In the current design VFs were not allowed to program MAC/VLAN filters.
Only the PF driver was allowed to configure/provision MAC and transparent
VLANs to a VF. Change this to support MAC/VLAN filtering on a VF by a VM.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the VFs by default don't have the privilege to modify MAC address.
This will change in a subsequent fix wherein VFs will have the ability to
modify MAC/VLAN filters.

Fix be_mac_addr_set() logic to support MAC address modification on a
privileged VF too.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware workaround requesting hardware to skip vlan insertion is necessary
only when umc or qnq is enabled. Enabling this workaround in other scenarios
could cause controller to stall.
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be_find_vfs() is no longer needed as the common PCI calls provide the same
functionality.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to set the coherent DMA mask only if dma_set_mask() succeeded, and to
error out if either fails.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added code to initiate FW dump via ethtool. Driver checks if the previous dump
has been cleared before initiating the dump. It doesn't initiate the dump
if it is not cleared.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During a PCI EEH/AER error recovery flow, if the device did not successfully
restart, the error_detected() hook may be called a second time with a
"perm_failure" state. This patch skips over driver cleanup for the second
invocation of the callback.

Also, Lancer error recovery code is fixed-up to handle these changes.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW does not compute L4 checksum for IP Fragmented packets.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For padded packets, Lancer computes incorrect checksum. The workaround is
to trim such packets. This workaround is mainly for IPv4 packets.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Lancer, packets that are 32 bytes or less may cause a transmit stall.
The work-around is to pad such packets to a 36 byte length.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing the be_cmd_get_fw_ver() query from be_get_drvinfo() and invoking
the same from be_setup() and/or post firmware download.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor all TX HW workarounds into a separate routine called
be_xmit_workarounds().
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function be_get_nic_desc(), it will go through the descriptor array
returned from f/w. By comparing the desc_type field, it determines whether
there is a nic descriptor in the array or not. In the case of no nic
descriptor, this function should return NULL.

The code may return an invalide descriptor, when there is no nic descriptor
in the array and the desc_count is less than MAX_RESOURCE_DESC. In this case,
even there is no nic descriptor, it will still return the lase descriptor
since the i doesn't equal to MAX_RESOURCE_DESC.

This patch fix this issue by returning the descriptor when find it and return
NULL for other cases.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: NXiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to avoid double insertion of  vlan tags into the packet while
handling an asic workaroud (issue introduced by net next Commit bc0c3405)
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be_close() followed by be_clear() is called as a part of cleanup in the
EEH/AER flow.  This patch stops TX in be_close() before cleaning/freeing
up the TX queues in be_clear(). This prevents be_xmit() from being called
while TX queues no longer exist.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While cleaning RX queues, the CQ DB may be rung several times (with rearm)
while waiting for the flush compl. Each CQ-notify with rearm can result in
an event. The EQ may get full resulting in a HW error.

Fix this by not re-arming the CQ while notifying a valid completion.
Also, there's no need to wait for 1ms after destroying RXQ, as the code in
be_rx_cq_clean() waits for the flush compl to arrive.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The buffer size for a FW cmd request must be big enough to fit the response,
else the cmd fails. For GET_MAC_LIST cmd, though the memory allocated for
the cmd is big enough to fit the response, the payload_len value in the
WRB hdr is being set to the request length only.
Fix this for GET_MAC_LIST cmd.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the PF driver calls pci_enable_sriov(), the VFs may be probed
inline before the call returns. So, the resources required for all VFs
must be provisioned by the PF driver *before* calling pci_enable_sriov();
else, VF probe will fail.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As per SPEC, INTx mode is not supported on VFs. So if enable_msix fails,
then just fail probe. Also bail out of be_open if irq_register fails.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When RQ creation fails in be_open(), driver jumps to be_close() where
napi_disable() is done without a prior napi_enable(); leading to a hang.
This change is needed as there is no way to see if napi is enable/disabled.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increasing the timeout value of write_object command to 60 seconds as
30 second timeout was found to be not enough for the command to complete.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a user requests Promiscuous mode on SkyHawk-R devices,
the FW enables Desparate Promiscuous mode.
Due to this, we need to explicitly enable Multicast Promiscuous mode
so that Multicast packets are received as well.

This patch fixes that.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tx priority pause count is available with the driver.
But we were not showing it.
This change should fix it and display it in ethtool stats.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only BE devices provide 16-bit counter for rx_drops_no_fragment.
All other devices provide a 32-bit counter for this stat.
Use the 32-bit value where available.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SkyHawk-R devices should use v2 of cq_create command.
BE3/BE2 devices can use version 0 of the command to create a CQ.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lancer FW requires that the first cmd issued by the host-driver be an FLR.
So, re-order be_probe() to move be_cmd_function_reset() ahead of
be_cmd_fw_init().
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Skyhawk-R requires V1 version of GET_FUNCTION_CONFIG cmd to be used for
querrying resources available per function.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BE3 HW in UMC mode could wrongly double tag a packet with PVID
when the packet already has a inlined VLAN tag.
In UMC mode, When HW finds that a packet is already VLAN tagged
PVID should not be inserted into the packet.
To fix this use the FW hack to instruct the HW to skip PVID tagging.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ASIC could lockup in the transmit path when it tries
to insert VLAN in a specific ipv6 packet.
1) Identify the packet which can cause this.
2) Check if the firmware provides a workaround to prevent this.
3) If workaround is not present, drop the packet.
4) If the firmware provides a workaround, insert the VLAN tag in the
packet and inform the firmware to skip further VLAN insertions.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To work-around a HW bug that corrupts certain packets while inserting
a pvid, the driver needs to invoke a special hack in firmware to avoid
the VLAN tagging in the HW. Since this logic is missing from the driver,
removing the check for pvid.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sets the coherent DMA mask to 64-bit after the be2net driver has
been acknowledged that the system is 64-bit DMA capable. The coherent DMA
mask is examined by the Intel IOMMU driver to determine whether to allow
pass through context mapping for all devices. With this patch, the be2net
driver combined with be2net compatible hardware provides comparable
performance to the case where vt-d is disabled. The main use-case for this
change is to decrease the time necessary to copy virtual machine memory
during KVM live migration instantiations.

This patch was tested on a system that enables the IOMMU in non-coherent
mode. Two DMA remapper issues were encountered in the previous version and
both patches have been committed.
    commit ea2447f7
    commit 2e12bc29Signed-off-by: NCraig Hada <craig.hada@hp.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use GET_PROFILE_CONFIG_V1 cmd for BE3-R, to query the maximum number of
TX rings available per function. On SH-R the same is queried via the
GET_FUNCTION_CONFIG cmd.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid flashing BE3 UFI on BE3-R chip by verifying asic_revision
number of the chip.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't log "Out of MCCQ wrbs" msg. When the driver doesn't receive any
response from the FW it already logs a "FW not responding" message.
The driver runs out of MCCQ wrbs much later. Also, this message can
swamp the kernel log in HW/FW error scenarios.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>