Provide a frontend setup routine for the PCTV 340e which takes into account
the specific GPIO setup of the board.

Note that this patch does *not* take into account the xc4000 reset pin, which
is attached to the dib7000.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the board profile for the PCTV 340eSE, since that's what I have here
for development.

[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is initial code written by Davide Ferri for the PCTV 340e, including
a new xc4000 driver.  I am checking in all the code unmodified, and making
no assertions about its quality (other than confirming it compiles).

[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NDavide Ferri <davidef1986@gmail.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The implementation of the gain calculation for this sensor is incorrect.
It is only working for the first 127 values.

The reason is, that the gain cannot be set directly by writing a value
into the gain registers of the sensor. The gain register work this way
(see datasheet page 24): bits 0 to 6 are called "initial gain". These
are linear. But bits 7 and 8 ("analog multiplicative factors") and bits
9 and 10 ("digital multiplicative factors") work completely different:
Each of these bits increase the gain by the factor 2. So if the bits
7-10 are 0011, 0110, 1100 or 0101 for example, the gain from bits 0-6 is
multiplied by 4. The order of the bits 7-10 is not important for the
resulting gain. (But there are some recommended values for low noise)

The current driver doesn't do this correctly: If the current gain is 000
0111 1111 (127) and the gain is increased by 1, you would expect the
image to become brighter. But the image is completly dark, because the
new gain is 000 1000 0000 (128). This means: Initial gain of 0,
multiplied by 2. The result is 0.

This patch adds a new function which does the gain calculation and also
fixes the same bug for red_balance and blue_balance. Additionally, the
driver follows the recommendation from the datasheet, which says, that
the gain should always be above 0x0020.
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJohannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are problems when you use this camera/sensor in a very bright room
or outside. The image is completely white, because it is overexposed.
The driver uses a default value which is not suitable for all
environments.

This patch makes it possible to adjust the exposure time by youself. I
found out by logging the i2c-data, that the windows driver for this
sensor is doing this, too. I tested the camera on a sunny day and after
adjusting the exposure time, I was able to see a very good image.
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJohannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

According to the datasheet (page 8), the first optical clear
pixel-column is not at position 14. The correct/recommended value is 20.
Without this patch there is a dark line on the left side of the image.
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJohannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The conversion of winbond-cir to use rc-core seems to have missed a
a few bits and pieces which were in my local tree. Kudos to
Juan Jesús García de Soria Lucena <skandalfo@gmail.com> for noticing.

[mchehab@redhat.com: fix two UTF-8 violations]
Signed-off-by: NDavid Härdeman <david@hardeman.nu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In the original code, if the allocation failed we dereference "rr3"
when it was NULL.
Acked-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If change_protocol() fails and we goto out_raw, then it calls unlock
twice.  I noticed that the other time we called change_protocol() we
held the &dev->lock, so I changed it to hold it here too.
Reviewed-by: NJarod Wilson <jarod@redhat.com>
Acked-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- Add missing entry to array "dtv_cmds".
- Set array size to DTV_MAX_COMMAND + 1 to avoid future off-by-ones.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Otherwise they clutter the dmesg buffer even on a production kernel.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The function "rc5_scan" in "dvb_usb.h" is returning invalid value.
The value should be returned "u16" but is returning "u8".

See example below in "drivers/media/dvb/dvb-usb/opera1.c":

        send_key = (send_key & 0xffff) | 0x0100;

        for (i = 0; i < ARRAY_SIZE(rc_map_opera1_table); i++) {
            if (rc5_scan(&rc_map_opera1_table[i]) == (send_key & 0xffff)) {
                *state = REMOTE_KEY_PRESSED;
                *event = rc_map_opera1_table[i].keycode;
                opst->last_key_pressed =
                    rc_map_opera1_table[i].keycode;
                break;
            }
            opst->last_key_pressed = 0;
        }
Signed-off-by: NManoel Pinheiro <pinusdtv@hotmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert radio-sf16fmr2 to use generic TEA575x implementation. Most of the
driver code goes away as SF16-FMR2 is basically just a TEA5757 tuner
connected to ISA bus.
The card can optionally be equipped with PT2254A volume control (equivalent
of TC9154AP) - the volume setting is completely reworked (with balance control
added) and tested.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The info and err macros are already defined by the USB stack. Rename
these macros to avoid macro redefinition warnings.
Signed-off-by: NHans Petter Selasky <hselasky@c2i.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The dbg, warn and info macros are already defined by the USB stack.
Rename these macros to avoid macro redefinition warnings.

Refactor lineshift in printouts.
Signed-off-by: NHans Petter Selasky <hselasky@c2i.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

radio->int_in_urb is not deallocated on error paths in si470x_usb_driver_probe().

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Petter Selasky <hselasky@c2i.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert tea575x-tuner to use the new V4L2 control framework. Also add
ext_init() callback that can be used by a card driver for additional
initialization right before registering the video device (for SF16-FMR2).

Also embed struct video_device to struct snd_tea575x to simplify the code.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Petter Selasky <hselasky@c2i.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

VIDIOC_S_CTRL and VIDIOC_S_EXT_CTRLS return EACCES when setting a read-only
control VIDIOC_TRY_EXT_CTRLS when trying a read-only control and
VIDIOC_G_CTRL and VIDIOC_G_EXT_CTRLS when getting a write-only control.
Document this.
Signed-off-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On function videobuf_pages_to_sg the statement sg_set_page(&sglist[0],
pages[0], PAGE_SIZE - offset, offset) will fail if size is less than
PAGE_SIZE.
Signed-off-by: NNewson Edouard <newsondev@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

list_first_entry() always returns non-null here.  I think the intent was
to test whether there were any entries in the used list.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Several cardlist entries are missed. Fix them by running some
script magic (about the same scripts we used to have at -hg tree).
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

All boards use EM28xxx_BOARD, to identify that the macro
refers to a card entry. So:

EM2874_LEADERSHIP_ISDBT -> EM2874_BOARD_LEADERSHIP_ISDBT
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

PCTV Systems nanoStick T2 290e => PCTV nanoStick T2 290e
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For some reason it repeats rather slowly, around 800ms intervals,
two RC5 remotes tested.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

error: dubious one-bit signed bitfield
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

kmalloc I2C buffers
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Cc: Dan Carpenter <error27@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Change some info, comments, variables. No functionality changes.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Basically it is just same device as Anysee E7 S2 but made for
internal PCI(e) slot and motherboard USB connector.

Cc: info@anysee.com
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Basically it is just same device as Anysee E7 TC but made for
internal PCI(e) slot and motherboard USB connector.

Cc: info@anysee.com
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This sensor was found in a webcam 8020:ef04 (SVC - SVU2-1.3MV PCCam).
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch addresses several issues pointed by Randy Dunlap
<rdunlap@xenotime.net> at changeset ece722c:

- In the generated index.html file, "media" is listed first, but it
  should be listed in alphabetical order, not first.

- The generated files are (hidden) in .tmpmedia/

- The link from the top-level index.html file to "media" is to
  media/index.html, but the file is actually in .tmpmedia/media/index.html

- Please build docs with and without using "O=builddir" and test that.

- Would it be possible for media to have its own Makefile instead of
  merging into this one?

Due to the way cleandocs target works, I had to rename the media DocBook
to media_api, otherwise cleandocs would remove the /media directory.

Thanks-to: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Auto-generate the videodev2.h.xml,frontend.h.xml and the indexes.

Some logic at the Makefile helps us to identify when a symbol is missing,
like for example:

Error: no ID for constraint linkend: V4L2-PIX-FMT-JPGL.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>