Remove CONFIG_USE_GENERIC_SMP_HELPERS left by commit 0a06ff06
("kernel: remove CONFIG_USE_GENERIC_SMP_HELPERS").
Signed-off-by: NYuanhan Liu <yuanhan.liu@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

High-availability Seamless Redundancy ("HSR") provides instant failover
redundancy for Ethernet networks. It requires a special network topology where
all nodes are connected in a ring (each node having two physical network
interfaces). It is suited for applications that demand high availability and
very short reaction time.

HSR acts on the Ethernet layer, using a registered Ethernet protocol type to
send special HSR frames in both directions over the ring. The driver creates
virtual network interfaces that can be used just like any ordinary Linux
network interface, for IP/TCP/UDP traffic etc. All nodes in the network ring
must be HSR capable.

This code is a "best effort" to comply with the HSR standard as described in
IEC 62439-3:2010 (HSRv0).
Signed-off-by: NArvid Brodin <arvid.brodin@xdin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Eliezer renames several *ll_poll to *busy_poll, but forgets
CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too.

Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike for IPv6, the IPv4 checksum functions are only available
if CONFIG_INET is set.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove NET_LL_RX_POLL from the config menu.
Change default to y.
Busy polling still needs to be enabled at run time.
Signed-off-by: NEliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use sched_clock() instead of get_cycles().
We can use sched_clock() because we don't care much about accuracy.
Remove the dependency on X86_TSC
Signed-off-by: NEliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds an ndo_ll_poll method and the code that supports it.
This method can be used by low latency applications to busy-poll
Ethernet device queues directly from the socket code.
sysctl_net_ll_poll controls how many microseconds to poll.
Default is zero (disabled).
Individual protocol support will be added by subsequent patches.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NEliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Tested-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we have at least one user of this function outside of CONFIG_NET
scope, we have to provide this function independently. The proposed
solution is to move it under lib/net_utils.c with corresponding
configuration variable and select wherever it is needed.
Signed-off-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Reported-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the case where a non-MPLS packet is received and an MPLS stack is
added it may well be the case that the original skb is GSO but the
NIC used for transmit does not support GSO of MPLS packets.

The aim of this code is to provide GSO in software for MPLS packets
whose skbs are GSO.

SKB Usage:

When an implementation adds an MPLS stack to a non-MPLS packet it should do
the following to skb metadata:

* Set skb->inner_protocol to the old non-MPLS ethertype of the packet.
  skb->inner_protocol is added by this patch.

* Set skb->protocol to the new MPLS ethertype of the packet.

* Set skb->network_header to correspond to the
  end of the L3 header, including the MPLS label stack.

I have posted a patch, "[PATCH v3.29] datapath: Add basic MPLS support to
kernel" which adds MPLS support to the kernel datapath of Open vSwtich.
That patch sets the above requirements in datapath/actions.c:push_mpls()
and was used to exercise this code.  The datapath patch is against the Open
vSwtich tree but it is intended that it be added to the Open vSwtich code
present in the mainline Linux kernel at some point.

Features:

I believe that the approach that I have taken is at least partially
consistent with the handling of other protocols.  Jesse, I understand that
you have some ideas here.  I am more than happy to change my implementation.

This patch adds dev->mpls_features which may be used by devices
to advertise features supported for MPLS packets.

A new NETIF_F_MPLS_GSO feature is added for devices which support
hardware MPLS GSO offload.  Currently no devices support this
and MPLS GSO always falls back to software.

Alternate Implementation:

One possible alternate implementation is to teach netif_skb_features()
and skb_network_protocol() about MPLS, in a similar way to their
understanding of VLANs. I believe this would avoid the need
for net/mpls/mpls_gso.c and in particular the calls to
__skb_push() and __skb_push() in mpls_gso_segment().

I have decided on the implementation in this patch as it should
not introduce any overhead in the case where mpls_gso is not compiled
into the kernel or inserted as a module.

MPLS GSO suggested by Jesse Gross.
Based in part on "v4 GRE: Add TCP segmentation offload for GRE"
by Pravin B Shelar.

Cc: Jesse Gross <jesse@nicira.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A cpu executing the network receive path sheds packets when its input
queue grows to netdev_max_backlog. A single high rate flow (such as a
spoofed source DoS) can exceed a single cpu processing rate and will
degrade throughput of other flows hashed onto the same cpu.

This patch adds a more fine grained hashtable. If the netdev backlog
is above a threshold, IRQ cpus track the ratio of total traffic of
each flow (using 4096 buckets, configurable). The ratio is measured
by counting the number of packets per flow over the last 256 packets
from the source cpu. Any flow that occupies a large fraction of this
(set at 50%) will see packet drop while above the threshold.

Tested:
Setup is a muli-threaded UDP echo server with network rx IRQ on cpu0,
kernel receive (RPS) on cpu0 and application threads on cpus 2--7
each handling 20k req/s. Throughput halves when hit with a 400 kpps
antagonist storm. With this patch applied, antagonist overload is
dropped and the server processes its complete load.

The patch is effective when kernel receive processing is the
bottleneck. The above RPS scenario is a extreme, but the same is
reached with RFS and sufficient kernel processing (iptables, packet
socket tap, ..).
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, in menuconfig, Netlink's new mmaped IO is the very first
entry under the ``Networking support'' item and comes even before
``Networking options'':

  [ ]   Netlink: mmaped IO
  Networking options  --->
  ...

Lets move this into ``Networking options'' under netlink's Kconfig,
since this might be more appropriate. Introduced by commit ccdfcc39
(``netlink: mmaped netlink: ring setup'').
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for mmap'ed RX and TX ring setup and teardown based on the
af_packet.c code. The following patches will use this to add the real
mmap'ed receive and transmit functionality.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netlink_diag can be built as a module, just like it's done in
unix sockets.

The core dumping message carries the basic info about netlink sockets:
family, type and protocol, portis, dst_group, dst_portid, state.

Groups can be received as an optional parameter NETLINK_DIAG_GROUPS.

Netlink sockets cab be filtered by protocols.

The socket inode number and cookie is reserved for future per-socket info
retrieving. The per-protocol filtering is also reserved for future by
requiring the sdiag_protocol to be zero.

The file /proc/net/netlink doesn't provide enough information for
dumping netlink sockets. It doesn't provide dst_group, dst_portid,
groups above 32.

v2: fix NETLINK_DIAG_MAX. Now it's equal to the last constant.
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: NAndrey Vagin <avagin@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VM Sockets allows communication between virtual machines and the hypervisor.
User level applications both in a virtual machine and on the host can use the
VM Sockets API, which facilitates fast and efficient communication between
guest virtual machines and their host.  A socket address family, designed to be
compatible with UDP and TCP at the interface level, is provided.

Today, VM Sockets is used by various VMware Tools components inside the guest
for zero-config, network-less access to VMware host services.  In addition to
this, VMware's users are using VM Sockets for various applications, where
network access of the virtual machine is restricted or non-existent.  Examples
of this are VMs communicating with device proxies for proprietary hardware
running as host applications and automated testing of applications running
within virtual machines.

The VMware VM Sockets are similar to other socket types, like Berkeley UNIX
socket interface.  The VM Sockets module supports both connection-oriented
stream sockets like TCP, and connectionless datagram sockets like UDP. The VM
Sockets protocol family is defined as "AF_VSOCK" and the socket operations
split for SOCK_DGRAM and SOCK_STREAM.

For additional information about the use of VM Sockets, please refer to the
VM Sockets Programming Guide available at:

https://www.vmware.com/support/developer/vmci-sdk/Signed-off-by: NGeorge Zhang <georgezhang@vmware.com>
Signed-off-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NAndy king <acking@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original suggestion to delete wanrouter started earlier
with the mainline commit f0d1b3c2
("net/wanrouter: Deprecate and schedule for removal") in May 2012.

More importantly, Dan Carpenter found[1] that the driver had a
fundamental breakage introduced back in 2008, with commit
7be6065b ("netdevice wanrouter: Convert directly reference of
netdev->priv").  So we know with certainty that the code hasn't been
used by anyone willing to at least take the effort to send an e-mail
report of breakage for at least 4 years.

This commit does a decouple of the wanrouter subsystem, by going
after the Makefile/Kconfig and similar files, so that these mainline
files that we are keeping do not have the big wanrouter file/driver
deletion commit tied into their history.

Once this commit is in place, we then can remove the obsolete cyclomx
drivers and similar that have a dependency on CONFIG_WAN_ROUTER_DRIVERS.

[1] http://www.spinics.net/lists/netdev/msg218670.htmlOriginally-by: NJoe Perches <joe@perches.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.

CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NKees Cook <keescook@chromium.org>
Acked-by: NDavid S. Miller <davem@davemloft.net>

This patch makes it so that we can support transmit packet steering without
sysfs needing to be enabled.  The reason for making this change is to make
it so that a driver can make use of the XPS even while the sysfs portion of
the interface is not present.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stephen Rothwell says:

====================
After merging the final tree, today's linux-next build (powerpc
ppc44x_defconfig) failed like this:

net/built-in.o: In function `tcp_fastopen_ctx_free':
tcp_fastopen.c:(.text+0x5cc5c): undefined reference to `crypto_destroy_tfm'
net/built-in.o: In function `tcp_fastopen_reset_cipher':
(.text+0x5cccc): undefined reference to `crypto_alloc_base'
net/built-in.o: In function `tcp_fastopen_reset_cipher':
(.text+0x5cd6c): undefined reference to `crypto_destroy_tfm'

Presumably caused by commit 10467163 ("tcp: TCP Fast Open Server -
header & support functions") from the net-next tree.  I assume that some
dependency on the CRYPTO infrastructure is missing.

I have reverted commit 1bed966c ("Merge branch
'tcp_fastopen_server'") for today.
====================
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no point having the NET dependency on the select target, as it
forces all users to depend on NET to tell they support BPF_JIT.  Move
the config option to the bottom of the file - this could be a nice place
also for future "selectable" config symbols.

Fix up all users to drop the dependency on NET now that it is not
required to supress warnings for non-NET builds.
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Acked-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

More spring cleaning!

The ancient Econet protocol should go. Most of the bug fixes in recent
years have been fixing security vulnerabilities. The hardware hasn't
been made since the 90s, it is only interesting as an archeological curiosity.

For the truly curious, or insomniac, go read up on it.
  http://en.wikipedia.org/wiki/EconetSigned-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When I first wrote drop monitor I wrote it to just build monolithically.  There
is no reason it can't be built modularly as well, so lets give it that
flexibiity.

I've tested this by building it as both a module and monolithically, and it
seems to work quite well

Change notes:

v2)
* fixed for_each_present_cpu loops to be more correct as per Eric D.
* Converted exit path failures to BUG_ON as per Ben H.

v3)
* Converted del_timer to del_timer_sync to close race noted by Ben H.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An interface to allocate and register ieee802154 compatible device.
The allocated device has the following representation in memory:

	+-----------------------+
	| struct wpan_phy       |
	+-----------------------+
	| struct mac802154_priv |
	+-----------------------+
	| driver's private data |
	+-----------------------+

Used by device drivers to register new instance in the stack.
Signed-off-by: NAlexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Open vSwitch is a multilayer Ethernet switch targeted at virtualized
environments.  In addition to supporting a variety of features
expected in a traditional hardware switch, it enables fine-grained
programmatic extension and flow-based control of the network.
This control is useful in a wide variety of applications but is
particularly important in multi-server virtualization deployments,
which are often characterized by highly dynamic endpoints and the need
to maintain logical abstractions for multiple tenants.

The Open vSwitch datapath provides an in-kernel fast path for packet
forwarding.  It is complemented by a userspace daemon, ovs-vswitchd,
which is able to accept configuration from a variety of sources and
translate it into packet processing rules.

See http://openvswitch.org for more information and userspace
utilities.
Signed-off-by: NJesse Gross <jesse@nicira.com>

Networking stack support for byte queue limits, uses dynamic queue
limits library.  Byte queue limits are maintained per transmit queue,
and a dql structure has been added to netdev_queue structure for this
purpose.

Configuration of bql is in the tx-<n> sysfs directory for the queue
under the byte_queue_limits directory.  Configuration includes:
limit_min, bql minimum limit
limit_max, bql maximum limit
hold_time, bql slack hold time

Also under the directory are:
limit, current byte limit
inflight, current number of bytes on the queue
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds in the infrastructure code to create the network priority
cgroup.  The cgroup, in addition to the standard processes file creates two
control files:

1) prioidx - This is a read-only file that exports the index of this cgroup.
This is a value that is both arbitrary and unique to a cgroup in this subsystem,
and is used to index the per-device priority map

2) priomap - This is a writeable file.  On read it reports a table of 2-tuples
<name:priority> where name is the name of a network interface and priority is
indicates the priority assigned to frames egresessing on the named interface and
originating from a pid in this cgroup

This cgroup allows for skb priority to be set prior to a root qdisc getting
selected. This is benenficial for DCB enabled systems, in that it allows for any
application to use dcb configured priorities so without application modification
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
CC: Robert Love <robert.w.love@intel.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NFC subsystem core is responsible for providing the device driver
interface. It is also responsible for providing an interface to the control
operations and data exchange.
Signed-off-by: NLauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: NAloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

module_alloc() and module_free() are available only if CONFIG_MODULES=y
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to speedup packet filtering, here is an implementation of a
JIT compiler for x86_64

It is disabled by default, and must be enabled by the admin.

echo 1 >/proc/sys/net/core/bpf_jit_enable

It uses module_alloc() and module_free() to get memory in the 2GB text
kernel range since we call helpers functions from the generated code.

EAX : BPF A accumulator
EBX : BPF X accumulator
RDI : pointer to skb   (first argument given to JIT function)
RBP : frame pointer (even if CONFIG_FRAME_POINTER=n)
r9d : skb->len - skb->data_len (headlen)
r8  : skb->data

To get a trace of generated code, use :

echo 2 >/proc/sys/net/core/bpf_jit_enable

Example of generated code :

# tcpdump -p -n -s 0 -i eth1 host 192.168.20.0/24

flen=18 proglen=147 pass=3 image=ffffffffa00b5000
JIT code: ffffffffa00b5000: 55 48 89 e5 48 83 ec 60 48 89 5d f8 44 8b 4f 60
JIT code: ffffffffa00b5010: 44 2b 4f 64 4c 8b 87 b8 00 00 00 be 0c 00 00 00
JIT code: ffffffffa00b5020: e8 24 7b f7 e0 3d 00 08 00 00 75 28 be 1a 00 00
JIT code: ffffffffa00b5030: 00 e8 fe 7a f7 e0 24 00 3d 00 14 a8 c0 74 49 be
JIT code: ffffffffa00b5040: 1e 00 00 00 e8 eb 7a f7 e0 24 00 3d 00 14 a8 c0
JIT code: ffffffffa00b5050: 74 36 eb 3b 3d 06 08 00 00 74 07 3d 35 80 00 00
JIT code: ffffffffa00b5060: 75 2d be 1c 00 00 00 e8 c8 7a f7 e0 24 00 3d 00
JIT code: ffffffffa00b5070: 14 a8 c0 74 13 be 26 00 00 00 e8 b5 7a f7 e0 24
JIT code: ffffffffa00b5080: 00 3d 00 14 a8 c0 75 07 b8 ff ff 00 00 eb 02 31
JIT code: ffffffffa00b5090: c0 c9 c3

BPF program is 144 bytes long, so native program is almost same size ;)

(000) ldh      [12]
(001) jeq      #0x800           jt 2    jf 8
(002) ld       [26]
(003) and      #0xffffff00
(004) jeq      #0xc0a81400      jt 16   jf 5
(005) ld       [30]
(006) and      #0xffffff00
(007) jeq      #0xc0a81400      jt 16   jf 17
(008) jeq      #0x806           jt 10   jf 9
(009) jeq      #0x8035          jt 10   jf 17
(010) ld       [28]
(011) and      #0xffffff00
(012) jeq      #0xc0a81400      jt 16   jf 13
(013) ld       [38]
(014) and      #0xffffff00
(015) jeq      #0xc0a81400      jt 16   jf 17
(016) ret      #65535
(017) ret      #0
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit a6238f21

Appletalk got some patches to fix up the BLK usage in it in the
network tree, so this removal isn't needed.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <acme@ghostprotocols.net>
Cc: netdev@vger.kernel.org,
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For all I know, Appletalk is dead, the only reasonable
use right now would be nostalgia, and that can be served
well enough by old kernels. The code is largely not
in a bad shape, but it still uses the big kernel lock,
and nobody seems motivated to change that.

FWIW, the last release of MacOS that supported Appletalk
was MacOS X 10.5, made in 2007, and it has been abandoned
by Apple with 10.6. Using TCP/IP instead of Appletalk has
been supported since MacOS 7.6, which was released in
1997 and is able to run on most of the legacy hardware.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allow drivers for multiqueue hardware with flow filter tables to
accelerate RFS.  The driver must:

1. Set net_device::rx_cpu_rmap to a cpu_rmap of the RX completion
IRQs (in queue order).  This will provide a mapping from CPUs to the
queues for which completions are handled nearest to them.

2. Implement net_device_ops::ndo_rx_flow_steer.  This operation adds
or replaces a filter steering the given flow to the given RX queue, if
possible.

3. Periodically remove filters for which rps_may_expire_flow() returns
true.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

B.A.T.M.A.N. (better approach to mobile ad-hoc networking) is a routing
protocol for multi-hop ad-hoc mesh networks. The networks may be wired or
wireless. See http://www.open-mesh.org/ for more information and user space
tools.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds XPS_CONFIG option to enable and disable XPS.  This is
done in the same manner as RPS_CONFIG.  This is also fixes build
failure in XPS code when SMP is not enabled.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the documentation refers to web pages under
the domain `osdl.org'. However, `osdl.org' now
redirects to `linuxfoundation.org'.

Rather than rely on redirections, this patch updates
the addresses appropriately; for the most part, only
documentation that is meant to be current has been
updated.

The patch should be pretty quick to scan and check;
each new web-page url was gotten by trying out the
original URL in a browser and then simply copying the
the redirected URL (formatting as necessary).

There is some conflict as to which one of these domain
names is preferred:

  linuxfoundation.org
  linux-foundation.org

So, I wrote:

  info@linuxfoundation.org

and got this reply:

  Message-ID: <4CE17EE6.9040807@linuxfoundation.org>
  Date: Mon, 15 Nov 2010 10:41:42 -0800
  From: David Ames <david@linuxfoundation.org>

  ...

  linuxfoundation.org is preferred. The canonical name for our web site is
  www.linuxfoundation.org. Our list site is actually
  lists.linux-foundation.org.

  Regarding email linuxfoundation.org is preferred there are a few people
  who choose to use linux-foundation.org for their own reasons.

Consequently, I used `linuxfoundation.org' for web pages and
`lists.linux-foundation.org' for mailing-list web pages and email addresses;
the only personal email address I updated from `@osdl.org' was that of
Andrew Morton, who prefers `linux-foundation.org' according `git log'.
Signed-off-by: NMichael Witten <mfwitten@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This factors out protocol and low-level storage parts of ceph into a
separate libceph module living in net/ceph and include/linux/ceph.  This
is mostly a matter of moving files around.  However, a few key pieces
of the interface change as well:

 - ceph_client becomes ceph_fs_client and ceph_client, where the latter
   captures the mon and osd clients, and the fs_client gets the mds client
   and file system specific pieces.
 - Mount option parsing and debugfs setup is correspondingly broken into
   two pieces.
 - The mon client gets a generic handler callback for otherwise unknown
   messages (mds map, in this case).
 - The basic supported/required feature bits can be expanded (and are by
   ceph_fs_client).

No functional change, aside from some subtle error handling cases that got
cleaned up in the refactoring process.
Signed-off-by: NSage Weil <sage@newdream.net>

You cannot invoke __smp_call_function_single() unless the
architecture sets this symbol.
Reported-by: NDaniel Hellstrom <daniel@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate out the DNS resolver key type from the CIFS filesystem into its own
module so that it can be made available for general use, including the AFS
filesystem module.

This facility makes it possible for the kernel to upcall to userspace to have
it issue DNS requests, package up the replies and present them to the kernel
in a useful form.  The kernel is then able to cache the DNS replies as keys
can be retained in keyrings.

Resolver keys are of type "dns_resolver" and have a case-insensitive
description that is of the form "[<type>:]<domain_name>".  The optional <type>
indicates the particular DNS lookup and packaging that's required.  The
<domain_name> is the query to be made.

If <type> isn't given, a basic hostname to IP address lookup is made, and the
result is stored in the key in the form of a printable string consisting of a
comma-separated list of IPv4 and IPv6 addresses.

This key type is supported by userspace helpers driven from /sbin/request-key
and configured through /etc/request-key.conf.  The cifs.upcall utility is
invoked for UNC path server name to IP address resolution.

The CIFS functionality is encapsulated by the dns_resolve_unc_to_ip() function,
which is used to resolve a UNC path to an IP address for CIFS filesystem.  This
part remains in the CIFS module for now.

See the added Documentation/networking/dns_resolver.txt for more information.
Signed-off-by: NWang Lei <wang840925@gmail.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NSteve French <sfrench@us.ibm.com>

WIRELESS_EXT is not the correct dependency.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new networking option to allow hardware time stamps
from PHY devices. When enabled, likely candidates among incoming and
outgoing network packets are offered to the PHY driver for possible
time stamping. When accepted by the PHY driver, incoming packets are
deferred for later delivery by the driver.

The patch also adds phylib driver methods for the SIOCSHWTSTAMP ioctl
and callbacks for transmit and receive time stamping. Drivers may
optionally implement these functions.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>