A randconfig build hit the following build errors because xhci.c and
xhci-mem.c use dma mapping functions but don't include
<linux/dma-mapping.h>. Add the missing includes to fix the build errors.

drivers/usb/host/xhci.c In function 'xhci_gen_setup':
drivers/usb/host/xhci.c +4872 : error: implicit declaration of function 'dma_set_mask'
drivers/usb/host/xhci.c +4872 : error: implicit declaration of function 'DMA_BIT_MASK'

drivers/usb/host/xhci-mem.c In function 'xhci_free_stream_ctx':
drivers/usb/host/xhci-mem.c +435 : error: implicit declaration of function 'dma_free_coherent'
drivers/usb/host/xhci-mem.c In function 'xhci_alloc_stream_ctx':
drivers/usb/host/xhci-mem.c +463 : error: implicit declaration of function 'dma_alloc_coherent'
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

in some cases where device is attched to xhci port and do not responding,
for example ath9k_htc with stalled firmware, kernel will
crash on ring_doorbell_for_active_rings.
This patch check if pointer exist before it is used.

This patch should be backported to kernels as old as 2.6.35, that
contain the commit e9df17eb "USB: xhci:
Correct assumptions about number of rings per endpoint"
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Xhci controllers with hci_version > 0.96 gives spurious success
events on short packet completion. During webcam capture the
"ERROR Transfer event TRB DMA ptr not part of current TD" was observed.
The same application works fine with synopsis controllers hci_version 0.96.
The same issue is seen with Intel Pantherpoint xhci controller. So enabling
this quirk in xhci_gen_setup if controller verion is greater than 0.96.
For xhci-pci move the quirk to much generic place xhci_gen_setup.

Note from Sarah:

The xHCI 1.0 spec changed how hardware handles short packets.  The HW
will notify SW of the TRB where the short packet occurred, and it will
also give a successful status for the last TRB in a TD (the one with the
IOC flag set).  On the second successful status, that warning will be
triggered in the driver.

Software is now supposed to not assume the TD is not completed until it
gets that last successful status.  That means we have a slight race
condition, although it should have little practical impact.  This patch
papers over that issue.

It's on my long-term to-do list to fix this race condition, but it is a
much more involved patch that will probably be too big for stable.  This
patch is needed for stable to avoid serious log spam.

This patch should be backported to kernels as old as 3.0, that
contain the commit ad808333 "Intel xhci:
Ignore spurious successful event."

The patch will have to be modified for kernels older than 3.2, since
that kernel added the xhci_gen_setup function for xhci platform devices.
The correct conflict resolution for kernels older than 3.2 is to set
XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Fix warning when CONFIG_PCI is not enabled
(from commit 29636578).

drivers/usb/host/pci-quirks.h: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Resolves the following build warnings:
drivers/usb/host/xhci.c:332:13: warning: 'xhci_msix_sync_irqs' defined but not used [-Wunused-function]
drivers/usb/host/xhci.c:3901:12: warning: 'xhci_change_max_exit_latency' defined but not used [-Wunused-function]

These functions are not always used, and since they're marked static
they will produce build warnings:
- xhci_msix_sync_irqs is only used with CONFIG_PCI.
- xhci_change_max_exit_latency is a little more complicated with
  dependencies on CONFIG_PM and CONFIG_PM_RUNTIME.

Instead of building a bigger maze of ifdefs in this code, I've just
marked both with __maybe_unused.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

When the host controller fails to respond to an Enable Slot command, and
the host fails to respond to the register write to abort the command
ring, the xHCI driver will assume the host is dead, and call
usb_hc_died().

The USB device's slot_id is still set to zero, and the pointer stored at
xhci->devs[0] will always be NULL.  The call to xhci_check_args in
xhci_free_dev should have caught the NULL virt_dev pointer.

However, xhci_free_dev is designed to free the xhci_virt_device
structures, even if the host is dead, so that we don't leak kernel
memory.  xhci_free_dev checks the return value from the generic
xhci_check_args function.  If the return value is -ENODEV, it carries on
trying to free the virtual device.

The issue is that xhci_check_args looks at the host controller state
before it looks at the xhci_virt_device pointer.  It will return -ENIVAL
because the host is dead, and xhci_free_dev will ignore the return
value, and happily dereference the NULL xhci_virt_device pointer.

The fix is to make sure that xhci_check_args checks the xhci_virt_device
pointer before it checks the host state.

See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for
further details.  This patch doesn't solve the underlying issue, but
will ensure we don't see any more NULL pointer dereferences because of
the issue.

This patch should be backported to kernels as old as 3.1, that
contain the commit 7bd89b40 "xhci: Don't
submit commands or URBs to halted hosts."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NVincent Thiele <vincentthiele@gmail.com>
Cc: stable@vger.kernel.org

Set the ehci->resuming flag for the port we receive a remote
wakeup on so that resume signalling can be completed.

Without this, the root hub timer will not fire again to check
if the resume was completed and there will be a never-ending wait on
on the port.

This effect is only observed if the HUB IRQ IN does not come after we
have initiated the port resume.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds missing unlocks on error paths in the
xhci_free_streams and xhci_configure_endpoint functions.
Signed-off-by: NEmil Goode <emilgoode@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a race condition that caused the HWA_HC interface probe
function to occasionally fail.  The HWA_HC would attempt to register
itself with the HWA_RC by searching for a uwb_rc class device with the
same parent device ptr.  If the probe function for the HWA_RC interface
had yet to run, the uwb_rc class device would not have been created
causing the look up to fail and the HWA_HC probe function to return an
error causing the device to be unusable.

The fix is for the HWA to delay registering with the HWA_RC until
receiving the command from userspace to start the wireless channel.  It
is the responsibility of userspace to ensure that the uwb_rc class
device has been created before starting the HWA channel.
Signed-off-by: NThomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Do a release_mem_region of the hcd resource. Without this the
subsequent insertion of module fails in request_mem_region.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.4+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fail and free the container context in case dma_pool_alloc() can't allocate
the raw context data part of it

This patch should be backported to kernels as old as 2.6.31, that
contain the commit d115b048 "USB: xhci:
Support for 64-byte contexts".
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ARCH_EXYNOS is going to be excluded from PLAT_S5P, so it must be checked
separately in Exynos-related Kconfig entries.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch removes a double assignment of .start in struct hc_driver
ehci_msp_hc_driver and also makes the code look more tidy.
Signed-off-by: NEmil Goode <emilgoode@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For PHY mode, the PHYs must be brought out of reset
before the EHCI controller is started.

This patch fixes the issue where USB devices are not found
on Beagleboard/Beagle-xm if USB has been started previously
by the bootloader. (e.g. by "usb start" command in u-boot)

Tested on Beagleboard, Beagleboard-xm and Pandaboard.

Issue present on 3.10 onwards.
Reported-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.10
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Under some circumstances it happens that the connected PHY can't be
powered up properly, in which case the cleanup path currently crashes
because it checks the tegra->transceiver field using !IS_ERR(), which
will succeed because it is in fact NULL. Dereferencing that pointer
causes an oops in tegra_ehci_probe().

This patch fixes the issue by adding an additional label into the
cleanup path to separately take down the PHY and the transceiver.
Signed-off-by: NThierry Reding <thierry.reding@gmail.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Rather than allocating struct tegra_ehci_hcd separately, use struct
ehci_hcd's priv field instead.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Separate the Tegra on-chip host controller driver from
ehci-hcd host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: NManjunath Goudar <manjunath.goudar@linaro.org>
[swarren, reworked Manjunath's patches to split them more logically,
minor re-order of added lines to better match layout of other split-up
HCD drivers and existing code, add MODULE_DEVICE_TABLE, fix
MODULE_LICENSE, adapted to change in earlier patches which removed the
ehci_driver_overrides addition, removed all PM code and solved circular
dependencies.]
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Tegra EHCI driver directly calls various functions in the Tegra USB
PHY driver. The reverse is also true; the PHY driver calls into the EHCI
driver. This is problematic when the two are built as modules.

The calls from the PHY to EHCI driver were originally added in commit
bbdabdb6 "usb: add APIs to access host registers from Tegra PHY", for the
following reasons:

1) The register being touched is an EHCI register, so logically only the
   EHCI driver should touch it.
2) (1) implies that some locking may be needed to correctly implement the
   r/m/w access to this shared register.
3) We were expecting to pass only the PHY register space to the Tegra PHY
   driver, and hence it would not have access to touch the shared
   registers.

To solve this, that commit added functions in the EHCI driver to touch the
shared register on behalf of the PHY driver.

In practice, we ended up not having any locking in the implementaiton of
those functions, and I've been led to believe this is safe. Equally, (3)
did not happen either. Hence, it is possible for the PHY driver to touch
the shared register directly.

Given that, this patch moves the code to touch the shared register back
into the PHY driver, to eliminate the module problems. If we actually
need locking or co-ordination in the future, I propose we put the lock
support into some pre-existing core module, or into a third separate
module, in order to avoid the circular dependencies.

I apologize for my contribution to code churn here.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The PM routines in ehci-tegra.c use APIs such as ehci_reset(),
ehci_halt(), and ehci_tdi_reset() that would need to be exported to
convert ehci-tegra.c into a separate module from ehci-hcd.c. However,
we'd prefer not to export them.

Instead, simply remove all power management functionality. Runtime PM
was disabled since it didn't work correctly, and system suspend isn't
yet supported in a meaningful way. So, this change doesn't lose any
functionality.

Hopefully the power management logic can be reimplemented in a cleaner
way in the future.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In order to split ehci-hcd.c into separate modules, handshake() must be
exported. Rename the symbol to add an ehci_ prefix, to avoid any naming
clashes.
Signed-off-by: NManjunath Goudar <manjunath.goudar@linaro.org>
[swarren, split Manjunath's patches more logically, limit this change
to export just handshake()]
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support for scatter gather DMA to the wire adapter and
updates the HWA to advertise support for SG transfers.  This allows the
block layer to submit transfer requests to the HWA HC without first
breaking them up into PAGE_SIZE requests.
Signed-off-by: NThomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the endpoint type is unknown, set it to 0 and fail gracefully
instead of causing a kernel panic.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

We may have more speed types in the future, so fail gracefully, rather
than causing the kernel to panic.

BUG() was called if the device speed was unknown when setting max packet
size.  Set the max packet size at the same time as the slot speed and
get rid of one switch statement with BUG() option completely.

[Note: Sarah merged a patch that she wrote that touched the
xhci_setup_addressable_virt_dev function with this patch from Mathias
for clarity.]
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Fail gracefully, instead of causing the kernel to panic, if the input
control context doesn't have the right type (XHCI_CTX_TYPE_INPUT).  Push
finding the pointer to the input control context up into functions that
can fail.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>

It's horrible coding style to panic the kernel when someone passes you
an argument value you didn't expect.  In the future, we may want to add
additional context types, so it's better to gracefully handle additional
context types instead of panicking.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>

Sometimes there is a need  to initialize some non-standard registers mapped to
the EHCI region before accessing the standard EHCI registers.  Add pre_setup()
method with 'struct usb_hcd *' parameter to be called just before ehci_setup()
to the 'ehci-platform'  driver's platform data for this purpose...

While at it, add the missing incomplete declaration of 'struct platform_device'
to <linux/usb/ehci_pdriver.h>...

The patch has been tested on the Marzen and BOCK-W boards.
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

CAVIUM_OCTEON_SOC most place we used to use CPU_CAVIUM_OCTEON.  This
allows us to CPU_CAVIUM_OCTEON in places where we have no OCTEON SOC.

Remove CAVIUM_OCTEON_SIMULATOR as it doesn't really do anything, we can
get the same configuration with CAVIUM_OCTEON_SOC.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-edac@vger.kernel.org
Cc: linux-i2c@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: spi-devel-general@lists.sourceforge.net
Cc: devel@driverdev.osuosl.org
Cc: linux-usb@vger.kernel.org
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Patchwork: https://patchwork.linux-mips.org/patch/5295/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Suspend and resume are not currently supported on the wireless root hub.
Remove the suspend and resume op functions in the host controller driver
to avoid constant error messages in the system log.
Signed-off-by: NThomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The three options USB_ARCH_HAS_{EHCI,OHCI,XHCI} are all well beyond
their recommended shelf life. They have caused numerous build failures
over the years because they are never completely correct, and with
the move to splitting out the platform specific back-ends out of the
driver, there is no real need for them any more. Also, the use of making
USB_ARCH_HAS_HCD depend on it is questionable since one can always enable
dummy_hc these days.

This patch enables them unconditionally for all platforms and
architectures, which means it is now possible to build host controller
drivers for machines that are known not to come with this hardware,
but that is just how we treat most other drivers.

In order to minimise the impact on existing architecture code and
defconfig files, all the Kconfig are left present for now. All platforms
that currently do 'select USB_ARCH_HAS_*' should subsequently be changed
not to select that. All drivers depending on USB_ARCH_HAS_HCD should
be changed to depend on USB_SUPPORT instead.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The OHCI host controller driver can be built standalone now,
without enabling any of the available bus glue drivers, so
there is not really a reason to error out here:

drivers/usb/host/ohci-hcd.c:1258: error:
 #error "missing bus glue for ohci-hcd"  #error "missing bus glue for ohci-hcd"

This follows the same change done in ehci recently as 843e56c0
"USB: EHCI: remove bogus #error" and hopefully avoids future
merge conflicts in this list.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adds abitilty to tune L1 timeout (inactivity timer for usb2 link sleep)
and BESL (best effort service latency)via sysfs.

This also adds a new usb2_lpm_parameters structure with those variables to
struct usb_device.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

usb 2.0 devices with link power managment (LPM) can describe their idle link
timeouts either in BESL or HIRD format, so far xHCI has only supported HIRD but
later xHCI errata add BESL support as well

BESL timeouts need to inform exit latency changes with an evaluate
context command the same way USB 3.0 link PM code does.
The same xhci_change_max_exit_latency() function is used as with USB3
but code is pulled out from #ifdef CONFIG_PM as USB2.0 BESL LPM
funcionality does not depend on CONFIG_PM.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Hardware link powermanagement in usb2 is a per-port capability.
Previously support for hw lpm was enabled for all ports if any usb2 port supported it.

Now instead cache the capability values and check them for each port individually
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

According to Felipe and Alan's comments the second parameter of irq
handler should be 'void *' not a specific structure pointer.
So change it.
Signed-off-by: NAlex Shi <alex.shi@intel.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

When CONFIG_XHCI_HCD_DEBUGGING is activated, the XHCI driver can dump
device and input contexts to the console. The endpoint contexts in that
dump are labeled "Endpoint N Context", where N is the XHCI endpoint
index (DCI - 1). This can be very confusing, especially for people who
are not that familiar with the XHCI specification. This patch introduces
an xhci_get_endpoint_address function (as a counterpart to the reverse
xhci_get_endpoint_index), and uses it to additionally display the
endpoint number and direction when dumping contexts, which are much more
commonly used concepts in USB.
Signed-off-by: NJulius Werner <jwerner@chromium.org>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

This patch adds an ohci->priv field for private use by OHCI
platform drivers.

Until now none of the platform drivers has used this private space,
but that's about to change in the next patch of this series.
Signed-off-by: NManjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch splits the ohci-platform code from ohci-hcd out
into its own separate driver module.This work is part of enabling
multi-platform kernels on ARM.

In V2:
  -Passed "hcd" argument instead of "ohci" in ohci_setup() because it is
   using "struct usb_hcd" argument.
In V3:
  -Directly passed "hcd" argument not required to call ohci_to_hcd() function.
Signed-off-by: NManjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>