Added device tree support for omap musb driver and updated the
Documentation with device tree binding information.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The glue layer should directly write to mailbox register (present in
control module) instead of calling phy layer to write to mailbox
register. Writing to mailbox register notifies the core of events like
device connect/disconnect.

Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The mailbox register for usb otg in omap is present in control module.
On detection of any events VBUS or ID, this register should be written
to send the notification to musb core.

Till we have a separate control module driver to write to control module,
omap2430 will handle the register writes to control module by itself. So
a new address space to represent this control module register is added
to usb_otg_hs.
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some parameter names in this function's kernel-doc don't match the real
parameters. While at it, give the 'nIrq' parameter slightly more verbose
description.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Trivial patch fixin spelling of families in Kconfig

[ balbi@ti.com : added the obvious commit log ]
Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Variable ret is always evaluated as true, so we don't need to check it.
Signed-off-by: NMatthias Brugger <mbrugger@iseebcn.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When called during resume_irqs, omap2430_musb_set_vbus() is run with
interrupts disabled,  In that case 'jiffies' never changes so the loop
can loop forever.

So impose a maximum loop count and add an 'mdelay' to ensure we wait
a reasonable amount of time for bit to be cleared.

This fixes a hang on resume.
Signed-of-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

dma_controller_create is called only from musb_init_controller
which is __devint so annotate dma_controller_create also with
__devint.

fixes the warn

WARNING: vmlinux.o(.devinit.text+0x6fa8): Section mismatch in reference from the function musb_init_controller() to the function .init.text:dma_controller_create()
The function __devinit musb_init_controller() references
a function __init dma_controller_create().
If dma_controller_create is only used by musb_init_controller then
annotate dma_controller_create with a matching annotation.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Currently the errors returned by fifo_setup get masked
by EINVAL, propagate the same to the caller.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove unnecessary if condition. No change in logic.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

those two were defined to 1 anyway, quite useless.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

we are compiling the driver always with full OTG
capabilities, so that board_mode trick becomes
useless.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Do not rely on any hints from gadget drivers and use DMA mode 1
whenever we expect data of at least the endpoint's packet size and
have not yet received a short packet.

The last packet if short is always transferred using DMA mode 0.

This patch fixes USB throughput issues in mass storage mode for
host to device transfers.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case of USB bulk transfer, when himem page
is received, the usb_sg_init function sets the
urb transfer buffer to NULL. When such URB
transfer is handled, kernel crashes in PIO mode.
Handle this by mapping the highmem buffer in PIO mode.
Signed-off-by: NVirupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: NPraveena NADAHALLY <praveen.nadahally@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Commit 62285963 (usb: musb: drop a
gigantic amount of ifdeferry) included this change:

    @@ -1901,11 +1844,7 @@ static void musb_free(struct musb *musb)
                    dma_controller_destroy(c);
            }

    -#ifdef CONFIG_USB_MUSB_HDRC_HCD
    -       usb_put_hcd(musb_to_hcd(musb));
    -#else
            kfree(musb);
    -#endif
     }

     /*

Since musb comes from struct usb_hcd's hcd_priv, which is allocated on
the end of that struct, kfree'ing it is not going to work.  Replace
kfree(musb) with usb_put_hcd(musb_to_hcd(musb)), which appears to be
the right thing to do here.
Signed-off-by: NBrian Downing <bdowning@lavos.net>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The following warnings are fixed:

drivers/usb/musb/musb_core.c:357:6: warning: symbol 'musb_otg_timer_func' was not declared. Should it be static?
drivers/usb/musb/musb_core.c:1339:27: warning: incorrect type in initializer (different address spaces)
drivers/usb/musb/musb_core.c:1339:27:    expected void *mbase
drivers/usb/musb/musb_core.c:1339:27:    got void [noderef] <asn:2>*mregs
drivers/usb/musb/musb_core.c:1347:17: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/musb/musb_core.c:1347:17:    expected void [noderef] <asn:2>*addr
drivers/usb/musb/musb_core.c:1347:17:    got void *mbase
drivers/usb/musb/musb_core.h:487:27: warning: incorrect type in initializer (different address spaces)
drivers/usb/musb/musb_core.h:487:27:    expected void *mbase
drivers/usb/musb/musb_core.h:487:27:    got void [noderef] <asn:2>*mregs
drivers/usb/musb/musb_core.h:491:26: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/musb/musb_core.h:491:26:    expected void const [noderef] <asn:2>*addr
drivers/usb/musb/musb_core.h:491:26:    got void *mbase
drivers/usb/musb/tusb6010.c:270:48: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/musb/tusb6010.c:270:48:    expected void [noderef] <asn:2>*buf
drivers/usb/musb/tusb6010.c:270:48:    got unsigned char [usertype] *[assigned] buf
drivers/usb/musb/tusb6010.c:164:32: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/musb/tusb6010.c:164:32:    expected void *to
drivers/usb/musb/tusb6010.c:164:32:    got void [noderef] <asn:2>*buf
drivers/usb/musb/tusb6010.c:172:24: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/musb/tusb6010.c:172:24:    expected void *to
drivers/usb/musb/tusb6010.c:172:24:    got void [noderef] <asn:2>*[assigned] buf
Signed-off-by: NFelipe Balbi <balbi@ti.com>

No functional change. Just replaced the call to platform_device_del and
platform_device_put with platform_device_unregister.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fixes endpoint starvation issue when more than one bulk QH is
multiplexed on the reserved bulk TX endpoint.

This patch sets the NAK timeout interval for such QHs, and when
a timeout triggers the next QH will be scheduled.

This scheme doesn't work for devices which are connected to a
high to full speed tree (transaction translator) as there is
no NAK timeout interrupt from the musb controller from such
devices.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Added a check in musb_{read | write}_fifo for zero byte length.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This is to reduce the overhead of dma programming for zero byte
transmit as same can be done using pio mode.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This is to reduce the overhead of dma programming for zero byte
transmit as same can be done using pio mode.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In rxstate(), improper types are given to 'fifo_count' and 'len' variables, and
these variables are not used in accordance to their names (up to the certain
point), i.e. 'len' to hold the size of a packet in the RX FIFO, and 'fifo_count'
to hold a difference between 'request->length' and 'request->actual'...
Interchange the variables up to the point where their use starts to make sense
again.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Pull OLPC platform updates from Andres Salomon:
 "These move the OLPC Embedded Controller driver out of
  arch/x86/platform and into drivers/platform/olpc.

  OLPC machines are now ARM-based (which means lots of x86 and ARM
  changes), but are typically pretty self-contained..  so it makes more
  sense to go through a separate OLPC tree after getting the appropriate
  review/ACKs."

* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
  x86: OLPC: move s/r-related EC cmds to EC driver
  Platform: OLPC: move global variables into priv struct
  Platform: OLPC: move debugfs support from x86 EC driver
  x86: OLPC: switch over to using new EC driver on x86
  Platform: OLPC: add a suspended flag to the EC driver
  Platform: OLPC: turn EC driver into a platform_driver
  Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
  drivers: OLPC: update various drivers to include olpc-ec.h
  Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver

Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
 "This contains a set of device-tree conversions for Marvell Orion
  platforms that were staged early but took a few tries to get the
  branch into a format where it was suitable for us to pick up.

  Given that most people working on these platforms are hobbyists with
  limited time, we were a bit more flexible with merging it even though
  it came in late."

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
  ARM: Kirkwood: Replace mrvl with marvell
  ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
  ARM: Kirkwood: Describe Dreamplug LEDs in DT.
  ARM: Kirkwood: Describe iConnects LEDs in DT.
  ARM: Kirkwood: Describe iConnects temperature sensor in DT.
  ARM: Kirkwood: Describe IB62x0 LEDs in DT.
  ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
  ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
  ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
  ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
  ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
  ARM: Kirkwood: Use DT to configure SATA device.
  ARM: kirkwood: use devicetree for SPI on dreamplug
  ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
  ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
  ARM: Kirkwood: Add basic device tree support for QNAP TS219.
  ATA: sata_mv: Add device tree support
  ARM: Orion: DTify the watchdog timer.
  ARM: Orion: Add arch support needed for I2C via DT.
  ARM: kirkwood: use devicetree for orion-spi
  ...

Conflicts:
	drivers/watchdog/orion_wdt.c

Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
 "Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
  but didn't go in because the pull request ended up rejected.  So it
  just got merged, and we got this staged branch that enables the
  coupled cpuidle code on OMAP.

  With a stable git workflow from the other maintainer we could have
  staged this earlier, but that wasn't the case so we have had to merge
  it late.

  The alternative is to hold it off until 3.7 but given that the code is
  well-isolated to OMAP and they are eager to see it go in, I didn't
  push back hard in that direction."

* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP4: CPUidle: Open broadcast clock-event device.
  ARM: OMAP4: CPUidle: add synchronization for coupled idle states
  ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
  ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes for merge window fallout, and a bugfix for timer resume on
  PRIMA2."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: mmp: add missing irqs.h
  arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
  ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
  ARM: mxc: Include missing irqs.h header

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
  sh: explicitly include sh_dma.h in setup-sh7722.c
  sh: ecovec: care CN5 VBUS if USB host mode
  sh: sh7724: fixup renesas_usbhs clock settings
  sh: intc: initial irqdomain support.
  sh: pfc: Fix up init ordering mess.
  serial: sh-sci: fix compilation breakage, when DMA is enabled
  dmaengine: shdma: restore partial transfer calculation
  sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
  sh: Fix up recursive fault in oops with unset TTB.
  sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
  sh: select the fixed regulator driver on several boards
  sh: ecovec: switch MMC power control to regulators
  sh: add fixed voltage regulators to se7724
  sh: add fixed voltage regulators to sdk7786
  sh: add fixed voltage regulators to rsk
  sh: add fixed voltage regulators to migor
  sh: add fixed voltage regulators to kfr2r09
  sh: add fixed voltage regulators to ap325rxa
  sh: add fixed voltage regulators to sh7757lcr
  sh: add fixed voltage regulators to sh2007
  ...

Pull additional md update from NeilBrown:
 "This contains a few patches that depend on plugging changes in the
  block layer so needed to wait for those.

  It also contains a Kconfig fix for the new RAID10 support in dm-raid."

* tag 'md-3.6' of git://neil.brown.name/md:
  md/dm-raid: DM_RAID should select MD_RAID10
  md/raid1: submit IO from originating thread instead of md thread.
  raid5: raid5d handle stripe in batch way
  raid5: make_request use batch stripe release

Pull two ceph fixes from Sage Weil:
 "The first patch fixes up the old crufty open intent code to use the
  atomic_open stuff properly, and the second fixes a possible null deref
  and memory leak with the crypto keys."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: fix crypto key null deref, memory leak
  ceph: simplify+fix atomic_open

Merge tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull ecryptfs fixes from Tyler Hicks:
 - Fixes a bug when the lower filesystem mount options include 'acl',
   but the eCryptfs mount options do not
 - Cleanups in the messaging code
 - Better handling of empty files in the lower filesystem to improve
   usability.  Failed file creations are now cleaned up and empty lower
   files are converted into eCryptfs during open().
 - The write-through cache changes are being reverted due to bugs that
   are not easy to fix.  Stability outweighs the performance
   enhancements here.
 - Improvement to the mount code to catch unsupported ciphers specified
   in the mount options

* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: check for eCryptfs cipher support at mount
  eCryptfs: Revert to a writethrough cache model
  eCryptfs: Initialize empty lower files when opening them
  eCryptfs: Unlink lower inode when ecryptfs_create() fails
  eCryptfs: Make all miscdev functions use daemon ptr in file private_data
  eCryptfs: Remove unused messaging declarations and function
  eCryptfs: Copy up POSIX ACL and read-only flags from lower mount

Pull CIFS update from Steve French:
 "Adds SMB2 rmdir/mkdir capability to the SMB2/SMB2.1 support in cifs.

  I am holding up a few more days on merging the remainder of the
  SMB2/SMB2.1 enablement although it is nearing review completion, in
  order to address some review comments from Jeff Layton on a few of the
  subsequent SMB2 patches, and also to debug an unrelated cifs problem
  that Pavel discovered."

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Add SMB2 support for rmdir
  CIFS: Move rmdir code to ops struct
  CIFS: Add SMB2 support for mkdir operation
  CIFS: Separate protocol specific part from mkdir
  CIFS: Simplify cifs_mkdir call

Borislav Petkov reports that the new warning added in commit
88fdf75d ("mm: warn if pg_data_t isn't initialized with zero")
triggers for him, and it is the node_start_pfn field that has already
been initialized once.

The call trace looks like this:

  x86_64_start_kernel ->
    x86_64_start_reservations ->
    start_kernel ->
    setup_arch ->
    paging_init ->
    zone_sizes_init ->
    free_area_init_nodes ->
    free_area_init_node

and (with the warning replaced by debug output), Borislav sees

  On node 0 totalpages: 4193848
    DMA zone: 64 pages used for memmap
    DMA zone: 6 pages reserved
    DMA zone: 3890 pages, LIFO batch:0
    DMA32 zone: 16320 pages used for memmap
    DMA32 zone: 798464 pages, LIFO batch:31
    Normal zone: 52736 pages used for memmap
    Normal zone: 3322368 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 4423680      <----
  On node 1 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 8617984      <----
  On node 2 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 12812288     <----
  On node 3 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31

so remove the bogus warning for now to avoid annoying people.  Minchan
Kim is looking at it.
Reported-by: NBorislav Petkov <bp@amd64.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

arch/arm/mach-mmp/gplugd.c:195:13: error: ‘MMP_NR_IRQS’ undeclared here
(not in a function)
make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1

Include <mach/irqs.h> to fix this issue.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The comment was wrongly referring to Armada 370 while the file is
related to Armada XP.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The only way to write LATCHED registers to write LATCH_BIT to LATCH register,
that will latch COUNTER into LATCHED.e.g.
writel_relaxed(SIRFSOC_TIMER_LATCH_BIT, sirfsoc_timer_base +
	SIRFSOC_TIMER_LATCH);

Writing values to LATCHED registers directly is useless at all.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Avoid crashing if the crypto key payload was NULL, as when it was not correctly
allocated and initialized.  Also, avoid leaking it.
Signed-off-by: NSylvain Munaut <tnt@246tNt.com>
Signed-off-by: NSage Weil <sage@inktank.com>
Reviewed-by: NAlex Elder <elder@inktank.com>

The initial ->atomic_open op was carried over from the old intent code,
which was incomplete and didn't really work.  Replace it with a fresh
method.  In particular:

 * always attempt to do an atomic open+lookup, both for the create case
   and for lookups of existing files.
 * fix symlink handling by returning 1 to the VFS so that we can follow
   the link to its destination. This fixes a longstanding ceph bug (#2392).
Signed-off-by: NSage Weil <sage@inktank.com>

setup-sh7722.c defines several objects, whose types are defined in
sh_dma.h, so, it has to be included explicitly.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Pull MIPS updates from Ralf Baechle:
 "The lion share of this pull request are fixes for clk-related breakage
  caused by other changes during this merge window.  For some platforms
  the fix was as simple as selecting HAVE_CLK, for others like the
  Loongson 2 significant restructuring was required.

  The remainder are changes required to get the Lantiq code to work
  again."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Loongson 2: Sort out clock managment.
  MIPS: Loongson 1: more clk support and add select HAVE_CLK
  MIPS: txx9: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: BCM63xx: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: AR7: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: Lantiq: Platform specific CLK fixup
  MIPS: Lantiq: Add device_tree_init function
  MIPS: Lantiq: Fix interface clock and PCI control register offset