ARM64: dts: meson-gxbb: add MMC support

Add binding and basic support for the SD/eMMC controller on Amlogic
S905/GXBB devices.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
[narmstrong: added nodes for GX, enabled SDIO on P20x]
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

arch/arm64/boot/dts/amlogic/meson-gx.dtsi

@@ -203,6 +203,27 @@
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
+
+			sd_emmc_a: mmc@70000 {
+				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
+				reg = <0x0 0x70000 0x0 0x2000>;
+				interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
+				status = "disabled";
+			};
+
+			sd_emmc_b: mmc@72000 {
+				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
+				reg = <0x0 0x72000 0x0 0x2000>;
+				interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
+				status = "disabled";
+			};
+
+			sd_emmc_c: mmc@74000 {
+				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
+				reg = <0x0 0x74000 0x0 0x2000>;
+				interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
+				status = "disabled";
+			};
 		};
 	};
 };

arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts

@@ -85,6 +85,56 @@
 			default-state = "off";
 		};
 	};
+
+	tflash_vdd: regulator-tflash_vdd {
+		/*
+		 * signal name from schematics: TFLASH_VDD_EN
+		 */
+		compatible = "regulator-fixed";
+
+		regulator-name = "TFLASH_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio_ao GPIOAO_12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	tf_io: gpio-regulator-tf_io {
+		compatible = "regulator-gpio";
+
+		regulator-name = "TF_IO";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		/*
+		 * signal name from schematics: TF_3V3N_1V8_EN
+		 */
+		gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+
+		states = <3300000 0
+			  1800000 1>;
+	};
+
+	vcc1v8: regulator-vcc1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vcc3v3: regulator-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
 };
 
 &uart_AO {
@@ -127,3 +177,41 @@
 &usb1 {
 	status = "okay";
 };
+
+/* SD */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&tflash_vdd>;
+	vqmmc-supply = <&tf_io>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <8>;
+	cap-sd-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc3v3>;
+	vqmmc-supply = <&vcc1v8>;
+};

arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi

@@ -70,6 +70,47 @@
 		gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
+
+	vddio_card: gpio-regulator {
+		compatible = "regulator-gpio";
+
+		regulator-name = "VDDIO_CARD";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+
+		/* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
+		states = <1800000 0
+			  3300000 1>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
 };
 
 /* This UART is brought out to the DB9 connector */
@@ -107,3 +148,60 @@
 &usb1 {
 	status = "okay";
 };
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_card>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <8>;
+	cap-sd-highspeed;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};

arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi

@@ -349,7 +349,8 @@
 			mux {
 				groups = "emmc_nand_d07",
 				       "emmc_cmd",
-				       "emmc_clk";
+				       "emmc_clk",
+				       "emmc_ds";
 				function = "emmc";
 			};
 		};
@@ -545,3 +546,24 @@
 		#mbox-cells = <1>;
 	};
 };
+
+&sd_emmc_a {
+	clocks = <&clkc CLKID_SD_EMMC_A>,
+		 <&xtal>,
+		 <&clkc CLKID_FCLK_DIV2>;
+	clock-names = "core", "clkin0", "clkin1";
+};
+
+&sd_emmc_b {
+	clocks = <&clkc CLKID_SD_EMMC_B>,
+		 <&xtal>,
+		 <&clkc CLKID_FCLK_DIV2>;
+	clock-names = "core", "clkin0", "clkin1";
+};
+
+&sd_emmc_c {
+	clocks = <&clkc CLKID_SD_EMMC_C>,
+		 <&xtal>,
+		 <&clkc CLKID_FCLK_DIV2>;
+	clock-names = "core", "clkin0", "clkin1";
+};