If a QP is attached to a shared receive queue (SRQ), then it doesn't
have a receive queue (RQ).  So don't allocate an RQ doorbell (or map a
doorbell from userspace for userspace QPs) for that QP.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.

This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
   getting them indirectly

Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
   they don't need sched.h
b) sched.h stops being dependency for significant number of files:
   on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
   after patch it's only 3744 (-8.3%).

Cross-compile tested on

	all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
	alpha alpha-up
	arm
	i386 i386-up i386-defconfig i386-allnoconfig
	ia64 ia64-up
	m68k
	mips
	parisc parisc-up
	powerpc powerpc-up
	s390 s390-up
	sparc sparc-up
	sparc64 sparc64-up
	um-x86_64
	x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig

as well as my two usual configs.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make mlx4_post_srq_recv() fail if the SRQ is full (head == tail).
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Pass the number of WQEs for the send queue and their size from userspace
to the kernel to avoid having to keep the QP size calculations in sync 
between the kernel driver and libmlx4.  This fixes a bug seen with the 
current mlx4_ib driver and current libmlx4 caused by a difference in the 
calculated sizes for SQ WQEs.  Also, this gives more flexibility for 
userspace to experiment with using multiple WQE BBs for a single SQ WQE.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

wr->opcode is invalid if it's >= ARRAY_SIZE(mlx4_ib_opcode), not just
strictly >.

This was spotted by the Coverity checker (CID 1643).
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

According to the IB spec, a QP can be moved from RESET back to RESET
or to the ERROR state, but mlx4 firmware does not support this and
returns an error if we try.  Fix the RESET to RESET transition by
just returning 0 without doing anything, and fix RESET to ERROR by
moving the QP from RESET to INIT with dummy parameters and then
transitioning from INIT to ERROR.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

According to the IB spec, a QP can be moved from RESET to the ERROR 
state, but mthca firmware does not support this and returns an error if 
we try.  Work around this FW limitation by moving the QP from RESET to
INIT with dummy parameters and then transitioning from INIT to ERROR.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This is the same issue discovered in mthca by Rolf Manderscheid
<rvm@obsidianresearch.com>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Global CM packets used by rmda_cm were being sent with a GRH:hopLimit
of zero, causing them to be dropped by the router.  The problem is a
missing initialization of the hop_limit field in mthca_read_ah(),
which was called by build_mlx_header() when sending a MAD on QP1.
Signed-off-by: NRolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

max_qp_dest_rdma is already in natural units - no need to shift.  This
was discovered by a test that deliberately requests more outstanding
atomic operation than the device supports.

Found by Sagi Rotem at Mellanox.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Set the return code of ehca_register_mr() to ENOMEM if the corresponding
firmware call fails due to out of resources.  Some other error codes
were explicitly mapped to EINVAL -- just remove those cases so they
get mapped to the default case, which already returns EINVAL anyway.
Signed-off-by: NHoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Lockdep found the following potential deadlock between mcast_lock and
n_mcast_grps_lock: mcast_lock is taken from both interrupt context and
process context, so spin_lock_irqsave() must be used to take it.
n_mcast_grps_lock is only taken from process context, so at first it
seems safe to take it with plain spin_lock(); however, it also nests
inside mcast_lock, and hence we could deadlock:

  cpu A                                   cpu B
    ipath_mcast_add():
      spin_lock_irq(&mcast_lock);

                                            ipath_mcast_detach():
                                              spin_lock(&n_mcast_grps_lock);

                                            <enter interrupt>

                                            ipath_mcast_find():
                                              spin_lock_irqsave(&mcast_lock);

      spin_lock(&n_mcast_grps_lock);

Fix this by using spin_lock_irq() to take n_mcast_grps_lock.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

mthca_cq_clean() updates the CQ consumer index without moving CQEs
back to HW ownership.  As a result, the same WRID might get reported
twice, resulting in a use-after-free.  This was observed in IPoIB CM.
Fix by moving all freed CQEs to HW ownership.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=617>
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix posting lists of > 255 receive WRs for Tavor: rq.next_ind must
be updated each doorbell, otherwise the next doorbell will use an
incorrect index.

Found by Ronni Zimmermann at Mellanox.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- Scaling code is still considered experimental, so disable it by default
- Increase version to SVNEHCA_0023
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

eHCA's sysfs attributes are now being created via sysfs_create_group(),
making the process neatly table-driven. The return value is checked, thus
fixing a few compiler warnings.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- In ehca_process_eq(), we're IRQ safe throughout the whole function, so we
  don't need another _irqsave in the middle of flight.

- take_over_work() is only called by comp_pool_callback(), so it can move
  into the same #ifdef block.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

AQP0/1 should report qp_num={0|1} and the actual QP# should be stored
in struct ehca_qp, not the other way round.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The driver needs to always supply the "GRH present" flag to the
hypervisor, whether it's true or false. Not supplying it (i.e. not
setting the corresponding mask bit) amounts to a "perhaps", which we
don't want.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Some pSeries hypervisor versions show a race condition in the allocate
MR hCall.  Serialize this call per adapter to circumvent this problem.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Once upon a time, GPIO interrupts were rare.  But then a chip bug in
the waldo series forced the use of a GPIO interrupt to signal packet
reception.  This greatly increased the frequency of GPIO interrupts
which have the gpio_mask bits set on the waldo chips.  Other bits in
the gpio_status register are used for I2C clock and data lines, these
bits are usually on.  An "unlikely" annotation leftover from the old
days was improperly applied to these bits, and an unnecessary chip
mmio read was being accessed in the interrupt fast path on waldo.

Remove the stagnant unlikely annotation in the interrupt handler and
keep a shadow copy of the gpio_mask register to avoid the slow mmio
read when testing for interruptable GPIO bits.
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

uar_lock spinlock was used in mlx4_ib_cq_arm without being initialized
(this only affects 32-bit archs, because uar_lock is not used on
64-bit archs and MLX4_INIT_DOORBELL_LOCK() is a NOP).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Since nonboot CPUs are now disabled after tasks and devices have been
frozen and the CPU hotplug infrastructure is used for this purpose, we need
special CPU hotplug notifications that will help the CPU-hotplug-aware
subsystems distinguish normal CPU hotplug events from CPU hotplug events
related to a system-wide suspend or resume operation in progress.  This
patch introduces such notifications and causes them to be used during
suspend and resume transitions.  It also changes all of the
CPU-hotplug-aware subsystems to take these notifications into consideration
(for now they are handled in the same way as the corresponding "normal"
ones).

[oleg@tv-sign.ru: cleanups]
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add an InfiniBand driver for Mellanox ConnectX adapters.  Because
these adapters can also be used as ethernet NICs and Fibre Channel 
HBAs, the driver is split into two modules: 
 
  mlx4_core: Handles low-level things like device initialization and 
    processing firmware commands.  Also controls resource allocation 
    so that the InfiniBand, ethernet and FC functions can share a 
    device without stepping on each other. 
 
  mlx4_ib: Handles InfiniBand-specific things; plugs into the 
    InfiniBand midlayer. 
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Export ib_umem_get()/ib_umem_release() and put low-level drivers in
control of when to call ib_umem_get() to pin and DMA map userspace,
rather than always calling it in ib_uverbs_reg_mr() before calling the
low-level driver's reg_user_mr method.

Also move these functions to be in the ib_core module instead of
ib_uverbs, so that driver modules using them do not depend on
ib_uverbs.

This has a number of advantages:
 - It is better design from the standpoint of making generic code a
   library that can be used or overridden by device-specific code as
   the details of specific devices dictate.
 - Drivers that do not need to pin userspace memory regions do not
   need to take the performance hit of calling ib_mem_get().  For
   example, although I have not tried to implement it in this patch,
   the ipath driver should be able to avoid pinning memory and just
   use copy_{to,from}_user() to access userspace memory regions.
 - Buffers that need special mapping treatment can be identified by
   the low-level driver.  For example, it may be possible to solve
   some Altix-specific memory ordering issues with mthca CQs in
   userspace by mapping CQ buffers with extra flags.
 - Drivers that need to pin and DMA map userspace memory for things
   other than memory regions can use ib_umem_get() directly, instead
   of hacks using extra parameters to their reg_phys_mr method.  For
   example, the mlx4 driver that is pending being merged needs to pin
   and DMA map QP and CQ buffers, but it does not need to create a
   memory key for these buffers.  So the cleanest solution is for mlx4
   to call ib_umem_get() in the create_qp and create_cq methods.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch makes it so that simple_fill_super and get_sb_pseudo assign their
root inodes to be number 1.  It also fixes up a couple of callers of
simple_fill_super that were passing in files arrays that had an index at
number 1, and adds a warning for any caller that sends in such an array.

It would have been nice to have made it so that it wasn't possible to make
such a collision, but some callers need to be able to control what inode
number their entries get, so I think this is the best that can be done.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The semantics defined by the InfiniBand specification say that
completion events are only generated when a completions is added to a
completion queue (CQ) after completion notification is requested.  In
other words, this means that the following race is possible:

	while (CQ is not empty)
		ib_poll_cq(CQ);
	// new completion is added after while loop is exited
	ib_req_notify_cq(CQ);
	// no event is generated for the existing completion

To close this race, the IB spec recommends doing another poll of the
CQ after requesting notification.

However, it is not always possible to arrange code this way (for
example, we have found that NAPI for IPoIB cannot poll after
requesting notification).  Also, some hardware (eg Mellanox HCAs)
actually will generate an event for completions added before the call
to ib_req_notify_cq() -- which is allowed by the spec, since there's
no way for any upper-layer consumer to know exactly when a completion
was really added -- so the extra poll of the CQ is just a waste.

Motivated by this, we add a new flag "IB_CQ_REPORT_MISSED_EVENTS" for
ib_req_notify_cq() so that it can return a hint about whether the a
completion may have been added before the request for notification.
The return value of ib_req_notify_cq() is extended so:

	 < 0	means an error occurred while requesting notification
	== 0	means notification was requested successfully, and if
		IB_CQ_REPORT_MISSED_EVENTS was passed in, then no
		events were missed and it is safe to wait for another
		event.
	 > 0	is only returned if IB_CQ_REPORT_MISSED_EVENTS was
		passed in.  It means that the consumer must poll the
		CQ again to make sure it is empty to avoid the race
		described above.

We add a flag to enable this behavior rather than turning it on
unconditionally, because checking for missed events may incur
significant overhead for some low-level drivers, and consumers that
don't care about the results of this test shouldn't be forced to pay
for the test.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API.  Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value.  Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.

We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity.  This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix a problem where simple ACKs can be sent ahead of RDMA read
responses thus implicitly NAKing the RDMA read.
Signed-off-by: NRalph Campbell <ralph.cambpell@qlogic.com>
Signed-off-by: NRobert Walsh <robert.walsh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix a missing unlock in ipath_rc_rcv_resp() and remove an extra unlock
from ipath_rc_rcv_error().
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The HW now posts 2 ABORT_RPL and/or PEER_ABORT_REQ messages.  We need
to handle them by silenty dropping the 1st but mark that we're ready
for the final message.  This plugs some close races between the uP and
HW.  Also update the minimum required firmware version.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.

In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.

My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:

arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c

I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.

Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
  [PATCH] scatterlist.h needs types.h
  http://lkml.org/lkml/2007/3/01/141Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These are all the remaining instances of get_property.  Simple rename of
get_property to of_get_property.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix TERMINATE layer, type, and ecode values based on
conformance testing.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix the pending mmap code so it doesn't corrupt the list of pending
mmaps and crash the machine when pending mmaps are destroyed without
first being mapped.  Also, remove an unused variable, and use standard
kernel lists instead of our own homebrewed linked list implementation
to keep the pending mmap list.
Signed-off-by: NRobert Walsh <robert.walsh@qlogic.com>
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

With mthca, RC QPs can starve each other and even UD QPs on the same
hardware schedule queue.  As a result, userspace MPI can starve
e.g. IPoIB traffic, with netdev watchdog warnings getting printed out,
and TCP connections getting stuck or failing.

Reduce the chance of this happening by using three separate hardware
schedule queues: one for userspace RC QPs, one for kernel RC QPs, and
one for all other QPs.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This fixes a problem which causes too many RC timeouts and
retransmits.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>