Current code for offloading IP-in-IP tunneling assumes that there is no
decap without encap. But that's never true for IPv6 overlays, and is not
true for IPv4 ones either, if net.ipv4.conf.*.rp_filter is unset.

To support decap-only tunnels, an IPIP entry is now created as soon as
an offloadable tunneling device is created. When that netdevice is up'd,
a decap route is looked up and possibly offloaded. Thus decap is not
handled implicitly as part of mlxsw_sp_ipip_entry_get() call anymore,
but needs to be done explicitly after the get, if desired.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far, all netdevice notifications that the driver cared about were
related to its own ports, and mlxsw_sp could be retrieved from the
netdevice's private data. For IP-in-IP offloading however, the driver
cares about events on foreign netdevices, and getting at mlxsw_sp or
router data structures from the handler is inconvenient.

Therefore move the netdevice notifier blocks from global scope to struct
mlxsw_sp to allow retrieval from the notifier block pointer itself.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code that actually takes care of bridge offload introduces a few
more non-trivial constraints with regards to bridge enslavements.
Propagate extack there to indicate the reason.

$ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10
$ ip link add link enp1s0np1 name enp1s0np1.20 type vlan id 20
$ ip link add name br0 type bridge
$ ip link set dev enp1s0np1.10 master br0
$ ip link set dev enp1s0np1.20 master br0
Error: spectrum: Can not bridge VLAN uppers of the same port.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the multicast routing hardware API introduced in previous patch
for the specific spectrum hardware.

The spectrum hardware multicast routes are written using the RMFT2 register
and point to an ACL flexible action set. The actions used for multicast
routes are:
 - Counter action, which allows counting bytes and packets on multicast
   routes.
 - Multicast route action, which provide RPF check and do the actual packet
   duplication to a list of RIFs.
 - Trap action, in the case the route action specified by the called is
   trap.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the multicast router offloading logic, which is in charge of handling
the VIF and MFC notifications and translating it to the hardware logic API.

The offloading logic has to overcome several obstacles in order to safely
comply with the kernel multicast router user API:
 - It must keep track of the mapping between VIFs to netdevices. The user
   can add an MFC cache entry pointing to a VIF, delete the VIF and add
   re-add it with a different netdevice. The offloading logic has to handle
   this in order to be compatible with the kernel logic.
 - It must keep track of the mapping between netdevices to spectrum RIFs,
   as the current hardware implementation assume having a RIF for every
   port in a multicast router.
 - It must handle routes pointing to pimreg device to be trapped to the
   kernel, as the packet should be delivered to userspace.
 - It must handle routes pointing tunnel VIFs. The current implementation
   does not support multicast forwarding to tunnels, thus routes that point
   to a tunnel should be trapped to the kernel.
 - It must be aware of proxy multicast routes, which include both (*,*)
   routes and duplicate routes. Currently proxy routes are not offloaded
   and trigger the abort mechanism: removal of all routes from hardware and
   triggering the traffic to go through the kernel.

The multicast routing offloading logic also updates the counters of the
offloaded MFC routes in a periodic work.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate error instead of doing WARN_ON right away.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Attach mid getting and releasing mid id to the HW write / remove, and add
a flag to indicate whether the mid is in the HW. It is done because mid id
is also HW index to this mid.
This change allows adding in the following patches the ability to have a
mid in the mdb cache but not in the HW. It will be useful for being able
to disable the multicast.
It means that the mdb is being written / delete to the HW in the mid
allocation / removing function, not after them.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since there is a bitmap for the ports registered to each mid, there is no
need for a ref count, since it will always be the number of set bits in
this bitmap. Any check of the ref count was replaced with checking if the
bitmap is empty.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a bitmap of ports to the mid struct to hold the ports that are
registered to this mid.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A flexible action instance allows, given a set of ops, creating, committing
and sharing a set of ACL action blocks. The flexible action instance in
question is using the spectrum KVD linear space to store the flexible
action sets.

Move this flexible action instance to the common spectrum struct to allow
other users (such as multicast router) to get that functionality.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When offloading L3 tunnels, an adjacency entry is created that loops the
packet back into the underlay router. Loopback interfaces then hold the
corresponding information and are created for IP-in-IP netdevices.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to lookup ruleset in order to offload goto_chain termination
action. This patch adds it.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For goto_chain action we need to know group_id of a ruleset to jump to.
Provide infrastructure in order to get it.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reflect chain index coming down from TC core and create a ruleset per
chain. Note that only chain 0, being the implicit chain, is bound to the
device for processing. The rest of chains have to be "jumped-to" by
actions.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a netdev is configured with an IP address a router interface (RIF)
should be configured for it in the device. Allow configuration of RIFs
based on IPv6 address notifications as well as IPv4.

Note that the RIF exists as long as an IP address is configured on the
netdev, regardless of the address family.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for learning FDB through notification. The driver defers
the hardware update via ordered work queue. Support for stacked devices
is also provided. In case of a successful FDB add a notification is
sent back to bridge.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use trap/discard flex action to implement trap.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make it clear where functions are defined and move misplaced declaration
to their correct place.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlxsw driver currently implements three types of RIFs. VLAN and FID
RIFs for L3 interfaces on top of VLAN-aware and VLAN-unaware bridges
(respectively) and Subport RIFs for all other L3 interfaces.

All the RIF types follow a common configuration procedure, which only
differs in the type-specific bits. The patch exploits this fact and
consolidates the common code paths, thereby simplifying the code and
making it more extensible.

This work also prepares the driver for use with future ASICs, where the
range of the Subport RIFs will be extended and their configuration
modified accordingly. By merely implementing a new RIF operations and
selecting it during initialization, the same driver could be re-used.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device supports three types of FIDs. 802.1Q and 802.1D FIDs for
VLAN-aware and VLAN-unaware bridges (respectively) and rFIDs to
transport packets to the router block.

The different users (e.g., bridge, router, ACLs) of the FIDs
infrastructure need not know about the internal FIDs implementation and
can therefore interact with it using a restricted set of exported
functions.

By encapsulating the entire FID logic and hiding it from the rest of the
driver we get a code base that it much simpler and easier to work with
and extend.

For example, in the current Spectrum ASIC only 802.1D FIDs can be
assigned a VNI, but future ASICs will also support 802.1Q FIDs. With
this patch in place, support for future ASICs can be easily added by
implementing a new FID operations according to their capabilities.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As explained in the cover letter, since the introduction of the bridge
offload in the mlxsw driver, information related to the offloaded bridge
and bridge ports was stored in the individual port struct,
mlxsw_sp_port.

This lead to a bloated struct storing both physical properties of the
port (e.g., autoneg status) as well as logical properties of an upper
bridge port (e.g., learning, mrouter indication). While this might work
well for simple devices, it proved to be hard to extend when stacked
devices were taken into account and more advanced use-cases (e.g., IGMP
snooping) considered.

This patch removes the excess information from the above struct and
instead stores it in more appropriate structs that represent the bridge
port, the bridge itself and a VLAN configured on the bridge port.

The membership of a port in a bridge is denoted using the Port-VLAN
struct, which points to the bridge port and also member in the bridge
VLAN group of the VLAN it represents. This allows us to completely
remove the vPort abstraction and consolidate many of the code paths
relating to VLAN-aware and unaware bridges.

Note that the FID / vFID code is currently duplicated, but this will
soon go away when the common FID core will be introduced.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a vPort is destroyed, it leaves the FID it's currently mapped to
(if any) and drops the reference. The FID's leave function expects to
get the vPort as its argument, but this will have to change when the
vPort model is retired.

Change the function signature to expect a Port-VLAN struct instead and
patch the call sites accordingly.

The code introduced in this patch will be removed later in the patchset,
but this intermediary step is required in order to ease the code review.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the first step in the transition from the vPort model to a
unified Port-VLAN structure. The new structure is defined and created /
destroyed upon invocation of the 8021q ndos, but it's not actually used
throughout the code.

Subsequent patches will initialize it correctly and also create /
destroy it upon switchdev's VLAN object.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently transition the port to "Virtual mode" upon the creation of
its first VLAN upper, as we need to classify incoming packets to a FID
using {Port, VID} and not only the VID.

However, it's more appropriate to transition the port to this mode when
the {Port, VID} are actually mapped to a FID. Either during the
enslavement of the VLAN upper to a VLAN-unaware bridge or the
configuration of a router port.

Do this change now in preparation for the introduction of the FID core,
where this operation will be encapsulated.

To prevent regressions, this patch also explicitly configures an OVS
slave to "Virtual mode". Otherwise, a packet that didn't hit an ACL rule
could be classified to an existing FID based on a global VID-to-FID
mapping, thus not incurring a FID mis-classification, which would
otherwise trap the packet to the CPU to be processed by the OVS daemon.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PVID is a port attribute and should therefore reside in the main driver
file and not the switchdev specific one.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We no longer batch VLAN operations, so there's no need to set the
learning state for a range of VLANs.

Use a common function to set the learning state for a Port-VLAN, thereby
making the code saner more receptive for upcoming changes.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

switchdev's VLAN object has the ability to describe a range of VLAN IDs,
but this is only used when VLAN operations are done using the SELF flag,
which is something we would like to remove as it allows one to bypass
the bridge driver.

Do VLAN operations on a per-VLAN basis, thereby simplifying the code and
preparing it for refactoring in a follow-up patchset.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FIB notification block logically belongs inside the router specific
struct, so move it there.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The router interfaces (RIFs) array is of no interest to code outside the
routing realm, so declare it inside the router specific struct instead
of the chip-wide one.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some attributes in the global chip struct are only relevant for bridge
operation, so encapsulate them in their own struct that isn't exposed to
non-bridge code.

This will also help us later, when we add more bridge-specific
attributes.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a similar fashion to previous patch, the router structure
('mlxsw_sp_router') doesn't need to be accessible to anyone, but the
router code located at spectrum_router.c

Make this apparent and reduce its scope by defining it there.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The shared buffer structure ('mlxsw_sp_sb') doesn't need to be
accessible to anyone, but the shared buffer code located at
spectrum_buffers.c

Make this apparent and reduce its scope by defining it there.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a netdev is enslaved to a VRF master, its router interface (RIF)
needs to be destroyed (if exists) and a new one created using the
corresponding virtual router (VR).

>From the driver's perspective, the above is equivalent to an inetaddr
event sent for this netdev. Therefore, when a port netdev (or its
uppers) are enslaved to a VRF master, call the same function that
would've been called had a NETDEV_UP was sent for this netdev in the
inetaddr notification chain.

This patch also fixes a bug when a LAG netdev with an existing RIF is
enslaved to a VRF. Before this patch, each LAG port would drop the
reference on the RIF, but would re-join the same one (in the wrong VR)
soon after. With this patch, the corresponding RIF is first destroyed
and a new one is created using the correct VR.

Fixes: 7179eb5a ("mlxsw: spectrum_router: Add support for VRFs")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For forwarding using ACL action, HW needs a valid FID to be setup. It
does not actually use it, so it can be any valid FID. So create a dummy
FID only for this purpose.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement part of multipurpose Virtual Router and Forwarding Domain
Action that takes care of setting up FID. We need to use it to be able
to forward packets using ACL action when no FID is associated on RX.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the return allocated index and err value are multiplexed.
This patch changes the API to decouple the ret value from the allocated
index.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As explained in the previous patch, the cell size may change in future
devices, so query it from the firmware instead of hard coding it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sizes and thresholds of the priority group (PG) buffers are
configured in cells, which represent a specific amount of bytes.

The cell size can vary in different devices, so it's better to query it
from the firmware than hard coding it.

Refactor the code dealing with this value into different functions, so
that it will be easier to make the conversion in the next patch.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently hard code the maximum number of ports in the driver, but
this may change in future devices, so query it from the firmware
instead.

Fallback to a maximum of 64 ports in case this number can't be queried.
This should only happen in SwitchX-2 for which this number is correct.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>