The function wlc_phy_txpwrctrl_pwr_setup_nphy() does assign a local
variable target_pwr_qtrdbm in several code paths, but in the end all
code paths are coming to an assignment of that variable which does
override all previous. So those early and redundant assignments have
been removed.
Reported-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The radio initialization for 2057 rev 5 was using the incorrect
register table for the initialization. This patch fixes that.
Reported-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert printks to pr_<level>
Prefix logging with pr_fmt.
Use ##__VA_ARGS__ in some WL_ logging macros.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert a couple of pr_debug/print_hex_dump to
the standard utility.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use pr_debug to allow dynamic debugging to work.

Move an #endif to allow brcmf_dbg_hex_dump
to be outside the #if/#endif block.
Move a const char* declaration to be inside a
pr_debug so the function doesn't need a #if/#endif
block.
Don't use temporaries in debugging functions so
the code can be optimized away.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This doesn't do anything anymore.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reduce the number of #ifdef DEBUG uses by
adding a dbg_hex_dump routine which has the
appropriate #ifdef DEBUG test.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow dynamic debugging.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Current CONFIG_BRCMDBG flag when enabled does not
necessarily enable proper pr_debug output when
DEBUG is not also enabled.

Remove BCMDBG define and just use DEBUG instead.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All usage of ethtool_ops should be const; also add comma at end
of initializer list.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch workaround live deadlock problem caused by infinite loop
in brcms_c_wait_for_tx_completion(). I do not consider the patch as
the proper fix, which should fix the real reason of tx queue flush
failure, but patch helps with system lockup.

Reference:
https://bugzilla.kernel.org/show_bug.cgi?id=42576Reported-and-tested-by: NPatrick <ragamuffin@datacomm.ch>
Cc: stable@vger.kernel.org # 3.2+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Alexandre Oliva <oliva@lsd.ic.unicamp.br> says:

"It's an issue brought about by GCC 4.7's partial-inlining, that ends up
splitting the udelay function just at the wrong spot, in such a way that
some sanity checks for constants fails, and we end up calling
bad_udelay.

This patch fixes the problem.  Feel free to push it upstream if it makes
sense to you."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The brcmsmac driver isn't a PCI driver any more, it's a bcma one.  The
PCI device has been resumed by the PCI driver (the generic PCI layer,
really), we should be resuming just our own driver state.

Also add pr_debug() calls to show that we now actually get the
suspend/resume events.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now the low-level driver actually gets informed that it is getting suspended and resumed.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It appears that you can only read the sprom contents with aligned 16-bit
reads: anything else causes at least some versions of the broadcom
chipset to abort the PCI transaction, returning 0xff.

This apparently doesn't trigger very often, because most setups don't
use an external srom chip, and the OTP sprom loading doesn't have this
issue.  But at least the current 11" Macbook Air does trigger it, and
wireless communications were broken as a result.
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the memory allocation 'nvram_ularray = kmalloc(varsize,
GFP_ATOMIC);' fails we'll leak the memory allocated to 'vbuffer' when
we return -ENOMEM from the function.

This patch resolves the leak by kfree()'ing the allocated memory
before the return.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

DaveM said:
   Please, this kind of stuff rots forever and not using bool properly
   drives me crazy.

Joe Perches <joe@perches.com> gave me the spatch script:

	@@
	bool b;
	@@
	-b = 0
	+b = false
	@@
	bool b;
	@@
	-b = 1
	+b = true

I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a Kconfig option for SDIO bus support and abstracts
a build subset correspondingly. It's the final patch of fullmac bus
interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes some headers files include lines from sdio layer
code. This is part of the fullmac bus interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The idle macros are only used by dhd_sdio.c. It's more appropriate
to place them in dhd_sdio.c instead of dhd.h.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Debug message level macros are used for debug purpose. It would be
more appropriate to place them at dhd_dbg.h.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Abstract bus layer brcmf_bus_txctl/brcmf_bus_rxctl function
pointers for common layer. This patch is part of the fullmac bus
interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Abstract bus layer brcmf_bus_txdata function pointer for common
layer. This patch is part of the fullmac bus interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Abstract bus layer brcmf_bus_init function pointer for common
layer. This patch is part of the fullmac bus interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dhd_bus.h is the header file for bus interface. Move functions
declarations and brcmf_bus structure to there. This is part of
the fullmac bus interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Common layer should use interface function pointer stored in
brcmf_bus to invoke corresponding interface function in bus layer.
This patch is part of the fullmac bus interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dhd_bus.h will be used as the shared header file for common layer
and bus layer. It should not contain any sdio specific macros.
This patch moves them to sdio_host.h as part of the fullmac bus
interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmf_sdio is the data structure for sdio bus layer. Stop
referencing brcmf_sdio from common layer. This patch is part of
the fullmac bus interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmf_pub is the data structure for common layer. Since brcmf_bus
should be the only structure shared by common layer and bus layer,
stop referencing brcmf_pub from bus layer. This patch is part of
the fullmac bus interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

txoff is the flow control flag for transmit used in sdio layer.
Move it to bus layer data structure brcmf_sdio. Also flag
management code is moved out of brcmf_txflowcontrol(). This is
part of the fullmac bus interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

tx_realloc is used by both common layer and bus layer. This patch
moves it to interface structure brcmf_bus as part of the fullmac
bus interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Dongle statistics are shared data between common layer and bus
layer. This patch places them in bus interface structure brcmf_bus
as part of the fullmac bus interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some dongle statistics are stored in two places and synced when net
device status inquired. There is no need to do it this way any more.
Direct all usage to dongle stats structure in order to increase
readability.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver up/down status to network interface need to be shared by
common layer and bus layer. Move it to bus interface structure
brcmf_bus as part of the fullmac bus interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

maxctl is the max size of rxctl request from protocol layer to bus
layer. Move it to bus interface structure brcmf_bus. This is part
of the fullmac bus interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some statistics only used by sdio modules. Move them to sdio layer
private structure brcmf_sdio. This is part of the fullmac bus
interface refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change parameter to device pointer for bus layer interface function
brcmf_proto_hdrpull This is part of the fullmac bus interface
refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change parameter to device pointer for bus layer interface function
brcmf_rx_frame. This is part of the fullmac bus interface
refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change parameter to device pointer for bus layer interface function
brcmf_c_prec_enq. This is part of the fullmac bus interface
refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>