This is needed for newer NICs.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This can lead to a panic if the driver isn't ready to
handle them. Since our interrupt line is shared, we can get
an interrupt at any time (and CONFIG_DEBUG_SHIRQ checks
that even when the interrupt is being freed).

If the op_mode has gone away, we musn't call it. To avoid
this the transport disables the interrupts when the hw is
stopped and the op_mode is leaving.
If there is an event that would cause an interrupt the INTA
register is updated regardless of the enablement of the
interrupts: even if the interrupts are disabled, the INTA
will be changed, but the device won't issue an interrupt.
But the ISR can be called at any time, so we ought ignore
the value in the INTA otherwise we can call the op_mode
after it was freed.

I found this bug when the op_mode_start failed, and called
iwl_trans_stop_hw(trans, true). Then I played with the
RFKILL button, and removed the module.
While removing the module, the IRQ is freed, and the ISR is
called (CONFIG_DEBUG_SHIRQ enabled). Panic.

Cc: stable@vger.kernel.org
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We know that we have issues with the fw in the reclaim path.
This is why iwl_reclaim doesn't complain too loud when it
happens since it is recoverable. Somehow, the caller of
iwl_reclaim however WARNed when it happens. This doesn't
make any sense.

When I digged into the history of that code, I discovered
that this bug occurs only when we receive a BA notification.
So move the W/A in the BA notification handling code where
it was before.

This patch addresses:
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2387

Cc: stable@vger.kernel.org
Reported-by: NFlorian Reitmeir <florian@reitmeir.org>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The WARN_ON_ONCE() check for scan_request will not correctly detect
a NULL pointer for scan_type == IWL_SCAN_NORMAL. Make it explicit
that the check only applies to normal scans.

Convert WARN_ON_ONCE to WARN_ON since priv->scan_request really _can't_
be NULL for normal scans. If it is then we should emit frequent warnings.

This smatch warning led to scrutiny of iwlagn_request_scan():

drivers/net/wireless/iwlwifi/dvm/scan.c:894 iwlagn_request_scan() error: we previously assumed 'priv->scan_request' could be null (see line 792)
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use the standard #defines rather than creating local definitions for
PCIe Capability ASPM fields.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NJohannes Berg <johannes.berg@intel.com>

iwl_pciexp_link_ctrl() has only one call site and no longer provides any
useful abstraction, so collapse it into the caller.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NJohannes Berg <johannes.berg@intel.com>

By using a few temporary variables, smatch can track
what's happening and stops complaining that we access
beyond the tid_data array.

This also makes the generated code a bit smaller, so
it's a win all around.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since the device is taken down in stop_hw, call reset_ict
from there too.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

New transports may handle it internally for better performance.
Also move the tracing inside PRPH access which will make the
output more readable:

iwlwifi_dev_ioread_prph32: Read 0x0 from SCD_AGGR_SEL (32-bit)

instead of the corresponding accesses to HBUS_TARG_PRPH_*.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since we will have several forms of NVM (EEPROM, OTP, etc.)
and they will have different layouts, make the parsed data
more generic. This allows functional code to be independent
of a specific layout.

Also change some variables and function names from having
"eeprom" to "nvm" in their name.
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't return a hard coded -EFAULT, but rather the error
that occurred in the flow.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since the op_mode is leaving, the transport should set
its pointer to it to NULL to not point to freed memory.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The FH (DMA engine) tells the driver the index of the last
ready (closed) Rx buffer. This data is in closed_rb_num.
If we read this data several times we may get inconsistencies
between the code and the debug prints which can make it
harder to debug issues here.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The vendor radiotap patch added a few fields to
struct ieee80211_rx_status that need to be zero,
initialize the struct instead of using whatever
was left on the stack.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Tested-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.

Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Fix a copy paste error in iwl_calc_basic_rates which leads
to a wrong calculation of CCK basic rates.

Cc: stable@vger.kernel.org
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers (e.g. wl12xx) might need to know the vif
to roc on (mainly in order to configure the
rx filters correctly).

Add the vif to the op params, and update the current
users (iwlwifi) to use the new api.
Signed-off-by: NEliad Peller <eliad@wizery.com>
[fix hwsim]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

iwl-trans.h was included twice.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will allow to reduce slightly the number of interrupts
without sacrificing too much the latency in the Rx path.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It is not used outside pcie/rx.c.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Really trivial clean up.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Also, prefer the if(!X) notation over if(X == 0).
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When software crypto is enabled, it isn't safe
to enable MFP since the firmware interprets some
management packets, and with MFP it would do so
without proper validation.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

One one just a wrapper of the second, squash them.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Rename static functions. Function moved from trans.c to
tx.c. A few could be made static, others had to be exported.

Functions that implement the transport API are prefixed by
iwl_trans_pcie_, the others by iwl_pcie_.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Functions that implement the transport API are prefixed by
iwl_trans_pcie_, the others by iwl_pcie_.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Rename static functions. Function moved from trans.c to
rx.c. A few could be made static, others had to be exported.
Also, don't use rxb or rxbuf, but rb which stands for receive
buffer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is its natural place
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

1) s/tx_queue/txq
	for the sake of consistency.

2) s/rx_queue/rxq
	for the sake of consistency.

3) Make all functions begin with iwl_pcie_
	iwl_queue_init and iwl_queue_space are an exception
	since they are not PCIE specific although they are in
	pcie subdir.

4) s/trans_pcie_get_cmd_string/get_cmd_string
	it is much shorter and used in debug prints which
	are long lines.

5) s/iwl_bg_rx_replenish/iwl_pcie_rx_replenish_work
	this better emphasizes that it is a work

6) remove invalid kernelDOC markers

pcie/tx.c and pcie/trans.c still needs to be cleaned up.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This can happen when we shut down suddenly an interface.

Cc: stable@vger.kernel.org
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the firmware is in SNIFFER mode, it leaves
the FCS at the end of frame. Not telling mac80211
means it won't add the right flag to the radiotap
header and that confuses wireshark.

Since mac80211 doesn't have a per-packet flag, set
the HW flag dynamically. This works as the monitor
vif can only be present in the driver by itself.

This fixes a regression introduced by my

commit 57897726
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Fri May 11 10:53:18 2012 +0200

    iwlwifi: support explicit monitor interface

Cc: stable@vger.kernel.org [3.5+]
Reported-by: NMARK PHILLIPS <mark.phillips@virgin.net>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is not needed, the comment there was wrong, it
is only needed when MSI was *not* enabled.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The allocation failure will already be very verbose.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a firmware error occurs, don't just abort synchronous
commands but also return an error (-EIO) and block any new
commands as well. Currently, an error is only returned if
WANT_SKB was set which is confusing and can lead to issues.

Blocking is done until a new firmware image is loaded.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The printk message should say RX, not TX.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>