ia64:

drivers/net/wireless/iwlwifi/iwl-led.c: In function `iwl_get_blink_rate':
drivers/net/wireless/iwlwifi/iwl-led.c:271: warning: long long int format, s64 arg (arg 6)
drivers/net/wireless/iwlwifi/iwl-led.c:271: warning: long long int format, u64 arg (arg 7)

We do not know what type the architecture uses to impement u64 and s64,
hence we must cast the variables for printing.

Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Return the proper error code rather than a hard-coded ENOMEM from
ieee80211_wep_init.  Also, print the error code on failure.
Signed-off-by: NJeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use dev_kfree_skb_any(); instead of dev_kfree_skb();, since
ieee80211_beacon_get function might be called from atomic.
(It's in a fail path.)
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the queues are being initialized the entry flags fields must be
reset to 0. When this does not happen some entries might still be
marked as "occupied" after an ifdown & ifup cycle which would trigger
errors when the entry is being accessed:

	phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
	Please file bug report to http://rt2x00.serialmonkey.com.

This also fixes the mac80211 warning:

	------------[ cut here ]------------
	WARNING: at net/mac80211/tx.c:1238 ieee80211_master_start_xmit+0x30a/0x350 [mac80211]()

which was triggered by the queue error.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00 will only perform configuration changes from
mac80211 when the configuration option has changed.
This means it keeps track of the current active configuration
and will check these values when the config() callback function
is used.

However this causes breakage when the interface has been
brought down and up again, since all stored active values
aren't reset while the registers might have.
This is for example the case with rt61pci antenna registers which
will jump to invalid values when the interface has been started.

To make sure a full configuration takes place after the start()
callback function, a new flag is added which will be checked
during config() and skips the "what's changed" phase.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.

The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression l;
@@

mutex_lock(l);
... when != mutex_unlock(l)
    when any
    when strict
(
if (...) { ... when != mutex_unlock(l)
+   mutex_unlock(l);
    return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.

The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression l;
@@

mutex_lock(l);
... when != mutex_unlock(l)
    when any
    when strict
(
if (...) { ... when != mutex_unlock(l)
+   mutex_unlock(l);
    return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When sending the RTS/CTS frame fails, we should
free the skb buffer which was created.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When IEEE80211_TX_CTL_ASSIGN_SEQ is not set,
the driver should disable hardware sequence counting
to make sure the mac80211 provided counter is used.
This fixes QOS sequence counting, since that is one
of the cases where mac80211 provides a seperate
sequence counter.

By moving the sequence counting code to rt2x00queue
we make sure that _all_ frames get the sequence counter,
including RTS/CTS and Beacon frames.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When setting up a beacon template, the length of the beacon is
calculated with the assumption that the SKB already contains
the Tx descriptor. In the case of beacons it doesn't.

This patch undoes the damage by adding the Tx descriptor length
to the beacon length. This is safe, because the shortest possible
beacon is longer than the Tx header.
Signed-off-by: NIwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Switches rt73usb to use large vendor requests for firmware
and beacons. This also fixes the garbled beacon bug.
Signed-off-by: NIwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adds an extra rt2x00 vendor request function to support register
transfers beyond the CSR_CACHE_SIZE / USB packet size limit. This
is useful for firmware uploads, beacon templates and keys, all
of which are to large to do with a single USB request.
Signed-off-by: NIwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Olivier reported a difference between the EIFS
values used in the legacy driver and the one in
the rt2x00 drivers.

In rt2x00 the value was
	( SIFS + (8 * (IEEE80211_HEADER + ACK_SIZE)) )
which comes down to 314us while the legacy driver uses the value 364us

This was caused because EIFS is: SIFS + DIFS + AckTime
This patch will fix this by adding the DIFS by the above value,
and creating a SHORT_EIFS define which uses the SHORT_DIFS.
Reported-by: NOlivier Cornu <o.cornu@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00queue_free_skb() was declared twice.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

MSI is a nice thing, but we cannot enable it without changing the
interrupt handler.  If we do it, we break MSI capable hardware,
specifically AR5006 chipset.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k_beacon_update takes sc->lock upon entry.  However, it is only
called from within ath5k_config_interface, which already holds the lock.
Remove the unnecessary locking from ath5k_beacon_update.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CC [M]  drivers/net/wireless/iwlwifi/iwl-scan.o
drivers/net/wireless/iwlwifi/iwl-scan.c: In function 'iwl_rx_scan_complete_notif':
drivers/net/wireless/iwlwifi/iwl-scan.c:274: warning: unused variable 'scan_notif'
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Acked-by: NTomas Winkler <tomasw@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CC [M]  drivers/net/wireless/iwlwifi/iwl-rfkill.o
drivers/net/wireless/iwlwifi/iwl-led.c: In function 'iwl_led_brightness_set':
drivers/net/wireless/iwlwifi/iwl-led.c:198: error: 'led_type_str' undeclared (first use in this function)
drivers/net/wireless/iwlwifi/iwl-led.c:198: error: (Each undeclared identifier is reported only once
drivers/net/wireless/iwlwifi/iwl-led.c:198: error: for each function it appears in.)

The problem is that led_type_str is defined under CONFIG_IWLWIFI_DEBUG
while IWL_DEBUG is a static inline function in this case. Replace it
with macro.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some persistent settings were using hex and others decimal.  In some cases,
values were set in hex but reported in decimal.  Confusing.
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When building the wireless-next-2.6 tree with CONFIG_IWL3945 (for building
iwl-3945 driver) and where CONFIG_IWL3945_LEDS is not set,
we get this warning:
drivers/net/wireless/iwlwifi/iwl-3945.c: In function
'iwl3945_pass_packet_to_mac80211':
drivers/net/wireless/iwlwifi/iwl-3945.c:633: warning: unused variable 'hdr'

This patch adds #ifdef to iwl3945_pass_packet_to_mac80211() to avoid this
warning. (The variable 'hdr' is used only if CONFIG_IWL3945_LEDS is set)
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For some stupid reason, I sent and old version of the patch minor kernel
doc-fix patch, and it got merged before I noticed the problem. This is an
incremental fix on top.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are two mutexes in rfkill:

rfkill->mutex, which protects some of the fields of a rfkill struct, and is
also used for callback serialization.

rfkill_mutex, which protects the global state, the list of registered
rfkill structs and rfkill->claim.

Make sure to use the correct mutex, and to not miss locking rfkill->mutex
even when we already took rfkill_mutex.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reorder fields in struct rfkill and add comments to make it clear
which fields are protected by rfkill->mutex.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rfkill needs to unregister the led trigger AFTER a call to
rfkill_remove_switch(), otherwise it will not update the LED state,
possibly leaving it ON when it should be OFF.

To make led-trigger unregistering safer, guard against unregistering a
trigger twice, and also against issuing trigger events to a led trigger
that was unregistered.  This makes the error unwind paths more resilient.

Refer to "rfkill: Register LED triggers before registering switch".
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While the rfkill class does work with just get_state(), it doesn't work
well on devices that are subject to external events that cause rfkill state
changes.

Document that rfkill_force_state() is required in those cases.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Helge Deller reports that HP laptops (NC4010 and NC6000) use active-
high signals to turn on the LEDs.  Previous code used active-low for
all devices.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

- free and re-request irq since it might have changed during suspend
- disable and enable msi
- don't set D0 state of the device, it's already done by the PCI layer
- do restore_state before enable_device, it's safer
- check ath5k_init return value
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't sync
- coherent mapping (descriptors)
- before unmap, it's useless
- (wrongly anyway -- for_cpu) beacon skb, it's just mapped,
  so by the device yet
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make sure that the irq is not in progress after stop. This means
two things:
- ensure the intr setting register is set by flushing posted values
- call synchronize_irq() after that

Also flush stop tx write, inform callers of the tx stop about still
pending transfers (unsuccessful stop) and finally don't wait another
3ms in ath5k_rx_stop, since ath5k_hw_stop_rx_dma ensures transfer to
be finished.

Make sure all writes will be ordered in respect to locks by mmiowb().
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't forget to kill tasklets on stop to not panic if they
fire after freeing some structures.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When signal is noisy, hardware can use all RX buffers and since the last
entry in the list is self-linked, it overwrites the entry until we link
new buffers.

Ensure that we don't free this last one until we are 100% sure that it
is not used by the hardware anymore to not cause memory curruption as
can be seen below.

This is done by checking next buffer in the list. Even after that we
know that the hardware refetched the new link and proceeded further
(the next buffer is ready) we can finally free the overwritten buffer.

We discard it since the status in its descriptor is overwritten (OR-ed
by new status) too.

=============================================================================
BUG kmalloc-4096: Poison overwritten
-----------------------------------------------------------------------------

INFO: 0xffff810067419060-0xffff810067419667. First byte 0x8 instead of 0x6b
INFO: Allocated in dev_alloc_skb+0x18/0x30 age=1118 cpu=1 pid=0
INFO: Freed in skb_release_data+0x85/0xd0 age=1105 cpu=1 pid=3718
INFO: Slab 0xffffe200019d0600 objects=7 used=0 fp=0xffff810067419048 flags=0x40000000000020c3
INFO: Object 0xffff810067419048 @offset=4168 fp=0xffff81006741c120

Bytes b4 0xffff810067419038:  4f 0b 02 00 01 00 00 00 5a 5a 5a 5a 5a 5a 5a 5a O.......ZZZZZZZZ
  Object 0xffff810067419048:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xffff810067419058:  6b 6b 6b 6b 6b 6b 6b 6b 08 42 30 00 00 0b 6b 80 kkkkkkkk.B0...k.
  Object 0xffff810067419068:  f0 5d 00 4f 62 08 a3 64 00 0c 42 16 52 e4 f0 5a 360].Ob.243d..B.R344360Z
  Object 0xffff810067419078:  68 81 00 00 7b a5 b4 be 7d 3b 8f 53 cd d5 de 12 h...{245264276};.S315325336.
  Object 0xffff810067419088:  96 10 0b 89 48 54 23 41 0f 4e 2d b9 37 c3 cb 29 ....HT#A.N-2717303313)
  Object 0xffff810067419098:  d1 e0 de 14 8a 57 2a cc 3b 44 0d 78 7a 19 12 15 321340336..W*314;D.xz...
  Object 0xffff8100674190a8:  a9 ec d4 35 a8 10 ec 8c 40 a7 06 0a 51 a7 48 bb 2513543245250.354.@247..Q247H273
  Object 0xffff8100674190b8:  3e cf a1 c7 38 60 63 3f 51 15 c7 20 eb ba 65 30 >ϡ3078`c?Q.307.353272e0
 Redzone 0xffff81006741a048:  bb bb bb bb bb bb bb bb                         273273273273273273273273
 Padding 0xffff81006741a088:  5a 5a 5a 5a 5a 5a 5a 5a                         ZZZZZZZZ
Pid: 3297, comm: ath5k_pci Not tainted 2.6.26-rc8-mm1_64 #427

Call Trace:
 [<ffffffff802a7306>] print_trailer+0xf6/0x150
 [<ffffffff802a7485>] check_bytes_and_report+0x125/0x180
 [<ffffffff802a75dc>] check_object+0xac/0x260
 [<ffffffff802a9308>] __slab_alloc+0x368/0x6d0
 [<ffffffff80544f82>] ? wireless_send_event+0x142/0x310
 [<ffffffff804b1bd4>] ? __alloc_skb+0x44/0x150
 [<ffffffff80544f82>] ? wireless_send_event+0x142/0x310
 [<ffffffff802aa853>] __kmalloc_track_caller+0xc3/0xf0
 [<ffffffff804b1bfe>] __alloc_skb+0x6e/0x150
[... stack snipped]

FIX kmalloc-4096: Restoring 0xffff810067419060-0xffff810067419667=0x6b

FIX kmalloc-4096: Marking all objects used
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I forgot this in the previous patch that made it unused.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: Ensure we call nfs_sb_deactive() after releasing the directory inode
  nfs_remount oops when rebooting + possible fix

* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
  x86: fix cpu hotplug on 32bit

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] Fix shared mmap when more than two maps of the same file exist
  [ARM] fix VIPT/VIVT macro optimisations, add comments
  [ARM] 5179/1: Replace obsolete IRQT_* and __IRQT_* values with IRQ_TYPE_*
  [ARM] update defconfig for eseries.
  [ARM] PXA: squash warning in pxafb
  [ARM] pxa: PXA25x UDC - Fix warning during build
  [ARM] fix nwflash.c: 6ee8928d
  [ARM] fix IOP32x, IOP33x, MXC and Samsung builds
  [ARM] pci: provide dummy pci_get_legacy_ide_irq()
  [ARM] fix fls() for 64-bit arguments
  [ARM] fix mode for board-yl-9200.c
  [ARM] 5176/1: arm/Makefile: fix: ARM946T -> ARM946E

Simplify the code of include/linux/task_io_accounting.h.

It is also more reasonable to have all the task i/o-related statistics in a
single struct (task_io_accounting).
Signed-off-by: NAndrea Righi <righi.andrea@gmail.com>
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In order to avoid the "Busy inodes after unmount" error message, we need to
ensure that nfs_async_unlink_release() releases the super block after the
call to nfs_free_unlinkdata().
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Jeff, Trond,

The commit

48b605f8 (NFS: implement option checking
when remounting NFS filesystems (resend))

generate an Oops on my platform when rebooting while its root FS on
an NFS share (NFSv3, TCP) :

Unmounting local filesystems...done.
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c3d00000
[00000000] *pgd=a3d72031, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1]
Modules linked in: cpufreq_powersave cpufreq_ondemand cpufreq_userspace cpufreq_conservative ext3 jbd sd_mod pata_pcmcia libata scsi_mod pcmcia loop firmware_class pxafb cfbcopyarea cfbimgblt cfbfillrect pxa2xx_cs pxa2xx_core pcmcia_core snd_pxa2xx_ac97 snd_ac97_codec ac97_bus snd_pxa2xx_pcm snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd isp116x_hcd soundcore rtc_sa1100 snd_page_alloc pxa25x_udc usbcore rtc_ds1307 rtc_core
CPU: 0    Not tainted  (2.6.26-03414-g33af79d1-dirty #15)
PC is at nfs_remount+0x40/0x264
LR is at do_remount_sb+0x158/0x194
pc : [<c00bbf54>]    lr : [<c0076c40>]    psr: 60000013
sp : c2dd1e70  ip : c2dd1e98  fp : c2dd1e94
r10: 00000040  r9 : c3d17000  r8 : c3c3fc40
r7 : 00000000  r6 : 00000000  r5 : c3d2b200  r4 : 00000000
r3 : 00000003  r2 : 00000000  r1 : c2dd1e9c  r0 : c3c3fc00
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 0000397f  Table: a3d00000  DAC: 00000015
Process mount (pid: 1462, stack limit = 0xc2dd0270)
Stack: (0xc2dd1e70 to 0xc2dd2000)
1e60:                                     00000000 c3c3fc00 00000000 00000000
1e80: c3c3fc40 c3d17000 c2dd1ebc c2dd1e98 c0076c40 c00bbf20 c01c61e4 00000001
1ea0: c2dd1ebc 00000001 c3c3fc00 c2dd1ef0 c2dd1ee4 c2dd1ec0 c008c6d8 c0076af4
1ec0: 00000021 00000040 c2dd1ef0 c3d77000 c3eaa000 00000000 c2dd1f6c c2dd1ee8
1ee0: c008d1bc c008c5f8 00000000 c2dd0000 c3c0c320 c3805b38 c002064c 0001f820
1f00: 0001f810 00000001 00000001 00000000 c2dd0000 00000000 c2dd1f34 c2dd1f28
1f20: c005ead8 c005e6f8 c2dd1f44 c2dd1f38 c005eaf8 c005ead0 c2dd1f6c c2dd1f48
1f40: c008ae3c 00000000 c3d77000 0001f810 c0ed0021 c0020ca8 c2dd0000 00000000
1f60: c2dd1fa4 c2dd1f70 c008d2d4 c008d0bc 00000000 0001f810 c2dd1f9c c3eaa000
1f80: c3d17000 00000000 00000000 be8b6aa8 be8b6ad0 00000015 00000000 c2dd1fa8
1fa0: c0020b00 c008d254 00000000 be8b6aa8 0001f810 0001f820 0001f830 c0ed0021
1fc0: 00000000 be8b6aa8 be8b6ad0 00000015 00000000 be8b6ad0 0001f810 be8b6aa8
1fe0: 0001f810 be8b6964 0000aab8 40125124 60000010 0001f810 00000000 00000000
Backtrace:
[<c00bbf14>] (nfs_remount+0x0/0x264) from [<c0076c40>] (do_remount_sb+0x158/0x194)
  r9:c3d17000 r8:c3c3fc40 r7:00000000 r6:00000000 r5:c3c3fc00
r4:00000000
[<c0076ae8>] (do_remount_sb+0x0/0x194) from [<c008c6d8>] (do_remount+0xec/0x118)
  r6:c2dd1ef0 r5:c3c3fc00 r4:00000001
[<c008c5ec>] (do_remount+0x0/0x118) from [<c008d1bc>] (do_mount+0x10c/0x198)
[<c008d0b0>] (do_mount+0x0/0x198) from [<c008d2d4>] (sys_mount+0x8c/0xd4)
[<c008d248>] (sys_mount+0x0/0xd4) from [<c0020b00>] (ret_fast_syscall+0x0/0x2c)
  r7:00000015 r6:be8b6ad0 r5:be8b6aa8 r4:00000000
Code: 0a000086 ea000006 e3530003 8a000004 (e5923000)
---[ end trace 55e1b689cf8c8a6a ]---
------------[ cut here ]------------
WARNING: at kernel/exit.c:966 do_exit+0x3c/0x628()
Modules linked in: cpufreq_powersave cpufreq_ondemand cpufreq_userspace cpufreq_conservative ext3 jbd sd_mod pata_pcmcia libata scsi_mod pcmcia loop firmware_class pxafb cfbcopyarea cfbimgblt cfbfillrect pxa2xx_cs pxa2xx_core pcmcia_core snd_pxa2xx_ac97 snd_ac97_codec ac97_bus snd_pxa2xx_pcm snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd isp116x_hcd soundcore rtc_sa1100 snd_page_alloc pxa25x_udc usbcore rtc_ds1307 rtc_core
[<c0025168>] (dump_stack+0x0/0x14) from [<c0032154>] (warn_on_slowpath+0x4c/0x68)
[<c0032108>] (warn_on_slowpath+0x0/0x68) from [<c003531c>] (do_exit+0x3c/0x628)
  r6:0000000b r5:c3c3dc80 r4:c2dd0000
[<c00352e0>] (do_exit+0x0/0x628) from [<c0025004>] (die+0x2b0/0x30c)
[<c0024d54>] (die+0x0/0x30c) from [<c00270bc>] (__do_kernel_fault+0x6c/0x80)
[<c0027050>] (__do_kernel_fault+0x0/0x80) from [<c00272e0>] (do_page_fault+0x210/0x230)
  r7:c3fa7118 r6:c3c3dc80 r5:c3d166a8 r4:00010000
[<c00270d0>] (do_page_fault+0x0/0x230) from [<c00201ec>] (do_DataAbort+0x3c/0xa0)
[<c00201b0>] (do_DataAbort+0x0/0xa0) from [<c002064c>] (__dabt_svc+0x4c/0x60)
Exception stack(0xc2dd1e28 to 0xc2dd1e70)
1e20:                   c3c3fc00 c2dd1e9c 00000000 00000003 00000000 c3d2b200
1e40: 00000000 00000000 c3c3fc40 c3d17000 00000040 c2dd1e94 c2dd1e98 c2dd1e70
1e60: c0076c40 c00bbf54 60000013 ffffffff
  r8:c3c3fc40 r7:00000000 r6:00000000 r5:c2dd1e5c r4:ffffffff
[<c00bbf14>] (nfs_remount+0x0/0x264) from [<c0076c40>] (do_remount_sb+0x158/0x194)
  r9:c3d17000 r8:c3c3fc40 r7:00000000 r6:00000000 r5:c3c3fc00
r4:00000000
[<c0076ae8>] (do_remount_sb+0x0/0x194) from [<c008c6d8>] (do_remount+0xec/0x118)
  r6:c2dd1ef0 r5:c3c3fc00 r4:00000001
[<c008c5ec>] (do_remount+0x0/0x118) from [<c008d1bc>] (do_mount+0x10c/0x198)
[<c008d0b0>] (do_mount+0x0/0x198) from [<c008d2d4>] (sys_mount+0x8c/0xd4)
[<c008d248>] (sys_mount+0x0/0xd4) from [<c0020b00>] (ret_fast_syscall+0x0/0x2c)
  r7:00000015 r6:be8b6ad0 r5:be8b6aa8 r4:00000000
---[ end trace 55e1b689cf8c8a6a ]---
/etc/rc6.d/S60umountroot: line 17:  1462 Segmentation fault      mount $MOUNT_FORCE_OPT -n -o remount,ro -t dummytype dummydev / 2> /dev/null

The new super.c:nfs_remount function doesn't check the validity of the
options/options4 pointers. Unfortunately, this seems to happend.
The obvious patch seems to check the pointers, and not to do anything if
the happend to be NULL.

Tested on an XScale PXA255 system, latest git.

Regards,

	M.
Signed-off-by: NMarc Zyngier <marc.zyngier@altran.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

commit 3e970473 ("x86: boot secondary
cpus through initial_code") causes the kernel to crash when a CPU is
brought online after the read only sections have been write
protected. The write to initial_code in do_boot_cpu() fails.

Move inital_code to .cpuinit.data section.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NH. Peter Anvin <hpa@zytor.com>