Merge branches 'samsung/exynos-dt2' and 'samsung/s3c24xx-dt2' into next/drivers

This is the merge base for samsung/common-clk-audio
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/clock/exynos4-clock.txt

@@ -102,6 +102,7 @@ Exynos4 SoC and this is specified where applicable.
   sclk_spi0_isp       174     Exynos4x12
   sclk_spi1_isp       175     Exynos4x12
   sclk_uart_isp       176     Exynos4x12
+  sclk_fimg2d         177
 
 	      [Peripheral Clock Gates]
 
@@ -129,7 +130,7 @@ Exynos4 SoC and this is specified where applicable.
   smmu_mfcl           274
   smmu_mfcr           275
   g3d                 276
-  g2d                 277     Exynos4210
+  g2d                 277
   rotator             278     Exynos4210
   mdma                279     Exynos4210
   smmu_g2d            280     Exynos4210

Documentation/devicetree/bindings/gpu/samsung-g2d.txt

@@ -10,11 +10,16 @@ Required properties:
 	  mapped region.
 
   - interrupts : G2D interrupt number to the CPU.
+  - clocks : from common clock binding: handle to G2D clocks.
+  - clock-names : from common clock binding: must contain "sclk_fimg2d" and
+		  "fimg2d", corresponding to entries in the clocks property.
 
 Example:
 	g2d@12800000 {
 		compatible = "samsung,s5pv210-g2d";
 		reg = <0x12800000 0x1000>;
 		interrupts = <0 89 0>;
+		clocks = <&clock 177>, <&clock 277>;
+		clock-names = "sclk_fimg2d", "fimg2d";
 		status = "disabled";
 	};

Documentation/devicetree/bindings/media/s5p-mfc.txt

@@ -15,6 +15,9 @@ Required properties:
 	  mapped region.
 
   - interrupts : MFC interrupt number to the CPU.
+  - clocks : from common clock binding: handle to mfc clocks.
+  - clock-names : from common clock binding: must contain "sclk_mfc" and "mfc",
+		  corresponding to entries in the clocks property.
 
   - samsung,mfc-r : Base address of the first memory bank used by MFC
 		    for DMA contiguous memory allocation and its size.
@@ -34,6 +37,8 @@ mfc: codec@13400000 {
 	reg = <0x13400000 0x10000>;
 	interrupts = <0 94 0>;
 	samsung,power-domain = <&pd_mfc>;
+	clocks = <&clock 170>, <&clock 273>;
+	clock-names = "sclk_mfc", "mfc";
 };
 
 Board specific DT entry:

Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt

@@ -25,8 +25,18 @@ Required Properties:
 
   - gpio-controller: identifies the node as a gpio controller and pin bank.
   - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
-    binding is used, the amount of cells must be specified as 2. See generic
-    GPIO binding documentation for description of particular cells.
+    binding is used, the amount of cells must be specified as 2. See the below
+    mentioned gpio binding representation for description of particular cells.
+
+	Eg: <&gpx2 6 0>
+	<[phandle of the gpio controller node]
+	[pin number within the gpio controller]
+	[flags]>
+
+	Values for gpio specifier:
+	- Pin number: is a value between 0 to 7.
+	- Flags: 0 - Active High
+		 1 - Active Low
 
 - Pin mux/config groups as child nodes: The pin mux (selecting pin function
   mode) and pin config (pull up/down, driver strength) settings are represented
@@ -274,3 +284,33 @@ Example 4: Set up the default pin state for uart controller.
 
 		pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
 	}
+
+Example 5: A display port client node that supports 'default' pinctrl state
+	   and gpio binding.
+
+	display-port-controller {
+		/* ... */
+
+		samsung,hpd-gpio = <&gpx2 6 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dp_hpd>;
+	};
+
+Example 6: Request the gpio for display port controller
+
+	static int exynos_dp_probe(struct platform_device *pdev)
+	{
+		int hpd_gpio, ret;
+		struct device *dev = &pdev->dev;
+		struct device_node *dp_node = dev->of_node;
+
+		/* ... */
+
+		hpd_gpio = of_get_named_gpio(dp_node, "samsung,hpd-gpio", 0);
+
+		/* ... */
+
+		ret = devm_gpio_request_one(&pdev->dev, hpd_gpio, GPIOF_IN,
+					    "hpd_gpio");
+		/* ... */
+	}

Documentation/devicetree/bindings/usb/exynos-usb.txt

@@ -48,3 +48,37 @@ Example:
 		clocks = <&clock 285>;
 		clock-names = "usbhost";
 	};
+
+DWC3
+Required properties:
+ - compatible: should be "samsung,exynos5250-dwusb3" for USB 3.0 DWC3
+	       controller.
+ - #address-cells, #size-cells : should be '1' if the device has sub-nodes
+				 with 'reg' property.
+ - ranges: allows valid 1:1 translation between child's address space and
+	   parent's address space
+ - clocks: Clock IDs array as required by the controller.
+ - clock-names: names of clocks correseponding to IDs in the clock property
+
+Sub-nodes:
+The dwc3 core should be added as subnode to Exynos dwc3 glue.
+- dwc3 :
+   The binding details of dwc3 can be found in:
+   Documentation/devicetree/bindings/usb/dwc3.txt
+
+Example:
+	usb@12000000 {
+		compatible = "samsung,exynos5250-dwusb3";
+		clocks = <&clock 286>;
+		clock-names = "usbdrd30";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		dwc3 {
+			compatible = "synopsys,dwc3";
+			reg = <0x12000000 0x10000>;
+			interrupts = <0 72 0>;
+			usb-phy = <&usb2_phy &usb3_phy>;
+		};
+	};

Documentation/devicetree/bindings/video/exynos_dp.txt

@@ -21,6 +21,10 @@ Required properties for dp-controller:
 		of memory mapped region.
 	-interrupts:
 		interrupt combiner values.
+	-clocks:
+		from common clock binding: handle to dp clock.
+	-clock-names:
+		from common clock binding: Shall be "dp".
 	-interrupt-parent:
 		phandle to Interrupt combiner node.
 	-samsung,color-space:
@@ -61,6 +65,8 @@ SOC specific portion:
 		reg = <0x145b0000 0x10000>;
 		interrupts = <10 3>;
 		interrupt-parent = <&combiner>;
+		clocks = <&clock 342>;
+		clock-names = "dp";
 
 		dptx-phy {
 			reg = <0x10040720>;

arch/arm/boot/dts/Makefile

@@ -159,6 +159,7 @@ dtb-$(CONFIG_ARCH_U8500) += snowball.dtb \
 	hrefprev60.dtb \
 	hrefv60plus.dtb \
 	ccu9540.dtb
+dtb-$(CONFIG_ARCH_S3C24XX) += s3c2416-smdk2416.dtb
 dtb-$(CONFIG_ARCH_SHMOBILE) += emev2-kzm9d.dtb \
 	r8a7740-armadillo800eva.dtb \
 	r8a7778-bockw.dtb \

arch/arm/boot/dts/exynos4.dtsi

@@ -160,6 +160,8 @@
 		reg = <0x13400000 0x10000>;
 		interrupts = <0 94 0>;
 		samsung,power-domain = <&pd_mfc>;
+		clocks = <&clock 170>, <&clock 273>;
+		clock-names = "sclk_mfc", "mfc";
 		status = "disabled";
 	};
 

arch/arm/boot/dts/exynos4210-origen.dts

@@ -41,6 +41,10 @@
 		enable-active-high;
 	};
 
+	tmu@100C0000 {
+		status = "okay";
+	};
+
 	sdhci@12530000 {
 		bus-width = <4>;
 		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
@@ -83,6 +87,150 @@
 		status = "okay";
 	};
 
+	i2c@13860000 {
+		status = "okay";
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <20000>;
+		pinctrl-0 = <&i2c0_bus>;
+		pinctrl-names = "default";
+
+		max8997_pmic@66 {
+			compatible = "maxim,max8997-pmic";
+			reg = <0x66>;
+			interrupt-parent = <&gpx0>;
+			interrupts = <4 0>, <3 0>;
+
+			max8997,pmic-buck1-dvs-voltage = <1350000>;
+			max8997,pmic-buck2-dvs-voltage = <1100000>;
+			max8997,pmic-buck5-dvs-voltage = <1200000>;
+
+			regulators {
+				ldo1_reg: LDO1 {
+					regulator-name = "VDD_ABB_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo2_reg: LDO2 {
+					regulator-name = "VDD_ALIVE_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+				};
+
+				ldo3_reg: LDO3 {
+					regulator-name = "VMIPI_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+				};
+
+				ldo4_reg: LDO4 {
+					regulator-name = "VDD_RTC_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt	= <1800000>;
+					regulator-always-on;
+				};
+
+				ldo6_reg: LDO6 {
+					regulator-name = "VMIPI_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt	= <1800000>;
+					regulator-always-on;
+				};
+
+				ldo7_reg: LDO7 {
+					regulator-name = "VDD_AUD_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt	= <1800000>;
+				};
+
+				ldo8_reg: LDO8 {
+					regulator-name = "VADC_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt	= <3300000>;
+				};
+
+				ldo9_reg: LDO9 {
+					regulator-name = "DVDD_SWB_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt	= <2800000>;
+					regulator-always-on;
+				};
+
+				ldo10_reg: LDO10 {
+					regulator-name = "VDD_PLL_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt	= <1100000>;
+					regulator-always-on;
+				};
+
+				ldo11_reg: LDO11 {
+					regulator-name = "VDD_AUD_3V";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt	= <3000000>;
+				};
+
+				ldo14_reg: LDO14 {
+					regulator-name = "AVDD18_SWB_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt	= <1800000>;
+					regulator-always-on;
+				};
+
+				ldo17_reg: LDO17 {
+					regulator-name = "VDD_SWB_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt	= <3300000>;
+					regulator-always-on;
+				};
+
+				ldo21_reg: LDO21 {
+					regulator-name = "VDD_MIF_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt	= <1200000>;
+					regulator-always-on;
+				};
+
+				buck1_reg: BUCK1 {
+					regulator-name = "VDD_ARM_1.2V";
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt	= <1350000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck2_reg: BUCK2 {
+					regulator-name = "VDD_INT_1.1V";
+					regulator-min-microvolt = <900000>;
+					regulator-max-microvolt	= <1100000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck3_reg: BUCK3 {
+					regulator-name = "VDD_G3D_1.1V";
+					regulator-min-microvolt = <900000>;
+					regulator-max-microvolt = <1100000>;
+				};
+
+				buck5_reg: BUCK5 {
+					regulator-name = "VDDQ_M1M2_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				buck7_reg: BUCK7 {
+					regulator-name = "VDD_LCD_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+					regulator-always-on;
+				};
+			};
+		};
+	};
+
 	gpio_keys {
 		compatible = "gpio-keys";
 		#address-cells = <1>;
@@ -143,4 +291,25 @@
 			clock-frequency = <24000000>;
 		};
 	};
+
+	fimd@11c00000 {
+		pinctrl-0 = <&lcd_en &lcd_clk &lcd_data24 &pwm0_out>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+
+	display-timings {
+		native-mode = <&timing0>;
+		timing0: timing {
+			clock-frequency = <50000>;
+			hactive = <1024>;
+			vactive = <600>;
+			hfront-porch = <64>;
+			hback-porch = <16>;
+			hsync-len = <48>;
+			vback-porch = <64>;
+			vfront-porch = <16>;
+			vsync-len = <3>;
+		};
+	};
 };

arch/arm/boot/dts/exynos4210-pinctrl.dtsi

@@ -330,6 +330,95 @@
 			samsung,pin-pud = <3>;
 			samsung,pin-drv = <0>;
 		};
+
+		pwm0_out: pwm0-out {
+			samsung,pins = "gpd0-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		pwm1_out: pwm1-out {
+			samsung,pins = "gpd0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		pwm2_out: pwm2-out {
+			samsung,pins = "gpd0-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		pwm3_out: pwm3-out {
+			samsung,pins = "gpd0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		lcd_ctrl: lcd-ctrl {
+			samsung,pins = "gpd0-0", "gpd0-1";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		lcd_sync: lcd-sync {
+			samsung,pins = "gpf0-0", "gpf0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		lcd_en: lcd-en {
+			samsung,pins = "gpe3-4";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		lcd_clk: lcd-clk {
+			samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		lcd_data16: lcd-data-width16 {
+			samsung,pins = "gpf0-7", "gpf1-0", "gpf1-1", "gpf1-2",
+					"gpf1-3", "gpf1-6", "gpf1-7", "gpf2-0",
+					"gpf2-1", "gpf2-2", "gpf2-3", "gpf2-7",
+					"gpf3-0", "gpf3-1", "gpf3-2", "gpf3-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		lcd_data18: lcd-data-width18 {
+			samsung,pins = "gpf0-6", "gpf0-7", "gpf1-0", "gpf1-1",
+					"gpf1-2", "gpf1-3", "gpf1-6", "gpf1-7",
+					"gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
+					"gpf2-6", "gpf2-7", "gpf3-0", "gpf3-1",
+					"gpf3-2", "gpf3-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		lcd_data24: lcd-data-width24 {
+			samsung,pins = "gpf0-4", "gpf0-5", "gpf0-6", "gpf0-7",
+					"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3",
+					"gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7",
+					"gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
+					"gpf2-4", "gpf2-5", "gpf2-6", "gpf2-7",
+					"gpf3-0", "gpf3-1", "gpf3-2", "gpf3-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
 	};
 
 	pinctrl@11000000 {

arch/arm/boot/dts/exynos4210.dtsi

@@ -112,12 +112,17 @@
 		interrupt-parent = <&combiner>;
 		reg = <0x100C0000 0x100>;
 		interrupts = <2 4>;
+		clocks = <&clock 383>;
+		clock-names = "tmu_apbif";
+		status = "disabled";
 	};
 
 	g2d@12800000 {
 		compatible = "samsung,s5pv210-g2d";
 		reg = <0x12800000 0x1000>;
 		interrupts = <0 89 0>;
+		clocks = <&clock 177>, <&clock 277>;
+		clock-names = "sclk_fimg2d", "fimg2d";
 		status = "disabled";
 	};
 };

arch/arm/boot/dts/exynos4412-odroidx.dts

@@ -43,6 +43,7 @@
 		#size-cells = <0>;
 		pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
 		pinctrl-names = "default";
+		vmmc-supply = <&ldo20_reg &buck8_reg>;
 		status = "okay";
 
 		num-slots = <1>;
@@ -78,6 +79,7 @@
 		bus-width = <4>;
 		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
 		pinctrl-names = "default";
+		vmmc-supply = <&ldo4_reg &ldo21_reg>;
 		status = "okay";
 	};
 
@@ -108,4 +110,199 @@
 			clock-frequency = <24000000>;
 		};
 	};
+
+	i2c@13860000 {
+		pinctrl-0 = <&i2c0_bus>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		max77686: pmic@09 {
+			compatible = "maxim,max77686";
+			reg = <0x09>;
+
+			voltage-regulators {
+				ldo1_reg: LDO1 {
+					regulator-name = "VDD_ALIVE_1.0V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				ldo2_reg: LDO2 {
+					regulator-name = "VDDQ_M1_2_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo3_reg: LDO3 {
+					regulator-name = "VDDQ_EXT_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo4_reg: LDO4 {
+					regulator-name = "VDDQ_MMC2_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo5_reg: LDO5 {
+					regulator-name = "VDDQ_MMC1_3_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo6_reg: LDO6 {
+					regulator-name = "VDD10_MPLL_1.0V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				ldo7_reg: LDO7 {
+					regulator-name = "VDD10_XPLL_1.0V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				ldo11_reg: LDO11 {
+					regulator-name = "VDD18_ABB1_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo12_reg: LDO12 {
+					regulator-name = "VDD33_USB_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo13_reg: LDO13 {
+					regulator-name = "VDDQ_C2C_W_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo14_reg: LDO14 {
+					regulator-name = "VDD18_ABB0_2_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo15_reg: LDO15 {
+					regulator-name = "VDD10_HSIC_1.0V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo16_reg: LDO16 {
+					regulator-name = "VDD18_HSIC_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo20_reg: LDO20 {
+					regulator-name = "LDO20_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-boot-on;
+				};
+
+				ldo21_reg: LDO21 {
+					regulator-name = "LDO21_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo25_reg: LDO25 {
+					regulator-name = "VDDQ_LCD_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck1_reg: BUCK1 {
+					regulator-name = "vdd_mif";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck2_reg: BUCK2 {
+					regulator-name = "vdd_arm";
+					regulator-min-microvolt = <900000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck3_reg: BUCK3 {
+					regulator-name = "vdd_int";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck4_reg: BUCK4 {
+					regulator-name = "vdd_g3d";
+					regulator-min-microvolt = <900000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-microvolt-offset = <50000>;
+				};
+
+				buck5_reg: BUCK5 {
+					regulator-name = "VDDQ_CKEM1_2_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck6_reg: BUCK6 {
+					regulator-name = "BUCK6_1.35V";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck7_reg: BUCK7 {
+					regulator-name = "BUCK7_2.0V";
+					regulator-min-microvolt = <2000000>;
+					regulator-max-microvolt = <2000000>;
+					regulator-always-on;
+				};
+
+				buck8_reg: BUCK8 {
+					regulator-name = "BUCK8_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+				};
+			};
+		};
+	};
 };

arch/arm/boot/dts/exynos4412-origen.dts

@@ -36,6 +36,72 @@
 		enable-active-high;
 	};
 
+	pinctrl@11000000 {
+		keypad_rows: keypad-rows {
+			samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		keypad_cols: keypad-cols {
+			samsung,pins = "gpx1-0", "gpx1-1";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+	};
+
+	keypad@100A0000 {
+		samsung,keypad-num-rows = <3>;
+		samsung,keypad-num-columns = <2>;
+		linux,keypad-no-autorepeat;
+		linux,keypad-wakeup;
+		pinctrl-0 = <&keypad_rows &keypad_cols>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		key_home {
+			keypad,row = <0>;
+			keypad,column = <0>;
+			linux,code = <102>;
+		};
+
+		key_down {
+			keypad,row = <0>;
+			keypad,column = <1>;
+			linux,code = <108>;
+		};
+
+		key_up {
+			keypad,row = <1>;
+			keypad,column = <0>;
+			linux,code = <103>;
+		};
+
+		key_menu {
+			keypad,row = <1>;
+			keypad,column = <1>;
+			linux,code = <139>;
+		};
+
+		key_back {
+			keypad,row = <2>;
+			keypad,column = <0>;
+			linux,code = <158>;
+		};
+
+		key_enter {
+			keypad,row = <2>;
+			keypad,column = <1>;
+			linux,code = <28>;
+		};
+	};
+
+	g2d@10800000 {
+		status = "okay";
+	};
+
 	sdhci@12530000 {
 		bus-width = <4>;
 		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;

arch/arm/boot/dts/exynos4412-smdk4412.dts

@@ -31,8 +31,91 @@
 		status = "okay";
 	};
 
-	g2d@10800000 {
+	pinctrl@11000000 {
+		keypad_rows: keypad-rows {
+			samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		keypad_cols: keypad-cols {
+			samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
+				       "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+	};
+
+	keypad@100A0000 {
+		samsung,keypad-num-rows = <3>;
+		samsung,keypad-num-columns = <8>;
+		linux,keypad-no-autorepeat;
+		linux,keypad-wakeup;
+		pinctrl-0 = <&keypad_rows &keypad_cols>;
+		pinctrl-names = "default";
 		status = "okay";
+
+		key_1 {
+			keypad,row = <1>;
+			keypad,column = <3>;
+			linux,code = <2>;
+		};
+
+		key_2 {
+			keypad,row = <1>;
+			keypad,column = <4>;
+			linux,code = <3>;
+		};
+
+		key_3 {
+			keypad,row = <1>;
+			keypad,column = <5>;
+			linux,code = <4>;
+		};
+
+		key_4 {
+			keypad,row = <1>;
+			keypad,column = <6>;
+			linux,code = <5>;
+		};
+
+		key_5 {
+			keypad,row = <1>;
+			keypad,column = <7>;
+			linux,code = <6>;
+		};
+
+		key_A {
+			keypad,row = <2>;
+			keypad,column = <6>;
+			linux,code = <30>;
+		};
+
+		key_B {
+			keypad,row = <2>;
+			keypad,column = <7>;
+			linux,code = <48>;
+		};
+
+		key_C {
+			keypad,row = <0>;
+			keypad,column = <5>;
+			linux,code = <46>;
+		};
+
+		key_D {
+			keypad,row = <2>;
+			keypad,column = <5>;
+			linux,code = <32>;
+		};
+
+		key_E {
+			keypad,row = <0>;
+			keypad,column = <7>;
+			linux,code = <18>;
+		};
 	};
 
 	sdhci@12530000 {

arch/arm/boot/dts/exynos4x12-pinctrl.dtsi

@@ -778,62 +778,6 @@
 			samsung,pin-drv = <3>;
 		};
 
-		keypad_col0: keypad-col0 {
-			samsung,pins = "gpl2-0";
-			samsung,pin-function = <3>;
-			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
-		};
-
-		keypad_col1: keypad-col1 {
-			samsung,pins = "gpl2-1";
-			samsung,pin-function = <3>;
-			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
-		};
-
-		keypad_col2: keypad-col2 {
-			samsung,pins = "gpl2-2";
-			samsung,pin-function = <3>;
-			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
-		};
-
-		keypad_col3: keypad-col3 {
-			samsung,pins = "gpl2-3";
-			samsung,pin-function = <3>;
-			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
-		};
-
-		keypad_col4: keypad-col4 {
-			samsung,pins = "gpl2-4";
-			samsung,pin-function = <3>;
-			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
-		};
-
-		keypad_col5: keypad-col5 {
-			samsung,pins = "gpl2-5";
-			samsung,pin-function = <3>;
-			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
-		};
-
-		keypad_col6: keypad-col6 {
-			samsung,pins = "gpl2-6";
-			samsung,pin-function = <3>;
-			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
-		};
-
-		keypad_col7: keypad-col7 {
-			samsung,pins = "gpl2-7";
-			samsung,pin-function = <3>;
-			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
-		};
-
 		cam_port_b: cam-port-b {
 			samsung,pins = "gpm0-0", "gpm0-1", "gpm0-2", "gpm0-3",
 					"gpm0-4", "gpm0-5", "gpm0-6", "gpm0-7",

arch/arm/boot/dts/exynos4x12.dtsi

@@ -28,14 +28,6 @@
 		pinctrl3 = &pinctrl_3;
 	};
 
-	combiner:interrupt-controller@10440000 {
-		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
-			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
-			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
-			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
-			     <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>;
-	};
-
 	clock: clock-controller@0x10030000 {
 		compatible = "samsung,exynos4412-clock";
 		reg = <0x10030000 0x20000>;
@@ -77,6 +69,8 @@
 		compatible = "samsung,exynos4212-g2d";
 		reg = <0x10800000 0x1000>;
 		interrupts = <0 89 0>;
+		clocks = <&clock 177>, <&clock 277>;
+		clock-names = "sclk_fimg2d", "fimg2d";
 		status = "disabled";
 	};
 };

arch/arm/boot/dts/exynos5250-arndale.dts

@@ -449,4 +449,35 @@
 			clock-frequency = <24000000>;
 		};
 	};
+
+	dp-controller {
+		samsung,color-space = <0>;
+		samsung,dynamic-range = <0>;
+		samsung,ycbcr-coeff = <0>;
+		samsung,color-depth = <1>;
+		samsung,link-rate = <0x0a>;
+		samsung,lane-count = <4>;
+	};
+
+	fimd: fimd@14400000 {
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing@0 {
+				/* 2560x1600 DP panel */
+				clock-frequency = <50000>;
+				hactive = <2560>;
+				vactive = <1600>;
+				hfront-porch = <48>;
+				hback-porch = <80>;
+				hsync-len = <32>;
+				vback-porch = <16>;
+				vfront-porch = <8>;
+				vsync-len = <6>;
+			};
+		};
+	};
+
+	rtc {
+		status = "okay";
+	};
 };

arch/arm/boot/dts/exynos5250-pinctrl.dtsi

@@ -553,6 +553,13 @@
 			samsung,pin-pud = <0>;
 			samaung,pin-drv = <0>;
 		};
+
+		dp_hpd: dp_hpd {
+			samsung,pins = "gpx0-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samaung,pin-drv = <0>;
+		};
 	};
 
 	pinctrl@13400000 {

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -37,6 +37,30 @@
 		};
 	};
 
+	vdd:fixed-regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	dbvdd:fixed-regulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "dbvdd-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	spkvdd:fixed-regulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "spkvdd-supply";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
 	i2c@12C70000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <20000>;
@@ -47,8 +71,17 @@
 		};
 
 		wm8994: wm8994@1a {
-			 compatible = "wlf,wm8994";
-			 reg = <0x1a>;
+			compatible = "wlf,wm8994";
+			reg = <0x1a>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			AVDD2-supply = <&vdd>;
+			CPVDD-supply = <&vdd>;
+			DBVDD-supply = <&dbvdd>;
+			SPKVDD1-supply = <&spkvdd>;
+			SPKVDD2-supply = <&spkvdd>;
 		};
 	};
 
@@ -224,6 +257,9 @@
 		samsung,color-depth = <1>;
 		samsung,link-rate = <0x0a>;
 		samsung,lane-count = <4>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&dp_hpd>;
 	};
 
 	display-timings {

arch/arm/boot/dts/exynos5250-snow.dts

@@ -171,6 +171,10 @@
 		};
 	};
 
+	rtc {
+		status = "okay";
+	};
+
 	/*
 	 * On Snow we've got SIP WiFi and so can keep drive strengths low to
 	 * reduce EMI.

arch/arm/boot/dts/exynos5250.dtsi

@@ -479,6 +479,36 @@
 		pinctrl-0 = <&i2s2_bus>;
 	};
 
+	usb@12000000 {
+		compatible = "samsung,exynos5250-dwusb3";
+		clocks = <&clock 286>;
+		clock-names = "usbdrd30";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		dwc3 {
+			compatible = "synopsys,dwc3";
+			reg = <0x12000000 0x10000>;
+			interrupts = <0 72 0>;
+			usb-phy = <&usb2_phy &usb3_phy>;
+		};
+	};
+
+	usb3_phy: usbphy@12100000 {
+		compatible = "samsung,exynos5250-usb3phy";
+		reg = <0x12100000 0x100>;
+		clocks = <&clock 1>, <&clock 286>;
+		clock-names = "ext_xtal", "usbdrd30";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		usbphy-sys {
+			reg = <0x10040704 0x8>;
+		};
+	};
+
 	usb@12110000 {
 		compatible = "samsung,exynos4210-ehci";
 		reg = <0x12110000 0x100>;
@@ -497,7 +527,7 @@
 		clock-names = "usbhost";
 	};
 
-	usbphy@12130000 {
+	usb2_phy: usbphy@12130000 {
 		compatible = "samsung,exynos5250-usb2phy";
 		reg = <0x12130000 0x100>;
 		clocks = <&clock 1>, <&clock 285>;
@@ -621,6 +651,8 @@
 		reg = <0x145b0000 0x1000>;
 		interrupts = <10 3>;
 		interrupt-parent = <&combiner>;
+		clocks = <&clock 342>;
+		clock-names = "dp";
 		#address-cells = <1>;
 		#size-cells = <0>;
 

arch/arm/boot/dts/exynos5440-sd5v1.dts

@@ -17,7 +17,7 @@
 	compatible = "samsung,sd5v1", "samsung,exynos5440";
 
 	chosen {
-		bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel early_printk no_console_suspend mem=2048M@0x80000000 console=ttySAC0,115200";
+		bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel early_printk no_console_suspend mem=2048M@0x80000000 mem=6144M@0x100000000 console=ttySAC0,115200";
 	};
 
 	fixed-rate-clocks {

arch/arm/boot/dts/exynos5440-ssdk5440.dts

@@ -17,11 +17,46 @@
 	compatible = "samsung,ssdk5440", "samsung,exynos5440";
 
 	chosen {
-		bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel early_printk no_console_suspend mem=2048M@0x80000000 console=ttySAC0,115200";
+		bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel early_printk no_console_suspend mem=2048M@0x80000000 mem=6144M@0x100000000 console=ttySAC0,115200";
 	};
 
-	spi {
-		status = "disabled";
+	spi_0: spi@D0000 {
+
+		flash: w25q128@0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "winbond,w25q128";
+			spi-max-frequency = <15625000>;
+			reg = <0>;
+			controller-data {
+				samsung,spi-feedback-delay = <0>;
+			};
+
+			partition@00000 {
+				label = "BootLoader";
+				reg = <0x60000 0x80000>;
+				read-only;
+			};
+
+			partition@e0000 {
+				label = "Recovery-Kernel";
+				reg = <0xe0000 0x300000>;
+				read-only;
+			};
+
+			partition@3e0000 {
+				label = "CRAM-FS";
+				reg = <0x3e0000 0x700000>;
+				read-only;
+			};
+
+			partition@ae0000 {
+				label = "User-Data";
+				reg = <0xae0000 0x520000>;
+			};
+
+		};
+
 	};
 
 	fixed-rate-clocks {

arch/arm/boot/dts/exynos5440.dtsi

@@ -16,6 +16,10 @@
 
 	interrupt-parent = <&gic>;
 
+	aliases {
+		spi0 = &spi_0;
+	};
+
 	clock: clock-controller@0x160000 {
 		compatible = "samsung,exynos5440-clock";
 		reg = <0x160000 0x1000>;
@@ -79,8 +83,13 @@
 		interrupts = <0 57 0>;
 		operating-points = <
 				/* KHz	  uV */
+				1500000 1100000
+				1400000 1075000
+				1300000 1050000
 				1200000 1025000
+				1100000 1000000
 				1000000 975000
+				900000  950000
 				800000  925000
 		>;
 	};
@@ -101,14 +110,14 @@
 		clock-names = "uart", "clk_uart_baud0";
 	};
 
-	spi {
-		compatible = "samsung,exynos4210-spi";
-		reg = <0xD0000 0x1000>;
+	spi_0: spi@D0000 {
+		compatible = "samsung,exynos5440-spi";
+		reg = <0xD0000 0x100>;
 		interrupts = <0 4 0>;
-		tx-dma-channel = <&pdma0 5>; /* preliminary */
-		rx-dma-channel = <&pdma0 4>; /* preliminary */
 		#address-cells = <1>;
 		#size-cells = <0>;
+		samsung,spi-src-clk = <0>;
+		num-cs = <1>;
 		clocks = <&clock 21>, <&clock 16>;
 		clock-names = "spi", "spi_busclk0";
 	};
@@ -184,28 +193,6 @@
 		compatible = "arm,amba-bus";
 		interrupt-parent = <&gic>;
 		ranges;
-
-		pdma0: pdma@00121000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x121000 0x1000>;
-			interrupts = <0 46 0>;
-			clocks = <&clock 8>;
-			clock-names = "apb_pclk";
-			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
-		};
-
-		pdma1: pdma@00120000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x120000 0x1000>;
-			interrupts = <0 47 0>;
-			clocks = <&clock 8>;
-			clock-names = "apb_pclk";
-			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
-		};
 	};
 
 	rtc {
@@ -214,6 +201,29 @@
 		interrupts = <0 17 0>, <0 16 0>;
 		clocks = <&clock 21>;
 		clock-names = "rtc";
-		status = "disabled";
+	};
+
+	sata@210000 {
+		compatible = "snps,exynos5440-ahci";
+		reg = <0x210000 0x10000>;
+		interrupts = <0 30 0>;
+		clocks = <&clock 23>;
+		clock-names = "sata";
+	};
+
+	ohci@220000 {
+		compatible = "samsung,exynos5440-ohci";
+		reg = <0x220000 0x1000>;
+		interrupts = <0 29 0>;
+		clocks = <&clock 24>;
+		clock-names = "usbhost";
+	};
+
+	ehci@221000 {
+		compatible = "samsung,exynos5440-ehci";
+		reg = <0x221000 0x1000>;
+		interrupts = <0 29 0>;
+		clocks = <&clock 24>;
+		clock-names = "usbhost";
 	};
 };

arch/arm/boot/dts/s3c2416-pinctrl.dtsi

+/*
+ * Samsung S3C2416 pinctrl settings
+ *
+ * Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+&pinctrl_0 {
+	/*
+	 * Pin banks
+	 */
+
+	gpa: gpa {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpb: gpb {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpc: gpc {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpd: gpd {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpe: gpe {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpf: gpf {
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg: gpg {
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gph: gph {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpj: gpj {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpk: gpk {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpl: gpl {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpm: gpm {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	/*
+	 * Pin groups
+	 */
+
+	uart0_data: uart0-data {
+		samsung,pins = "gph-0", "gph-1";
+		samsung,pin-function = <2>;
+	};
+
+	uart0_fctl: uart0-fctl {
+		samsung,pins = "gph-8", "gph-9";
+		samsung,pin-function = <2>;
+	};
+
+	uart1_data: uart1-data {
+		samsung,pins = "gph-2", "gph-3";
+		samsung,pin-function = <2>;
+	};
+
+	uart1_fctl: uart1-fctl {
+		samsung,pins = "gph-10", "gph-11";
+		samsung,pin-function = <2>;
+	};
+
+	uart2_data: uart2-data {
+		samsung,pins = "gph-4", "gph-5";
+		samsung,pin-function = <2>;
+	};
+
+	uart2_fctl: uart2-fctl {
+		samsung,pins = "gph-6", "gph-7";
+		samsung,pin-function = <2>;
+	};
+
+	uart3_data: uart3-data {
+		samsung,pins = "gph-6", "gph-7";
+		samsung,pin-function = <2>;
+	};
+
+	extuart_clk: extuart-clk {
+		samsung,pins = "gph-12";
+		samsung,pin-function = <2>;
+	};
+
+	i2c0_bus: i2c0-bus {
+		samsung,pins = "gpe-14", "gpe-15";
+		samsung,pin-function = <2>;
+	};
+
+	spi0_bus: spi0-bus {
+		samsung,pins = "gpe-11", "gpe-12", "gpe-13";
+		samsung,pin-function = <2>;
+	};
+
+	sd0_clk: sd0-clk {
+		samsung,pins = "gpe-5";
+		samsung,pin-function = <2>;
+	};
+
+	sd0_cmd: sd0-cmd {
+		samsung,pins = "gpe-6";
+		samsung,pin-function = <2>;
+	};
+
+	sd0_bus1: sd0-bus1 {
+		samsung,pins = "gpe-7";
+		samsung,pin-function = <2>;
+	};
+
+	sd0_bus4: sd0-bus4 {
+		samsung,pins = "gpe-8", "gpe-9", "gpe-10";
+		samsung,pin-function = <2>;
+	};
+
+	sd1_cmd: sd1-cmd {
+		samsung,pins = "gpl-8";
+		samsung,pin-function = <2>;
+	};
+
+	sd1_clk: sd1-clk {
+		samsung,pins = "gpl-9";
+		samsung,pin-function = <2>;
+	};
+
+	sd1_bus1: sd1-bus1 {
+		samsung,pins = "gpl-0";
+		samsung,pin-function = <2>;
+	};
+
+	sd1_bus4: sd1-bus4 {
+		samsung,pins = "gpl-1", "gpl-2", "gpl-3";
+		samsung,pin-function = <2>;
+	};
+};

arch/arm/boot/dts/s3c2416-smdk2416.dts

+/*
+ * SAMSUNG SMDK2416 board device tree source
+ *
+ * Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+/include/ "s3c2416.dtsi"
+
+/ {
+	model = "SMDK2416";
+	compatible = "samsung,s3c2416";
+
+	memory {
+		reg =  <0x30000000 0x4000000>;
+	};
+
+	serial@50000000 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart0_data>, <&uart0_fctl>;
+	};
+
+	serial@50004000 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart1_data>, <&uart1_fctl>;
+	};
+
+	serial@50008000 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart2_data>;
+	};
+
+	serial@5000C000 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart3_data>;
+	};
+
+	watchdog@53000000 {
+		status = "okay";
+	};
+
+	rtc@57000000 {
+		status = "okay";
+	};
+
+	sdhci@4AC00000 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd0_clk>, <&sd0_cmd>,
+				<&sd0_bus1>, <&sd0_bus4>;
+		bus-width = <4>;
+		cd-gpios = <&gpf 1 0>;
+		cd-inverted;
+		status = "okay";
+	};
+
+	sdhci@4A800000 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd1_clk>, <&sd1_cmd>,
+				<&sd1_bus1>, <&sd1_bus4>;
+		bus-width = <4>;
+		broken-cd;
+		status = "okay";
+	};
+};

arch/arm/boot/dts/s3c2416.dtsi

+/*
+ * Samsung's S3C2416 SoC device tree source
+ *
+ * Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/include/ "s3c24xx.dtsi"
+/include/ "s3c2416-pinctrl.dtsi"
+
+/ {
+	model = "Samsung S3C2416 SoC";
+	compatible = "samsung,s3c2416";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu {
+			compatible = "arm,arm926ejs";
+		};
+	};
+
+	interrupt-controller@4a000000 {
+		compatible = "samsung,s3c2416-irq";
+	};
+
+	pinctrl@56000000 {
+		compatible = "samsung,s3c2416-pinctrl";
+	};
+
+	serial@50000000 {
+		compatible = "samsung,s3c2440-uart";
+	};
+
+	serial@50004000 {
+		compatible = "samsung,s3c2440-uart";
+	};
+
+	serial@50008000 {
+		compatible = "samsung,s3c2440-uart";
+	};
+
+	serial@5000C000 {
+		compatible = "samsung,s3c2440-uart";
+		reg = <0x5000C000 0x4000>;
+		interrupts = <1 18 24 4>, <1 18 25 4>;
+		status = "disabled";
+	};
+
+	sdhci@4AC00000 {
+		compatible = "samsung,s3c6410-sdhci";
+		reg = <0x4AC00000 0x100>;
+		interrupts = <0 0 21 3>;
+		status = "disabled";
+	};
+
+	sdhci@4A800000 {
+		compatible = "samsung,s3c6410-sdhci";
+		reg = <0x4A800000 0x100>;
+		interrupts = <0 0 20 3>;
+		status = "disabled";
+	};
+
+	watchdog@53000000 {
+		interrupts = <1 9 27 3>;
+	};
+
+	rtc@57000000 {
+		compatible = "samsung,s3c2416-rtc";
+	};
+
+	i2c@54000000 {
+		compatible = "samsung,s3c2440-i2c";
+	};
+};

arch/arm/boot/dts/s3c24xx.dtsi

+/*
+ * Samsung's S3C24XX family device tree source
+ *
+ * Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	compatible = "samsung,s3c24xx";
+	interrupt-parent = <&intc>;
+
+	aliases {
+		pinctrl0 = &pinctrl_0;
+	};
+
+	intc:interrupt-controller@4a000000 {
+		compatible = "samsung,s3c2410-irq";
+		reg = <0x4a000000 0x100>;
+		interrupt-controller;
+		#interrupt-cells = <4>;
+	};
+
+	pinctrl_0: pinctrl@56000000 {
+		reg = <0x56000000 0x1000>;
+
+		wakeup-interrupt-controller {
+			compatible = "samsung,s3c2410-wakeup-eint";
+			interrupts = <0 0 0 3>,
+				     <0 0 1 3>,
+				     <0 0 2 3>,
+				     <0 0 3 3>,
+				     <0 0 4 4>,
+				     <0 0 5 4>;
+		};
+	};
+
+	timer@51000000 {
+		compatible = "samsung,s3c2410-pwm";
+		reg = <0x51000000 0x1000>;
+		interrupts = <0 0 10 3>, <0 0 11 3>, <0 0 12 3>, <0 0 13 3>, <0 0 14 3>;
+		#pwm-cells = <4>;
+	};
+
+	serial@50000000 {
+		compatible = "samsung,s3c2410-uart";
+		reg = <0x50000000 0x4000>;
+		interrupts = <1 28 0 4>, <1 28 1 4>;
+		status = "disabled";
+	};
+
+	serial@50004000 {
+		compatible = "samsung,s3c2410-uart";
+		reg = <0x50004000 0x4000>;
+		interrupts = <1 23 3 4>, <1 23 4 4>;
+		status = "disabled";
+	};
+
+	serial@50008000 {
+		compatible = "samsung,s3c2410-uart";
+		reg = <0x50008000 0x4000>;
+		interrupts = <1 15 6 4>, <1 15 7 4>;
+		status = "disabled";
+	};
+
+	watchdog@53000000 {
+		compatible = "samsung,s3c2410-wdt";
+		reg = <0x53000000 0x100>;
+		interrupts = <0 0 9 3>;
+		status = "disabled";
+	};
+
+	rtc@57000000 {
+		compatible = "samsung,s3c2410-rtc";
+		reg = <0x57000000 0x100>;
+		interrupts = <0 0 30 3>, <0 0 8 3>;
+		status = "disabled";
+	};
+
+	i2c@54000000 {
+		compatible = "samsung,s3c2410-i2c";
+		reg = <0x54000000 0x100>;
+		interrupts = <0 0 27 3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+};

arch/arm/mach-s3c24xx/Kconfig

@@ -486,6 +486,18 @@ config MACH_SMDK2416
 	help
 	  Say Y here if you are using an SMDK2416
 
+config MACH_S3C2416_DT
+	bool "Samsung S3C2416 machine using devicetree"
+	select CLKSRC_OF
+	select USE_OF
+	select PINCTRL
+	select PINCTRL_S3C24XX
+	help
+	  Machine support for Samsung S3C2416 machines with device tree enabled.
+	  Select this if a fdt blob is available for the S3C2416 SoC based board.
+	  Note: This is under development and not all peripherals can be supported
+	  with this machine file.
+
 endif	# CPU_S3C2416
 
 if CPU_S3C2440

arch/arm/mach-s3c24xx/Makefile

@@ -79,6 +79,7 @@ obj-$(CONFIG_MACH_SMDK2413)		+= mach-smdk2413.o
 obj-$(CONFIG_MACH_VSTMS)		+= mach-vstms.o
 
 obj-$(CONFIG_MACH_SMDK2416)		+= mach-smdk2416.o
+obj-$(CONFIG_MACH_S3C2416_DT)		+= mach-s3c2416-dt.o
 
 obj-$(CONFIG_MACH_ANUBIS)		+= mach-anubis.o
 obj-$(CONFIG_MACH_AT2440EVB)		+= mach-at2440evb.o

arch/arm/mach-s3c24xx/mach-s3c2416-dt.c

+/*
+ * Samsung's S3C2416 flattened device tree enabled machine
+ *
+ * Copyright (c) 2012 Heiko Stuebner <heiko@sntech.de>
+ *
+ * based on mach-exynos/mach-exynos4-dt.c
+ *
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2010-2011 Linaro Ltd.
+ *		www.linaro.org
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/clocksource.h>
+#include <linux/irqchip.h>
+#include <linux/of_platform.h>
+#include <linux/serial_core.h>
+
+#include <asm/mach/arch.h>
+#include <mach/map.h>
+
+#include <plat/cpu.h>
+#include <plat/pm.h>
+#include <plat/regs-serial.h>
+
+#include "common.h"
+
+/*
+ * The following lookup table is used to override device names when devices
+ * are registered from device tree. This is temporarily added to enable
+ * device tree support addition for the S3C2416 architecture.
+ *
+ * For drivers that require platform data to be provided from the machine
+ * file, a platform data pointer can also be supplied along with the
+ * devices names. Usually, the platform data elements that cannot be parsed
+ * from the device tree by the drivers (example: function pointers) are
+ * supplied. But it should be noted that this is a temporary mechanism and
+ * at some point, the drivers should be capable of parsing all the platform
+ * data from the device tree.
+ */
+static const struct of_dev_auxdata s3c2416_auxdata_lookup[] __initconst = {
+	OF_DEV_AUXDATA("samsung,s3c2440-uart", S3C24XX_PA_UART,
+				"s3c2440-uart.0", NULL),
+	OF_DEV_AUXDATA("samsung,s3c2440-uart", S3C24XX_PA_UART + 0x4000,
+				"s3c2440-uart.1", NULL),
+	OF_DEV_AUXDATA("samsung,s3c2440-uart", S3C24XX_PA_UART + 0x8000,
+				"s3c2440-uart.2", NULL),
+	OF_DEV_AUXDATA("samsung,s3c2440-uart", S3C24XX_PA_UART + 0xC000,
+				"s3c2440-uart.3", NULL),
+	OF_DEV_AUXDATA("samsung,s3c6410-sdhci", S3C_PA_HSMMC0,
+				"s3c-sdhci.0", NULL),
+	OF_DEV_AUXDATA("samsung,s3c6410-sdhci", S3C_PA_HSMMC1,
+				"s3c-sdhci.1", NULL),
+	OF_DEV_AUXDATA("samsung,s3c2440-i2c", S3C_PA_IIC,
+				"s3c2440-i2c.0", NULL),
+	{},
+};
+
+static void __init s3c2416_dt_map_io(void)
+{
+	s3c24xx_init_io(NULL, 0);
+	s3c24xx_init_clocks(12000000);
+}
+
+static void __init s3c2416_dt_machine_init(void)
+{
+	of_platform_populate(NULL, of_default_bus_match_table,
+				s3c2416_auxdata_lookup, NULL);
+
+	s3c_pm_init();
+}
+
+static char const *s3c2416_dt_compat[] __initdata = {
+	"samsung,s3c2416",
+	"samsung,s3c2450",
+	NULL
+};
+
+DT_MACHINE_START(S3C2416_DT, "Samsung S3C2416 (Flattened Device Tree)")
+	/* Maintainer: Heiko Stuebner <heiko@sntech.de> */
+	.dt_compat	= s3c2416_dt_compat,
+	.map_io		= s3c2416_dt_map_io,
+	.init_irq	= irqchip_init,
+	.init_machine	= s3c2416_dt_machine_init,
+	 .init_time	= clocksource_of_init,
+	.restart	= s3c2416_restart,
+MACHINE_END

drivers/clk/samsung/clk-exynos4.c

@@ -151,7 +151,7 @@ enum exynos4_clks {
 	sclk_audio1, sclk_audio2, sclk_spdif, sclk_spi0, sclk_spi1, sclk_spi2,
 	sclk_slimbus, sclk_fimd1, sclk_mipi1, sclk_pcm1, sclk_pcm2, sclk_i2s1,
 	sclk_i2s2, sclk_mipihsi, sclk_mfc, sclk_pcm0, sclk_g3d, sclk_pwm_isp,
-	sclk_spi0_isp, sclk_spi1_isp, sclk_uart_isp,
+	sclk_spi0_isp, sclk_spi1_isp, sclk_uart_isp, sclk_fimg2d,
 
 	/* gate clocks */
 	fimc0 = 256, fimc1, fimc2, fimc3, csis0, csis1, jpeg, smmu_fimc0,
@@ -484,6 +484,9 @@ struct samsung_mux_clock exynos4x12_mux_clks[] __initdata = {
 	MUX(none, "mout_spi0_isp", group1_p4x12, E4X12_SRC_ISP, 4, 4),
 	MUX(none, "mout_spi1_isp", group1_p4x12, E4X12_SRC_ISP, 8, 4),
 	MUX(none, "mout_uart_isp", group1_p4x12, E4X12_SRC_ISP, 12, 4),
+	MUX(none, "mout_g2d0", sclk_ampll_p4210, SRC_DMC, 20, 1),
+	MUX(none, "mout_g2d1", sclk_evpll_p, SRC_DMC, 24, 1),
+	MUX(none, "mout_g2d", mout_g2d_p, SRC_DMC, 28, 1),
 };
 
 /* list of divider clocks supported in all exynos4 soc's */
@@ -552,7 +555,7 @@ struct samsung_div_clock exynos4_div_clks[] __initdata = {
 /* list of divider clocks supported in exynos4210 soc */
 struct samsung_div_clock exynos4210_div_clks[] __initdata = {
 	DIV(aclk200, "aclk200", "mout_aclk200", DIV_TOP, 0, 3),
-	DIV(none, "div_g2d", "mout_g2d", DIV_IMAGE, 0, 4),
+	DIV(sclk_fimg2d, "sclk_fimg2d", "mout_g2d", DIV_IMAGE, 0, 4),
 	DIV(none, "div_fimd1", "mout_fimd1", E4210_DIV_LCD1, 0, 4),
 	DIV(none, "div_mipi1", "mout_mipi1", E4210_DIV_LCD1, 16, 4),
 	DIV(none, "div_sata", "mout_sata", DIV_FSYS0, 20, 4),
@@ -582,6 +585,7 @@ struct samsung_div_clock exynos4x12_div_clks[] __initdata = {
 	DIV(none, "div_mpwm", "div_isp1", E4X12_DIV_ISP1, 0, 3),
 	DIV(div_mcuisp0, "div_mcuisp0", "aclk400_mcuisp", E4X12_DIV_ISP1, 4, 3),
 	DIV(div_mcuisp1, "div_mcuisp1", "div_mcuisp0", E4X12_DIV_ISP1, 8, 3),
+	DIV(sclk_fimg2d, "sclk_fimg2d", "mout_g2d", DIV_DMC1, 0, 4),
 };
 
 /* list of gate clocks supported in all exynos4 soc's */
@@ -909,6 +913,7 @@ struct samsung_gate_clock exynos4x12_gate_clks[] __initdata = {
 			CLK_IGNORE_UNUSED, 0),
 	GATE(spi1_isp, "spi1_isp", "aclk200", E4X12_GATE_ISP1, 13,
 			CLK_IGNORE_UNUSED, 0),
+	GATE(g2d, "g2d", "aclk200", GATE_IP_DMC, 23, 0, 0),
 };
 
 /*