zero rx_filter_enabled array after recovery to avoid
cases were the driver will keep trying to clear a
filter which is not configured in FW.

Such case will cause consecutive recoveries due to
command execution failures.

While on it, convert rx_filter_enabled to bitmap,
to save some memory and make sparse happy (it
doesn't like sizeof(bool array)).
Signed-off-by: NNadim Zubidat <nadimz@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use ieee80211_channel_to_frequency() to replace b43_channel_to_freq_{2,5}ghz(),
and remove unused b43_freq_to_channel_{2,5}ghz().
Signed-off-by: NZHAO Gang <gamerh2o@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds key material V2 support to mwifiex.
Newer FW supports this feature and FW KEY API version is used
to determine which command structure needs to be used.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support to parse FW API version TLVs.
Currently only API version for key_material is supported.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During deauthenticate/link lost event, disable all TDLS links as
TDLS would not work when infra connection is not active.
Also this will avoid an issue where ping to peer station doesn't
work after reassociation to AP where we had created TDLS link in
earlier association.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If TDLS link is 11ac enabled i.e. we as well as peer station
supports VHT, configure seprate TX & RX window sizes during
BA setup. So even if BSS does not support 11ac, we can use VHT
capabilities and higher window sizes on direct link.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During TDLS setup request/response, if HW is 11ac capable,
we add VHT Capability IEs in outgoing data frame. Also while
processing received setup request/response, we preserve peer's
11ac capability retrieved from IEs.

Patch also gets VHT parameters from config_station handlers and
sets it to FW using TDLS config command.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch changes mwifiex_fill_vht_cap_tlv function to pass
struct ieee80211_vht_cap instead of mwifiex_ie_types_vhtcap
so that it can be used generically.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds AMPDU support for TDLS link. We have set 11n
capabilities including AMPDU parameters during ENABLE_LINK.
We set a variable in RA list to indicate this as TDLS link.
This patch uses these capabilities to know if AMPDU is allowed
on TDLS link and enables AMPDU aggregation for TX and RX reording
support for RA list for this peer.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

1. If data packet is addressed to TDLS peer for which link is
established, mark these packets with TDLS flag so that FW can
send them on direct link instead of sending via AP.
2. If data packet is addressed to TDLS peer and TDLS setup is
underway, move these packets to TDLS queue.
3. If this packet is TDLS setup packet, do not block it.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While TDLS link is being setup, few packets from this station to
peer station may be buffered at AP. It may happen that once TDLS
link is setup, packets sent from station to peer on direct link
get delivered before traffic from AP arrives at peer station.
This results into packet reordering issue at peer station.

To avoid this, we hold data packets destined to TDLS peer during
TDLS setup. These packets are moved to temperory TDLS TX queue.
Upon successful TDLS setup, they are moved to RA list created for
this peer. Upon failure, packets are moved back to AP's RA list
for that particular TID.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds cfg80211 change_station handler support for mwifiex
which is needed for TDLS link setup. Driver creates a command to
modify peer link capabilities and issues command to FW.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds cfg80211 add_station handler support for mwifiex
which is needed for TDLS setup. Driver issues create TDLS link
command to FW upon receiving add_station from cfg80211.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds cfg80211 handler tdls_oper handler support to
mwifiex. Upon enable link, driver sets status as TDLS status as
setup complete and also sets AMSDU size, AMPDU params for direct
link. Upon disable link, driver issues command to FW to delete
this link in FW.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for parsing TDLS action frames during
station receive handler.
Peer station capabilities are stored into station node.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for TDLS management frames transmit
handler. mwifiex driver supports TDLS with external support,
i.e. expects user space application to form TDLS frames.
Same is advertised to cfg80211 during registration.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Pass 'struct ieee80211_ht_cap' pointer to
mwifiex_fill_cap_info() instead of
'struct mwifiex_ie_types_htcap' pointer, because the routine
internally uses the later one.
This patch also adds WARN_ON_ONCE check for NULL band.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These functions are now needed by TDLS while managing station list.
Move them from AP related file to utility file.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

tos_to_tid_inv values are needed even during TDLS restore
operations. Currently tos_to_tid_inv is part of wmm.c and
is declared static.
Make it part of private structure so that it can be used in
other files as well.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bug where we were checking for AP's AMPDU param
setting even when transmitting traffic to associated station.
Patch adds provision to pass additional parameter ra_list pointer
to function which checks if AMPDU is allowed. If current BSS type is
AP, we check station's AMPDU params else we check AP's AMPDU params.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently MU/SU beamformer and MU beamformee features are
not supported.

Hence this patch modifies VHT capability information accordingly.
Number of sounding dimensions should be zero in this case.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch makes sure that beamforming capability field in
ht capability info gets filled if hardware supports the feature.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current mwifiex pcie driver assumed that it would get
its cmdrsp_complete() callback called before another command
was sent to unmap the command's skbuff. However, that is not
true. The mwifiex_check_ps_cond() will send a sleep command
to the card without having adapter->curr_cmd set. Within the
workqueue's state machine the adapter's state would be set
to allow commands (curr_cmd = NULL && cmd_sent = false) after
having receieved the response from the sleep command. The
card->cmd_buf would then be overridden with the new command
but the first command's skbuff was not unmapped. This leaks
mapped skbuffs when a bounce buffer is employed.

To rectify this unmap the card->cmd_buf when the response is
received from the card instead of waiting for the
cmdrsp_complete() callback.
Signed-off-by: NAaron Durbin <adurbin@chromium.org>
Reviewed-by: NPaul Stewart <pstew@chromium.org>
Reviewed-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Depending on the underlying DMA implementation its
not possible to partially unmap DMA buffers. Moreover
its not possible to understand the intent of passing
0 as the size to dma unmap. The intent of this
driver is unmap the entire skb buffer. The only way
to ensure that the size matches on unmap is to store
both the dma address and the size in the skb ca field.

Introduce a mwifiex_dma_mapping structure which tracks
the dma address and the size. Additionally, provide
a mwifiex_unmap_pci_memory() that utilizes the new
structure. This also provide symmetry within the
internal API.
Signed-off-by: NAaron Durbin <adurbin@chromium.org>
Reviewed-by: NPaul Stewart <pstew@chromium.org>
Reviewed-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In extended scan, host gets scan results through one or
multiple events instead of scan command response. Host will
send next scan command when all the events are received.

Legacy scan sometimes truncates scan results in a noisy
environment due to buffer length limitation. This issue
is addressed in extended scan.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This new function will be useful later for extended scan
feature.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This new function will be useful later for extended scan
feature.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'mwifiex_bcn_param' structure contains five parameters which
are present in beacon buffer in case of legacy scan.

'rssi' field won't be there in this buffer for extended scan.
Hence 'bssid' and 'rssi' are removed from the structure and it is
renamed as 'mwifiex_fixed_bcn_param' so that we can have common
parsing logic later for both.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bit12 in fw_cap_info is for testing only.
Remove all related code.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

1) rename max_mcs to mcs;
2) initialize 'i' and 'nss' as 1 instead of 0 in nss lookup;
3) use GET_VHTNSSMCS(mcs_map, nss) macro;
4) use IEEE80211_VHT_MCS_* definitions instead of hard coding
Reported-by: NPaul Stewart <pstew@chromium.org>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove these local array variables and define them as static
const array in global space.
The duplicated mcs_rate table is removed automatically with this
change.
Reported-by: NPaul Stewart <pstew@chromium.org>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove driver's macro and use ieee80211's definition instead
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a routine to calculate the median IQ correction
values for AR955x, which is used for outlier detection.
The normal method which is used for all other chips is
bypassed for AR955x.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will be used for storing data for mutiple
IQ calibration runs, for AR955x.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IQ calibration post-processing for AR955x is different
from other chips - instead of just doing it as part
of AGC calibration once, it is triggered 3 times and
a median is determined. This patch adds initial support
for changing the calibration behavior for AR955x.

Also, to simplify things, a helper routine to issue/poll
AGC calibration is used.

For non-AR955x chips, the iqcal_idx (which will be used
in subsequent patches) is set to zero.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Incorrect values are programmed in the registers
containing the IQ correction coefficients by the IQ-CAL
post-processing code. Fix this.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use ar9003_hw_tx_iq_cal_outlier_detection instead.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In chips like AR955x, the initvals contain the information
whether IQ calibration is to be done in the HW when an
AGC calibration is triggered. Check if IQ-CAL is enabled
in the initvals before flagging 'txiqcal_done' as true.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Calibration data is not reused for SoC chips, so
call ar9003_hw_tx_iq_cal_post_proc() with the correct
argument. The 'is_reusable' flag is currently used
only for PC-OEM chips, but it makes things clearer to
specify it explicity.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>