Merge drm-upstream/drm-next into drm-misc-next

Pull in the malidp writeback implementation for further work on writeback in drm-misc-next.
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.com>

Documentation/admin-guide/pm/intel_pstate.rst

@@ -324,8 +324,7 @@ Global Attributes
 
 ``intel_pstate`` exposes several global attributes (files) in ``sysfs`` to
 control its functionality at the system level.  They are located in the
-``/sys/devices/system/cpu/cpufreq/intel_pstate/`` directory and affect all
-CPUs.
+``/sys/devices/system/cpu/intel_pstate/`` directory and affect all CPUs.
 
 Some of them are not present if the ``intel_pstate=per_cpu_perf_limits``
 argument is passed to the kernel in the command line.
@@ -379,6 +378,17 @@ argument is passed to the kernel in the command line.
 	but it affects the maximum possible value of per-policy P-state	limits
 	(see `Interpretation of Policy Attributes`_ below for details).
 
+``hwp_dynamic_boost``
+	This attribute is only present if ``intel_pstate`` works in the
+	`active mode with the HWP feature enabled <Active Mode With HWP_>`_ in
+	the processor.  If set (equal to 1), it causes the minimum P-state limit
+	to be increased dynamically for a short time whenever a task previously
+	waiting on I/O is selected to run on a given logical CPU (the purpose
+	of this mechanism is to improve performance).
+
+	This setting has no effect on logical CPUs whose minimum P-state limit
+	is directly set to the highest non-turbo P-state or above it.
+
 .. _status_attr:
 
 ``status``

Documentation/devicetree/bindings/input/sprd,sc27xx-vibra.txt

+Spreadtrum SC27xx PMIC Vibrator
+
+Required properties:
+- compatible: should be "sprd,sc2731-vibrator".
+- reg: address of vibrator control register.
+
+Example :
+
+	sc2731_pmic: pmic@0 {
+		compatible = "sprd,sc2731";
+		reg = <0>;
+		spi-max-frequency = <26000000>;
+		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vibrator@eb4 {
+			compatible = "sprd,sc2731-vibrator";
+			reg = <0xeb4>;
+		};
+	};

Documentation/filesystems/Locking

@@ -441,8 +441,6 @@ prototypes:
 	int (*iterate) (struct file *, struct dir_context *);
 	int (*iterate_shared) (struct file *, struct dir_context *);
 	__poll_t (*poll) (struct file *, struct poll_table_struct *);
-	struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
-	__poll_t (*poll_mask) (struct file *, __poll_t);
 	long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
 	long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
 	int (*mmap) (struct file *, struct vm_area_struct *);
@@ -473,7 +471,7 @@ prototypes:
 };
 
 locking rules:
-	All except for ->poll_mask may block.
+	All may block.
 
 ->llseek() locking has moved from llseek to the individual llseek
 implementations.  If your fs is not using generic_file_llseek, you
@@ -505,9 +503,6 @@ in sys_read() and friends.
 the lease within the individual filesystem to record the result of the
 operation
 
-->poll_mask can be called with or without the waitqueue lock for the waitqueue
-returned from ->get_poll_head.
-
 --------------------------- dquot_operations -------------------------------
 prototypes:
 	int (*write_dquot) (struct dquot *);

Documentation/filesystems/vfs.txt

@@ -857,8 +857,6 @@ struct file_operations {
 	ssize_t (*write_iter) (struct kiocb *, struct iov_iter *);
 	int (*iterate) (struct file *, struct dir_context *);
 	__poll_t (*poll) (struct file *, struct poll_table_struct *);
-	struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
-	__poll_t (*poll_mask) (struct file *, __poll_t);
 	long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
 	long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
 	int (*mmap) (struct file *, struct vm_area_struct *);
@@ -903,17 +901,6 @@ otherwise noted.
 	activity on this file and (optionally) go to sleep until there
 	is activity. Called by the select(2) and poll(2) system calls
 
-  get_poll_head: Returns the struct wait_queue_head that callers can
-  wait on.  Callers need to check the returned events using ->poll_mask
-  once woken.  Can return NULL to indicate polling is not supported,
-  or any error code using the ERR_PTR convention to indicate that a
-  grave error occured and ->poll_mask shall not be called.
-
-  poll_mask: return the mask of EPOLL* values describing the file descriptor
-  state.  Called either before going to sleep on the waitqueue returned by
-  get_poll_head, or after it has been woken.  If ->get_poll_head and
-  ->poll_mask are implemented ->poll does not need to be implement.
-
   unlocked_ioctl: called by the ioctl(2) system call.
 
   compat_ioctl: called by the ioctl(2) system call when 32 bit system calls

Documentation/kbuild/kconfig-language.txt

@@ -430,6 +430,12 @@ This sets the config program's title bar if the config program chooses
 to use it. It should be placed at the top of the configuration, before any
 other statement.
 
+'#' Kconfig source file comment:
+
+An unquoted '#' character anywhere in a source file line indicates
+the beginning of a source file comment.  The remainder of that line
+is a comment.
+
 
 Kconfig hints
 -------------

Documentation/locking/ww-mutex-design.txt

-Wait/Wound Deadlock-Proof Mutex Design
+Wound/Wait Deadlock-Proof Mutex Design
 ======================================
 
 Please read mutex-design.txt first, as it applies to wait/wound mutexes too.
@@ -32,10 +32,26 @@ the oldest task) wins, and the one with the higher reservation id (i.e. the
 younger task) unlocks all of the buffers that it has already locked, and then
 tries again.
 
-In the RDBMS literature this deadlock handling approach is called wait/wound:
-The older tasks waits until it can acquire the contended lock. The younger tasks
-needs to back off and drop all the locks it is currently holding, i.e. the
-younger task is wounded.
+In the RDBMS literature, a reservation ticket is associated with a transaction.
+and the deadlock handling approach is called Wait-Die. The name is based on
+the actions of a locking thread when it encounters an already locked mutex.
+If the transaction holding the lock is younger, the locking transaction waits.
+If the transaction holding the lock is older, the locking transaction backs off
+and dies. Hence Wait-Die.
+There is also another algorithm called Wound-Wait:
+If the transaction holding the lock is younger, the locking transaction
+wounds the transaction holding the lock, requesting it to die.
+If the transaction holding the lock is older, it waits for the other
+transaction. Hence Wound-Wait.
+The two algorithms are both fair in that a transaction will eventually succeed.
+However, the Wound-Wait algorithm is typically stated to generate fewer backoffs
+compared to Wait-Die, but is, on the other hand, associated with more work than
+Wait-Die when recovering from a backoff. Wound-Wait is also a preemptive
+algorithm in that transactions are wounded by other transactions, and that
+requires a reliable way to pick up up the wounded condition and preempt the
+running transaction. Note that this is not the same as process preemption. A
+Wound-Wait transaction is considered preempted when it dies (returning
+-EDEADLK) following a wound.
 
 Concepts
 --------
@@ -47,18 +63,20 @@ Acquire context: To ensure eventual forward progress it is important the a task
 trying to acquire locks doesn't grab a new reservation id, but keeps the one it
 acquired when starting the lock acquisition. This ticket is stored in the
 acquire context. Furthermore the acquire context keeps track of debugging state
-to catch w/w mutex interface abuse.
+to catch w/w mutex interface abuse. An acquire context is representing a
+transaction.
 
 W/w class: In contrast to normal mutexes the lock class needs to be explicit for
-w/w mutexes, since it is required to initialize the acquire context.
+w/w mutexes, since it is required to initialize the acquire context. The lock
+class also specifies what algorithm to use, Wound-Wait or Wait-Die.
 
 Furthermore there are three different class of w/w lock acquire functions:
 
 * Normal lock acquisition with a context, using ww_mutex_lock.
 
-* Slowpath lock acquisition on the contending lock, used by the wounded task
-  after having dropped all already acquired locks. These functions have the
-  _slow postfix.
+* Slowpath lock acquisition on the contending lock, used by the task that just
+  killed its transaction after having dropped all already acquired locks.
+  These functions have the _slow postfix.
 
   From a simple semantics point-of-view the _slow functions are not strictly
   required, since simply calling the normal ww_mutex_lock functions on the
@@ -90,6 +108,12 @@ provided.
 Usage
 -----
 
+The algorithm (Wait-Die vs Wound-Wait) is chosen by using either
+DEFINE_WW_CLASS() (Wound-Wait) or DEFINE_WD_CLASS() (Wait-Die)
+As a rough rule of thumb, use Wound-Wait iff you
+expect the number of simultaneous competing transactions to be typically small,
+and you want to reduce the number of rollbacks.
+
 Three different ways to acquire locks within the same w/w class. Common
 definitions for methods #1 and #2:
 
@@ -220,7 +244,7 @@ mutexes are a natural fit for such a case for two reasons:
 
 Note that this approach differs in two important ways from the above methods:
 - Since the list of objects is dynamically constructed (and might very well be
-  different when retrying due to hitting the -EDEADLK wound condition) there's
+  different when retrying due to hitting the -EDEADLK die condition) there's
   no need to keep any object on a persistent list when it's not locked. We can
   therefore move the list_head into the object itself.
 - On the other hand the dynamic object list construction also means that the -EALREADY return
@@ -312,12 +336,23 @@ Design:
   We maintain the following invariants for the wait list:
   (1) Waiters with an acquire context are sorted by stamp order; waiters
       without an acquire context are interspersed in FIFO order.
-  (2) Among waiters with contexts, only the first one can have other locks
-      acquired already (ctx->acquired > 0). Note that this waiter may come
-      after other waiters without contexts in the list.
+  (2) For Wait-Die, among waiters with contexts, only the first one can have
+      other locks acquired already (ctx->acquired > 0). Note that this waiter
+      may come after other waiters without contexts in the list.
+
+  The Wound-Wait preemption is implemented with a lazy-preemption scheme:
+  The wounded status of the transaction is checked only when there is
+  contention for a new lock and hence a true chance of deadlock. In that
+  situation, if the transaction is wounded, it backs off, clears the
+  wounded status and retries. A great benefit of implementing preemption in
+  this way is that the wounded transaction can identify a contending lock to
+  wait for before restarting the transaction. Just blindly restarting the
+  transaction would likely make the transaction end up in a situation where
+  it would have to back off again.
 
   In general, not much contention is expected. The locks are typically used to
-  serialize access to resources for devices.
+  serialize access to resources for devices, and optimization focus should
+  therefore be directed towards the uncontended cases.
 
 Lockdep:
   Special care has been taken to warn for as many cases of api abuse

Documentation/networking/e100.rst

+==============================================================
 Linux* Base Driver for the Intel(R) PRO/100 Family of Adapters
 ==============================================================
 
@@ -86,83 +87,84 @@ Event Log Message Level:  The driver uses the message level flag to log events
 Additional Configurations
 =========================
 
-  Configuring the Driver on Different Distributions
-  -------------------------------------------------
+Configuring the Driver on Different Distributions
+-------------------------------------------------
 
-  Configuring a network driver to load properly when the system is started is
-  distribution dependent. Typically, the configuration process involves adding
-  an alias line to /etc/modprobe.d/*.conf as well as editing other system
-  startup scripts and/or configuration files.  Many popular Linux
-  distributions ship with tools to make these changes for you. To learn the
-  proper way to configure a network device for your system, refer to your
-  distribution documentation.  If during this process you are asked for the
-  driver or module name, the name for the Linux Base Driver for the Intel
-  PRO/100 Family of Adapters is e100.
+Configuring a network driver to load properly when the system is started
+is distribution dependent.  Typically, the configuration process involves
+adding an alias line to /etc/modprobe.d/*.conf as well as editing other
+system startup scripts and/or configuration files.  Many popular Linux
+distributions ship with tools to make these changes for you.  To learn
+the proper way to configure a network device for your system, refer to
+your distribution documentation.  If during this process you are asked
+for the driver or module name, the name for the Linux Base Driver for
+the Intel PRO/100 Family of Adapters is e100.
 
-  As an example, if you install the e100 driver for two PRO/100 adapters
-  (eth0 and eth1), add the following to a configuration file in /etc/modprobe.d/
+As an example, if you install the e100 driver for two PRO/100 adapters
+(eth0 and eth1), add the following to a configuration file in
+/etc/modprobe.d/::
 
        alias eth0 e100
        alias eth1 e100
 
-  Viewing Link Messages
-  ---------------------
-  In order to see link messages and other Intel driver information on your
-  console, you must set the dmesg level up to six. This can be done by
-  entering the following on the command line before loading the e100 driver::
-
-       dmesg -n 6
+Viewing Link Messages
+---------------------
 
-  If you wish to see all messages issued by the driver, including debug
-  messages, set the dmesg level to eight.
+In order to see link messages and other Intel driver information on your
+console, you must set the dmesg level up to six.  This can be done by
+entering the following on the command line before loading the e100
+driver::
 
-  NOTE: This setting is not saved across reboots.
+       dmesg -n 6
 
+If you wish to see all messages issued by the driver, including debug
+messages, set the dmesg level to eight.
 
-  ethtool
-  -------
+NOTE: This setting is not saved across reboots.
 
-  The driver utilizes the ethtool interface for driver configuration and
-  diagnostics, as well as displaying statistical information.  The ethtool
-  version 1.6 or later is required for this functionality.
+ethtool
+-------
 
-  The latest release of ethtool can be found from
-  https://www.kernel.org/pub/software/network/ethtool/
+The driver utilizes the ethtool interface for driver configuration and
+diagnostics, as well as displaying statistical information.  The ethtool
+version 1.6 or later is required for this functionality.
 
-  Enabling Wake on LAN* (WoL)
-  ---------------------------
-  WoL is provided through the ethtool* utility.  For instructions on enabling
-  WoL with ethtool, refer to the ethtool man page.
+The latest release of ethtool can be found from
+https://www.kernel.org/pub/software/network/ethtool/
 
-  WoL will be enabled on the system during the next shut down or reboot. For
-  this driver version, in order to enable WoL, the e100 driver must be
-  loaded when shutting down or rebooting the system.
+Enabling Wake on LAN* (WoL)
+---------------------------
+WoL is provided through the ethtool* utility.  For instructions on
+enabling WoL with ethtool, refer to the ethtool man page.  WoL will be
+enabled on the system during the next shut down or reboot.  For this
+driver version, in order to enable WoL, the e100 driver must be loaded
+when shutting down or rebooting the system.
 
-  NAPI
-  ----
+NAPI
+----
 
-  NAPI (Rx polling mode) is supported in the e100 driver.
+NAPI (Rx polling mode) is supported in the e100 driver.
 
-  See https://wiki.linuxfoundation.org/networking/napi for more information
-  on NAPI.
+See https://wiki.linuxfoundation.org/networking/napi for more
+information on NAPI.
 
-  Multiple Interfaces on Same Ethernet Broadcast Network
-  ------------------------------------------------------
+Multiple Interfaces on Same Ethernet Broadcast Network
+------------------------------------------------------
 
-  Due to the default ARP behavior on Linux, it is not possible to have
-  one system on two IP networks in the same Ethernet broadcast domain
-  (non-partitioned switch) behave as expected. All Ethernet interfaces
-  will respond to IP traffic for any IP address assigned to the system.
-  This results in unbalanced receive traffic.
+Due to the default ARP behavior on Linux, it is not possible to have one
+system on two IP networks in the same Ethernet broadcast domain
+(non-partitioned switch) behave as expected.  All Ethernet interfaces
+will respond to IP traffic for any IP address assigned to the system.
+This results in unbalanced receive traffic.
 
-  If you have multiple interfaces in a server, either turn on ARP
-  filtering by
+If you have multiple interfaces in a server, either turn on ARP
+filtering by
 
-  (1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
-      (this only works if your kernel's version is higher than 2.4.5), or
+(1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+    (this only works if your kernel's version is higher than 2.4.5), or
 
-  (2) installing the interfaces in separate broadcast domains (either
-      in different switches or in a switch partitioned to VLANs).
+(2) installing the interfaces in separate broadcast domains (either
+    in different switches or in a switch partitioned to VLANs).
 
 
 Support

Documentation/networking/e1000.rst

+===========================================================
 Linux* Base Driver for Intel(R) Ethernet Network Connection
 ===========================================================
 
@@ -354,57 +355,58 @@ previously mentioned to force the adapter to the same speed and duplex.
 Additional Configurations
 =========================
 
-  Jumbo Frames
-  ------------
-  Jumbo Frames support is enabled by changing the MTU to a value larger than
-  the default of 1500.  Use the ifconfig command to increase the MTU size.
-  For example::
+Jumbo Frames
+------------
+Jumbo Frames support is enabled by changing the MTU to a value larger
+than the default of 1500.  Use the ifconfig command to increase the MTU
+size.  For example::
 
        ifconfig eth<x> mtu 9000 up
 
-  This setting is not saved across reboots.  It can be made permanent if
-  you add::
+This setting is not saved across reboots.  It can be made permanent if
+you add::
 
        MTU=9000
 
-   to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>.  This example
-   applies to the Red Hat distributions; other distributions may store this
-   setting in a different location.
+to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>.  This example
+applies to the Red Hat distributions; other distributions may store this
+setting in a different location.
+
+Notes: Degradation in throughput performance may be observed in some
+Jumbo frames environments.  If this is observed, increasing the
+application's socket buffer size and/or increasing the
+/proc/sys/net/ipv4/tcp_*mem entry values may help.  See the specific
+application manual and /usr/src/linux*/Documentation/
+networking/ip-sysctl.txt for more details.
 
-  Notes:
-  Degradation in throughput performance may be observed in some Jumbo frames
-  environments. If this is observed, increasing the application's socket buffer
-  size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values may help.
-  See the specific application manual and /usr/src/linux*/Documentation/
-  networking/ip-sysctl.txt for more details.
+- The maximum MTU setting for Jumbo Frames is 16110.  This value
+  coincides with the maximum Jumbo Frames size of 16128.
 
-  - The maximum MTU setting for Jumbo Frames is 16110.  This value coincides
-    with the maximum Jumbo Frames size of 16128.
+- Using Jumbo frames at 10 or 100 Mbps is not supported and may result
+  in poor performance or loss of link.
 
-  - Using Jumbo frames at 10 or 100 Mbps is not supported and may result in
-    poor performance or loss of link.
+- Adapters based on the Intel(R) 82542 and 82573V/E controller do not
+  support Jumbo Frames.  These correspond to the following product names:
+  Intel(R) PRO/1000 Gigabit Server Adapter Intel(R) PRO/1000 PM Network
+  Connection
 
-  - Adapters based on the Intel(R) 82542 and 82573V/E controller do not
-    support Jumbo Frames. These correspond to the following product names:
-     Intel(R) PRO/1000 Gigabit Server Adapter
-     Intel(R) PRO/1000 PM Network Connection
+ethtool
+-------
+The driver utilizes the ethtool interface for driver configuration and
+diagnostics, as well as displaying statistical information.  The ethtool
+version 1.6 or later is required for this functionality.
 
-  ethtool
-  -------
-  The driver utilizes the ethtool interface for driver configuration and
-  diagnostics, as well as displaying statistical information.  The ethtool
-  version 1.6 or later is required for this functionality.
+The latest release of ethtool can be found from
+https://www.kernel.org/pub/software/network/ethtool/
 
-  The latest release of ethtool can be found from
-  https://www.kernel.org/pub/software/network/ethtool/
+Enabling Wake on LAN* (WoL)
+---------------------------
+WoL is configured through the ethtool* utility.
 
-  Enabling Wake on LAN* (WoL)
-  ---------------------------
-  WoL is configured through the ethtool* utility.
+WoL will be enabled on the system during the next shut down or reboot.
+For this driver version, in order to enable WoL, the e1000 driver must be
+loaded when shutting down or rebooting the system.
 
-  WoL will be enabled on the system during the next shut down or reboot.
-  For this driver version, in order to enable WoL, the e1000 driver must be
-  loaded when shutting down or rebooting the system.
 
 Support
 =======

Documentation/networking/strparser.txt

@@ -48,7 +48,7 @@ void strp_pause(struct strparser *strp)
      Temporarily pause a stream parser. Message parsing is suspended
      and no new messages are delivered to the upper layer.
 
-void strp_pause(struct strparser *strp)
+void strp_unpause(struct strparser *strp)
 
      Unpause a paused stream parser.
 

Documentation/usb/gadget_configfs.txt

@@ -226,7 +226,7 @@ $ rm configs/<config name>.<number>/<function>
 where <config name>.<number> specify the configuration and <function> is
 a symlink to a function being removed from the configuration, e.g.:
 
-$ rm configfs/c.1/ncm.usb0
+$ rm configs/c.1/ncm.usb0
 
 ...
 ...

MAINTAINERS

@@ -2971,9 +2971,13 @@ N:	bcm585*
 N:	bcm586*
 N:	bcm88312
 N:	hr2
-F:	arch/arm64/boot/dts/broadcom/ns2*
+N:	stingray
+F:	arch/arm64/boot/dts/broadcom/northstar2/*
+F:	arch/arm64/boot/dts/broadcom/stingray/*
 F:	drivers/clk/bcm/clk-ns*
+F:	drivers/clk/bcm/clk-sr*
 F:	drivers/pinctrl/bcm/pinctrl-ns*
+F:	include/dt-bindings/clock/bcm-sr*
 
 BROADCOM KONA GPIO DRIVER
 M:	Ray Jui <rjui@broadcom.com>
@@ -5669,7 +5673,7 @@ F:	drivers/crypto/caam/
 F:	Documentation/devicetree/bindings/crypto/fsl-sec4.txt
 
 FREESCALE DIU FRAMEBUFFER DRIVER
-M:	Timur Tabi <timur@tabi.org>
+M:	Timur Tabi <timur@kernel.org>
 L:	linux-fbdev@vger.kernel.org
 S:	Maintained
 F:	drivers/video/fbdev/fsl-diu-fb.*
@@ -5769,7 +5773,7 @@ S:	Maintained
 F:	drivers/net/wan/fsl_ucc_hdlc*
 
 FREESCALE QUICC ENGINE UCC UART DRIVER
-M:	Timur Tabi <timur@tabi.org>
+M:	Timur Tabi <timur@kernel.org>
 L:	linuxppc-dev@lists.ozlabs.org
 S:	Maintained
 F:	drivers/tty/serial/ucc_uart.c
@@ -5793,7 +5797,7 @@ F:	drivers/net/ethernet/freescale/fs_enet/
 F:	include/linux/fs_enet_pd.h
 
 FREESCALE SOC SOUND DRIVERS
-M:	Timur Tabi <timur@tabi.org>
+M:	Timur Tabi <timur@kernel.org>
 M:	Nicolin Chen <nicoleotsuka@gmail.com>
 M:	Xiubo Li <Xiubo.Lee@gmail.com>
 R:	Fabio Estevam <fabio.estevam@nxp.com>
@@ -9882,6 +9886,7 @@ M:	Andrew Lunn <andrew@lunn.ch>
 M:	Vivien Didelot <vivien.didelot@savoirfairelinux.com>
 M:	Florian Fainelli <f.fainelli@gmail.com>
 S:	Maintained
+F:	Documentation/devicetree/bindings/net/dsa/
 F:	net/dsa/
 F:	include/net/dsa.h
 F:	include/linux/dsa/
@@ -11476,6 +11481,15 @@ W:	http://wireless.kernel.org/en/users/Drivers/p54
 S:	Obsolete
 F:	drivers/net/wireless/intersil/prism54/
 
+PROC FILESYSTEM
+R:	Alexey Dobriyan <adobriyan@gmail.com>
+L:	linux-kernel@vger.kernel.org
+L:	linux-fsdevel@vger.kernel.org
+S:	Maintained
+F:	fs/proc/
+F:	include/linux/proc_fs.h
+F:	tools/testing/selftests/proc/
+
 PROC SYSCTL
 M:	"Luis R. Rodriguez" <mcgrof@kernel.org>
 M:	Kees Cook <keescook@chromium.org>
@@ -11808,9 +11822,9 @@ F:  Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
 F:  drivers/cpufreq/qcom-cpufreq-kryo.c
 
 QUALCOMM EMAC GIGABIT ETHERNET DRIVER
-M:	Timur Tabi <timur@codeaurora.org>
+M:	Timur Tabi <timur@kernel.org>
 L:	netdev@vger.kernel.org
-S:	Supported
+S:	Maintained
 F:	drivers/net/ethernet/qualcomm/emac/
 
 QUALCOMM HEXAGON ARCHITECTURE

Makefile

@@ -2,7 +2,7 @@
 VERSION = 4
 PATCHLEVEL = 18
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc3
 NAME = Merciless Moray
 
 # *DOCUMENTATION*

arch/arm/Kconfig

@@ -1245,8 +1245,14 @@ config PCI
 	  VESA. If you have PCI, say Y, otherwise N.
 
 config PCI_DOMAINS
-	bool
+	bool "Support for multiple PCI domains"
 	depends on PCI
+	help
+	  Enable PCI domains kernel management. Say Y if your machine
+	  has a PCI bus hierarchy that requires more than one PCI
+	  domain (aka segment) to be correctly managed. Say N otherwise.
+
+	  If you don't know what to do here, say N.
 
 config PCI_DOMAINS_GENERIC
 	def_bool PCI_DOMAINS

arch/arm/boot/dts/armada-385-synology-ds116.dts

@@ -139,7 +139,7 @@
 					      3700 5
 					      3900 6
 					      4000 7>;
-			cooling-cells = <2>;
+			#cooling-cells = <2>;
 		};
 
 		gpio-leds {

arch/arm/boot/dts/bcm-cygnus.dtsi

@@ -216,7 +216,7 @@
 			reg = <0x18008000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};
@@ -245,7 +245,7 @@
 			reg = <0x1800b000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};
@@ -256,7 +256,7 @@
 
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 
 			linux,pci-domain = <0>;
 
@@ -278,10 +278,10 @@
 				compatible = "brcm,iproc-msi";
 				msi-controller;
 				interrupt-parent = <&gic>;
-				interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>,
-					     <GIC_SPI 97 IRQ_TYPE_NONE>,
-					     <GIC_SPI 98 IRQ_TYPE_NONE>,
-					     <GIC_SPI 99 IRQ_TYPE_NONE>;
+				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
@@ -291,7 +291,7 @@
 
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
 
 			linux,pci-domain = <1>;
 
@@ -313,10 +313,10 @@
 				compatible = "brcm,iproc-msi";
 				msi-controller;
 				interrupt-parent = <&gic>;
-				interrupts = <GIC_SPI 102 IRQ_TYPE_NONE>,
-					     <GIC_SPI 103 IRQ_TYPE_NONE>,
-					     <GIC_SPI 104 IRQ_TYPE_NONE>,
-					     <GIC_SPI 105 IRQ_TYPE_NONE>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 

arch/arm/boot/dts/bcm-hr2.dtsi

@@ -264,7 +264,7 @@
 			reg = <0x38000 0x50>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 95 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 		};
 
@@ -279,7 +279,7 @@
 			reg = <0x3b000 0x50>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 		};
 	};
@@ -300,7 +300,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 186 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <0>;
 
@@ -322,10 +322,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 182 IRQ_TYPE_NONE>,
-				     <GIC_SPI 183 IRQ_TYPE_NONE>,
-				     <GIC_SPI 184 IRQ_TYPE_NONE>,
-				     <GIC_SPI 185 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};
@@ -336,7 +336,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 192 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <1>;
 
@@ -358,10 +358,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>,
-				     <GIC_SPI 189 IRQ_TYPE_NONE>,
-				     <GIC_SPI 190 IRQ_TYPE_NONE>,
-				     <GIC_SPI 191 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};

arch/arm/boot/dts/bcm-nsp.dtsi

@@ -391,7 +391,7 @@
 			reg = <0x38000 0x50>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			dma-coherent;
 			status = "disabled";
@@ -496,7 +496,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <0>;
 
@@ -519,10 +519,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>,
-				     <GIC_SPI 128 IRQ_TYPE_NONE>,
-				     <GIC_SPI 129 IRQ_TYPE_NONE>,
-				     <GIC_SPI 130 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};
@@ -533,7 +533,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <1>;
 
@@ -556,10 +556,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 133 IRQ_TYPE_NONE>,
-				     <GIC_SPI 134 IRQ_TYPE_NONE>,
-				     <GIC_SPI 135 IRQ_TYPE_NONE>,
-				     <GIC_SPI 136 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};
@@ -570,7 +570,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <2>;
 
@@ -593,10 +593,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 139 IRQ_TYPE_NONE>,
-				     <GIC_SPI 140 IRQ_TYPE_NONE>,
-				     <GIC_SPI 141 IRQ_TYPE_NONE>,
-				     <GIC_SPI 142 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};

arch/arm/boot/dts/bcm5301x.dtsi

@@ -365,7 +365,7 @@
 	i2c0: i2c@18009000 {
 		compatible = "brcm,iproc-i2c";
 		reg = <0x18009000 0x50>;
-		interrupts = <GIC_SPI 121 IRQ_TYPE_NONE>;
+		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		clock-frequency = <100000>;

arch/arm/boot/dts/da850.dtsi

@@ -549,11 +549,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			reg = <0x226000 0x1000>;
-			interrupts = <42 IRQ_TYPE_EDGE_BOTH
-				43 IRQ_TYPE_EDGE_BOTH 44 IRQ_TYPE_EDGE_BOTH
-				45 IRQ_TYPE_EDGE_BOTH 46 IRQ_TYPE_EDGE_BOTH
-				47 IRQ_TYPE_EDGE_BOTH 48 IRQ_TYPE_EDGE_BOTH
-				49 IRQ_TYPE_EDGE_BOTH 50 IRQ_TYPE_EDGE_BOTH>;
+			interrupts = <42 43 44 45 46 47 48 49 50>;
 			ti,ngpio = <144>;
 			ti,davinci-gpio-unbanked = <0>;
 			status = "disabled";

arch/arm/boot/dts/imx6q.dtsi

@@ -90,7 +90,7 @@
 					clocks = <&clks IMX6Q_CLK_ECSPI5>,
 						 <&clks IMX6Q_CLK_ECSPI5>;
 					clock-names = "ipg", "per";
-					dmas = <&sdma 11 7 1>, <&sdma 12 7 2>;
+					dmas = <&sdma 11 8 1>, <&sdma 12 8 2>;
 					dma-names = "rx", "tx";
 					status = "disabled";
 				};

arch/arm/boot/dts/imx6sx.dtsi

@@ -1344,7 +1344,7 @@
 			ranges = <0x81000000 0 0          0x08f80000 0 0x00010000 /* downstream I/O */
 				  0x82000000 0 0x08000000 0x08000000 0 0x00f00000>; /* non-prefetchable memory */
 			num-lanes = <1>;
-			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;

arch/arm/boot/dts/socfpga.dtsi

@@ -748,13 +748,13 @@
 		nand0: nand@ff900000 {
 			#address-cells = <0x1>;
 			#size-cells = <0x1>;
-			compatible = "denali,denali-nand-dt";
+			compatible = "altr,socfpga-denali-nand";
 			reg = <0xff900000 0x100000>,
 			      <0xffb80000 0x10000>;
 			reg-names = "nand_data", "denali_reg";
 			interrupts = <0x0 0x90 0x4>;
 			dma-mask = <0xffffffff>;
-			clocks = <&nand_clk>;
+			clocks = <&nand_x_clk>;
 			status = "disabled";
 		};
 

arch/arm/boot/dts/socfpga_arria10.dtsi

@@ -593,8 +593,7 @@
 			#size-cells = <0>;
 			reg = <0xffda5000 0x100>;
 			interrupts = <0 102 4>;
-			num-chipselect = <4>;
-			bus-num = <0>;
+			num-cs = <4>;
 			/*32bit_access;*/
 			tx-dma-channel = <&pdma 16>;
 			rx-dma-channel = <&pdma 17>;
@@ -633,7 +632,7 @@
 		nand: nand@ffb90000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
-			compatible = "denali,denali-nand-dt", "altr,socfpga-denali-nand";
+			compatible = "altr,socfpga-denali-nand";
 			reg = <0xffb90000 0x72000>,
 			      <0xffb80000 0x10000>;
 			reg-names = "nand_data", "denali_reg";

arch/arm/common/Makefile

@@ -10,7 +10,7 @@ obj-$(CONFIG_DMABOUNCE)		+= dmabounce.o
 obj-$(CONFIG_SHARP_LOCOMO)	+= locomo.o
 obj-$(CONFIG_SHARP_PARAM)	+= sharpsl_param.o
 obj-$(CONFIG_SHARP_SCOOP)	+= scoop.o
-obj-$(CONFIG_SMP)		+= secure_cntvoff.o
+obj-$(CONFIG_CPU_V7)		+= secure_cntvoff.o
 obj-$(CONFIG_PCI_HOST_ITE8152)  += it8152.o
 obj-$(CONFIG_MCPM)		+= mcpm_head.o mcpm_entry.o mcpm_platsmp.o vlock.o
 CFLAGS_REMOVE_mcpm_entry.o	= -pg

arch/arm/mach-bcm/Kconfig

@@ -20,6 +20,7 @@ config ARCH_BCM_IPROC
 	select GPIOLIB
 	select ARM_AMBA
 	select PINCTRL
+	select PCI_DOMAINS if PCI
 	help
 	  This enables support for systems based on Broadcom IPROC architected SoCs.
 	  The IPROC complex contains one or more ARM CPUs along with common

arch/arm/mach-davinci/board-da850-evm.c

@@ -774,7 +774,7 @@ static struct gpiod_lookup_table mmc_gpios_table = {
 		GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_CD_PIN, "cd",
 			    GPIO_ACTIVE_LOW),
 		GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_WP_PIN, "wp",
-			    GPIO_ACTIVE_LOW),
+			    GPIO_ACTIVE_HIGH),
 	},
 };
 

arch/arm/mach-socfpga/Kconfig

@@ -10,6 +10,7 @@ menuconfig ARCH_SOCFPGA
 	select HAVE_ARM_SCU
 	select HAVE_ARM_TWD if SMP
 	select MFD_SYSCON
+	select PCI_DOMAINS if PCI
 
 if ARCH_SOCFPGA
 config SOCFPGA_SUSPEND

arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi

@@ -309,8 +309,7 @@
 			interrupts = <0 99 4>;
 			resets = <&rst SPIM0_RESET>;
 			reg-io-width = <4>;
-			num-chipselect = <4>;
-			bus-num = <0>;
+			num-cs = <4>;
 			status = "disabled";
 		};
 
@@ -322,8 +321,7 @@
 			interrupts = <0 100 4>;
 			resets = <&rst SPIM1_RESET>;
 			reg-io-width = <4>;
-			num-chipselect = <4>;
-			bus-num = <0>;
+			num-cs = <4>;
 			status = "disabled";
 		};
 

arch/arm64/boot/dts/amlogic/meson-axg-s400.dts

@@ -66,9 +66,22 @@
 
 &ethmac {
 	status = "okay";
-	phy-mode = "rgmii";
 	pinctrl-0 = <&eth_rgmii_y_pins>;
 	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rgmii";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy0: ethernet-phy@0 {
+			/* Realtek RTL8211F (0x001cc916) */
+			reg = <0>;
+			eee-broken-1000t;
+		};
+	};
 };
 
 &uart_A {

arch/arm64/boot/dts/amlogic/meson-axg.dtsi

@@ -132,7 +132,7 @@
 
 			sd_emmc_b: sd@5000 {
 				compatible = "amlogic,meson-axg-mmc";
-				reg = <0x0 0x5000 0x0 0x2000>;
+				reg = <0x0 0x5000 0x0 0x800>;
 				interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 				clocks = <&clkc CLKID_SD_EMMC_B>,
@@ -144,7 +144,7 @@
 
 			sd_emmc_c: mmc@7000 {
 				compatible = "amlogic,meson-axg-mmc";
-				reg = <0x0 0x7000 0x0 0x2000>;
+				reg = <0x0 0x7000 0x0 0x800>;
 				interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 				clocks = <&clkc CLKID_SD_EMMC_C>,

arch/arm64/boot/dts/amlogic/meson-gx.dtsi

@@ -35,6 +35,12 @@
 			no-map;
 		};
 
+		/* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
+		secmon_reserved_alt: secmon@5000000 {
+			reg = <0x0 0x05000000 0x0 0x300000>;
+			no-map;
+		};
+
 		linux,cma {
 			compatible = "shared-dma-pool";
 			reusable;
@@ -457,21 +463,21 @@
 
 			sd_emmc_a: mmc@70000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
-				reg = <0x0 0x70000 0x0 0x2000>;
+				reg = <0x0 0x70000 0x0 0x800>;
 				interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
 
 			sd_emmc_b: mmc@72000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
-				reg = <0x0 0x72000 0x0 0x2000>;
+				reg = <0x0 0x72000 0x0 0x800>;
 				interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
 
 			sd_emmc_c: mmc@74000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
-				reg = <0x0 0x74000 0x0 0x2000>;
+				reg = <0x0 0x74000 0x0 0x800>;
 				interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};

arch/arm64/boot/dts/amlogic/meson-gxl-mali.dtsi

@@ -6,7 +6,7 @@
 
 &apb {
 	mali: gpu@c0000 {
-		compatible = "amlogic,meson-gxbb-mali", "arm,mali-450";
+		compatible = "amlogic,meson-gxl-mali", "arm,mali-450";
 		reg = <0x0 0xc0000 0x0 0x40000>;
 		interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts

@@ -234,9 +234,6 @@
 
 	bus-width = <4>;
 	cap-sd-highspeed;
-	sd-uhs-sdr12;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
 	max-frequency = <100000000>;
 	disable-wp;
 

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi

@@ -189,3 +189,10 @@
 &usb0 {
 	status = "okay";
 };
+
+&usb2_phy0 {
+	/*
+	 * HDMI_5V is also used as supply for the USB VBUS.
+	 */
+	phy-supply = <&hdmi_5v>;
+};

arch/arm64/boot/dts/amlogic/meson-gxl.dtsi

@@ -13,14 +13,6 @@
 / {
 	compatible = "amlogic,meson-gxl";
 
-	reserved-memory {
-		/* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
-		secmon_reserved_alt: secmon@5000000 {
-			reg = <0x0 0x05000000 0x0 0x300000>;
-			no-map;
-		};
-	};
-
 	soc {
 		usb0: usb@c9000000 {
 			status = "disabled";

arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi

@@ -118,7 +118,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 281 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <0>;
 
@@ -149,7 +149,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 305 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <4>;
 
@@ -566,7 +566,7 @@
 			reg = <0x66080000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 394 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};
@@ -594,7 +594,7 @@
 			reg = <0x660b0000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 395 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};

arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts

@@ -43,6 +43,10 @@
 	enet-phy-lane-swap;
 };
 
+&sdio0 {
+	mmc-ddr-1_8v;
+};
+
 &uart2 {
 	status = "okay";
 };

arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts

@@ -42,3 +42,7 @@
 &gphy0 {
 	enet-phy-lane-swap;
 };
+
+&sdio0 {
+	mmc-ddr-1_8v;
+};

arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi

@@ -409,7 +409,7 @@
 			reg = <0x000b0000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 177 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};
@@ -453,7 +453,7 @@
 			reg = <0x000e0000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 178 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};

arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts

@@ -585,6 +585,8 @@
 	vmmc-supply = <&wlan_en>;
 	ti,non-removable;
 	non-removable;
+	cap-power-off-card;
+	keep-power-in-suspend;
 	#address-cells = <0x1>;
 	#size-cells = <0x0>;
 	status = "ok";

arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts

@@ -322,6 +322,8 @@
 		dwmmc_2: dwmmc2@f723f000 {
 			bus-width = <0x4>;
 			non-removable;
+			cap-power-off-card;
+			keep-power-in-suspend;
 			vmmc-supply = <&reg_vdd_3v3>;
 			mmc-pwrseq = <&wl1835_pwrseq>;
 

arch/arm64/boot/dts/marvell/armada-cp110.dtsi

@@ -149,7 +149,7 @@
 
 		CP110_LABEL(icu): interrupt-controller@1e0000 {
 			compatible = "marvell,cp110-icu";
-			reg = <0x1e0000 0x10>;
+			reg = <0x1e0000 0x440>;
 			#interrupt-cells = <3>;
 			interrupt-controller;
 			msi-parent = <&gicp>;

arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi

@@ -75,7 +75,7 @@
 
 		serial@75b1000 {
 			label = "LS-UART0";
-			status = "okay";
+			status = "disabled";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&blsp2_uart2_4pins_default>;
 			pinctrl-1 = <&blsp2_uart2_4pins_sleep>;

arch/arm64/boot/dts/qcom/msm8916.dtsi

@@ -1191,14 +1191,14 @@
 
 				port@0 {
 					reg = <0>;
-					etf_out: endpoint {
+					etf_in: endpoint {
 						slave-mode;
 						remote-endpoint = <&funnel0_out>;
 					};
 				};
 				port@1 {
 					reg = <0>;
-					etf_in: endpoint {
+					etf_out: endpoint {
 						remote-endpoint = <&replicator_in>;
 					};
 				};

arch/arm64/boot/dts/socionext/uniphier-ld11-global.dts

@@ -54,7 +54,7 @@
 	sound {
 		compatible = "audio-graph-card";
 		label = "UniPhier LD11";
-		widgets = "Headphone", "Headphone Jack";
+		widgets = "Headphone", "Headphones";
 		dais = <&i2s_port2
 			&i2s_port3
 			&i2s_port4

arch/arm64/boot/dts/socionext/uniphier-ld20-global.dts

@@ -54,7 +54,7 @@
 	sound {
 		compatible = "audio-graph-card";
 		label = "UniPhier LD20";
-		widgets = "Headphone", "Headphone Jack";
+		widgets = "Headphone", "Headphones";
 		dais = <&i2s_port2
 			&i2s_port3
 			&i2s_port4

arch/arm64/configs/defconfig

@@ -47,6 +47,7 @@ CONFIG_ARCH_MVEBU=y
 CONFIG_ARCH_QCOM=y
 CONFIG_ARCH_ROCKCHIP=y
 CONFIG_ARCH_SEATTLE=y
+CONFIG_ARCH_SYNQUACER=y
 CONFIG_ARCH_RENESAS=y
 CONFIG_ARCH_R8A7795=y
 CONFIG_ARCH_R8A7796=y
@@ -58,7 +59,6 @@ CONFIG_ARCH_R8A77995=y
 CONFIG_ARCH_STRATIX10=y
 CONFIG_ARCH_TEGRA=y
 CONFIG_ARCH_SPRD=y
-CONFIG_ARCH_SYNQUACER=y
 CONFIG_ARCH_THUNDER=y
 CONFIG_ARCH_THUNDER2=y
 CONFIG_ARCH_UNIPHIER=y
@@ -67,25 +67,23 @@ CONFIG_ARCH_XGENE=y
 CONFIG_ARCH_ZX=y
 CONFIG_ARCH_ZYNQMP=y
 CONFIG_PCI=y
-CONFIG_HOTPLUG_PCI_PCIE=y
 CONFIG_PCI_IOV=y
 CONFIG_HOTPLUG_PCI=y
 CONFIG_HOTPLUG_PCI_ACPI=y
-CONFIG_PCI_LAYERSCAPE=y
-CONFIG_PCI_HISI=y
-CONFIG_PCIE_QCOM=y
-CONFIG_PCIE_KIRIN=y
-CONFIG_PCIE_ARMADA_8K=y
-CONFIG_PCIE_HISI_STB=y
 CONFIG_PCI_AARDVARK=y
 CONFIG_PCI_TEGRA=y
 CONFIG_PCIE_RCAR=y
-CONFIG_PCIE_ROCKCHIP=y
-CONFIG_PCIE_ROCKCHIP_HOST=m
 CONFIG_PCI_HOST_GENERIC=y
 CONFIG_PCI_XGENE=y
 CONFIG_PCI_HOST_THUNDER_PEM=y
 CONFIG_PCI_HOST_THUNDER_ECAM=y
+CONFIG_PCIE_ROCKCHIP_HOST=m
+CONFIG_PCI_LAYERSCAPE=y
+CONFIG_PCI_HISI=y
+CONFIG_PCIE_QCOM=y
+CONFIG_PCIE_ARMADA_8K=y
+CONFIG_PCIE_KIRIN=y
+CONFIG_PCIE_HISI_STB=y
 CONFIG_ARM64_VA_BITS_48=y
 CONFIG_SCHED_MC=y
 CONFIG_NUMA=y
@@ -104,8 +102,6 @@ CONFIG_HIBERNATION=y
 CONFIG_WQ_POWER_EFFICIENT_DEFAULT=y
 CONFIG_ARM_CPUIDLE=y
 CONFIG_CPU_FREQ=y
-CONFIG_CPU_FREQ_GOV_ATTR_SET=y
-CONFIG_CPU_FREQ_GOV_COMMON=y
 CONFIG_CPU_FREQ_STAT=y
 CONFIG_CPU_FREQ_GOV_POWERSAVE=m
 CONFIG_CPU_FREQ_GOV_USERSPACE=y
@@ -113,11 +109,11 @@ CONFIG_CPU_FREQ_GOV_ONDEMAND=y
 CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
 CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
 CONFIG_CPUFREQ_DT=y
+CONFIG_ACPI_CPPC_CPUFREQ=m
 CONFIG_ARM_ARMADA_37XX_CPUFREQ=y
 CONFIG_ARM_BIG_LITTLE_CPUFREQ=y
 CONFIG_ARM_SCPI_CPUFREQ=y
 CONFIG_ARM_TEGRA186_CPUFREQ=y
-CONFIG_ACPI_CPPC_CPUFREQ=m
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -236,11 +232,6 @@ CONFIG_SMSC911X=y
 CONFIG_SNI_AVE=y
 CONFIG_SNI_NETSEC=y
 CONFIG_STMMAC_ETH=m
-CONFIG_DWMAC_IPQ806X=m
-CONFIG_DWMAC_MESON=m
-CONFIG_DWMAC_ROCKCHIP=m
-CONFIG_DWMAC_SUNXI=m
-CONFIG_DWMAC_SUN8I=m
 CONFIG_MDIO_BUS_MUX_MMIOREG=y
 CONFIG_AT803X_PHY=m
 CONFIG_MARVELL_PHY=m
@@ -269,8 +260,8 @@ CONFIG_WL18XX=m
 CONFIG_WLCORE_SDIO=m
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_ADC=m
-CONFIG_KEYBOARD_CROS_EC=y
 CONFIG_KEYBOARD_GPIO=y
+CONFIG_KEYBOARD_CROS_EC=y
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ATMEL_MXT=m
 CONFIG_INPUT_MISC=y
@@ -296,17 +287,13 @@ CONFIG_SERIAL_SAMSUNG=y
 CONFIG_SERIAL_SAMSUNG_CONSOLE=y
 CONFIG_SERIAL_TEGRA=y
 CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_NR_UARTS=11
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
 CONFIG_SERIAL_MSM=y
 CONFIG_SERIAL_MSM_CONSOLE=y
 CONFIG_SERIAL_XILINX_PS_UART=y
 CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
 CONFIG_SERIAL_MVEBU_UART=y
 CONFIG_SERIAL_DEV_BUS=y
-CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
 CONFIG_VIRTIO_CONSOLE=y
-CONFIG_I2C_HID=m
 CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_MUX=y
 CONFIG_I2C_MUX_PCA954x=y
@@ -325,26 +312,26 @@ CONFIG_I2C_RCAR=y
 CONFIG_I2C_CROS_EC_TUNNEL=y
 CONFIG_SPI=y
 CONFIG_SPI_ARMADA_3700=y
-CONFIG_SPI_MESON_SPICC=m
-CONFIG_SPI_MESON_SPIFC=m
 CONFIG_SPI_BCM2835=m
 CONFIG_SPI_BCM2835AUX=m
+CONFIG_SPI_MESON_SPICC=m
+CONFIG_SPI_MESON_SPIFC=m
 CONFIG_SPI_ORION=y
 CONFIG_SPI_PL022=y
-CONFIG_SPI_QUP=y
 CONFIG_SPI_ROCKCHIP=y
+CONFIG_SPI_QUP=y
 CONFIG_SPI_S3C64XX=y
 CONFIG_SPI_SPIDEV=m
 CONFIG_SPMI=y
-CONFIG_PINCTRL_IPQ8074=y
 CONFIG_PINCTRL_SINGLE=y
 CONFIG_PINCTRL_MAX77620=y
+CONFIG_PINCTRL_IPQ8074=y
 CONFIG_PINCTRL_MSM8916=y
 CONFIG_PINCTRL_MSM8994=y
 CONFIG_PINCTRL_MSM8996=y
-CONFIG_PINCTRL_MT7622=y
 CONFIG_PINCTRL_QDF2XXX=y
 CONFIG_PINCTRL_QCOM_SPMI_PMIC=y
+CONFIG_PINCTRL_MT7622=y
 CONFIG_GPIO_DWAPB=y
 CONFIG_GPIO_MB86S7X=y
 CONFIG_GPIO_PL061=y
@@ -368,13 +355,13 @@ CONFIG_SENSORS_INA2XX=m
 CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y
 CONFIG_CPU_THERMAL=y
 CONFIG_THERMAL_EMULATION=y
+CONFIG_ROCKCHIP_THERMAL=m
+CONFIG_RCAR_GEN3_THERMAL=y
 CONFIG_ARMADA_THERMAL=y
 CONFIG_BRCMSTB_THERMAL=m
 CONFIG_EXYNOS_THERMAL=y
-CONFIG_RCAR_GEN3_THERMAL=y
-CONFIG_QCOM_TSENS=y
-CONFIG_ROCKCHIP_THERMAL=m
 CONFIG_TEGRA_BPMP_THERMAL=m
+CONFIG_QCOM_TSENS=y
 CONFIG_UNIPHIER_THERMAL=y
 CONFIG_WATCHDOG=y
 CONFIG_S3C2410_WATCHDOG=y
@@ -395,9 +382,9 @@ CONFIG_MFD_MAX77620=y
 CONFIG_MFD_SPMI_PMIC=y
 CONFIG_MFD_RK808=y
 CONFIG_MFD_SEC_CORE=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_AXP20X=y
 CONFIG_REGULATOR_FAN53555=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_GPIO=y
 CONFIG_REGULATOR_HI6421V530=y
 CONFIG_REGULATOR_HI655X=y
@@ -407,16 +394,15 @@ CONFIG_REGULATOR_QCOM_SMD_RPM=y
 CONFIG_REGULATOR_QCOM_SPMI=y
 CONFIG_REGULATOR_RK808=y
 CONFIG_REGULATOR_S2MPS11=y
+CONFIG_RC_CORE=m
+CONFIG_RC_DECODERS=y
+CONFIG_RC_DEVICES=y
+CONFIG_IR_MESON=m
 CONFIG_MEDIA_SUPPORT=m
 CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
 CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
 CONFIG_MEDIA_CONTROLLER=y
-CONFIG_MEDIA_RC_SUPPORT=y
-CONFIG_RC_CORE=m
-CONFIG_RC_DEVICES=y
-CONFIG_RC_DECODERS=y
-CONFIG_IR_MESON=m
 CONFIG_VIDEO_V4L2_SUBDEV_API=y
 # CONFIG_DVB_NET is not set
 CONFIG_V4L_MEM2MEM_DRIVERS=y
@@ -441,8 +427,7 @@ CONFIG_ROCKCHIP_DW_HDMI=y
 CONFIG_ROCKCHIP_DW_MIPI_DSI=y
 CONFIG_ROCKCHIP_INNO_HDMI=y
 CONFIG_DRM_RCAR_DU=m
-CONFIG_DRM_RCAR_LVDS=y
-CONFIG_DRM_RCAR_VSP=y
+CONFIG_DRM_RCAR_LVDS=m
 CONFIG_DRM_TEGRA=m
 CONFIG_DRM_PANEL_SIMPLE=m
 CONFIG_DRM_I2C_ADV7511=m
@@ -455,7 +440,6 @@ CONFIG_FB_ARMCLCD=y
 CONFIG_BACKLIGHT_GENERIC=m
 CONFIG_BACKLIGHT_PWM=m
 CONFIG_BACKLIGHT_LP855X=m
-CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_LOGO=y
 # CONFIG_LOGO_LINUX_MONO is not set
 # CONFIG_LOGO_LINUX_VGA16 is not set
@@ -468,6 +452,7 @@ CONFIG_SND_SOC_RCAR=m
 CONFIG_SND_SOC_AK4613=m
 CONFIG_SND_SIMPLE_CARD=m
 CONFIG_SND_AUDIO_GRAPH_CARD=m
+CONFIG_I2C_HID=m
 CONFIG_USB=y
 CONFIG_USB_OTG=y
 CONFIG_USB_XHCI_HCD=y
@@ -501,12 +486,12 @@ CONFIG_MMC_BLOCK_MINORS=32
 CONFIG_MMC_ARMMMCI=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ACPI=y
-CONFIG_MMC_SDHCI_F_SDH30=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI_OF_ARASAN=y
 CONFIG_MMC_SDHCI_OF_ESDHC=y
 CONFIG_MMC_SDHCI_CADENCE=y
 CONFIG_MMC_SDHCI_TEGRA=y
+CONFIG_MMC_SDHCI_F_SDH30=y
 CONFIG_MMC_MESON_GX=y
 CONFIG_MMC_SDHCI_MSM=y
 CONFIG_MMC_SPI=y
@@ -524,11 +509,11 @@ CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_PWM=y
 CONFIG_LEDS_SYSCON=y
+CONFIG_LEDS_TRIGGER_DISK=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
 CONFIG_LEDS_TRIGGER_PANIC=y
-CONFIG_LEDS_TRIGGER_DISK=y
 CONFIG_EDAC=y
 CONFIG_EDAC_GHES=y
 CONFIG_RTC_CLASS=y
@@ -537,13 +522,13 @@ CONFIG_RTC_DRV_RK808=m
 CONFIG_RTC_DRV_S5M=y
 CONFIG_RTC_DRV_DS3232=y
 CONFIG_RTC_DRV_EFI=y
+CONFIG_RTC_DRV_CROS_EC=y
 CONFIG_RTC_DRV_S3C=y
 CONFIG_RTC_DRV_PL031=y
 CONFIG_RTC_DRV_SUN6I=y
 CONFIG_RTC_DRV_ARMADA38X=y
 CONFIG_RTC_DRV_TEGRA=y
 CONFIG_RTC_DRV_XGENE=y
-CONFIG_RTC_DRV_CROS_EC=y
 CONFIG_DMADEVICES=y
 CONFIG_DMA_BCM2835=m
 CONFIG_K3_DMA=y
@@ -579,7 +564,6 @@ CONFIG_HWSPINLOCK_QCOM=y
 CONFIG_ARM_MHU=y
 CONFIG_PLATFORM_MHU=y
 CONFIG_BCM2835_MBOX=y
-CONFIG_HI6220_MBOX=y
 CONFIG_QCOM_APCS_IPC=y
 CONFIG_ROCKCHIP_IOMMU=y
 CONFIG_TEGRA_IOMMU_SMMU=y
@@ -602,7 +586,6 @@ CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND=y
 CONFIG_EXTCON_USB_GPIO=y
 CONFIG_EXTCON_USBC_CROS_EC=y
 CONFIG_MEMORY=y
-CONFIG_TEGRA_MC=y
 CONFIG_IIO=y
 CONFIG_EXYNOS_ADC=y
 CONFIG_ROCKCHIP_SARADC=m
@@ -618,27 +601,27 @@ CONFIG_PWM_RCAR=m
 CONFIG_PWM_ROCKCHIP=y
 CONFIG_PWM_SAMSUNG=y
 CONFIG_PWM_TEGRA=m
+CONFIG_PHY_XGENE=y
+CONFIG_PHY_SUN4I_USB=y
+CONFIG_PHY_HI6220_USB=y
 CONFIG_PHY_HISTB_COMBPHY=y
 CONFIG_PHY_HISI_INNO_USB2=y
-CONFIG_PHY_RCAR_GEN3_USB2=y
-CONFIG_PHY_RCAR_GEN3_USB3=m
-CONFIG_PHY_HI6220_USB=y
-CONFIG_PHY_QCOM_USB_HS=y
-CONFIG_PHY_SUN4I_USB=y
 CONFIG_PHY_MVEBU_CP110_COMPHY=y
 CONFIG_PHY_QCOM_QMP=m
-CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_QCOM_USB_HS=y
+CONFIG_PHY_RCAR_GEN3_USB2=y
+CONFIG_PHY_RCAR_GEN3_USB3=m
 CONFIG_PHY_ROCKCHIP_EMMC=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
 CONFIG_PHY_ROCKCHIP_PCIE=m
 CONFIG_PHY_ROCKCHIP_TYPEC=y
-CONFIG_PHY_XGENE=y
 CONFIG_PHY_TEGRA_XUSB=y
 CONFIG_QCOM_L2_PMU=y
 CONFIG_QCOM_L3_PMU=y
-CONFIG_MESON_EFUSE=m
 CONFIG_QCOM_QFPROM=y
 CONFIG_ROCKCHIP_EFUSE=y
 CONFIG_UNIPHIER_EFUSE=y
+CONFIG_MESON_EFUSE=m
 CONFIG_TEE=y
 CONFIG_OPTEE=y
 CONFIG_ARM_SCPI_PROTOCOL=y
@@ -647,7 +630,6 @@ CONFIG_EFI_CAPSULE_LOADER=y
 CONFIG_ACPI=y
 CONFIG_ACPI_APEI=y
 CONFIG_ACPI_APEI_GHES=y
-CONFIG_ACPI_APEI_PCIEAER=y
 CONFIG_ACPI_APEI_MEMORY_FAILURE=y
 CONFIG_ACPI_APEI_EINJ=y
 CONFIG_EXT2_FS=y
@@ -682,7 +664,6 @@ CONFIG_DEBUG_INFO=y
 CONFIG_DEBUG_FS=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
-CONFIG_LOCKUP_DETECTOR=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_DEBUG_PREEMPT is not set
 # CONFIG_FTRACE is not set
@@ -691,20 +672,15 @@ CONFIG_SECURITY=y
 CONFIG_CRYPTO_ECHAINIV=y
 CONFIG_CRYPTO_ANSI_CPRNG=y
 CONFIG_ARM64_CRYPTO=y
-CONFIG_CRYPTO_SHA256_ARM64=m
-CONFIG_CRYPTO_SHA512_ARM64=m
 CONFIG_CRYPTO_SHA1_ARM64_CE=y
 CONFIG_CRYPTO_SHA2_ARM64_CE=y
+CONFIG_CRYPTO_SHA512_ARM64_CE=m
+CONFIG_CRYPTO_SHA3_ARM64=m
+CONFIG_CRYPTO_SM3_ARM64_CE=m
 CONFIG_CRYPTO_GHASH_ARM64_CE=y
 CONFIG_CRYPTO_CRCT10DIF_ARM64_CE=m
 CONFIG_CRYPTO_CRC32_ARM64_CE=m
-CONFIG_CRYPTO_AES_ARM64=m
-CONFIG_CRYPTO_AES_ARM64_CE=m
 CONFIG_CRYPTO_AES_ARM64_CE_CCM=y
 CONFIG_CRYPTO_AES_ARM64_CE_BLK=y
-CONFIG_CRYPTO_AES_ARM64_NEON_BLK=m
 CONFIG_CRYPTO_CHACHA20_NEON=m
 CONFIG_CRYPTO_AES_ARM64_BS=m
-CONFIG_CRYPTO_SHA512_ARM64_CE=m
-CONFIG_CRYPTO_SHA3_ARM64=m
-CONFIG_CRYPTO_SM3_ARM64_CE=m

arch/arm64/include/asm/alternative.h

@@ -28,7 +28,12 @@ typedef void (*alternative_cb_t)(struct alt_instr *alt,
 				 __le32 *origptr, __le32 *updptr, int nr_inst);
 
 void __init apply_alternatives_all(void);
-void apply_alternatives(void *start, size_t length);
+
+#ifdef CONFIG_MODULES
+void apply_alternatives_module(void *start, size_t length);
+#else
+static inline void apply_alternatives_module(void *start, size_t length) { }
+#endif
 
 #define ALTINSTR_ENTRY(feature,cb)					      \
 	" .word 661b - .\n"				/* label           */ \

arch/arm64/include/asm/pgtable.h

@@ -224,10 +224,8 @@ static inline void set_pte(pte_t *ptep, pte_t pte)
 	 * Only if the new pte is valid and kernel, otherwise TLB maintenance
 	 * or update_mmu_cache() have the necessary barriers.
 	 */
-	if (pte_valid_not_user(pte)) {
+	if (pte_valid_not_user(pte))
 		dsb(ishst);
-		isb();
-	}
 }
 
 extern void __sync_icache_dcache(pte_t pteval);
@@ -434,7 +432,6 @@ static inline void set_pmd(pmd_t *pmdp, pmd_t pmd)
 {
 	WRITE_ONCE(*pmdp, pmd);
 	dsb(ishst);
-	isb();
 }
 
 static inline void pmd_clear(pmd_t *pmdp)
@@ -485,7 +482,6 @@ static inline void set_pud(pud_t *pudp, pud_t pud)
 {
 	WRITE_ONCE(*pudp, pud);
 	dsb(ishst);
-	isb();
 }
 
 static inline void pud_clear(pud_t *pudp)

arch/arm64/kernel/alternative.c

@@ -122,7 +122,30 @@ static void patch_alternative(struct alt_instr *alt,
 	}
 }
 
-static void __apply_alternatives(void *alt_region, bool use_linear_alias)
+/*
+ * We provide our own, private D-cache cleaning function so that we don't
+ * accidentally call into the cache.S code, which is patched by us at
+ * runtime.
+ */
+static void clean_dcache_range_nopatch(u64 start, u64 end)
+{
+	u64 cur, d_size, ctr_el0;
+
+	ctr_el0 = read_sanitised_ftr_reg(SYS_CTR_EL0);
+	d_size = 4 << cpuid_feature_extract_unsigned_field(ctr_el0,
+							   CTR_DMINLINE_SHIFT);
+	cur = start & ~(d_size - 1);
+	do {
+		/*
+		 * We must clean+invalidate to the PoC in order to avoid
+		 * Cortex-A53 errata 826319, 827319, 824069 and 819472
+		 * (this corresponds to ARM64_WORKAROUND_CLEAN_CACHE)
+		 */
+		asm volatile("dc civac, %0" : : "r" (cur) : "memory");
+	} while (cur += d_size, cur < end);
+}
+
+static void __apply_alternatives(void *alt_region, bool is_module)
 {
 	struct alt_instr *alt;
 	struct alt_region *region = alt_region;
@@ -145,7 +168,7 @@ static void __apply_alternatives(void *alt_region, bool use_linear_alias)
 		pr_info_once("patching kernel code\n");
 
 		origptr = ALT_ORIG_PTR(alt);
-		updptr = use_linear_alias ? lm_alias(origptr) : origptr;
+		updptr = is_module ? origptr : lm_alias(origptr);
 		nr_inst = alt->orig_len / AARCH64_INSN_SIZE;
 
 		if (alt->cpufeature < ARM64_CB_PATCH)
@@ -155,8 +178,20 @@ static void __apply_alternatives(void *alt_region, bool use_linear_alias)
 
 		alt_cb(alt, origptr, updptr, nr_inst);
 
-		flush_icache_range((uintptr_t)origptr,
-				   (uintptr_t)(origptr + nr_inst));
+		if (!is_module) {
+			clean_dcache_range_nopatch((u64)origptr,
+						   (u64)(origptr + nr_inst));
+		}
+	}
+
+	/*
+	 * The core module code takes care of cache maintenance in
+	 * flush_module_icache().
+	 */
+	if (!is_module) {
+		dsb(ish);
+		__flush_icache_all();
+		isb();
 	}
 }
 
@@ -178,7 +213,7 @@ static int __apply_alternatives_multi_stop(void *unused)
 		isb();
 	} else {
 		BUG_ON(alternatives_applied);
-		__apply_alternatives(&region, true);
+		__apply_alternatives(&region, false);
 		/* Barriers provided by the cache flushing */
 		WRITE_ONCE(alternatives_applied, 1);
 	}
@@ -192,12 +227,14 @@ void __init apply_alternatives_all(void)
 	stop_machine(__apply_alternatives_multi_stop, NULL, cpu_online_mask);
 }
 
-void apply_alternatives(void *start, size_t length)
+#ifdef CONFIG_MODULES
+void apply_alternatives_module(void *start, size_t length)
 {
 	struct alt_region region = {
 		.begin	= start,
 		.end	= start + length,
 	};
 
-	__apply_alternatives(&region, false);
+	__apply_alternatives(&region, true);
 }
+#endif

arch/arm64/kernel/module.c

@@ -448,9 +448,8 @@ int module_finalize(const Elf_Ehdr *hdr,
 	const char *secstrs = (void *)hdr + sechdrs[hdr->e_shstrndx].sh_offset;
 
 	for (s = sechdrs, se = sechdrs + hdr->e_shnum; s < se; s++) {
-		if (strcmp(".altinstructions", secstrs + s->sh_name) == 0) {
-			apply_alternatives((void *)s->sh_addr, s->sh_size);
-		}
+		if (strcmp(".altinstructions", secstrs + s->sh_name) == 0)
+			apply_alternatives_module((void *)s->sh_addr, s->sh_size);
 #ifdef CONFIG_ARM64_MODULE_PLTS
 		if (IS_ENABLED(CONFIG_DYNAMIC_FTRACE) &&
 		    !strcmp(".text.ftrace_trampoline", secstrs + s->sh_name))

arch/microblaze/Kconfig.debug

@@ -8,11 +8,4 @@ config TRACE_IRQFLAGS_SUPPORT
 
 source "lib/Kconfig.debug"
 
-config HEART_BEAT
-	bool "Heart beat function for kernel"
-	default n
-	help
-	  This option turns on/off heart beat kernel functionality.
-	  First GPIO node is taken.
-
 endmenu

arch/microblaze/include/asm/setup.h

@@ -19,15 +19,10 @@ extern char cmd_line[COMMAND_LINE_SIZE];
 
 extern char *klimit;
 
-void microblaze_heartbeat(void);
-void microblaze_setup_heartbeat(void);
-
 #   ifdef CONFIG_MMU
 extern void mmu_reset(void);
 #   endif /* CONFIG_MMU */
 
-extern void of_platform_reset_gpio_probe(void);
-
 void time_init(void);
 void init_IRQ(void);
 void machine_early_init(const char *cmdline, unsigned int ram,

arch/microblaze/include/asm/unistd.h

@@ -38,6 +38,6 @@
 
 #endif /* __ASSEMBLY__ */
 
-#define __NR_syscalls         399
+#define __NR_syscalls         401
 
 #endif /* _ASM_MICROBLAZE_UNISTD_H */

arch/microblaze/include/uapi/asm/unistd.h

@@ -415,5 +415,7 @@
 #define __NR_pkey_alloc		396
 #define __NR_pkey_free		397
 #define __NR_statx		398
+#define __NR_io_pgetevents	399
+#define __NR_rseq		400
 
 #endif /* _UAPI_ASM_MICROBLAZE_UNISTD_H */

arch/microblaze/kernel/Makefile

@@ -8,7 +8,6 @@ ifdef CONFIG_FUNCTION_TRACER
 CFLAGS_REMOVE_timer.o = -pg
 CFLAGS_REMOVE_intc.o = -pg
 CFLAGS_REMOVE_early_printk.o = -pg
-CFLAGS_REMOVE_heartbeat.o = -pg
 CFLAGS_REMOVE_ftrace.o = -pg
 CFLAGS_REMOVE_process.o = -pg
 endif
@@ -17,12 +16,11 @@ extra-y := head.o vmlinux.lds
 
 obj-y += dma.o exceptions.o \
 	hw_exception_handler.o irq.o \
-	platform.o process.o prom.o ptrace.o \
+	process.o prom.o ptrace.o \
 	reset.o setup.o signal.o sys_microblaze.o timer.o traps.o unwind.o
 
 obj-y += cpu/
 
-obj-$(CONFIG_HEART_BEAT)	+= heartbeat.o
 obj-$(CONFIG_MODULES)		+= microblaze_ksyms.o module.o
 obj-$(CONFIG_MMU)		+= misc.o
 obj-$(CONFIG_STACKTRACE)	+= stacktrace.o

arch/microblaze/kernel/heartbeat.c

-/*
- * Copyright (C) 2007-2009 Michal Simek <monstr@monstr.eu>
- * Copyright (C) 2007-2009 PetaLogix
- * Copyright (C) 2006 Atmark Techno, Inc.
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/sched.h>
-#include <linux/sched/loadavg.h>
-#include <linux/io.h>
-
-#include <asm/setup.h>
-#include <asm/page.h>
-#include <asm/prom.h>
-
-static unsigned int base_addr;
-
-void microblaze_heartbeat(void)
-{
-	static unsigned int cnt, period, dist;
-
-	if (base_addr) {
-		if (cnt == 0 || cnt == dist)
-			out_be32(base_addr, 1);
-		else if (cnt == 7 || cnt == dist + 7)
-			out_be32(base_addr, 0);
-
-		if (++cnt > period) {
-			cnt = 0;
-			/*
-			 * The hyperbolic function below modifies the heartbeat
-			 * period length in dependency of the current (5min)
-			 * load. It goes through the points f(0)=126, f(1)=86,
-			 * f(5)=51, f(inf)->30.
-			 */
-			period = ((672 << FSHIFT) / (5 * avenrun[0] +
-						(7 << FSHIFT))) + 30;
-			dist = period / 4;
-		}
-	}
-}
-
-void microblaze_setup_heartbeat(void)
-{
-	struct device_node *gpio = NULL;
-	int *prop;
-	int j;
-	const char * const gpio_list[] = {
-		"xlnx,xps-gpio-1.00.a",
-		NULL
-	};
-
-	for (j = 0; gpio_list[j] != NULL; j++) {
-		gpio = of_find_compatible_node(NULL, NULL, gpio_list[j]);
-		if (gpio)
-			break;
-	}
-
-	if (gpio) {
-		base_addr = be32_to_cpup(of_get_property(gpio, "reg", NULL));
-		base_addr = (unsigned long) ioremap(base_addr, PAGE_SIZE);
-		pr_notice("Heartbeat GPIO at 0x%x\n", base_addr);
-
-		/* GPIO is configured as output */
-		prop = (int *) of_get_property(gpio, "xlnx,is-bidir", NULL);
-		if (prop)
-			out_be32(base_addr + 4, 0);
-	}
-}

arch/microblaze/kernel/platform.c

-/*
- * Copyright 2008 Michal Simek <monstr@monstr.eu>
- *
- * based on virtex.c file
- *
- * Copyright 2007 Secret Lab Technologies Ltd.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include <linux/init.h>
-#include <linux/of_platform.h>
-#include <asm/setup.h>
-
-static struct of_device_id xilinx_of_bus_ids[] __initdata = {
-	{ .compatible = "simple-bus", },
-	{ .compatible = "xlnx,compound", },
-	{}
-};
-
-static int __init microblaze_device_probe(void)
-{
-	of_platform_bus_probe(NULL, xilinx_of_bus_ids, NULL);
-	of_platform_reset_gpio_probe();
-	return 0;
-}
-device_initcall(microblaze_device_probe);

arch/microblaze/kernel/reset.c

@@ -18,7 +18,7 @@
 static int handle; /* reset pin handle */
 static unsigned int reset_val;
 
-void of_platform_reset_gpio_probe(void)
+static int of_platform_reset_gpio_probe(void)
 {
 	int ret;
 	handle = of_get_named_gpio(of_find_node_by_path("/"),
@@ -27,13 +27,13 @@ void of_platform_reset_gpio_probe(void)
 	if (!gpio_is_valid(handle)) {
 		pr_info("Skipping unavailable RESET gpio %d (%s)\n",
 				handle, "reset");
-		return;
+		return -ENODEV;
 	}
 
 	ret = gpio_request(handle, "reset");
 	if (ret < 0) {
 		pr_info("GPIO pin is already allocated\n");
-		return;
+		return ret;
 	}
 
 	/* get current setup value */
@@ -51,11 +51,12 @@ void of_platform_reset_gpio_probe(void)
 
 	pr_info("RESET: Registered gpio device: %d, current val: %d\n",
 							handle, reset_val);
-	return;
+	return 0;
 err:
 	gpio_free(handle);
-	return;
+	return ret;
 }
+device_initcall(of_platform_reset_gpio_probe);
 
 
 static void gpio_system_reset(void)

arch/microblaze/kernel/syscall_table.S

@@ -400,3 +400,5 @@ ENTRY(sys_call_table)
 	.long sys_pkey_alloc
 	.long sys_pkey_free
 	.long sys_statx
+	.long sys_io_pgetevents
+	.long sys_rseq

arch/microblaze/kernel/timer.c

@@ -156,9 +156,6 @@ static inline void timer_ack(void)
 static irqreturn_t timer_interrupt(int irq, void *dev_id)
 {
 	struct clock_event_device *evt = &clockevent_xilinx_timer;
-#ifdef CONFIG_HEART_BEAT
-	microblaze_heartbeat();
-#endif
 	timer_ack();
 	evt->event_handler(evt);
 	return IRQ_HANDLED;
@@ -318,10 +315,6 @@ static int __init xilinx_timer_init(struct device_node *timer)
 		return ret;
 	}
 
-#ifdef CONFIG_HEART_BEAT
-	microblaze_setup_heartbeat();
-#endif
-
 	ret = xilinx_clocksource_init();
 	if (ret)
 		return ret;

arch/mips/kernel/signal.c

@@ -801,7 +801,7 @@ static void handle_signal(struct ksignal *ksig, struct pt_regs *regs)
 		regs->regs[0] = 0;		/* Don't deal with this again.	*/
 	}
 
-	rseq_signal_deliver(regs);
+	rseq_signal_deliver(ksig, regs);
 
 	if (sig_uses_siginfo(&ksig->ka, abi))
 		ret = abi->setup_rt_frame(vdso + abi->vdso->off_rt_sigreturn,
@@ -870,7 +870,7 @@ asmlinkage void do_notify_resume(struct pt_regs *regs, void *unused,
 	if (thread_info_flags & _TIF_NOTIFY_RESUME) {
 		clear_thread_flag(TIF_NOTIFY_RESUME);
 		tracehook_notify_resume(regs);
-		rseq_handle_notify_resume(regs);
+		rseq_handle_notify_resume(NULL, regs);
 	}
 
 	user_enter();

arch/parisc/Kconfig

@@ -244,11 +244,11 @@ config PARISC_PAGE_SIZE_4KB
 
 config PARISC_PAGE_SIZE_16KB
 	bool "16KB"
-	depends on PA8X00
+	depends on PA8X00 && BROKEN
 
 config PARISC_PAGE_SIZE_64KB
 	bool "64KB"
-	depends on PA8X00
+	depends on PA8X00 && BROKEN
 
 endchoice
 
@@ -347,7 +347,7 @@ config NR_CPUS
 	int "Maximum number of CPUs (2-32)"
 	range 2 32
 	depends on SMP
-	default "32"
+	default "4"
 
 endmenu
 

arch/parisc/Makefile

@@ -65,10 +65,6 @@ endif
 # kernel.
 cflags-y	+= -mdisable-fpregs
 
-# Without this, "ld -r" results in .text sections that are too big
-# (> 0x40000) for branches to reach stubs.
-cflags-y	+= -ffunction-sections
-
 # Use long jumps instead of long branches (needed if your linker fails to
 # link a too big vmlinux executable). Not enabled for building modules.
 ifdef CONFIG_MLONGCALLS

arch/parisc/include/asm/signal.h

@@ -21,14 +21,6 @@ typedef struct {
 	unsigned long sig[_NSIG_WORDS];
 } sigset_t;
 
-#ifndef __KERNEL__
-struct sigaction {
-	__sighandler_t sa_handler;
-	unsigned long sa_flags;
-	sigset_t sa_mask;		/* mask last for extensibility */
-};
-#endif
-
 #include <asm/sigcontext.h>
 
 #endif /* !__ASSEMBLY */

arch/parisc/include/uapi/asm/unistd.h

@@ -364,8 +364,9 @@
 #define __NR_preadv2		(__NR_Linux + 347)
 #define __NR_pwritev2		(__NR_Linux + 348)
 #define __NR_statx		(__NR_Linux + 349)
+#define __NR_io_pgetevents	(__NR_Linux + 350)
 
-#define __NR_Linux_syscalls	(__NR_statx + 1)
+#define __NR_Linux_syscalls	(__NR_io_pgetevents + 1)
 
 
 #define __IGNORE_select		/* newselect */

arch/parisc/kernel/drivers.c

@@ -154,17 +154,14 @@ int register_parisc_driver(struct parisc_driver *driver)
 {
 	/* FIXME: we need this because apparently the sti
 	 * driver can be registered twice */
-	if(driver->drv.name) {
-		printk(KERN_WARNING 
-		       "BUG: skipping previously registered driver %s\n",
-		       driver->name);
+	if (driver->drv.name) {
+		pr_warn("BUG: skipping previously registered driver %s\n",
+			driver->name);
 		return 1;
 	}
 
 	if (!driver->probe) {
-		printk(KERN_WARNING 
-		       "BUG: driver %s has no probe routine\n",
-		       driver->name);
+		pr_warn("BUG: driver %s has no probe routine\n", driver->name);
 		return 1;
 	}
 
@@ -491,12 +488,9 @@ alloc_pa_dev(unsigned long hpa, struct hardware_path *mod_path)
 
 	dev = create_parisc_device(mod_path);
 	if (dev->id.hw_type != HPHW_FAULTY) {
-		printk(KERN_ERR "Two devices have hardware path [%s].  "
-				"IODC data for second device: "
-				"%02x%02x%02x%02x%02x%02x\n"
-				"Rearranging GSC cards sometimes helps\n",
-			parisc_pathname(dev), iodc_data[0], iodc_data[1],
-			iodc_data[3], iodc_data[4], iodc_data[5], iodc_data[6]);
+		pr_err("Two devices have hardware path [%s].  IODC data for second device: %7phN\n"
+		       "Rearranging GSC cards sometimes helps\n",
+			parisc_pathname(dev), iodc_data);
 		return NULL;
 	}
 
@@ -528,8 +522,7 @@ alloc_pa_dev(unsigned long hpa, struct hardware_path *mod_path)
 	 * the keyboard controller
 	 */
 	if ((hpa & 0xfff) == 0 && insert_resource(&iomem_resource, &dev->hpa))
-		printk("Unable to claim HPA %lx for device %s\n",
-				hpa, name);
+		pr_warn("Unable to claim HPA %lx for device %s\n", hpa, name);
 
 	return dev;
 }
@@ -875,7 +868,7 @@ static void print_parisc_device(struct parisc_device *dev)
 	static int count;
 
 	print_pa_hwpath(dev, hw_path);
-	printk(KERN_INFO "%d. %s at 0x%px [%s] { %d, 0x%x, 0x%.3x, 0x%.5x }",
+	pr_info("%d. %s at 0x%px [%s] { %d, 0x%x, 0x%.3x, 0x%.5x }",
 		++count, dev->name, (void*) dev->hpa.start, hw_path, dev->id.hw_type,
 		dev->id.hversion_rev, dev->id.hversion, dev->id.sversion);
 

arch/parisc/kernel/syscall_table.S

@@ -445,6 +445,7 @@
 	ENTRY_COMP(preadv2)
 	ENTRY_COMP(pwritev2)
 	ENTRY_SAME(statx)
+	ENTRY_COMP(io_pgetevents)	/* 350 */
 
 
 .ifne (. - 90b) - (__NR_Linux_syscalls * (91b - 90b))

arch/parisc/kernel/unwind.c

@@ -25,7 +25,7 @@
 
 /* #define DEBUG 1 */
 #ifdef DEBUG
-#define dbg(x...) printk(x)
+#define dbg(x...) pr_debug(x)
 #else
 #define dbg(x...)
 #endif
@@ -182,7 +182,7 @@ int __init unwind_init(void)
 	start = (long)&__start___unwind[0];
 	stop = (long)&__stop___unwind[0];
 
-	printk("unwind_init: start = 0x%lx, end = 0x%lx, entries = %lu\n", 
+	dbg("unwind_init: start = 0x%lx, end = 0x%lx, entries = %lu\n",
 	    start, stop,
 	    (stop - start) / sizeof(struct unwind_table_entry));
 

arch/powerpc/include/asm/book3s/32/pgalloc.h

@@ -138,7 +138,6 @@ static inline void pgtable_free_tlb(struct mmu_gather *tlb,
 static inline void __pte_free_tlb(struct mmu_gather *tlb, pgtable_t table,
 				  unsigned long address)
 {
-	pgtable_page_dtor(table);
 	pgtable_free_tlb(tlb, page_address(table), 0);
 }
 #endif /* _ASM_POWERPC_BOOK3S_32_PGALLOC_H */

arch/powerpc/include/asm/nohash/32/pgalloc.h

@@ -140,7 +140,6 @@ static inline void __pte_free_tlb(struct mmu_gather *tlb, pgtable_t table,
 				  unsigned long address)
 {
 	tlb_flush_pgtable(tlb, address);
-	pgtable_page_dtor(table);
 	pgtable_free_tlb(tlb, page_address(table), 0);
 }
 #endif /* _ASM_POWERPC_PGALLOC_32_H */

arch/powerpc/include/asm/systbl.h

@@ -393,3 +393,4 @@ SYSCALL(pkey_alloc)
 SYSCALL(pkey_free)
 SYSCALL(pkey_mprotect)
 SYSCALL(rseq)
+COMPAT_SYS(io_pgetevents)

arch/powerpc/include/asm/unistd.h

@@ -12,7 +12,7 @@
 #include <uapi/asm/unistd.h>
 
 
-#define NR_syscalls		388
+#define NR_syscalls		389
 
 #define __NR__exit __NR_exit
 

arch/powerpc/include/uapi/asm/unistd.h

@@ -399,5 +399,6 @@
 #define __NR_pkey_free		385
 #define __NR_pkey_mprotect	386
 #define __NR_rseq		387
+#define __NR_io_pgetevents	388
 
 #endif /* _UAPI_ASM_POWERPC_UNISTD_H_ */

arch/powerpc/kernel/pci_32.c

@@ -285,9 +285,6 @@ pci_bus_to_hose(int bus)
  * Note that the returned IO or memory base is a physical address
  */
 
-#pragma GCC diagnostic push
-#pragma GCC diagnostic ignored "-Wpragmas"
-#pragma GCC diagnostic ignored "-Wattribute-alias"
 SYSCALL_DEFINE3(pciconfig_iobase, long, which,
 		unsigned long, bus, unsigned long, devfn)
 {
@@ -313,4 +310,3 @@ SYSCALL_DEFINE3(pciconfig_iobase, long, which,
 
 	return result;
 }
-#pragma GCC diagnostic pop

arch/powerpc/kernel/pci_64.c

@@ -203,9 +203,6 @@ void pcibios_setup_phb_io_space(struct pci_controller *hose)
 #define IOBASE_ISA_IO		3
 #define IOBASE_ISA_MEM		4
 
-#pragma GCC diagnostic push
-#pragma GCC diagnostic ignored "-Wpragmas"
-#pragma GCC diagnostic ignored "-Wattribute-alias"
 SYSCALL_DEFINE3(pciconfig_iobase, long, which, unsigned long, in_bus,
 			  unsigned long, in_devfn)
 {
@@ -259,7 +256,6 @@ SYSCALL_DEFINE3(pciconfig_iobase, long, which, unsigned long, in_bus,
 
 	return -EOPNOTSUPP;
 }
-#pragma GCC diagnostic pop
 
 #ifdef CONFIG_NUMA
 int pcibus_to_node(struct pci_bus *bus)

arch/powerpc/kernel/rtas.c

@@ -1051,9 +1051,6 @@ struct pseries_errorlog *get_pseries_errorlog(struct rtas_error_log *log,
 }
 
 /* We assume to be passed big endian arguments */
-#pragma GCC diagnostic push
-#pragma GCC diagnostic ignored "-Wpragmas"
-#pragma GCC diagnostic ignored "-Wattribute-alias"
 SYSCALL_DEFINE1(rtas, struct rtas_args __user *, uargs)
 {
 	struct rtas_args args;
@@ -1140,7 +1137,6 @@ SYSCALL_DEFINE1(rtas, struct rtas_args __user *, uargs)
 
 	return 0;
 }
-#pragma GCC diagnostic pop
 
 /*
  * Call early during boot, before mem init, to retrieve the RTAS

arch/powerpc/kernel/signal_32.c

@@ -1038,9 +1038,6 @@ static int do_setcontext_tm(struct ucontext __user *ucp,
 }
 #endif
 
-#pragma GCC diagnostic push
-#pragma GCC diagnostic ignored "-Wpragmas"
-#pragma GCC diagnostic ignored "-Wattribute-alias"
 #ifdef CONFIG_PPC64
 COMPAT_SYSCALL_DEFINE3(swapcontext, struct ucontext __user *, old_ctx,
 		       struct ucontext __user *, new_ctx, int, ctx_size)
@@ -1134,7 +1131,6 @@ SYSCALL_DEFINE3(swapcontext, struct ucontext __user *, old_ctx,
 	set_thread_flag(TIF_RESTOREALL);
 	return 0;
 }
-#pragma GCC diagnostic pop
 
 #ifdef CONFIG_PPC64
 COMPAT_SYSCALL_DEFINE0(rt_sigreturn)
@@ -1231,9 +1227,6 @@ SYSCALL_DEFINE0(rt_sigreturn)
 	return 0;
 }
 
-#pragma GCC diagnostic push
-#pragma GCC diagnostic ignored "-Wpragmas"
-#pragma GCC diagnostic ignored "-Wattribute-alias"
 #ifdef CONFIG_PPC32
 SYSCALL_DEFINE3(debug_setcontext, struct ucontext __user *, ctx,
 			 int, ndbg, struct sig_dbg_op __user *, dbg)
@@ -1337,7 +1330,6 @@ SYSCALL_DEFINE3(debug_setcontext, struct ucontext __user *, ctx,
 	return 0;
 }
 #endif
-#pragma GCC diagnostic pop
 
 /*
  * OK, we're invoking a handler

arch/powerpc/kernel/signal_64.c

@@ -625,9 +625,6 @@ static long setup_trampoline(unsigned int syscall, unsigned int __user *tramp)
 /*
  * Handle {get,set,swap}_context operations
  */
-#pragma GCC diagnostic push
-#pragma GCC diagnostic ignored "-Wpragmas"
-#pragma GCC diagnostic ignored "-Wattribute-alias"
 SYSCALL_DEFINE3(swapcontext, struct ucontext __user *, old_ctx,
 		struct ucontext __user *, new_ctx, long, ctx_size)
 {
@@ -693,7 +690,6 @@ SYSCALL_DEFINE3(swapcontext, struct ucontext __user *, old_ctx,
 	set_thread_flag(TIF_RESTOREALL);
 	return 0;
 }
-#pragma GCC diagnostic pop
 
 
 /*

arch/powerpc/kernel/syscalls.c

@@ -62,9 +62,6 @@ static inline long do_mmap2(unsigned long addr, size_t len,
 	return ret;
 }
 
-#pragma GCC diagnostic push
-#pragma GCC diagnostic ignored "-Wpragmas"
-#pragma GCC diagnostic ignored "-Wattribute-alias"
 SYSCALL_DEFINE6(mmap2, unsigned long, addr, size_t, len,
 		unsigned long, prot, unsigned long, flags,
 		unsigned long, fd, unsigned long, pgoff)
@@ -78,7 +75,6 @@ SYSCALL_DEFINE6(mmap, unsigned long, addr, size_t, len,
 {
 	return do_mmap2(addr, len, prot, flags, fd, offset, PAGE_SHIFT);
 }
-#pragma GCC diagnostic pop
 
 #ifdef CONFIG_PPC32
 /*

arch/powerpc/mm/subpage-prot.c

@@ -186,9 +186,6 @@ static void subpage_mark_vma_nohuge(struct mm_struct *mm, unsigned long addr,
  * in a 2-bit field won't allow writes to a page that is otherwise
  * write-protected.
  */
-#pragma GCC diagnostic push
-#pragma GCC diagnostic ignored "-Wpragmas"
-#pragma GCC diagnostic ignored "-Wattribute-alias"
 SYSCALL_DEFINE3(subpage_prot, unsigned long, addr,
 		unsigned long, len, u32 __user *, map)
 {
@@ -272,4 +269,3 @@ SYSCALL_DEFINE3(subpage_prot, unsigned long, addr,
 	up_write(&mm->mmap_sem);
 	return err;
 }
-#pragma GCC diagnostic pop

arch/powerpc/platforms/powermac/time.c

@@ -42,7 +42,11 @@
 #define DBG(x...)
 #endif
 
-/* Apparently the RTC stores seconds since 1 Jan 1904 */
+/*
+ * Offset between Unix time (1970-based) and Mac time (1904-based). Cuda and PMU
+ * times wrap in 2040. If we need to handle later times, the read_time functions
+ * need to be changed to interpret wrapped times as post-2040.
+ */
 #define RTC_OFFSET	2082844800
 
 /*
@@ -97,8 +101,11 @@ static time64_t cuda_get_time(void)
 	if (req.reply_len != 7)
 		printk(KERN_ERR "cuda_get_time: got %d byte reply\n",
 		       req.reply_len);
-	now = (req.reply[3] << 24) + (req.reply[4] << 16)
-		+ (req.reply[5] << 8) + req.reply[6];
+	now = (u32)((req.reply[3] << 24) + (req.reply[4] << 16) +
+		    (req.reply[5] << 8) + req.reply[6]);
+	/* it's either after year 2040, or the RTC has gone backwards */
+	WARN_ON(now < RTC_OFFSET);
+
 	return now - RTC_OFFSET;
 }
 
@@ -106,10 +113,10 @@ static time64_t cuda_get_time(void)
 
 static int cuda_set_rtc_time(struct rtc_time *tm)
 {
-	time64_t nowtime;
+	u32 nowtime;
 	struct adb_request req;
 
-	nowtime = rtc_tm_to_time64(tm) + RTC_OFFSET;
+	nowtime = lower_32_bits(rtc_tm_to_time64(tm) + RTC_OFFSET);
 	if (cuda_request(&req, NULL, 6, CUDA_PACKET, CUDA_SET_TIME,
 			 nowtime >> 24, nowtime >> 16, nowtime >> 8,
 			 nowtime) < 0)
@@ -140,8 +147,12 @@ static time64_t pmu_get_time(void)
 	if (req.reply_len != 4)
 		printk(KERN_ERR "pmu_get_time: got %d byte reply from PMU\n",
 		       req.reply_len);
-	now = (req.reply[0] << 24) + (req.reply[1] << 16)
-		+ (req.reply[2] << 8) + req.reply[3];
+	now = (u32)((req.reply[0] << 24) + (req.reply[1] << 16)	+
+		    (req.reply[2] << 8) + req.reply[3]);
+
+	/* it's either after year 2040, or the RTC has gone backwards */
+	WARN_ON(now < RTC_OFFSET);
+
 	return now - RTC_OFFSET;
 }
 
@@ -149,10 +160,10 @@ static time64_t pmu_get_time(void)
 
 static int pmu_set_rtc_time(struct rtc_time *tm)
 {
-	time64_t nowtime;
+	u32 nowtime;
 	struct adb_request req;
 
-	nowtime = rtc_tm_to_time64(tm) + RTC_OFFSET;
+	nowtime = lower_32_bits(rtc_tm_to_time64(tm) + RTC_OFFSET);
 	if (pmu_request(&req, NULL, 5, PMU_SET_RTC, nowtime >> 24,
 			nowtime >> 16, nowtime >> 8, nowtime) < 0)
 		return -ENXIO;

arch/x86/entry/entry_32.S

@@ -477,7 +477,7 @@ ENTRY(entry_SYSENTER_32)
 	 * whereas POPF does not.)
 	 */
 	addl	$PT_EFLAGS-PT_DS, %esp	/* point esp at pt_regs->flags */
-	btr	$X86_EFLAGS_IF_BIT, (%esp)
+	btrl	$X86_EFLAGS_IF_BIT, (%esp)
 	popfl
 
 	/*

arch/x86/entry/entry_64_compat.S

@@ -84,13 +84,13 @@ ENTRY(entry_SYSENTER_compat)
 	pushq	%rdx			/* pt_regs->dx */
 	pushq	%rcx			/* pt_regs->cx */
 	pushq	$-ENOSYS		/* pt_regs->ax */
-	pushq   %r8			/* pt_regs->r8 */
+	pushq   $0			/* pt_regs->r8  = 0 */
 	xorl	%r8d, %r8d		/* nospec   r8 */
-	pushq   %r9			/* pt_regs->r9 */
+	pushq   $0			/* pt_regs->r9  = 0 */
 	xorl	%r9d, %r9d		/* nospec   r9 */
-	pushq   %r10			/* pt_regs->r10 */
+	pushq   $0			/* pt_regs->r10 = 0 */
 	xorl	%r10d, %r10d		/* nospec   r10 */
-	pushq   %r11			/* pt_regs->r11 */
+	pushq   $0			/* pt_regs->r11 = 0 */
 	xorl	%r11d, %r11d		/* nospec   r11 */
 	pushq   %rbx                    /* pt_regs->rbx */
 	xorl	%ebx, %ebx		/* nospec   rbx */
@@ -374,13 +374,13 @@ ENTRY(entry_INT80_compat)
 	pushq	%rcx			/* pt_regs->cx */
 	xorl	%ecx, %ecx		/* nospec   cx */
 	pushq	$-ENOSYS		/* pt_regs->ax */
-	pushq   $0			/* pt_regs->r8  = 0 */
+	pushq   %r8			/* pt_regs->r8 */
 	xorl	%r8d, %r8d		/* nospec   r8 */
-	pushq   $0			/* pt_regs->r9  = 0 */
+	pushq   %r9			/* pt_regs->r9 */
 	xorl	%r9d, %r9d		/* nospec   r9 */
-	pushq   $0			/* pt_regs->r10 = 0 */
+	pushq   %r10			/* pt_regs->r10*/
 	xorl	%r10d, %r10d		/* nospec   r10 */
-	pushq   $0			/* pt_regs->r11 = 0 */
+	pushq   %r11			/* pt_regs->r11 */
 	xorl	%r11d, %r11d		/* nospec   r11 */
 	pushq   %rbx                    /* pt_regs->rbx */
 	xorl	%ebx, %ebx		/* nospec   rbx */

arch/x86/include/asm/pgalloc.h

@@ -184,6 +184,9 @@ static inline p4d_t *p4d_alloc_one(struct mm_struct *mm, unsigned long addr)
 
 static inline void p4d_free(struct mm_struct *mm, p4d_t *p4d)
 {
+	if (!pgtable_l5_enabled())
+		return;
+
 	BUG_ON((unsigned long)p4d & (PAGE_SIZE-1));
 	free_page((unsigned long)p4d);
 }

arch/x86/include/asm/pgtable.h

@@ -898,7 +898,7 @@ static inline unsigned long pgd_page_vaddr(pgd_t pgd)
 #define pgd_page(pgd)	pfn_to_page(pgd_pfn(pgd))
 
 /* to find an entry in a page-table-directory. */
-static __always_inline p4d_t *p4d_offset(pgd_t *pgd, unsigned long address)
+static inline p4d_t *p4d_offset(pgd_t *pgd, unsigned long address)
 {
 	if (!pgtable_l5_enabled())
 		return (p4d_t *)pgd;

arch/x86/include/asm/pgtable_64.h

@@ -216,7 +216,7 @@ static inline pgd_t pti_set_user_pgd(pgd_t *pgdp, pgd_t pgd)
 }
 #endif
 
-static __always_inline void native_set_p4d(p4d_t *p4dp, p4d_t p4d)
+static inline void native_set_p4d(p4d_t *p4dp, p4d_t p4d)
 {
 	pgd_t pgd;
 
@@ -230,7 +230,7 @@ static __always_inline void native_set_p4d(p4d_t *p4dp, p4d_t p4d)
 	*p4dp = native_make_p4d(native_pgd_val(pgd));
 }
 
-static __always_inline void native_p4d_clear(p4d_t *p4d)
+static inline void native_p4d_clear(p4d_t *p4d)
 {
 	native_set_p4d(p4d, native_make_p4d(0));
 }

arch/x86/kernel/e820.c

@@ -1248,6 +1248,7 @@ void __init e820__memblock_setup(void)
 {
 	int i;
 	u64 end;
+	u64 addr = 0;
 
 	/*
 	 * The bootstrap memblock region count maximum is 128 entries
@@ -1264,13 +1265,21 @@ void __init e820__memblock_setup(void)
 		struct e820_entry *entry = &e820_table->entries[i];
 
 		end = entry->addr + entry->size;
+		if (addr < entry->addr)
+			memblock_reserve(addr, entry->addr - addr);
+		addr = end;
 		if (end != (resource_size_t)end)
 			continue;
 
+		/*
+		 * all !E820_TYPE_RAM ranges (including gap ranges) are put
+		 * into memblock.reserved to make sure that struct pages in
+		 * such regions are not left uninitialized after bootup.
+		 */
 		if (entry->type != E820_TYPE_RAM && entry->type != E820_TYPE_RESERVED_KERN)
-			continue;
-
-		memblock_add(entry->addr, entry->size);
+			memblock_reserve(entry->addr, entry->size);
+		else
+			memblock_add(entry->addr, entry->size);
 	}
 
 	/* Throw away partial pages: */

arch/x86/mm/fault.c

@@ -641,11 +641,6 @@ static int is_f00f_bug(struct pt_regs *regs, unsigned long address)
 	return 0;
 }
 
-static const char nx_warning[] = KERN_CRIT
-"kernel tried to execute NX-protected page - exploit attempt? (uid: %d)\n";
-static const char smep_warning[] = KERN_CRIT
-"unable to execute userspace code (SMEP?) (uid: %d)\n";
-
 static void
 show_fault_oops(struct pt_regs *regs, unsigned long error_code,
 		unsigned long address)
@@ -664,20 +659,18 @@ show_fault_oops(struct pt_regs *regs, unsigned long error_code,
 		pte = lookup_address_in_pgd(pgd, address, &level);
 
 		if (pte && pte_present(*pte) && !pte_exec(*pte))
-			printk(nx_warning, from_kuid(&init_user_ns, current_uid()));
+			pr_crit("kernel tried to execute NX-protected page - exploit attempt? (uid: %d)\n",
+				from_kuid(&init_user_ns, current_uid()));
 		if (pte && pte_present(*pte) && pte_exec(*pte) &&
 				(pgd_flags(*pgd) & _PAGE_USER) &&
 				(__read_cr4() & X86_CR4_SMEP))
-			printk(smep_warning, from_kuid(&init_user_ns, current_uid()));
+			pr_crit("unable to execute userspace code (SMEP?) (uid: %d)\n",
+				from_kuid(&init_user_ns, current_uid()));
 	}
 
-	printk(KERN_ALERT "BUG: unable to handle kernel ");
-	if (address < PAGE_SIZE)
-		printk(KERN_CONT "NULL pointer dereference");
-	else
-		printk(KERN_CONT "paging request");
-
-	printk(KERN_CONT " at %px\n", (void *) address);
+	pr_alert("BUG: unable to handle kernel %s at %px\n",
+		 address < PAGE_SIZE ? "NULL pointer dereference" : "paging request",
+		 (void *)address);
 
 	dump_pagetable(address);
 }

arch/x86/platform/efi/efi_64.c

@@ -166,14 +166,14 @@ void __init efi_call_phys_epilog(pgd_t *save_pgd)
 		pgd = pgd_offset_k(pgd_idx * PGDIR_SIZE);
 		set_pgd(pgd_offset_k(pgd_idx * PGDIR_SIZE), save_pgd[pgd_idx]);
 
-		if (!(pgd_val(*pgd) & _PAGE_PRESENT))
+		if (!pgd_present(*pgd))
 			continue;
 
 		for (i = 0; i < PTRS_PER_P4D; i++) {
 			p4d = p4d_offset(pgd,
 					 pgd_idx * PGDIR_SIZE + i * P4D_SIZE);
 
-			if (!(p4d_val(*p4d) & _PAGE_PRESENT))
+			if (!p4d_present(*p4d))
 				continue;
 
 			pud = (pud_t *)p4d_page_vaddr(*p4d);

block/blk-core.c

@@ -3473,6 +3473,10 @@ static void __blk_rq_prep_clone(struct request *dst, struct request *src)
 	dst->cpu = src->cpu;
 	dst->__sector = blk_rq_pos(src);
 	dst->__data_len = blk_rq_bytes(src);
+	if (src->rq_flags & RQF_SPECIAL_PAYLOAD) {
+		dst->rq_flags |= RQF_SPECIAL_PAYLOAD;
+		dst->special_vec = src->special_vec;
+	}
 	dst->nr_phys_segments = src->nr_phys_segments;
 	dst->ioprio = src->ioprio;
 	dst->extra_len = src->extra_len;

block/blk-mq.c

@@ -1075,6 +1075,9 @@ static bool blk_mq_mark_tag_wait(struct blk_mq_hw_ctx **hctx,
 
 #define BLK_MQ_RESOURCE_DELAY	3		/* ms units */
 
+/*
+ * Returns true if we did some work AND can potentially do more.
+ */
 bool blk_mq_dispatch_rq_list(struct request_queue *q, struct list_head *list,
 			     bool got_budget)
 {
@@ -1205,8 +1208,17 @@ bool blk_mq_dispatch_rq_list(struct request_queue *q, struct list_head *list,
 			blk_mq_run_hw_queue(hctx, true);
 		else if (needs_restart && (ret == BLK_STS_RESOURCE))
 			blk_mq_delay_run_hw_queue(hctx, BLK_MQ_RESOURCE_DELAY);
+
+		return false;
 	}
 
+	/*
+	 * If the host/device is unable to accept more work, inform the
+	 * caller of that.
+	 */
+	if (ret == BLK_STS_RESOURCE || ret == BLK_STS_DEV_RESOURCE)
+		return false;
+
 	return (queued + errors) != 0;
 }
 

certs/blacklist.h

 #include <linux/kernel.h>
 
-extern const char __initdata *const blacklist_hashes[];
+extern const char __initconst *const blacklist_hashes[];

crypto/af_alg.c

@@ -1060,12 +1060,19 @@ void af_alg_async_cb(struct crypto_async_request *_req, int err)
 }
 EXPORT_SYMBOL_GPL(af_alg_async_cb);
 
-__poll_t af_alg_poll_mask(struct socket *sock, __poll_t events)
+/**
+ * af_alg_poll - poll system call handler
+ */
+__poll_t af_alg_poll(struct file *file, struct socket *sock,
+			 poll_table *wait)
 {
 	struct sock *sk = sock->sk;
 	struct alg_sock *ask = alg_sk(sk);
 	struct af_alg_ctx *ctx = ask->private;
-	__poll_t mask = 0;
+	__poll_t mask;
+
+	sock_poll_wait(file, sk_sleep(sk), wait);
+	mask = 0;
 
 	if (!ctx->more || ctx->used)
 		mask |= EPOLLIN | EPOLLRDNORM;
@@ -1075,7 +1082,7 @@ __poll_t af_alg_poll_mask(struct socket *sock, __poll_t events)
 
 	return mask;
 }
-EXPORT_SYMBOL_GPL(af_alg_poll_mask);
+EXPORT_SYMBOL_GPL(af_alg_poll);
 
 /**
  * af_alg_alloc_areq - allocate struct af_alg_async_req

crypto/algif_aead.c

@@ -375,7 +375,7 @@ static struct proto_ops algif_aead_ops = {
 	.sendmsg	=	aead_sendmsg,
 	.sendpage	=	af_alg_sendpage,
 	.recvmsg	=	aead_recvmsg,
-	.poll_mask	=	af_alg_poll_mask,
+	.poll		=	af_alg_poll,
 };
 
 static int aead_check_key(struct socket *sock)
@@ -471,7 +471,7 @@ static struct proto_ops algif_aead_ops_nokey = {
 	.sendmsg	=	aead_sendmsg_nokey,
 	.sendpage	=	aead_sendpage_nokey,
 	.recvmsg	=	aead_recvmsg_nokey,
-	.poll_mask	=	af_alg_poll_mask,
+	.poll		=	af_alg_poll,
 };
 
 static void *aead_bind(const char *name, u32 type, u32 mask)

crypto/algif_skcipher.c

@@ -206,7 +206,7 @@ static struct proto_ops algif_skcipher_ops = {
 	.sendmsg	=	skcipher_sendmsg,
 	.sendpage	=	af_alg_sendpage,
 	.recvmsg	=	skcipher_recvmsg,
-	.poll_mask	=	af_alg_poll_mask,
+	.poll		=	af_alg_poll,
 };
 
 static int skcipher_check_key(struct socket *sock)
@@ -302,7 +302,7 @@ static struct proto_ops algif_skcipher_ops_nokey = {
 	.sendmsg	=	skcipher_sendmsg_nokey,
 	.sendpage	=	skcipher_sendpage_nokey,
 	.recvmsg	=	skcipher_recvmsg_nokey,
-	.poll_mask	=	af_alg_poll_mask,
+	.poll		=	af_alg_poll,
 };
 
 static void *skcipher_bind(const char *name, u32 type, u32 mask)

crypto/asymmetric_keys/x509_cert_parser.c

@@ -249,6 +249,15 @@ int x509_note_signature(void *context, size_t hdrlen,
 		return -EINVAL;
 	}
 
+	if (strcmp(ctx->cert->sig->pkey_algo, "rsa") == 0) {
+		/* Discard the BIT STRING metadata */
+		if (vlen < 1 || *(const u8 *)value != 0)
+			return -EBADMSG;
+
+		value++;
+		vlen--;
+	}
+
 	ctx->cert->raw_sig = value;
 	ctx->cert->raw_sig_size = vlen;
 	return 0;

drivers/acpi/osl.c

@@ -45,6 +45,8 @@
 #include <linux/uaccess.h>
 #include <linux/io-64-nonatomic-lo-hi.h>
 
+#include "acpica/accommon.h"
+#include "acpica/acnamesp.h"
 #include "internal.h"
 
 #define _COMPONENT		ACPI_OS_SERVICES
@@ -1490,6 +1492,76 @@ int acpi_check_region(resource_size_t start, resource_size_t n,
 }
 EXPORT_SYMBOL(acpi_check_region);
 
+static acpi_status acpi_deactivate_mem_region(acpi_handle handle, u32 level,
+					      void *_res, void **return_value)
+{
+	struct acpi_mem_space_context **mem_ctx;
+	union acpi_operand_object *handler_obj;
+	union acpi_operand_object *region_obj2;
+	union acpi_operand_object *region_obj;
+	struct resource *res = _res;
+	acpi_status status;
+
+	region_obj = acpi_ns_get_attached_object(handle);
+	if (!region_obj)
+		return AE_OK;
+
+	handler_obj = region_obj->region.handler;
+	if (!handler_obj)
+		return AE_OK;
+
+	if (region_obj->region.space_id != ACPI_ADR_SPACE_SYSTEM_MEMORY)
+		return AE_OK;
+
+	if (!(region_obj->region.flags & AOPOBJ_SETUP_COMPLETE))
+		return AE_OK;
+
+	region_obj2 = acpi_ns_get_secondary_object(region_obj);
+	if (!region_obj2)
+		return AE_OK;
+
+	mem_ctx = (void *)&region_obj2->extra.region_context;
+
+	if (!(mem_ctx[0]->address >= res->start &&
+	      mem_ctx[0]->address < res->end))
+		return AE_OK;
+
+	status = handler_obj->address_space.setup(region_obj,
+						  ACPI_REGION_DEACTIVATE,
+						  NULL, (void **)mem_ctx);
+	if (ACPI_SUCCESS(status))
+		region_obj->region.flags &= ~(AOPOBJ_SETUP_COMPLETE);
+
+	return status;
+}
+
+/**
+ * acpi_release_memory - Release any mappings done to a memory region
+ * @handle: Handle to namespace node
+ * @res: Memory resource
+ * @level: A level that terminates the search
+ *
+ * Walks through @handle and unmaps all SystemMemory Operation Regions that
+ * overlap with @res and that have already been activated (mapped).
+ *
+ * This is a helper that allows drivers to place special requirements on memory
+ * region that may overlap with operation regions, primarily allowing them to
+ * safely map the region as non-cached memory.
+ *
+ * The unmapped Operation Regions will be automatically remapped next time they
+ * are called, so the drivers do not need to do anything else.
+ */
+acpi_status acpi_release_memory(acpi_handle handle, struct resource *res,
+				u32 level)
+{
+	if (!(res->flags & IORESOURCE_MEM))
+		return AE_TYPE;
+
+	return acpi_walk_namespace(ACPI_TYPE_REGION, handle, level,
+				   acpi_deactivate_mem_region, NULL, res, NULL);
+}
+EXPORT_SYMBOL_GPL(acpi_release_memory);
+
 /*
  * Let drivers know whether the resource checks are effective
  */

drivers/base/power/domain.c

@@ -2487,10 +2487,9 @@ EXPORT_SYMBOL_GPL(of_genpd_parse_idle_states);
  * power domain corresponding to a DT node's "required-opps" property.
  *
  * @dev: Device for which the performance-state needs to be found.
- * @opp_node: DT node where the "required-opps" property is present. This can be
+ * @np: DT node where the "required-opps" property is present. This can be
  *	the device node itself (if it doesn't have an OPP table) or a node
  *	within the OPP table of a device (if device has an OPP table).
- * @state: Pointer to return performance state.
  *
  * Returns performance state corresponding to the "required-opps" property of
  * a DT node. This calls platform specific genpd->opp_to_performance_state()
@@ -2499,7 +2498,7 @@ EXPORT_SYMBOL_GPL(of_genpd_parse_idle_states);
  * Returns performance state on success and 0 on failure.
  */
 unsigned int of_genpd_opp_to_performance_state(struct device *dev,
-					       struct device_node *opp_node)
+					       struct device_node *np)
 {
 	struct generic_pm_domain *genpd;
 	struct dev_pm_opp *opp;
@@ -2514,7 +2513,7 @@ unsigned int of_genpd_opp_to_performance_state(struct device *dev,
 
 	genpd_lock(genpd);
 
-	opp = of_dev_pm_opp_find_required_opp(&genpd->dev, opp_node);
+	opp = of_dev_pm_opp_find_required_opp(&genpd->dev, np);
 	if (IS_ERR(opp)) {
 		dev_err(dev, "Failed to find required OPP: %ld\n",
 			PTR_ERR(opp));