提交 ebe19a4e 编写于 作者: D Dale Farnsworth 提交者: Jeff Garzik

[PATCH] mv643xx_eth: Remove BIT0-BIT31 #defines

Now that the BIT0-BIT31 defines are no longer used by mv643xx_eth.c,
remove them from mv643xx_eth.h.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
上级 f78fb474
......@@ -9,43 +9,6 @@
#include <linux/mv643xx.h>
#define BIT0 0x00000001
#define BIT1 0x00000002
#define BIT2 0x00000004
#define BIT3 0x00000008
#define BIT4 0x00000010
#define BIT5 0x00000020
#define BIT6 0x00000040
#define BIT7 0x00000080
#define BIT8 0x00000100
#define BIT9 0x00000200
#define BIT10 0x00000400
#define BIT11 0x00000800
#define BIT12 0x00001000
#define BIT13 0x00002000
#define BIT14 0x00004000
#define BIT15 0x00008000
#define BIT16 0x00010000
#define BIT17 0x00020000
#define BIT18 0x00040000
#define BIT19 0x00080000
#define BIT20 0x00100000
#define BIT21 0x00200000
#define BIT22 0x00400000
#define BIT23 0x00800000
#define BIT24 0x01000000
#define BIT25 0x02000000
#define BIT26 0x04000000
#define BIT27 0x08000000
#define BIT28 0x10000000
#define BIT29 0x20000000
#define BIT30 0x40000000
#define BIT31 0x80000000
/*
* The first part is the high level driver of the gigE ethernet ports.
*/
/* Checksum offload for Tx works for most packets, but
* fails if previous packet sent did not use hw csum
*/
......@@ -148,88 +111,71 @@
#define ETH_MIB_LATE_COLLISION 0x7c
/* Port serial status reg (PSR) */
#define ETH_INTERFACE_GMII_MII 0
#define ETH_INTERFACE_PCM BIT0
#define ETH_LINK_IS_DOWN 0
#define ETH_LINK_IS_UP BIT1
#define ETH_PORT_AT_HALF_DUPLEX 0
#define ETH_PORT_AT_FULL_DUPLEX BIT2
#define ETH_RX_FLOW_CTRL_DISABLED 0
#define ETH_RX_FLOW_CTRL_ENBALED BIT3
#define ETH_GMII_SPEED_100_10 0
#define ETH_GMII_SPEED_1000 BIT4
#define ETH_MII_SPEED_10 0
#define ETH_MII_SPEED_100 BIT5
#define ETH_NO_TX 0
#define ETH_TX_IN_PROGRESS BIT7
#define ETH_BYPASS_NO_ACTIVE 0
#define ETH_BYPASS_ACTIVE BIT8
#define ETH_PORT_NOT_AT_PARTITION_STATE 0
#define ETH_PORT_AT_PARTITION_STATE BIT9
#define ETH_PORT_TX_FIFO_NOT_EMPTY 0
#define ETH_PORT_TX_FIFO_EMPTY BIT10
#define ETH_DEFAULT_RX_BPDU_QUEUE_3 (BIT23 | BIT22)
#define ETH_DEFAULT_RX_BPDU_QUEUE_4 BIT24
#define ETH_DEFAULT_RX_BPDU_QUEUE_5 (BIT24 | BIT22)
#define ETH_DEFAULT_RX_BPDU_QUEUE_6 (BIT24 | BIT23)
#define ETH_DEFAULT_RX_BPDU_QUEUE_7 (BIT24 | BIT23 | BIT22)
#define ETH_INTERFACE_PCM 0x00000001
#define ETH_LINK_IS_UP 0x00000002
#define ETH_PORT_AT_FULL_DUPLEX 0x00000004
#define ETH_RX_FLOW_CTRL_ENABLED 0x00000008
#define ETH_GMII_SPEED_1000 0x00000010
#define ETH_MII_SPEED_100 0x00000020
#define ETH_TX_IN_PROGRESS 0x00000080
#define ETH_BYPASS_ACTIVE 0x00000100
#define ETH_PORT_AT_PARTITION_STATE 0x00000200
#define ETH_PORT_TX_FIFO_EMPTY 0x00000400
/* SMI reg */
#define ETH_SMI_BUSY BIT28 /* 0 - Write, 1 - Read */
#define ETH_SMI_READ_VALID BIT27 /* 0 - Write, 1 - Read */
#define ETH_SMI_OPCODE_WRITE 0 /* Completion of Read operation */
#define ETH_SMI_OPCODE_READ BIT26 /* Operation is in progress */
#define ETH_SMI_BUSY 0x10000000 /* 0 - Write, 1 - Read */
#define ETH_SMI_READ_VALID 0x08000000 /* 0 - Write, 1 - Read */
#define ETH_SMI_OPCODE_WRITE 0 /* Completion of Read */
#define ETH_SMI_OPCODE_READ 0x04000000 /* Operation is in progress */
/* Interrupt Cause Register Bit Definitions */
/* SDMA command status fields macros */
/* Tx & Rx descriptors status */
#define ETH_ERROR_SUMMARY (BIT0)
#define ETH_ERROR_SUMMARY 0x00000001
/* Tx & Rx descriptors command */
#define ETH_BUFFER_OWNED_BY_DMA (BIT31)
#define ETH_BUFFER_OWNED_BY_DMA 0x80000000
/* Tx descriptors status */
#define ETH_LC_ERROR (0 )
#define ETH_UR_ERROR (BIT1 )
#define ETH_RL_ERROR (BIT2 )
#define ETH_LLC_SNAP_FORMAT (BIT9 )
#define ETH_LC_ERROR 0
#define ETH_UR_ERROR 0x00000002
#define ETH_RL_ERROR 0x00000004
#define ETH_LLC_SNAP_FORMAT 0x00000200
/* Rx descriptors status */
#define ETH_CRC_ERROR (0 )
#define ETH_OVERRUN_ERROR (BIT1 )
#define ETH_MAX_FRAME_LENGTH_ERROR (BIT2 )
#define ETH_RESOURCE_ERROR ((BIT2 | BIT1))
#define ETH_VLAN_TAGGED (BIT19)
#define ETH_BPDU_FRAME (BIT20)
#define ETH_TCP_FRAME_OVER_IP_V_4 (0 )
#define ETH_UDP_FRAME_OVER_IP_V_4 (BIT21)
#define ETH_OTHER_FRAME_TYPE (BIT22)
#define ETH_LAYER_2_IS_ETH_V_2 (BIT23)
#define ETH_FRAME_TYPE_IP_V_4 (BIT24)
#define ETH_FRAME_HEADER_OK (BIT25)
#define ETH_RX_LAST_DESC (BIT26)
#define ETH_RX_FIRST_DESC (BIT27)
#define ETH_UNKNOWN_DESTINATION_ADDR (BIT28)
#define ETH_RX_ENABLE_INTERRUPT (BIT29)
#define ETH_LAYER_4_CHECKSUM_OK (BIT30)
#define ETH_OVERRUN_ERROR 0x00000002
#define ETH_MAX_FRAME_LENGTH_ERROR 0x00000004
#define ETH_RESOURCE_ERROR 0x00000006
#define ETH_VLAN_TAGGED 0x00080000
#define ETH_BPDU_FRAME 0x00100000
#define ETH_UDP_FRAME_OVER_IP_V_4 0x00200000
#define ETH_OTHER_FRAME_TYPE 0x00400000
#define ETH_LAYER_2_IS_ETH_V_2 0x00800000
#define ETH_FRAME_TYPE_IP_V_4 0x01000000
#define ETH_FRAME_HEADER_OK 0x02000000
#define ETH_RX_LAST_DESC 0x04000000
#define ETH_RX_FIRST_DESC 0x08000000
#define ETH_UNKNOWN_DESTINATION_ADDR 0x10000000
#define ETH_RX_ENABLE_INTERRUPT 0x20000000
#define ETH_LAYER_4_CHECKSUM_OK 0x40000000
/* Rx descriptors byte count */
#define ETH_FRAME_FRAGMENTED (BIT2)
#define ETH_FRAME_FRAGMENTED 0x00000004
/* Tx descriptors command */
#define ETH_LAYER_4_CHECKSUM_FIRST_DESC (BIT10)
#define ETH_FRAME_SET_TO_VLAN (BIT15)
#define ETH_TCP_FRAME (0 )
#define ETH_UDP_FRAME (BIT16)
#define ETH_GEN_TCP_UDP_CHECKSUM (BIT17)
#define ETH_GEN_IP_V_4_CHECKSUM (BIT18)
#define ETH_ZERO_PADDING (BIT19)
#define ETH_TX_LAST_DESC (BIT20)
#define ETH_TX_FIRST_DESC (BIT21)
#define ETH_GEN_CRC (BIT22)
#define ETH_TX_ENABLE_INTERRUPT (BIT23)
#define ETH_AUTO_MODE (BIT30)
#define ETH_LAYER_4_CHECKSUM_FIRST_DESC 0x00000400
#define ETH_FRAME_SET_TO_VLAN 0x00008000
#define ETH_UDP_FRAME 0x00010000
#define ETH_GEN_TCP_UDP_CHECKSUM 0x00020000
#define ETH_GEN_IP_V_4_CHECKSUM 0x00040000
#define ETH_ZERO_PADDING 0x00080000
#define ETH_TX_LAST_DESC 0x00100000
#define ETH_TX_FIRST_DESC 0x00200000
#define ETH_GEN_CRC 0x00400000
#define ETH_TX_ENABLE_INTERRUPT 0x00800000
#define ETH_AUTO_MODE 0x40000000
#define ETH_TX_IHL_SHIFT 11
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册