Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add DCAN sleep pins to save some power during suspend.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

STI drm drivers probe and bind using component framework was incorrect.
In addition to drivers fix DT update is needed to make all sub-components
become childs of sti-display-subsystem.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

"ARM: dts: <omap2/omap4/omap5/dra7>: add minimal l4 bus
layout with control module support" moved pbias_regulator dt node
from being a child node of ocp to be the child node of
'syscon'. Since 'syscon' doesn't have the 'ranges' property,
address translation fails while trying to convert the address
to resource. Fix it here by populating 'ranges' property in
syscon dt node.

Fixes: 72b10ac0 ("ARM: dts: omap24xx: add minimal l4 bus
layout with control module support")

Fixes: 7415b0b4 ("ARM: dts: omap4: add minimal l4 bus layout
with control module support")

Fixes: ed8509ed ("ARM: dts: omap5: add minimal l4 bus
layout with control module support")

Fixes: d919501f ("ARM: dts: dra7: add minimal l4 bus
layout with control module support")
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: fixed omap3 pbias to work]
Signed-off-by: NTony Lindgren <tony@atomide.com>

The VBUS line of USB2 is connected to VBUS detect logic on
the PMIC. Use the palmas-usb driver to report VBUS events
to the USB driver.

As the palmas-usb driver supports GPIO based ID reporting
provide the GPIO for ID pin as well.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The i2c5 pinctrl offsets are wrong. If the bootloader doesn't set the
pins up, communication with tca6424a doesn't work (controller timeouts)
and it is not possible to enable HDMI.

Fixes: 9be495c4 ("ARM: dts: omap5-evm: Add I2c pinctrl data")
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Originally, all the SoC PHY rails were supplied by LDO3. However, as a
result of characterization, it was determined that this posed a risk in
extreme load  conditions. Hence the PHY rails are split between two
different LDOs. Update the related node as a result

LDO3/VDDA_1V8_PHYA supplies vdda_usb1, vdda_usb2, vdda_sata, vdda_usb3
LDO4/VDDA_1V8_PHYB supplies vdda_pcie1, vdda_pcie0, vdda_hdmi, vdda_pcie

NOTE: We break compatibility with pre-production boards with this change
since, the PMIC LDO4 is disabled at OTP level.

The new configuration is the plan of record and all pre-production
boards are supposed to be replaced with the latest boards matching the
mentioned configuration.

Some very few 10 something boards have been created and
stopped production till the latest modifications were done (PMIC USB
interrupt, LDO4 etc) - and all of those boards are now getting
scrapped.. If there are any (as per tracking information, there should
not be any), TI should be contacted to have them replaced.
Signed-off-by: NNishanth Menon <nm@ti.com>
[tony@atomide.com: updated commit about these being TI internal protos]
Signed-off-by: NTony Lindgren <tony@atomide.com>

This fix the model name for the device.
Whole string taken from the HP support center web page
Signed-off-by: NNicolas Chauvet <kwizart@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Register address in name of the node is wrong
Signed-off-by: NVishal Mahaveer <vishalm@ti.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use platform specific compatible strings instead of the common
"ti,pbias-omap" compatible string.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Only the IGEPv2 boards have a LAN9221i chip connected to the GPMC
so the pinmux configuration for the GPIO connected to the IRQ line
of the LAN chip should not be defined in the IGEP common dtsi but
in the one common to the IGEPv2 boards.

While there, use the OMAP3_CORE1_IOPAD() macro for the padconf reg.
Suggested-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With the support in the generic PM framework for wakeirq and capability
added to the rtc-ds1307 driver to support this, we can now define the
optional wakeup irq to allow the RTC to wakeup the system from low power
modes as part of suspend.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix the mpu voltage as it is set too low for the silicon
revision 2.1.
Signed-off-by: NTeresa Remmet <t.remmet@phytec.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For beagle x15, both the vdd and io lines are connected to the
same regulator (ldo1_reg). However vmmc_aux is populated to vdd_3v3.
Remove it.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
[tony@atomide.com: updated to apply]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Looks like I made a typo on the control base, all the 81xx
SoCs have it at 0x48140000 base. We've just gotten away with
the typo as the Ethernet phy was configured by the bootloader
on my test system and we're not yet using the pinctrl.

In addition to fixing the contol base, we need to also use the
right Ethernet phy flags to initialize it. And we are still
missing the PLL driver for dm814x and only relying on the
divider and mux clocks.

Fixes: f3d953ea ("ARM: dts: Add minimal dm814x support")
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Let's fix pinmux address of gpio 170 used by tfp410 powerdown-gpio.

According to the OMAP35x Technical Reference Manual
  CONTROL_PADCONF_I2C3_SDA[15:0]  0x480021C4 mode0: i2c3_sda
  CONTROL_PADCONF_I2C3_SDA[31:16] 0x480021C4 mode4: gpio_170
the pinmux address of gpio 170 must be 0x480021C6.

The former wrong address broke i2c3 (used by hdmi ddc), resulting in
kernel message:
  omap_i2c 48060000.i2c: controller timed out

Fixes: 8cecf52b ("ARM: omap3-beagle.dts: add display information")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: NCarl Frederik Werner <frederik@cfbw.eu>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The ddc-i2c-bus property was missing from the veyron dtsi file since
downstream the ddc-i2c-bus was still being specified in rk3288.dtsi and
nobody noticed when the veyron dtsi was sent upstream.  Add it.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Tested-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

When loading x86 64bit kernel above 4GiB with patched grub2, got kernel
gunzip error.

| early console in decompress_kernel
| decompress_kernel:
|       input: [0x807f2143b4-0x807ff61aee]
|      output: [0x807cc00000-0x807f3ea29b] 0x027ea29c: output_len
| boot via startup_64
| KASLR using RDTSC...
|  new output: [0x46fe000000-0x470138cfff] 0x0338d000: output_run_size
|  decompress: [0x46fe000000-0x47007ea29b] <=== [0x807f2143b4-0x807ff61aee]
|
| Decompressing Linux... gz...
|
| uncompression error
|
| -- System halted

the new buffer is at 0x46fe000000ULL, decompressor_gzip is using
0xffffffb901ffffff as out_len.  gunzip in lib/zlib_inflate/inflate.c cap
that len to 0x01ffffff and decompress fails later.

We could hit this problem with crashkernel booting that uses kexec loading
kernel above 4GiB.

We have decompress_* support:
    1. inbuf[]/outbuf[] for kernel preboot.
    2. inbuf[]/flush() for initramfs
    3. fill()/flush() for initrd.
This bug only affect kernel preboot path that use outbuf[].

Add __decompress and take real out_buf_len for gunzip instead of guessing
wrong buf size.

Fixes: 1431574a (lib/decompressors: fix "no limit" output buffer length)
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Jon Medhurst <tixy@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.

Cc: Tim Bird <tim.bird@sonymobile.com>
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.

Cc: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Use stdout-path so that we don't have to put the console on the
kernel command line.

Cc: Mike Rapoport <mike.rapoport@gmail.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Add a label to the serial nodes that are being used for the
console.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SOC specific and the external
clock is board dependent. Adding the corresponding nodes.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Since the LED modes mapping is no longer hardcoded inside the leds-ns2
driver, then it must be provided through the modes-map property in the
ns2-leds nodes.
Signed-off-by: NVincent Donnefort <vdonnefort@gmail.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>

The base addresses for the Ux500 PRCC controllers are hardcoded,
let's move them to the clock node in the device tree and delete
the constants.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NMichael Turquette <mturquette@baylibre.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Specify how the GPIOs map to the pins in Tegra SoCs, so the dependency is
explicit.
Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Current base address is wrong by 0x04 bytes for AHB bus device as shown
in dmesg:

	tegra-ahb 6000c004.ahb: incorrect AHB base address in DT data - enabling workaround

To correct old DTBs, commit ce7a10b0 ("ARM: 8334/1: amba: tegra-ahb:
detect and correct bogus base address") checks for the low bit of the
base address and removes theses 0x04 bytes at runtime.

This patch fixes the original DTS, so upstream version doesn't need the
workaround of the base address.

As both addresses are valid, this patch doesn't break compatibility.

Tested on tegra20-paz00 (aka ac100).
Signed-off-by: NNicolas Chauvet <kwizart@gmail.com>
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

This patch modifies the device tree for Tegra124 based devices to enable
the Cortex A15 PMU. The interrupt numbers are taken from NVIDIA Tegra K1
TRM (DP-06905-001_v03p). This patch was tested on a Jetson TK1.
Signed-off-by: NKyle Huey <khuey@kylehuey.com>
Acked-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add the device-tree node for the GK20A GPU and leave it disabled.
It is the responsibility of the bootloader to enable it if the
VPR registers have been programmed such that the GPU can operate.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add the device-tree node for the GK20A GPU and leave it disabled.
It is the responsibility of the bootloader to enable it if the
VPR registers have been programmed such that the GPU can operate.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>

Nouveau can make use of the IOMMU to make physical appear linear in the
GPU address space.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Specify the CPU voltage regulator for the cpufreq driver.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: NMikko Perttunen <mikko.perttunen@kapsi.fi>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The Tegra124 cpufreq driver relies on certain clocks being present
in the /cpus/cpu@0 node.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: NMikko Perttunen <mikko.perttunen@kapsi.fi>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add the board-specific properties of the DFLL for the Jetson TK1 board.
On this board, the DFLL will take control of the sd0 regulator on the
on-board AS3722 PMIC.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: NMikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: NMichael Turquette <mturquette@linaro.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>