[ Upstream commit f4ce428c41fb22e3ed55496dded94df44cb920fa ]

Fixes: Configure DMA burst size to be same as SPI TX/RX trigger levels
to avoid mismatch.

SPI FIFO trigger levels are calculated based on the transfer length.
So this patch moves DMA slave configuration to happen before start
of DMAs.
Signed-off-by: NSowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit c4fc9e5b28ff787e35137c2cc13316bb11d7657b ]

Fixes: Flush TX and RX FIFOs before start of new transfer and on FIFO
overflow or underrun errors.
Signed-off-by: NSowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 32bd1a9551cae34e6889afa235c7afdfede9aeac ]

Fixes: terminate DMA and perform controller reset on transfer timeout
to clear the FIFO's and errors.
Signed-off-by: NSowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 1a89ac5b91895127f7c586ec5075c3753ca25501 ]

Fixes: computation of actual bytes to fill/receive in/from FIFO in unpacked
mode when transfer length is not a multiple of requested bits per word.

unpacked mode transfers fails when the transfer includes partial bytes in
the last word.

Total words to be written/read to/from FIFO is computed based on transfer
length and bits per word. Unpacked mode includes 0 padding bytes for partial
words to align with bits per word and these extra bytes are also accounted
for calculating bytes left to transfer in the current driver.

This causes extra bytes access of tx/rx buffers along with buffer index
position crossing actual length where remain_len becomes negative and due to
unsigned type, negative value is a 32 bit representation of signed value
and transferred bytes never meets the actual transfer length resulting in
transfer timeout and a hang.

This patch fixes this with proper computation of the actual bytes to fill in
FIFO during transmit and the actual bytes to read from FIFO during receive
ignoring 0 padded bytes.
Signed-off-by: NSowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 7b3d10cdf54b8bc1dc0da21faed9789ac4da3684 ]

Fixes: Clear packed bit when not using packed mode.

Packed bit is not cleared when not using packed mode. This results
in transfer timeouts for the unpacked mode transfers followed by the
packed mode transfers.
Signed-off-by: NSowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 2e7682ebfc750177a4944eeb56e97a3f05734528 ]

'vb' null check should be done before dereferencing it in
tw5864_handle_frame, otherwise a NULL pointer dereference
may occur.

Fixes: 34d1324e ("[media] pci: Add tw5864 driver")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 0e633f97162c1c74c68e2eb20bbd9259dce87cd9 ]

clang warns about a possible variable use that gcc never
complained about:

drivers/media/platform/davinci/isif.c:982:32: error: variable 'frame_size' is uninitialized when used here
      [-Werror,-Wuninitialized]
                dm365_vpss_set_pg_frame_size(frame_size);
                                             ^~~~~~~~~~
drivers/media/platform/davinci/isif.c:887:2: note: variable 'frame_size' is declared here
        struct vpss_pg_frame_size frame_size;
        ^
1 error generated.

There is no initialization for this variable at all, and there
has never been one in the mainline kernel, so we really should
not put that stack data into an mmio register.

On the other hand, I suspect that gcc checks the condition
more closely and notices that the global
isif_cfg.bayer.config_params.test_pat_gen flag is initialized
to zero and never written to from any code path, so anything
depending on it can be eliminated.

To shut up the clang warning, just remove the dead code manually,
it has probably never been used because any attempt to do so
would have resulted in undefined behavior.

Fixes: 63e3ab14 ("V4L/DVB: V4L - vpfe capture - source for ISIF driver on DM365")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NNathan Chancellor <natechancellor@gmail.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 93b260528020792032e50725383f27a27897bb0f ]

The memremap() function doesn't return error pointers, it returns NULL.
This code is returning "ret = PTR_ERR(NULL);" which is success, but it
should return -ENOMEM.

Fixes: 312416d9 ("drivers: qcom: add command DB driver")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NAndy Gross <andy.gross@linaro.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 6146dd453e235c487d85ae4dc6cc08978a1c890f ]

When phylink_of_phy_connect fails, dsa_slave_phy_setup tries to save the
day by connecting to an alternative PHY, none other than a PHY on the
switch's internal MDIO bus, at an address equal to the port's index.

However this does not take into consideration the scenario when the
switch that failed to probe an external PHY does not have an internal
MDIO bus at all.

Fixes: aab9c406 ("net: dsa: Plug in PHYLINK support")
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 7f0d078667a494466991aa7133f49594f32ff6a2 ]

Commit 747834ab ("ARM: OMAP2+: hwmod: revise hardreset behavior") made
the call to _enable() conditional based on no oh->rst_lines_cnt. This
caused the return value to be potentially uninitialized. Curiously we see
no compiler warnings for this, probably as this gets inlined.

We call _setup_reset() from _setup() and only _setup_postsetup() if the
return value is zero. Currently the return value can be uninitialized for
cases where oh->rst_lines_cnt is set and HWMOD_INIT_NO_RESET is not set.

Fixes: 747834ab ("ARM: OMAP2+: hwmod: revise hardreset behavior")
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit d29f5aa0bc0c321e1b9e4658a2a7e08e885da52a ]

So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.

[0] https://marc.info/?t=155264050700001&r=1&w=2

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: NPhil Reid <preid@electromag.com.au>
Tested-by: Nliweihang <liweihang@hisilicon.com>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit c2a5b554751545023056559121a8ecf86aebe541 ]

Commit 1848f3f4 ("ARM: dts: sun9i: Remove GPIO pinctrl nodes to avoid
warnings") was wrong on the optimus, and instead of droping the
pinctrl-names property, it dropped the regulator-name one.

Obviously, that wasn't what was intended. Reinstate regulator-name and drop
pinctrl-names.

Fixes: 1848f3f4 ("ARM: dts: sun9i: Remove GPIO pinctrl nodes to avoid warnings")
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 562bf19611c000cb7219431c3cc78aa60c2b371e ]

The pinctrl binding mandates that we have the three clocks fed into the PIO
described.

Even though the old case is still supported for backward compatibility, we
should update our DTs to fix this.

Fixes: 6bc37fac ("arm64: dts: add Allwinner A64 SoC .dtsi")
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit fa44328f4eb0b762a1fcb148809068e9646e7156 ]

Commit d02752149759 ("ARM: dts: sun8i-a23-a33: Move NAND controller device
node to sort by address") moved the NAND controller node around, but
dropped the default muxing in the process.

Reintroduce it.

Fixes: d02752149759 ("ARM: dts: sun8i-a23-a33: Move NAND controller device node to sort by address")
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 0ca7ce7db771580433bf24454f7a1542bd326078 ]

This resolves some bugs that affect VIA timer counter accesses.
Avoid lost interrupts caused by reading the counter low byte register.
Make allowance for the fact that the counter will be decremented to
0xFFFF before being reloaded.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit a5fdd713d256887b5f012608701149fa939e5645 ]

A statement was originally added in 2006 to shut up a gcc warning,
now but now clang warns about it:

fs/jfs/jfs_txnmgr.c:1932:15: error: variable 'pxd' is uninitialized when used within its own initialization
      [-Werror,-Wuninitialized]
                pxd_t pxd = pxd;        /* truncated extent of xad */
                      ~~~   ^~~

Modern versions of gcc are fine without the silly assignment, so just
drop it. Tested with gcc-4.6 (released 2011), 4.7, 4.8, and 4.9.

Fixes: c9e3ad60 ("JFS: Get rid of "may be used uninitialized" warnings")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 5db46ac29a6797541943d3c4081821747e342732 ]

Building with clang for a 32-bit architecture runs over the stack
frame limit in the setkey function:

drivers/crypto/ccree/cc_cipher.c:318:12: error: stack frame size of 1152 bytes in function 'cc_cipher_setkey' [-Werror,-Wframe-larger-than=]

The problem is that there are two large variables: the temporary
'tmp' array and the SHASH_DESC_ON_STACK() declaration. Moving
the first into the block in which it is used reduces the
total frame size to 768 bytes, which seems more reasonable
and is under the warning limit.

Fixes: 63ee04c8 ("crypto: ccree - add skcipher support")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-By: NGilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit e69b394703e032e56a140172440ec4f9890b536d ]

selector 0xB (1011) should be 2.6V rather than 2.7V, fit ix.

Table 5-4. LDOA1 Output Voltage Options
VID Bits VOUT VID Bits VOUT VID Bits VOUT VID Bits VOUT
0000     1.35 0100     1.8  1000     2.3  1100     2.85
0001     1.5  0101     1.9  1001     2.4  1101     3.0
0010     1.6  0110     2.0  1010     2.5  1110     3.3
0011     1.7  0111     2.1  1011     2.6  1111     Not Used

Fixes: d2a2e729 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit a3d7f22ef34ec4206b50ee121384d5c8bebd5591 ]

Checking of kmalloc() seems to have been committed - as
cx23885_dvb_register() is checking for != 0 return, returning
-ENOMEM should be fine here.  While at it address the coccicheck
suggestion to move to kmemdup rather than using kmalloc+memcpy.

Fixes: 46b21bba ("[media] Add support for DViCO FusionHDTV DVB-T Dual Express2")
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit ef4bb63dc1f7213c08e13f6943c69cd27f69e4a3 ]

We forgot to set "ret" on this error path.

Fixes: e8454ff7 ("[media] drivers:media:radio: wl128x: FM Driver Common sources")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 7afb0df554292dca7568446f619965fb8153085d ]

We should be updating *pos.  The current code is a no-op.

Fixes: 1c1e45d1 ("V4L/DVB (7786): cx18: new driver for the Conexant CX23418 MPEG encoder chip")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit f8e579f3ca0973daef263f513da5edff520a6c0d ]

We had intended to update *pos, but the current code is a no-op.

Fixes: 1a0adaf3 ("V4L/DVB (5345): ivtv driver for Conexant cx23416/cx23415 MPEG encoder/decoder")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit dce47aed20c7de3ee2011b7a63e67f08e9dcfb5e ]

When updated IDs on f842c41a ("amlogic: meson-gx-socinfo: Update soc ids")
we introduced packages ids using the full 8bit value, but in the function
socinfo_to_package_id() the id was filtered with the 0xf0 mask.

While the 0xf0 mask is valid for most board, it filters out the lower
4 bits which encodes some characteristics of the chip.

This patch moves the mask into the meson_gx_package_id table to be applied
on each package name independently and add the correct mask for some
specific entries.

An example is the S905, in the vendor code the S905 is package_id
different from 0x20, and S905M is exactly 0x20.

Another example are the The Wetek Hub & Play2 boards using a S905-H
variant, which is the S905 SoC with some licence bits enabled.
These licence bits are encoded in the lower 4bits, so to detect
the -H variant, we must detect the id == 0x3 with the 0xf mask.

Fixes: f842c41a ("amlogic: meson-gx-socinfo: Update soc ids")
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit d1a6cbdf1e597917cb642c655512d91b71a35d22 ]

LP87565_BUCK_0 is missed, fix it.

Fixes: f0168a9b ("regulator: lp87565: Add support for lp87565 PMIC regulators")
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Reviewed-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 035a14e71f27eefa50087963b94cbdb3580d08bf ]

of_get_phy_mode may fail and return a negative error code;
the fix checks the return value of of_get_phy_mode and
returns NULL of it fails.

Fixes: b356e978 ("sh_eth: add device tree support")
Signed-off-by: NKangjie Lu <kjlu@umn.edu>
Reviewed-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Tested-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 201676095dda7e5b31a5e1d116d10fc22985075e ]

The "cpu" variable comes from the sscanf() so Smatch marks it as
untrusted data.  We can't pass a higher value than "nr_cpu_ids" to
cpu_possible() or it results in an out of bounds access.

Fixes: d68d82af ("xen: implement CPU hotplugging")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 5ac188b12e7cbdd92dee60877d1fac913fc1d074 ]

If riocm_get_channel() fails, then we should just return -EINVAL.
Calling riocm_put_channel() will trigger a NULL dereference and
generally we should call put() if the get() didn't succeed.

Link: http://lkml.kernel.org/r/20190110130230.GB27017@kadam
Fixes: b6e8d4aa ("rapidio: add RapidIO channelized messaging driver")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit eaab2d2d0fe4393b040dbf3922e18cd2ab7d6b85 ]

The simple vNIC mailbox length should be 12 decimal and not 0x12.
Using a decimal also makes it clear this is a length value and not
another field within the simple mailbox defines.

Found by code inspection, there are no known firmware configurations
where this would cause issues.

Fixes: 527d7d1b ("nfp: read mailbox address from TLV caps")
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 31b6a05f86e690e1818116fd23c3be915cc9d9ed ]

megaraid_sas takes 1+ seconds to load while waiting for firmware:

[2.822603] megaraid_sas 0000:03:00.0: Waiting for FW to come to ready state
[3.871003] megaraid_sas 0000:03:00.0: FW now in Ready state

This is due to the following loop in megasas_transition_to_ready(), which
waits a minimum of 1 second, even though the FW becomes ready in tens of
millisecs:

        /*
         * The cur_state should not last for more than max_wait secs
         */
        for (i = 0; i < max_wait; i++) {
                ...
                msleep(1000);
        ...
        dev_info(&instance->pdev->dev, "FW now in Ready state\n");

This is a regression, caused by a change of the msleep granularity from 1
to 1000 due to concern about waiting too long on systems with coarse
jiffies.

To fix, increase iterations and use msleep(20), which results in:

[2.670627] megaraid_sas 0000:03:00.0: Waiting for FW to come to ready state
[2.739386] megaraid_sas 0000:03:00.0: FW now in Ready state

Fixes: fb2f3e96d80f ("scsi: megaraid_sas: Fix msleep granularity")
Signed-off-by: NSteve Sistare <steven.sistare@oracle.com>
Acked-by: NSumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 3609e31bc8dc03b701390f79c74fc7fe92b95039 ]

The commit a2055abe ("x86/mm: Pass flush_tlb_info to
flush_tlb_others() etc") removed the unnecessary cpu parameter from
uv_flush_tlb_others() but left an unused variable.

arch/x86/mm/tlb.c: In function 'native_flush_tlb_others':
arch/x86/mm/tlb.c:688:16: warning: variable 'cpu' set but not used
[-Wunused-but-set-variable]
   unsigned int cpu;
                ^~~

Fixes: a2055abe ("x86/mm: Pass flush_tlb_info to flush_tlb_others() etc")
Signed-off-by: NQian Cai <cai@lca.pw>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NAndyt Lutomirski <luto@kernel.org>
Cc: dave.hansen@linux.intel.com
Cc: peterz@infradead.org
Cc: bp@alien8.de
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/20190228220155.88124-1-cai@lca.pwSigned-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 0f8ed994575429d6042cf5d7ef70081c94091587 ]

Building nios2:allmodconfig fails as follows (each symbol is only listed
once).

ERROR: "__ashldi3" [drivers/md/dm-writecache.ko] undefined!
ERROR: "__ashrdi3" [fs/xfs/xfs.ko] undefined!
ERROR: "__ucmpdi2" [drivers/media/i2c/adv7842.ko] undefined!
ERROR: "__lshrdi3" [drivers/md/dm-zoned.ko] undefined!
ERROR: "flush_icache_range" [drivers/misc/lkdtm/lkdtm.ko] undefined!
ERROR: "empty_zero_page" [drivers/md/dm-mod.ko] undefined!

The problem is seen with gcc 7.3.0.

Export the missing symbols.

Fixes: 2fc8483f ("nios2: Build infrastructure")
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 356889c49d84f11f446ec235bd52ca1a7d581aa0 ]

Otherwise the assert in rbd_obj_end_request() is triggered.

Fixes: 3da691bf ("rbd: new request handling code")
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 15d90a6ae98e6d2c68497b44a491cb9efbb98ab1 ]

earth-pt1 driver was decomposed/restructured by the commit b732539e
("media: dvb: earth-pt1: decompose pt1 driver into sub drivers"),
but it introduced a problem regarding concurrent streaming:
Opening a new terrestial stream stops the reception of an existing,
already-opened satellite stream.

The demod IC in earth-pt1 boards contains 2 pairs of terr. and sat. blocks,
supporting 4 concurrent demodulations, and the above problem was because
the config of a terr. block contained whole reset/init of the pair blocks,
thus each open() of a terrestrial frontend wrongly cleared the config of
its peer satellite block of the demod.
This whole/pair reset should be executed earlier and not on each open().

Fixes: b732539e ("media: dvb: earth-pt1: decompose pt1 driver into sub drivers")
Signed-off-by: NAkihiro Tsukada <tskd08@gmail.com>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 790845e2f12709d273d08ea7a2af7c2593689519 ]

We were always calling base_hpte_find() with primary = true,
even when we wanted to check the secondary table.

mpe: I broke this when refactoring Rashmica's original patch.

Fixes: 1515ab93 ("powerpc/mm: Dump hash table")
Signed-off-by: NRashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 8006e3730b6e900319411e35cee85b4513d298df ]

This is a real stack undercorruption found by kasan build.

The issue did no harm normally because it only overflowed
2 bytes after `bitary` array which on most architectures
were mapped into `err` local.

Fixes: bab6de8f ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.")
Signed-off-by: NNikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 108bb4afd351d65826648a47f11fa3104e250d9b ]

If the attempt to instantiate the mirror's layout DS pointer failed,
then that pointer may hold a value of type ERR_PTR(), so we need
to check that before we dereference it.

Fixes: 65990d1a ("pNFS/flexfiles: Fix a deadlock on LAYOUTGET")
Signed-off-by: NTrond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 1a3466aed3a17eed41cd9411f89eb637f58349b0 ]

These really should have been there from the beginning, but we never
noticed because there was enough slack in the RPC request for the extra
bytes. Chuck's recent patch to use au_cslack and au_rslack to compute
buffer size shrunk the buffer enough that this was now a problem for
SEEK operations on my test client.

Fixes: f4ac1674 ("nfs: Add ALLOCATE support")
Fixes: 2e72448b ("NFS: Add COPY nfs operation")
Fixes: cb95deea ("NFS OFFLOAD_CANCEL xdr")
Fixes: 624bd5b7 ("nfs: Add DEALLOCATE support")
Fixes: 1c6dcbe5 ("NFS: Implement SEEK")
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: NTrond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 984798de671a927ac73da31096a150df42e6aaf3 ]

BCM63XX (MIPS) does not use device tree, so there cannot be any
of_device_id, causing the driver to fail on probe:

[    0.904564] bcm2835-rng: probe of bcm63xx-rng failed with error -22

Fix this by checking for match data only if we are probing from device
tree.

Fixes: 8705f24f ("hwrng: bcm2835 - Enable BCM2835 RNG to work on BCM63xx platforms")
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit a01cbae57ec29b161d42ee1caa4ffffda5d519c2 ]

Use the element from the loop iteration, not the same element we want to
deactivate otherwise this branch always evaluates true.

Fixes: 6c03ae21 ("netfilter: nft_set_hash: add non-resizable hashtable implementation")
Reported-by: NFlorian Westphal <fw@strlen.de>
Tested-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 761156ff573d1002983416e4fd1fe8d3489c4bd8 ]

The length of wmi tlv command for management tx send is calculated
incorrectly in case of protected management frames as there is addition
of IEEE80211_CCMP_MIC_LEN twice. This leads to improper behaviour of
firmware as the wmi tlv mgmt tx send command for protected mgmt frames
is formed wrongly.

Fix the length calculation of wmi tlv command for mgmt tx send in case
of protected management frames by adding the IEEE80211_CCMP_MIC_LEN only
once.

Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1

Fixes: 1807da49 "ath10k: wmi: add management tx by reference support over wmi"
Signed-off-by: NSurabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>