

warning: symbol 's3c24xx_gpiolib_input' was not declared. Should it be static?
warning: symbol 's3c24xx_gpiolib_output' was not declared. Should it be static?
warning: symbol 's3c24xx_gpiolib_set' was not declared. Should it be static?
warning: symbol 's3c24xx_gpiolib_get' was not declared. Should it be static?
warning: symbol 'gpios' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fix the following sparse errors in arch/arm/mach-s3c2410/nor-simtec.c:

53:27: warning: symbol 'simtec_nor_pdata' was not declared. Should it be static?
77:13: warning: symbol 'nor_simtec_init' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

corgi, spitz and poodle have audio codecs on their primary I2C bus so
need to call pxa_set_i2c_info() to set it up during init. Tested on
spitz by Stanislav.
Reported-by: NStanislav Brabec <utx@penguin.cz>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds the proper .gitignore file to ignore vmlinux.lds generated
in arch/mips/kernel/.
Signed-off-by: NFlorian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

kgdb_mips_notify is called on IBE/DBE/FPE/BP/TRAP/RI exception.  None
of them need fixup.  And doing fixup for a breakpoint exception will
confuse gdb.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use the register definitions of the MPMC controller from
mach-rc32434/rb.h instead of redefining them.
Signed-off-by: NFlorian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>